Search Documents

By S. B. King

IT is the purpose of this article to give those not familiar with the subject an idea of the extent to which coal is mined by machine in the United States; to describe some types of electrically operated coal cutters; and in particular, some of the latest improvements and developments in these machines. Generally speaking, the article deals with the mining of bituminous coal in room-and-pillar mines, as the use of undercutting machines in the anthracite region of Pennsylvania is in its infancy, and when machine mining is referred to bituminous coal is taken for granted. The number of mines in the United States that are operating on the long-wall principle is very limited, and the number of long-wall machines in use is a very small percentage of the total. The advantages of mining by machine may be summed up briefly as follows: A. Increased safety to property and life, due to the large decrease in the amount of powder required when the coal is properly undermined. B. Reduction in the cost of mining. C. Improvement in the quality of the product; and, consequently, increase in market value, due to the greater proportion of lump and screen sizes secured by machine mining. D. Increase in the capacity of the mine, and more rapid development of new mines. E. Ability to mine veins in which the height of the coal or the character of the roof has prevented mining by hand, on a commercial basis.

Jan 6, 1914

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

Jan 1, 1961

By ALEC CROWELL

This brief summary of oil and gas developments in Alabama, Florida and Georgia has been made possible through the courtesy of Stewart J. Lloyd, Assistant State Geologist of Alabama; Herman Gunter, Director, Florida Geological Survey, and Garland Peyton, Director, Georgia Department of Mines, Mining and Geology.

Jan 1, 1946

By AIME AIME

COUNCIL* PRESIDENT OF THE COUNCIL. JAMES F. KEMP NEW YORK, N. Y.. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. R. V. NORRIS WILKES-BARRE, PA. GARDNER F. WIILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) . KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Jul 1, 1912

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

Jan 1, 1963

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952

Jan 1, 1970

Jan 1, 1970

By C. M. Ball

The magnetic concentration of iron-ores has been so often and so widely studied and discussed among the members of the Institute that any remarks concerning its general importance, from an economic standpoint, would be superfluous; but it is thought that a description of the Ball and Norton ore-separator, designed for cobbing and separating magnetic iron-ores, indicating its essential differences from other machines and the advantages claimed for it, together with some account of recent results obtained in its application to the concentration of such ores, will prove of interest. This machine is the joint invention of Mr. Sheldon Norton, of Hokendauqua, Pa., and the writer, and has been patented in the United States, Canada, and other countries. Of the accompanying illustrations, Pig. 1 represents a longitudinal vertical section of the perfected ore-separator, adapted for separating fine ore, and Fig. 2 the same, adapted for cobbing ore of the size of stove- or chestnut-coal. The two designs are identical in principle, and vary from each other in minor details only. The apparatus consists of a partially-closed chest, having an opening at f, from the feed-hopper, h, through which the ore is delivered to the machine from an ore-pocket or storage-bin provided with means for regulating the flow of ore, so that, when the machine

Jan 1, 1891

By F. L. Grammer

In these day, when anthracite is less extensively used as a blastifurnace fuel than it was a generation ago, and managers endeavor to maintain regular and known ore-mixtures, the " freezing " of tuyeres, cinder-notch or iron-notch is infrequeut; and, consequently, the oil-burner or " kerosene blowpipe "* is seldom employed; and furnace-foremen have, to a considerable degree, forgotten their former cunning and persistency in the use of the drill and sledge. Still, in starting new or abandoned plants with untrained labor, and in running some of our large 100-ft. furnaces, slips, resulting in very cold furnaces, may occur, even under experienced managers. During my superintendence of the Cleveland, O., blast-furnaces, such a misfortune, owing to a dearth of trustworthy foremen, was experienced; and our electrician, Mr. Thomas Martin, proposed to open the tuyeres and cinder-notch by means of the heat of the electric arc. We have heard that the surface-cracks or marks developed in rolling heavy plates have been closed by electric welding, as by a soldering-iron, and also that an electric burner has been employed at some German blast-furnaces; but the experiment was quite novel to us; and I think it constituted one of the first, if not the very first, successful application of this device, for the purpose named, in the United States. †

