Search Documents

By R. Stefanko

The use of strain gauges and compression pads for an underground bolt installation in a central Pennsylvania coal mine revealed that satisfactory anchorage could not be maintained in the shale stratum that constituted the immediate roof. Comprehensive laboratory tests resulted in a new shell designed with an increased area of contact and smaller surface serrations. Retightening of the bolt was also found to be beneficial for maintenance of high load values. Roof bolting in coal mines has progressed very rapidly in the last decade, and today this method of support is in general use. There are many theories concerning the functions of roof bolts, but the importance of beam building is indisputable. Proper tension in the bolts minimizes shearing along bedding planes and creates a thick, competent beam from individually weak layers. Bolting must be accomplished immediately upon exposure of the roof, and bolt tension must be maintained if roof failure is to be prevented. Seams are being mined today with roof bolt support where conventional timbering was not effective.' The widespread use of continuous mining equipment was made possible by roof bolts which permit long supported spans free of obstructions. Since adequate anchorage is the key to successful bolting, better methods for determining the efficiency of anchorage are continually being sought. Attempts have been made to measure bolt loads, thus assessing anchorage efficiency by employing sensing devices between the bolt head and roof. 3-s None of the techniques appears to be very accurate, and all have at least one serious deficiency. The greatest efforts are being directed toward the standardization of the pull test.6" Nevertheless, the author believes that the pull test is only one criterion for establishing the efficiency of anchorage and not necessarily the most important one. The conventional pull test involves the short-term application of forces, whereas the success of roof bolt installations is dependent upon the ability of anchorage to sustain relatively long-term forces. Therefore, it would appear that the time-dependent function of the anchor is the single most important parameter for the success of roof bolting in many types of rocks. UNDERGROUND TESTS Strain gauges and compression pads were employed to measure bolt loads in a central Pennsylvania coal mine.8 Bolting had been employed only sporadically in the shale top since dubious benefits were obtained with this type of support. Table I shows some typical results from this investigation. Anchorage losses were extremely variable among the bolts, but all showed a considerable degree of bleed-off. The tests indicated that anchorage efficiency was extremely low in this type of shale. The results confirmed that bolting under these conditions was practically worthless, and thus a waste of material and labor. Probably even more important, bolting constituted a hazard when reliance was placed upon it for support. Certainly the complete lack of confidence in roof bolting, which was apparent in the mine personnel, was justifiable since the bolts did not accomplish their purpose. PRELIMINARY LABORATORY BOLT TESTS The extreme losses in bolt tension that were detected in underground installations prompted a comprehensive study to assess the causes. However, preliminary studies were first made to determine the combined stresses in a roof bolt and to prove conclusively that the observed bleed-off phenomena were due to anchorage: slippage and not to some other physical manifestation. In all of the ensuing tests

