Search Documents

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

By R. H. Eckhouse, M. R. Geer, H. F. Yancey, C. L. Allyn

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By W. J. Kroll

W. J. Kroll (Belgium)—Those who are acquainted with the metallurgy of our forefathers may have occasionally a good time when glancing at recent publications in which aged discoveries are unconsciously reported as novelties. We know very well, that oxygen blowing of iron has been described by old Bessemer. The author of the present article is, however, not aware of the fact that the process he describes, the fused salts scrubbing, was already used in the middle of the last century by St. Claire Deville in his attempts at making higher-purity aluminum from raw AlCl3 by sodium reduction. The same fact escaped the three investigators to whom the author refers. The technical grade AlC13 produced by St. Claire Deville from impure oxide, chlorine, and carbon (Oersted process) was contaminated with Sic4 and FeC13, which he removed on an industrial scale by various methods.' He sublimed, for instance, his chloride in contact with iron nails, or aluminum chips, or in hydrogen, which reduced the FeC13 to the less volatile FeCl2. He used also alkali-alkaline earth chlorides as a solvent for A1C13 and FeC13 in presence of iron as a reducing agent, and sublimed his purified AlC13 from solvent salts. The successors of Deville used also zinc or lead as a reducing agent. These methods were later used currently for the purification of BeCl2 and for collecting this compound in a salt bath, suitable for fusion electrolysis. More recently, the same Deville process has been described as applied to the purification of ZrCL4, as part of a method of extraction of ZrCL4 from silico zirconium, which later was reacted with FeC12 in a separate part of the equipment. According to the patent referred to3 the ZrCL4 is dissolved as a gas in a carrier salt such as alkali-alkaline earth chloride, from which it can be reclaimed in a purified form by distillation. A bath of NaCl/KCl is recommended in the specifications. The FeC12-FeC13 go in the salt solution in which raw ZrCl4 is introduced by bubbling, while Sic4 and Tic4 pass through the bath and escape in the atmosphere. purification by this salt-solvent method is thus well described. It may be worth while insisting on some minor details about which the author did not bother too much. One of these concerns the material of construction for the container. If iron is used, and if no other reducing agent is added, then it is the iron of the pot that acts as a reagent in the breakdown of FeC13 to FeCl2, and corrosion can be expected. This shows the importance of using extraneous large surface-reducing agents, of which there is a choice. Zir-

Jan 1, 1963

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

The Candelaria deposit was first discovered by Spanish prospectors in 1863; but its silver ore was not exploited on a large scale until 1873, when the Northern Belle mine was opened. The first Northern Belle mill was built at Belleville, 13 km (8 miles) to the northwest. From 1876 to 1886 the Northern Belle paid over $1 million in dividends each year. In 1882 a 43 km (27 miles) pipeline was built to Candelaria from the White Mountains to the west to furnish water for the mills and town at Candelaria; it was 100 mm (4 in.) in diameter, hand- riveted, and made in England. Sections of this pipe are used. as claim posts today. At its terminus at Metallic City, above Candelaria, a large concrete reservoir was built and called Metallic Lake. It is being used today by Candelaria Partners. Production at Candelaria declined after the mid-1980s, revived for a short period in the early 1890s, and during the 1920s a 300 ton mill operated for three years. Candelaria Partners is owned jointly by Occidental Minerals and Congdon and Carey, with Occidental being the operator. An engineering study done in mid-1979 resulted in engineering for the plant commencing in late that year and heap leaching being started in September 1980. Two million tons of ore per year containing 108 g Ag and 0.28 g Au per mt (3.15 oz Ag and 0.008 oz Au per st) will be mined from the Lucky Hill and Mount Diablo .areas about 1.6 km (1 mile) up Pickhandle gulch from the heap leaching operation. Waste -to -ore ratio is about 2:l. Ore is mined by front-end loaders and hauled by 85 ton trucks to the primary crusher, a 1,070 by 1,780 mm (42 by 70 in. ) gyratory. Primary crushed ore is conveyed to a stockpile of 10,000 tons live capacity from which it is reclaimed by hydraulic reciprocating feeders and conveyed to the crushing and agglomeration facility. This unit is composed of a 1.8 m by 2.6. m (6 ft by 12 ft) double deck screen, a 2.1 m (7 ft) standard cone crusher, and three conveyors. At the conveyor transfer points NaOH and NaCN solution is sprayed on the ore as it falls through a row of 75 mm (3 in.) hanging steel bars. During this process of turning and dividing the ore, the fines agglomerate with the coarse ore to give better percolation for the leach solution on the heaps. Provision was made for the later addition of 2 kg per mt (4 lb per st) of cement to aid in the agglomeration. Agglomerated ore at minus 50 mm (2 in.) size is then conveyed to a 390 mt (430 st) loadout bin where it is transferred to 85 ton rear dump trucks for haulage to the leach pads.

