Search Documents

By Joseph Daniels

(San Francisco Meeting, October, 1911.) I. THE FRITZ ENGINEERING LABORATORY. TEE Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. . The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem, and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight, 84 ft. long and 9 ft. wide, in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section, containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Feb 1, 1912

By Wilbur H. Somerton

In order to evaluate the quantitative determination of porosity by various neutron logging systems, four test wells were constructed to simulate some of the possible variab1e.r found in field logging conditions. All of the test holes contain sections of limestone with one section of sandstone included in one well. Each well has a representative section of high, medium, and low porosity. Three borehole sizes are represented by three of the test wells, all containing fresh water. One test well contains saturated brine. Statistical and tune constant checks are made for each system evaluated. Runs and repeat runs are made with the sonde centered and eccentric. Factors evaluated are the effect of borehole size, sonde position, salinity, chemical composition of rock, and statistical variation. A semi-quantitative method of evaluation of these effects is used giving the average maximum per cent error possible for each. Drift and calibration procedures are also discussed. The effect of the various factors appears to be largely a function of the phenomena detected as well as the means of detection. Graphic illustrations of some of these effects are presented. It is concluded, that for accurate log interpretation, the hole size and sonde position should be known. INTRODUCTION The use of neutron logs for the derivation of porosity has become an accepted practice in many areas. In recent years, many different neutron logging systems have been offered to the industry. The neutron sources presently available are of the radium-beryllium or polonium -beryllium type. Detector types used are ionization chambers, Geiger-Mueller-type counters, proportional counters, or scintillation detectors used to detect or measure gamma rays, thermal neutrons, epithermal neutrons, fast neutrons or combinations of these. It is well-known that all systems do not respond alike in all environments. As a result, testing facilities and an evaluation method were developed for use in evaluating the porosity discriminating ability of neutron logging systems using conditions simulating those normally encountered in the field. With such an evaluation, the suitability of a logging system can be determined lor selected field conditions. TEST FACILITIES The testing facilities consist of wells containing rocks of various porosities, constructed to include as many parameters as practicable. Three pits were drilled to a depth of 20 ft and the fourth to a depth of 9 ft, all having 48-in. diameters. Rat holes were dug to a depth of 6 ft in the center of each pit and fitted with sections of pipe having appropriate diameters. The top of this pipe was located approximately 8 in. above the pit bottom. A 6-in, layer of cement was then poured on the bottom and while still wet, 42-in. OD corrugated, galvanized culvert pipe was set on bottom and centered in place. This pipe extends approximately 1 ft above the surface of the ground. The annulus around the culvert pipe was then filled with cement to the top. A 1- or 2-in. layer of sand was placed on the cement bottom to provide an adjustable bed on which to place the series of rocks set in each hole. A cross section of a typical test well containing the porous rocks is shown in Fig. 1.