Jan 1, 1962

By D. J. Carney, R. L. Stephenson

M. O. Holowaty (Inland Steel Co., Chicago)—Messrs. Stephenson and Carney should be commended on the presentation of this very interesting paper. They have introduced new ideas on sampling of sinter and have thereby made a valuable contribution to the qualitative evaluation of sinter. The paper undoubtedly presents a novel approach to the problem of sinter sampling and this is to be regarded as its main value. Sampling of sinter from the pallets prior to the discharge is by no means new. This sampling procedure was used in the past by Philbrook; Hamilton and Ameen and others. The sampling basket used by the authors of this paper, however, permits one actually to obtain a good sample of the sintering mixture. The basket which can also be described as a removable pallet goes then through the entire process of sintering and thus offers a sample which is positively representative of the batch in question. The authors' method of evaluating physical properties of sinter seems to be not altogether clear, however. It is felt that the following points should be clarified: I—In the section describing the shatter test the authors state that a 5-lb sample was used in the actual tests. There is no mention of the initial size of sinter particles used and the method of obtaining this 5-lb sample from the sinter cake weighing about 100 to 120 lb. It is also surprising that the sample was dropped from a height of 3 ft instead of the conventionally used 6 ft. Unfortunately there is no mention of the number of drops to which the sample was subjected. 2—The tumbler test used by Messrs. Stephenson and Carney in testing the samples of iron ore sinter was performed in a standard ASTM coke tumbling drum. The drum measures 3 ft in diam and is equipped with two 3-in. lifter bars. The distance of fall in this testing drum is identical with the distance used in the previously described shatter test. The number of drops in the tumbling drum is approximately double the number of revolutions. The basic difference then between the drop-shatter test used by Stephenson and Carney and the tumbling test seems to be the number of drops to which the sample is subjected and the abrasive action to which the sinter particles are exposed in the rotating drum. In any case, the choice between the shatter test and the tumbler test seems to be only a matter of taste and convenience. 3—The authors of the paper state that "in order to insure getting results that were representative . . . the entire sample obtained by means of the sampling basket was used as the starting material for the tumbler test. If the sample broke in pieces, all the pieces were used regardless of their size." The initial size of the material is known to be a very important factor, influencing seriously the final size of the particles. This should be particularly important in case of hard sinters. It seems also very troublesome and inconvenient to charge 12-in. cubes of sinter weighing about 100 lb into the testing drum. This could be eliminated by taking a standard fraction of somewhat smaller particles.

Jan 1, 1954

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.'-* Author's Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully's electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully's "precipitate1' density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O'Connor and Buchanan' however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By J. A. Snyder, W. L. Finlay

G. Edmunds—Solid solubility is considered to be of either the interstitial or the substitutional type. Is it possible, in a binary alloy as the simplest case, that some of the solute atoms are present in the normal lattice sites (substitutionally or filling lattice vacancies) while simultaneously others are in interstitial positionss One might even ask whether a distribution of the two types may be the normal situation. H. M. Meyer—Metastable states of interstitial atoms occupying vacant lattice sites possibly occur as well as of substitutional atoms squeezed in between regular matrix positions. However (as we know since Hume-Rothery), the solute atoms choose between the two kinds of solutions; consequently, every solute will be unequivocally either substitutional or interstitial in the equilibrium state of the solid solution. M. Balicki—In view of the fact that the authors apparently correlate the analysis of the alloys at the ingot stage with the properties exhibited at the testing stage, I would like to ask whether this is a fully justifiable procedure. In other words, how good are their determinations of solute concentration for correlating them with the mechanical properties. The answer to this question may explain some of the divergencies. Assuming good enough homogenization of the samples and exact determination of mechanical properties the position of the plotted experimental points will depend solely upon the accuracy of composition determination. If this is not accurate, say due to loss or pickup of elements during processing from the ingot to the testing stage, or due to a systematic error in the method employed for obtaining solute concentration data, the points will deviate from their true position and may align themselves along a different curve than the one expected. H. V. Kinsey—We have been studying the creep-rupture properties of titanium-base alloys at 1000°F. In the course of this work, anomalies in behavior of the alloys that would suggest that the material under test was becoming stronger as the test progressed have been observed. If this was so, the most likely explanation that we could think of was that the test bars were absorbing oxygen and nitrogen from the air during the test and were thereby becoming strengthened. In an attempt to determine the strengthening effect of absorbed oxygen and nitrogen the following experiment was conducted. A length of cold-rolled titanium was supplied by the E. I. du Pont Co. Two test bars, having a 1/4 in. diam gauge length, were prepared from this material. One bar was tested in the as-received condition. The second bar was heated in air at 1550°F for 100 hr and subsequently air cooled prior to testing. A testing temperature of 1000°F was employed. The results of these tests are tabulated in table 11. In the author's opinion, is it reasonable to assume that the bar that was exposed to air at 1550°F for 100 hr was stronger because it absorbed oxygen and nitrogen from the air during this heat treatment? W. L. Finlay (authors' reply)—Direct experimental evidence for or against Mr. Edmunds' interesting suggestion will probably never be available. It seems possible, however, that mixed interstitial-substitutional solid solution might well occur with interstitial elements. The less likely possibility of interstitial solution of a normally substitutional element like copper in aluminum was recently discussed at length by the