Jan 1, 1902

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

By T. V. Philip, R. E. Lenhart

C. G. Dunn(General Electric Research Laboratory)— It is well recognized that understanding of the formation of the cube-on-edge texture in annealed commercial cold-rolled Si-Fe strip is important industrially as well as scientifically. I would like to make a few remarks on this subject, discuss some points in the present paper, and list two remaining problems that appear to be particularly outstanding. Attention should be drawn to the paper by P. K. Koh,23 which also considers the kinetics of secondary recrystallization in 3 pet Si-Fe, produced commercially by the Allegheny Ludlum Steel Corp. Koh covered a much larger temperature range than do either the present authors or P. N. Richards, whose work is mentioned in a footnote. Koh found an induction period (of short duration) even for isothermal anneals at 1260oC (2300°F). Koh and Dunn24 also found a change in texture during the 1260oC anneal for the same material. On the other hand, the material in coil D, according to Philip and Lenhart, underwent no sec-condary recrystallization, only continuous grain growth. The grade classifications of the four coils studied would suggest, however, that all four materials had developed the cube-on-edge or (110) [001] texture, but to varying degrees. Since no data on this are given and since watt loss depends

Jan 1, 1962

By Anders Carlson

NOTABLE advances have been made in the evaluation of oil-reservoir rocks from information furnished by core analysis. Among the physical data employed, per-meability is of primary importance. It may be assumed that the permeability of a core sample, considered as a property inherent to the nature of the porous medium only, is not markedly altered by the coring opera-tion, therefore some degree of accuracy is justified in the laboratory determination of permeability constants by means of homo-geneous flow media. To provide that such relatively simple determinations be sus-ceptible to duplication and consistent inter-pretation should prove advantageous in the prediction of subsurface flow conditions involving nonhomogeneous fluids. The air permeameter seems to fill most satisfactorily the need for rapid and fairly accurate determinations. Instruments that are similar in design and operation have come into general use. However, this has not resulted in an encouraging uniformity in the results obtained. Recognizing the value of reducing measured values to a common quantitative standard, the authors have sought to determine possible reasons for undue discrepancies and means for their elimination. This paper will be specifically concerned with three factors, which appear to be of some importance in the establishment of consistent permeability values: (I) design and operation of the permeameter, (2) preparation and mounting of the sample, (3) type of flow created in the sample.

Jan 1, 1940

By B. Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to he porous. In- deed, sponge iron, prepared by rcduction of the oxide in a reducing gas, is generally accepted as quite porous. with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig r shows commercial tungsten powder magni- fied at I0,000 X by the electron microscope,' both etched and unetched. In an earlier paper by one of the authors,* the existence of ports in tungsten powder was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these {pores} are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than IOO A. and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1949

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By E. E. Krist, W. H. Sweetser

Sampling of an orebody has a number of purposes. In the initial phase, it is necessary to define the limits of the orebody and mineral content to the extent that it can be stated whether it is, in fact, an economic orebody. Also, samples must be generated so that geological and metallurgical evaluations can be made. Finally, when sufficient information concerning the geology, mineralogy, and metallurgy are known, a mining method and plan can be developed and the metallurgical; plants constructed to process the ores as they become available. With today's large, complex open pit copper mines, single sampling methods would be inadequate. Diamond drilling, percussion drilling, underground shafts and drifts all play a part in the total orebody, definition. At Anamax Mining Company's Twin Buttes mine, sampling and orebody definition.wil1 eventually lead to the existence of three metallurgical processing plants and, perhaps, an underground mining operation. A 30 000 tons per day sulfide concentrator was placed in operation in September 1969 and a 10 000 tons per day oxide leaching plant was placed into service in May 1975. The aim of this presentation is to historically discuss the orebody sampling that has been done at Twin Buttes, briefly describe the orebody, and discuss the analytical methods currently used to assist the geologist, metallurgist and mine planner in their respective evaluations.

Jan 1, 1978

By W. P. Blake

Forty-five years have passed since I discovered the extensive and remarkable diatom-earth beds at Monterey, California., and now I have the satisfaction of bringing to notice still another wonderful deposit in the heart of Arizona. The Monterey beds mere described at the Philadelphia Academy,* and specimens were sent to Prof. J. W. Bailey, West Point, N. Y., at that time the leading American authority upon such microscopic relics of organic life. The earth from both localities is snow-white and pulverulent. It rubs off' like soft chalk upon the fingers when handled, and has the general appearance of chalk. But, unlike the Monterey beds, these newly-discovered deposits consist largely of volcanic ash, through which the siliceous shells of the diatoms are distributed. These deposits are in the central portion of the San Pedro valley,† in the southeastern corner of Pinal county. The region of their greatest development is a few miles south of the mining town of Mammoth, on the east bank of the stream, and near Redington, some 40 m. N. of Benson, on the Southern Pacific railway. The altitude is about 2600 ft. above tide. This portion of the San Pedro valley lies between the high Catalina and Rincon ranges on the west and the Galiuro mts. on the east. The Catalinas are composed chiefly of crystalline DIRECTOR OF THE ARIZONA SCHOOL OF WINES,

Jan 1, 1903