By Herbert J. French

Herbert 1. French (Member 1934), vice president of the International Nickel Co. Inc., assistant vice president of the International Nickel Co. of Canada Ltd., and AIME Howe Memorial Lecturer for 1956, died in Rochester, Minn. on Aug. 17, 1955, after a long illness. Before his death, Mr. French had laid the foundation of research on which the Howe Memorial Lecture (p. 770) was based. His associates at Inco, 0. 0. Miller and J. W. Sands, were able to complete the project, present the lecture, and prepare it for publication, following Mr. French's general outline. Born in New York on May 27, 1893, he graduated from the School of Mines, Columbia University, with a degree in metallurgical engineering in 1915. Mr. French gained his early engineering experience with the American Smelting and Refining Co., serving as a chemist and as-sayer at the company's Murray, Utah, installations. He later returned east and became a metallurgical engineer for the General Vehicle Co., Long Island City, IT. Y., a subsidiary of the General Electric Co. In 1917 Mr. French was appointed civilian inspector of materials for the U.S. Army Signal Corps, and continued this work when it was later absorbed into the Bureau of Aircraft Production. Subsequently he was appointed district inspector in Philadelphia for the Pittsburgh (Ordnance Metallurgical) office, later transferring to Pittsburgh. After World War I Mr. French became an assistant physicist on the metallurgical staff, U. S. Bureau of Standards, Washington, D. C. During his years with the Bureau, he was successively associate physicist, metallurgist, senior metallurgist, and assistant chief, division of metallurgy. In 1929 Mr. French joined International Nickel as a metallurgist at the company's Bay-onne, N. J., research laboratory. Transferring to the development and research division, New York, in 1931, he took charge of alloy steel and iron development, becoming assistant manager of this division in 1943. Mr. French's appointment as an Inco vice president came in March 1947. Previously, he was appointed assistant vice president of the International Nickel Co. of Canada Ltd. in January 1947. Mr. French served the War Production Board during World War II as senior technical consultant in charge of the metallurgical and specifications section of the iron and steel branch. When this section of the WPB was organized into the steel division, he was appointed chief of the metallurgical branch. From March 1944 to September 1945 Mr. French served as assistant director. Herbert French was well known not only for his prolific contribution to the metallurgical literature, for which he received numerous awards, but also for his prolonged service to the profession through its technical societies. He was a past president of ASM, and was the Campbell Memorial Lecturer for that group in 1933. Mr. French was honored by the American Society for Steel Treating in 1931 when he was awarded the Henry Marion Howe Medal. A series of lectures he gave in 1941 before the Fourth Western Metal Congress in Los Angeles was later published in book form under the title Alloy Constructional Steels.

Jan 1, 1957

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7'8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By Charles C. Rodd

PRIOR to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (1) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types of tests are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. IN the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce" was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equipment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction set-up, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators were beginning to suspect that the high rates of production maintained during "potential" tests were conducive to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term "productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1942

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By N. L. Muench, J. S. Osba

Research conducted previously has demonstrated that spectral analysis of gamma radiation from the naturally radioactive elements present in earth materials permits detervination of the relative concentrations of these elements. This research suggested that spectral analysis of gamma radiation resulting from neutron bombardment of elements not nor-mally radioactive might serve to identify these non-radioactive elements, and might permit their quantitative determination. To investigate this possibility, laboratory experiments were conducted in which various earth materials were subjected to bombardment by neutrons from a polonium-beryllium source, and in which the spectra of the resultant gamma radiation were analyzed. The geometry of the lab-ortory system was designed to simulate wellbore conditions. The laboratory work demonstrated that some elements not only can be identified with relative ease, but also can be determined quantitatively. This finding indicates that the use of an intense source of more energetic neutrons may lead to the identification and measurement of additional elements of interest by means of induced nuclear reactions. INTRODUCTION In recent years the applications of nuclear physics to the producing branch of the petroleum industry have become increasingly numerous. One significant development, an outgrowth of nuclear science which is of potential importance in well logging, has been the analysis of gamma-ray spectra of naturally radioactive elements in earth strata. The work of Brannon and Osoba1 has demonstrated that presently available equipment and techniques may be used to determine the relative concentration of thorium, potassium, and uranium in underground strata by means of gamma-ray spectral analysis. Success of the research on spectral analysis of naturally radioactive elements suggested that spectral analysis of induced radioactivity might serve to identify, and perhaps measure quantitatively, those elements which normally are not radioactive, but which become radioactive on neutron bombardment. It was to investigate this possibility that the research described in the following sections was undertaken. THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bom- barded with neutrons, emits gamma rays of energies characteristic of that element. Therefore, in theory, an element may be identified by analysis of the energy spectrum of the neutron-induced gamma radiation. If a neutron impinges upon the nucleus of an atom, any one of several reactions may occur. For identification of elements in earth formations the more important are listed below: 1. The neutron may be elastically scattered, as in a collision between two billiard balls. In this case the total kinetic energy is conserved, and no nuclear radiation is emitted. 2. The neutron may be inelast-ically scattered, as in a collision between two automobiles in which case the total kinetic energy is not conserved. The lost kinetic energy reappears in the form of gamma radiation. 3. The neutron may be captured, in which case the neutron becomes a part of the target nucleus, and a gamma ray is emitted. For example, if the target nucleus is H1, the pro-duced nucleus will be H3, and gamma radiation of a particular energy will be emitted. 4. The neutron may produce nuclear fission, or may enter into miscellaneous reactions which result in the emission of