Jan 1, 1951

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By J. S. Crump, H. L. Stone

Laboratory studies have indicated that displacement of oil from a reservoir by means of a condensing gas drive results in extremely high oil recovery, approaching 100 per cent under the most favorable circumstances. A condensing gas drive is defined as a gas drive in which the gas utilized is appreciably soluble in the oil it is displacing. The laboratory studies consisted of a number of gas drive displacement experiments, all using a horizontal, sand-packed, steel tube as the laboratory reservoir. The experimental results indicate that the more soluble a gas is in the oil to he displaced, the more efficient that gar is as a displacing fluid. Experiments were conducted utilizing both a light, volatile crude and a heavy, asphalt crude as the in-place oil. In both cases, oil recovery was appreciably enhanced by solubility of the displacing gas. It is believed that the use of condensing gas drives would result in increased oil recovery from many reservoirs during either primary or secondary phases of production. INTRODUCTION Since the early days of the oil industry there has been an increasing awareness of the problems of oil recovery. During the last few decades particularly a growing recognition of the problems has led to widespread attempts on the part of the industry to increase oil recovery by improved technology. One method which has been used to increase recovery is the maintenance of reservoir pressure by injection of gas. Part of the beneficial effect resulting from this gas injection was to prevent evolution of the gas dissolved in the reservoir oil, since such evolution would cause the oil to shrink and become more viscous, thereby adversely affecting oil recovery. In most instances, the gas injected was predomillantly methane, and so the possibility of oil recovery by retrograde vaporization existed. Laboratory investigations of displacement of reservoir oils by methane, carried out at high pressure, have indicated that considerable additional recovery of light oils could be effected by vaporization, but only at the cost of a severe volumetric shrinkage of the residual oil which would cause a decrease in relative permeability to oil in the reservoir. Consequently, recovery of oil by physical displacement would be impaired. The study suggested, therefore, that recovery of oil might be enhanced by injecting into the reservoir a gas known to be appreciably soluble in the oil at reservoir conditions. Swelling of the oil due to solution of gas should result and yield a consequent increase in the relative permeability to oil. The work described in the following sections was, therefore, undertaken to investigate the possibility of increased recovery by this mechanism. Research similar to that reported in this paper has been conducted by The Atlantic Refining Co.1,2,3 In these studies, Whorton, et al, and Slobod, et al, used methane-rich gas to displace oil from model reservoirs. Solubility of the gas was achieved by keeping the reservoir pressure greater than the saturation pressure of the original oil, and the degree of this solubility was varied by operating at different reservoir pressures. Thus the Atlantic project was primarily a study of the effect of reservoir pressure upon oil recovery by gas drive. The objective of the work reported in this paper was to study the effect of gas composition upon oil recovery while holding the reservoir pressure constant. DESCRIPTION OF EXPERIMENTS The discussion of the preceding section suggests that

Jan 1, 1957

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A 1/2x4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four 5/s in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of 3/s yard capacity, both manufactured by Blaw Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1950

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low grade molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported. In the chlorination process, a gaseous mixture of chlorine and oxygen in the volume ratio bf 2:5 has been passed at 1.66 x 10- 5 m3/s for 1800 s over a 0.01 kg batch of molysulfide concentrate at a temperature of 573°K. Most of the molybdenum has been volatilized as molybdenum oxychloride which has subsequently been extracted in water. The molybdenum value from the aqueous solution has been recovered in the form of calcium molybdate (CaO.MoO3) by treatment with calcium chloride (CaCI2). In an alternative processing scheme, the molybdenum rich solution has been treated with an oxidizing agent (K2S20f.J) and allowed to boil to recover a major portion of the molybdenum value in the form of molybdic oxide (MOOS). The spent charge obtained after molysulfide chlorination has been mixed with about 1 wt % sodium chloride and heated at 773K under an oxygen atmosphere. The reacted mass has been water-leached to yield a nickel-copper bearing solution with limited iron. The process liquor appears to be well suited for further processing by known hydrometallurgical recovery processes for nickel and copper. In the conventional process of molybdenum extraction, the molysulfide concentrate (-59% Mo) is first subjected to roasting to produce molybdic oxide. The oxide is then further processed in sequential steps involving vacuum distillation, ammonia leaching, and calcination to higher purity prior to hydrogen reduction to metal. In India there is at present some small tonnage production of molysulfide concentrate from a byproduct recovery plant of the M/s. Uranium Corp. of India Ltd. (M/s UCIL), Bihar. Efforts are being made at this laboratory to process the low grade fraction of the concentrate which contains sulfides of copper, nickel, and iron; quartz; and chlorites. Here, the conventional routes involving roasting and vacuum distillation appear unsuitable to produce an acceptable quality of molybdic oxide at high recoveries. Formation during roasting molybdates of some of the impurities present in the sulfide concentrate make subsequent vacuum distillation less efficient. In view of these problems, in earlier work reported from this laboratory the low grade concentrate has been processed hydrometallurgically to P. produce calcium molybdate. Starting from this molybdenum intermediate, processes have also been developed for the production of molybdenum and ferromolybdenum. Chlorination as an alternative to roasting for metal sulfides has been drawing considerable interest. The high reactivity of chlorine, the relatively low temperature of operation, the suitability of application to low grade resources, the convenience of recovering sulfur in non-polluting form, and the purity of chlorides which are separated by distillation all favor chlorination. In recent years, considerable work has been reported on the chlorination of common metal sulfides. In the field of molybdenum extraction from its sulfide resource, use of chlorination technology has been rather limited. Senderoff and Labrie3 were the first to chlorinate molysulfide concentrate with elemental chlorine at about 823°K to molybdenum pentachloride for use in the electrolytic preparation of molybdenum. The only other reported work, by Haver, Uchida and Wong, involved reaction between molysulfide and chlorine at 673°K to recover sulfur. The reaction products were, however, identified as molybdenum pentachloride and sulfur monochloride.

Jan 1, 1979

By David C. N. Cockburn

INTRODUCTION This paper analyses certain of the financial considerations which will commonly apply in relation to the following questions: - what equity structure or project vehicle should be adopted for the exploration and/or exploitation of a project by more than one unrelated participant? - what vehicle should be adopted by a participant for its participation in a multiparty project? Due to local, politically motivated laws in certain jurisdictions, or due to the overriding requirements of a dominant participant, there may be little choice of the underlying multiparty structure which may be adopted for the exploration, appraisal and/or development phases of a project. Nevertheless, even in such circumstances, attention should be given, at least in the preparation of the related documentation, or in considering methods of participating or funding the project, to certain of the points discussed below. This discussion of financial considerations in the context of the more commonly adopted multiparty structures concentrates primarily on fiscal, financial accounting, financing and funding aspects. TYPES OF PROJECT VEHICLE FOR MULTIPARTY INTERESTS The well known types of vehicle adopted for the participation in a project by more than one participant (assuming that the participants are effectively unrelated) are as follows. Joint Venture (unincorporated joint venture) By far the most commonly adopted structure for mining ventures, a joint venture is usually defined and documented in terms to distinguish it from a partnership for important tax and legal reasons. In essence, this is a contractual association of more than one participant to carry out a specific commercial project or purpose. The relationship between the separate participants and their respective rights, interests, obligations and liabilities are agreed between the participants in one or more contracts (viz Joint Venture Agreements or Joint Operating Agreements together with ancillary documentation). Unlike other project vehicles of participation, in most jurisdictions there is no specific body of law governing joint ventures. The participants thus enjoy contractual freedom to negotiate whatever deal they may wish between themselves. Jointly-Owned Project Company (corporate joint venture) A very familiar vehicle, this is a separate and distinct legal and tax entity incorporated under the company laws of the place of incorporation to undertake specific objects, and granted specific powers, in relation to the Project. Although certain rights, interests and obligations may be circumscribed in the governing corporate instruments by the promoter participants, the corporation laws of the relevant place of incorporation, and the selection of such governing laws (assuming freedom of choice) and future political changes in such corporate laws, should be carefully considered. The use of a company in a multiparty structure may be peripheral to the project itself as a specific purpose vehicle (for example, a joint sales agent or marketing company or a joint borrowing vehicle) or it may form a central function such as in the case of a tolling company which will own the project for legal and taxation purposes and raise financing with the backing of the shareholder participants commonly by the adoption of take-off, throughput and/or user agreements. Partnership This is a legal relationship, subject to the often wide-sweeping restrictions of the relevant local partnership laws, under which the participants have agreed to carry on a business venture together with a view to profit. The effect of the relevant partnership laws, as well as the various types of partnerships and the