Jan 1, 1958

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,&apos; Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1&apos;700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.&apos; and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel&apos; "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.&apos; EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By C. R. Johnson, R. A. Greenkorn, E. G. Woods

A new method of reservoir evaluation called pulse-testins has been developed for describing formation properties between wells. Pulse-testing utilizes a sensitive differential-pressure gauge at a responding well to measure and record the response generated by a series of flow rate changes (pulses) at an adjacent or pulsing well. Since the pulse-test instruments have a sensitivity of about 0.001 psi, pulses of several hours or less in duration will generate a measurable response in most reservoirs. For this reason, many well pairs can be tested in a short period of time with little interference in field operations. Comparison of pulse-test results to conventional testing methods shows that the pulses obey unsteady-state, compressible-flow theory and thus provide a measure of both transmissibility (kh/µ) and storage (Fch). In additian, the method can be used qualitatively to describe communication across faults and between zones, and direction and tnagnitude of fracture trends. INTRODUCTION To obtain maximum usefulness of new reservoir analysis methods as well as to aid the field engineer in understanding local reservoir anomalies, improved methods are needed to describe heterogeneities in specific reservoirs. Optimum well spacing, equipment specifications, well completion design and especially the economics of pressure maintenance and secondary recovery programs depend on the extent and location of the heterogeneities that affect flow behavior in the field. One method for obtaining a measure of areal reservoir heterogeneity is an interference test. In the simplest interference test. constant-rate production or injection is initiated at one well and the effect of this flow is measured as pressure vs time at another well. Thus, during interference tests the flow characteristics of the formation are determined in situ. Despite their obvious usefulness in reservoir delineation. interference tests have not enjoyed frequent usage. Reasons for this have been the weeks or months required in many fields to obtain a pressure response measurable with conventional gauges, and the interruption of routine field operation during the field-wide shut-in normally required during these long times. Also, only average properties of the relatively large volume of the reservoir disturbed during these long times can normally be obtained — variations in properties between individual wells cannot be delineated. To eliminate these drawbacks of conventional tests, a special reservoir description technique called pulse testing&apos; has been developed. Pulse-testing has several advantages that make it more convenient and practical for field use than interference tests. Valid tests are more certain because use of a series of flow disturbances gives rise to a diagnostic pressure response that can more readily be distinguished from unknown trends in reservoir pressure and other "noise." The time required is only a fraction of that for an interference test because a special, high-sensitivity differential pressure gauge can detect a much smaller pressure change. Variations in properties between individual wells can be delineated because of the relatively small volume of the reservoir disturbed during these short times. Finally, wells other than the pulsing and responding wells do not have to be shut in or carefully regulated.