Jan 1, 1985

By Murray Pezim

In the good old days of the folklore of the mining industry, grizzled prospectors obtained a few loose dollars from friends and neighbours then wandered off to eventually return with the great discovery which became the core of the new corporate empires. Alternatively, merchant banking barons obtained exclusive rights to just about anything of future value over hugh nation-size territories. Some of this probably still goes on, likely with about the same ineffectiveness and waste of effort and money as in the past. CURRENT CONCERNS IN MINING In today's difficult climate in the mining industry, for that matter in all industry, effectiveness is the vital consideration. Cost effectiveness -- more bang for the buck -- is especially important in such an area of high risk as mineral exploration. And there are other factors to consider. Since minerals are depleting resources, the mining inddustry is constantly confronted with the reality that those resources extracted today must be immediately replaced if a resource enterprise is to continue. And if growth is to be achieved, even more resources must be found to support future expansion. The current and immediately foreseeable climate internationally for the mining industry creates a special need and urgency for aggressive and successful exploration, certainly in Canada, if not also in the United States. Depressed world markets and prices have turned yesterday's economic reserves into today's waste, hopefully to be converted into economic ore again in some distant time. One way of replenishing reserves and maintaining a viable mining industry is to find and develop mines which are economic under short-term depressed price and market conditions. This probably means higher grades. A new copper discovery with the right combination of characteristics to be an attractive investment even at today's pices for copper would still merit development into production. Exploration is the only way to find such mines for the difficult short-term conditions. Another important consideration is that normally many years stretch from the first thought of conducting exploration to production -- in those rare instances where an economic discovery is made. If discoveries are not made today, then there will not be any projects to develop when business conditions are more attrative. This industry and the vast number of skilled professionals who are part of mining, are faced with two key problems that underlie the need for a junior exploration segment. One consideration is how to maintain exploration during those years, indeed eras, of recession and depression. We are in such a time now. Throughout the world, major companies have sharply cut back, if not eliminated completely, exploration expenditures other than what is vitally necessary and easily and inexpensively done at the known and producing deposits. And related to that consideration, even more important today than during happier times, is how to finance such necessary ongoing exploration if major companies and governments back away because of financial stringency. CANADIAN SUCCESS In Canada, such problems are being tackled with a success which is capturing worldwide attention. The ability of mineral explorers to obtain willing, eager, high-risk capital is achieving even more outstanding results than in the past. These results are reflected in the widespread continuing exploration ativity in Canada which even spreads into the United States, with some outstanding discovery successes. The most notable exploration success from junior mining activity is the discovery of the Hemlo gold camp in northwestern Ontario, a source of gold which promises to rank with the South

Jan 1, 1985

By O. J. C. Runnalls, L. M. Pidgeon

Some observations on the kinetics of the iodide process are reported. The deposition rate is geometry-sensitive in a system containing a finely divided titanium charge. Further, results indicate that the iodine diffusion rate influences the velocity of the process. The nonvolatile iodide, Til,, forms in the hot filament zone, thus removing iodine from the cycle. TITANIUM metal of 99.9 pct purity may be prepared using a refining technique originated by Van Arkel and de Boer.' The purity of this metal, commonly called iodide titanium, exceeds that produced by any known process. In a recent application, the method was employed by Gonser et al.² to prepare titanium rods up to 2 to 3 cm in diam. In the Van Arkel-de Boer system, the relative influence of the fundamental mechanisms: l—production of titanium iodides, 2—gaseous countercurrent diffusion, and 3—decomposition, on the deposition rate have not been clearly established. Blocher and Campbell" have indicated that the controlling step in the process under practical conditions of operation may be the reaction rate of iodine with the crude metal. Fast' reported that crude titanium metal reacted with iodine rapidly, even at room temperature, in his apparatus. Little has been reported on the effect of gaseous diffusion or decomposition on the deposition rate. It is these aspects of the process about which this investigation is centered. An attempt has been made to separate these latter effects from those due to the formation of the iodides at the crude metal surface by a division of the experimental program. Reaction of Iodine with Titanium Apparatus: In the investigation of gas-metal reactions of this type, the chemical reactivity of the halogen and halide vapors dictates the use of all-glass apparatus. In such a system standard techniques for measuring reaction rates are difficult to employ. Here, a simple apparatus was devised (Fig. 1) so that some indication of the reactivity of titanium powder with iodine vapor could be obtained. A stream of iodine gas was evolved from a bulb of controlled temperature and passed over a sample of titanium powder heated in a horizontal tube furnace. The product of the reaction, TiI4, volatilized and was condensed outside the furnace in a series of four glass bulbs, each cooled to room temperature in turn. Preliminary experiments indicated that distillation was retarded in a sealed evacuated system due to a pressure build-up in the condensing end of the apparatus. Hence, the system was pumped continuously using a mechanical pump and two oil diffusion pumps in series, through a liquid air trap. The iodine bulb was made large and a capillary restriction was inserted between the titanium bulb and the condensers so that the iodine pressure over the metal would approach the equilibrium pressure over solid iodine crystals. The effect of this restriction on the evaporation rate of TiI4, was determined separately. The iodine bulb was heated in an oil bath controlled to ±2°C. The titanium bulb temperature was automatically controlled to ±5°C. Procedure: About 200 mg of —30 mesh titanium powder, weighed to 0.1 mg, was placed in the reaction bulb after part B had been joined to part A. The powder was tapped into a long (5 cm) shallow mass along the bottom of the tube. Two chromel-alumel thermocouples were inserted into the magnesium radiator which was clamped to the reaction

Jan 1, 1953

S. Tandanand, Twin Cities Mining Research Center, U. S. Bureau of Mines As an addition to the fine reviews on drilling presented in the foregoing papers, we feel it would be appropriate to mention briefly some work in this area by the U. S. Bureau of Mines. The Bureau has had under way for several years at its Twin Cities Mining Research Center studies directed toward a better understanding of basic drilling mechanisms. The work includes drillability investigations with diamond rotary, and with percussive drilling systems, as well as fundamental studies of rock behavior under drill bit types of loading. Results of our work to date have contributed the following to the state of the art. MECHANISM OF ROCK FAILURE-Rock fragmentation through use of mechanical energy systems, including drilling systems, consists of two major components-machine and rock. The two components are related to each other by their functional behavior and their resultant motion which the components mutually influence. Forces in the systems are transmitted directly to the bit which in turn induces stresses in the rock. When the induced stresses exceed the strength of the rock, the rock fails resulting in penetration. Rock strength is a function of the forces applied to the rock. Stresses under a drill bit, regardless of bit configurations, are essentially compressive, resulting in a condition where the rock has the highest resistance to failure. The ratio of principal stresses induced under drill bits is an indication of the mode of failure in the rocks. Initially, compressive stresses under the drill bit cause rock to undergo inelastic deformation. The impression observed at the first stage of crater formation under the drill bit shows that rock is no longer elastic. Associated subsurface failure at this stage precedes total rupture which subsequently appears at the rock surface. Thus, explanation of crater formation, by applying theory of elasticity alone, is likely to be over-simplified. ENERGY VERSUS VOLUME OF ROCK REMOVED-Experimental results show that energy per unit volume of rock removed is constant for a particular rock and bit type. Rock offers a definite resistance to penetration, depending on the method of the energy application; this may be defined as the drilling strength of a rock. Energy consumption in a drilling system may be divided into two components: 1) Energy required to move the machine parts; and 2) energy consumption in breaking rock. Component 1 is dependent on the type of the machine. Component 2 is dependent on the strength properties of rock and the efficiency of the bit in rock cutting. The sum of the energy required in both components determines the total energy required in breaking rock. Our work in this area has included consideration of both diamond and percussive drilling systems. PENETRATION RATE-For a drilling rate expression to be useful in predicting field performance, it should include the operating characteristics of the drilling machine. Eq. 37, for example, is simply a statement of the fact that the drilling rate is determined by the power output of the machine (2pNT) and the power requirements to break the rock in the hole (AER). In order to predict the performance of a particular drill and the effect, for example, of the rotary speed, on the drilling rate, R, Eq. 37 must be modified to include the