Jan 1, 1967

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

IN a search for an improved conductor for use in field wire for the L. S. Army Signal Corps, an alloy of copper and silver was developed from which it was possible to obtain 29 B & S ga. strands with tensile strengths in excess of 160,000 psi combined with an electrical conductivity of over 70 pct IACS. Such a favorable combination of strength and electrical conductivity has not been reported previously in the rather extensive literature covering this subject. The properties obtained from various binary alloys of copper and silver, together with the method of fabrication of these alloys which has been developed to obtain the properties desired in fine wire strands, are discussed in this paper. LITERATURE The effect on the electrical conductivity of copper of the various elements in solid solution is shown in Fig I, taken from published data by J. O. Linde and others.&apos; It will be noted that silver in solid solution depresses the electrical conductivity to a lesser extent than any other element for which data are given, and is followed rather closely by cadmium, and then by chromium. Zinc, which lies between cadmium and chromium, has so high a solid solubility in copper that the data for zinc are scarcely comparable to the data for the other two in the range covered. Not many data are available on the strain hardening of copper-rich Cu-Ag alloys. Corson2 reports a 3 pct Ag alloy properly cold worked and annealed to have 100,000 psi tensile strength and 90 pct IACS conductivity. On straight cold working, Hessenbruch3 reports 101.000 psi for a 5 pct Ag, 0.3 pct Be alloy, and 129,000 psi for a 30 pct Ag, 0.5 pct Be alloy. Here it would he expected that much of the strain hardening came from the silver content of the alloys. The copper-rich side of the Cu-Ag diagram, according to Stockdale,4 is shown in the upper part of Fig 2. The electrical conductivities for copper-silver alloys annealed at 750 and 350°C, taken from the work of Johansson and Linde,5 are shown in the lower part of Fig 2. The sloping line corresponds to the conductivity of solid solutions of silver in copper, and the horizontal offshoots correspond to the conductivity of the two-phase alloys in equilibrium at the two temperatures shown. The electrical conductivities are very high, even for the 750°C anneal. The potentiality for age hardening from supersaturated alpha copper solutions appears to be excellent from the solubility line, but Smith and Lindlief6 have shown that the response to age hardening of solution-annealed alpha alloys is not good. They found that the tensile strength of a 5 pct Ag alloy aged at various temperatures was not as great as in the quenched condition, even though, anomalously, the hardness increased from RB68 to RB78 by annealing for 4 hr at 400°C after a 750°C quench. Weist7 also found that the alloys increased in hardness

Jan 1, 1948

By A. J. Garnier, N. H. van Lingen

Rock downhole is known to be lesc. drillable than when brought to the surface. This must be ascribed mainly to the presence under downhole conditions of a pressure differential across already made chips, which hinders their being lifted. The pressure differential has partly a static and partly a dynamic origin. Balling-up of bits is another consequence of this pressure differerztial. Reduction in penetration rate owing to an increase in the strength of the rock is governed by the difference between the mud pressure and the pressure of the for/nation pore liquid. Rotationally symmetric geostatic stresses have 170 effect on drillability. Fracture of rock when drilling will be brille in most cases. The above is supported by laboratory drilling experiments with drag bill and roller bits an elevated mud, pore, and confining pressures On rocks differing in strength and permeability. INTRODUCTION In oil well drilling drillability of rock is found to decrease with increasing depth of the hole. Naturally deep rock will be more compacted and, therefore, harder to drill than shallow rock of the same type. However, apart from this the drillability of a sample of deep and compacted rock brought to the surface is generally much higher than in its original location downhole. In view of the economic implications of this reduction in drillability, it seems worthwhile to analyze its causes. The origin clearly has to be sought in the difference of environment. The only conceivable factors would seem to be the presence of mud under pressure, the pressure of the formation pore liquid, and the overburden of the rock. Down the borehole the rock is compressed triaxially by mud pressure and overburden. It is well known that the strength of rock is increased when confined by external pressure1. Various authors have, therefore, ascribed the difference in drillability mainly to the strengthening of rock by triaxial compression. Another factor, mentioned by Bobo and Hoch5, is that forces. including "pressure differential forces", tend to hold a dislodged particle in place. However, the conditions determining their magnitude are not clarified nor is their effect on drilling rate assessed. In the laboratory, drilling experiments on pressurized samples of rock yielded evidence that pressure differential forces holding the chips down are the major factor in reducing rate at depth. This paper describes the experiments and shows how the results enable both a qualitative and a quantitative interpretation of the factors determining the effect of chip hold-down on drilling rate. The implication with respect to balling-up and jet action is also discussed. The greatcr part of the experiments were performed in the pressure vessel shown in Fig. 1. The spacc between the sample of rock and the vesscl is divided by "0" rings into three separate chambers. The rock sample is confined laterally by pressurized oil in thc middle chamber. Penetration of oil into the sample is prevented by partly jacketing it with brass foil. Thc pressure of the drilling fluid in the hole can be adjusted via the upper chamber. Permeable rock specimens arc water saturated before being drilled. With a properly plastering mud as drilling fluid the pressure of the pore water can be adjusted independently via the lower chamber.

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965