Jan 1, 1967

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.' Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.' The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company's mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By A. F. Crawley

The densities of some liquid Pb-Sb alloys up to 11 wt pct Sb and Pb-Sb-& alloys up to 10 pct Sb/10 pct Sh have been determined by a pycnometric technique over a temperature range of about 130°C above their melting points. The data given are accurate within 0.05 pct. Density is shown to vary linearly with temperature , and equations relating these quantities have been formulated. Molar volumes calculated from the density data indicate that volumetric deviations from ideal mixing are undetectable within the limits of experimental error. A continuing research program into some fundamental physical properties of liquid metals is being pursued at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This work has received support from the Canadian Zinc and Lead Research Committee in cooperation with the International Lead and Zinc Research Organization. This paper, which reports some density data for Pb-Sb and Pb-Sb-Sn alloys, follows previous work from this laboratory on lead, tin, and Pb-Sn alloys.' Of previous data from others, Greenaway2 and Sato and Munakata3 have reported results on Pb-Sb alloys. No previous work has been published on the ternary Pb-Sb-Sn alloys, reported here. EXPERIMENTAL METHOD Densities were measured by a pycnometric technique which has been described in detail and appraised for accuracy in earlier Mines Branch reports.475 Fig. 1 shows the densitometer with the pycnometer in position for a run. The pycnometer is also shown in some detail. The pycnometer of dense, high-purity graphite, about 14 cu cm in volume, was carefully machined to a uniform, smooth finish. The height was measured by a depth micrometer and the diameter by fitting precision gage blocks between steel balls.' In each case several readings were taken, and the final results were considered accurate within 0.01 pct. The resulting volumetric uncertainty together with small inaccuracies in the coefficients of linear expansion of graphite lead to a maximum systematic uncertainty in the method of ±0.03 pct. As shown in Fig. 1, the pycnometer lid is a threaded cap. Thus, the charge, a cylinder of the alloy, can easily be inserted and the solidified metal can readily be removed after a run. The dimensions of the cylindrical charge are chosen to ensure that, once molten, the metal will not only fill the pycnometer completely but will discharge an excess into the excess-metal float chamber. AS the temperature is increased above the melting point, the volume of metal in the excess chamber increases until the system has equilibrated at the desired temperature. At this point, the excess chamber is moved to one side by twisting the shaft F, leaving a fixed volume of liquid metal in the pycnometer. This volume of fluid is readily calculated using measured coefficients of linear expansion of the graphite which expands anisotropically. The associated weight of fluid is determined as the weight of the solidified metal removed after the furnace has cooled down. Alloys were prepared from 99.997 pct Pb, 99.999 pct Sn, and 99.999 pct Sb, being melted by an electric furnace in a graphite crucible and poured into graphite molds. Several density specimens of the same nominal size were machined from each ingot, and, by comparing specimen weights, relative differences in specimen composition resulting from segregation in the ingots could be detected. In this way, segregation was found to have occurred in Pb-Sb alloys at compositions beyond the eutectic (11.2 pct Sb) and this

Jan 1, 1969

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953