Jan 1, 1981

By O. J. C. Runnalls, L. M. Pidgeon

J. M. Blocher, Jr. and I. E. Campbell (Battelle Memorial Institute, Columbus, Ohio)—Since the de Boer-Van Arkel process for making titanium metal involves a number of steps in a fairly compact unit, it is difficult to determine simply which of the steps is rate controlling. In any statement as to which step constitutes the rate-controlling process, qualifications appear to be in order. It is possible to design a reaction bulb in which any one of a number of steps is made to be controlling. I—With the filament removed some distance from the crude, as in the case of the authors' experiments, the interdiffusion of iodine and iodide may be controlling. 2—If, as is usually done, the crude metal is placed in a perforated cylindrical basket, or as a briquetted mass, in close proximity to the filament, the rate of deposition is increased (we obtained rates of deposition 5 to 10 times those cited in the authors' paper), and another rate-limiting factor, such as the reactivity of the crude, may take over. In this regard, we have noticed radically different rates of deposition with different crudes, and with crudes in various stages of exhaustion. 3—With a very reactive crude metal and with optimum practical geometry, still another process may be controlling. It is felt that this is a diffusion process in the immediate vicinity of the filament involving the fundamentally adverse situation of a net flow of particles away from the filament. The separate experiments on the reactivity of iodine with titanium are interesting but somewhat inconclusive. Data is still needed on the partial pressure of iodine in an operating decomposition bulb. A knowledge of the gradient of iodine partial pressure from the crude to the filament would be particularly enlightening. Optical absorption may be a useful technique here. Accurate measurements of the total pressure within a decomposition bulb under various conditions would be quite revealing. Preliminary measurements have been made at Battelle in following this line of attack. It is interesting to note that the authors' data on the temperature dependence of deposition rate indicate that the overall rate is not controlled by the kinetics of the decomposition reaction at the filament: TiI1 ? Ti + 4I Any reasonable estimate of the activation energy of this reaction would, if its kinetics were controlling, dictate a much greater temperature dependence than is observed here. The authors apparently attribute the drop in deposition rate (eventually to zero) with increased TiI4 pressure solely to a decrease in diffusion rate. However, there is an equilibrium factor involved here that must not be overlooked. As the partial pressure of TiI4 is increased, a point is reached where, due to the competing reaction of the tetraiodide with titanium to form lower iodides, the equilibrium partial pressure of titanium is reduced to the point that it equals the vapor pressure of titanium at the filament temperature and the deposition rate falls to zero. This effect would

Jan 1, 1953

By H. C. Chao, Y. E. Smith, L. H. Van Vlack

ThE phase relationships for the MnO-MnS system have been investigated only in the eutectic region. wentrupl reported a eutectic at 1280°C (2345°F) with approximately 50 wt pct of each component, as based on the earlier work of Andrew, Maddocks, and Fowler.2 More recently silverman3 corrected these figures to 2275° ±10°F (1246°C) with 63 wt pct MnS and 37 pct MnO. Neither Wentrup nor Silverman investigated the solid-solution limits in this system. However, Wentrup did suggest with his phase diagram sketch that the maximum solubility of MnS in MnO is 10 wt pct, and the solubility of MnO in MnS is nearer 20 wt pct, Fig. 1. These figures have been utilized in subsequent publications without further verification.4 There had been evidence found in this laboratory that the above solid-solution figures were high. An investigation was therefore conducted using the following procedure. Samples containing MnO and MnS were contained in platinum foil, heated just above the eutectic temperature in a purified nitrogen at- mosphere, and quenched into distilled water. The MnO had been prepared by calcining reagent grade MnCO3 in nitrogen at 1400°C. Only MnO was detected in subsequent X-ray diffraction analyses. The MnS had been prepared by sulfur deoxidation of reagent grade MnSO4 according to the reaction: MnSO4 + S2 ? MnS + 2SO2 The details of the sulfide preparation procedure, which utilized atmospheric sulfur pressures at 950°C, are discussed elsewhere.5 The sulfur content of the sulfide was determined to be 36.8 * 0.2 pct, which matches the stoichiometric value of 36.9 pct. No evidence of either MnO or MnSO4 was detected microscopically or by X-ray diffraction. The single-phase combinations of MnO and MnS at the eutectic temperature indicate the limit of solid solution as shown in Fig. 2(a) and (c), and the revised phase diagram is shown in Fig. 2(d). The melting temperature for MnO is that provided by Glasser.6 The eutectic temperature of 1232° ± 5°C and eutectic composition of 64 wt pct MnS are in close agreement with Silverman's correction of Wentrup's work. The maximum solubility of MnO in MnS was determined to be 1.7 ± 0.2 wt pct. The maximum solubility of MnS in MnO was determined to be 1.8 ± 0.2 wt pct. These figures represent the lower limit for the presence of liquid at 1260°C and are significantly lower than the earlier estimated solid-solution figures. The authors wish to acknowledge the support of U.S. Steel's Edgar C. Bain Laboratory for Fundamental Research. The comments and critical suggestions of Drs. A. S. Keh, R. Rickett, and R. B. Snow are appreciated.

Jan 1, 1963

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation' yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.' In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors' personal experience has shown that

Jan 1, 1957

By W. R. Aufricht, E. H. Koepf

The theory, measurement, and application of capillary forces in reservoir rock have been treated ex-tensively in the various petroleum publications.1,2,3,4 These forces are of prime importance in oil production, and data on capillary properties are among the most important tools used in the study of reservoir mechanics. The principal application of measured capillary pressure data by the production and reservoir engineer is in the determination of the initial distribution and mobility of fluids in the reservoir. The distribution refers to the magnitude of the oil and interstitial water saturations under capillary equilibrium conditions and to their variation throughout the reservoir as a result of changes in rock properties and nearness to free water. The magnitude of the water (or oil) saturation, as well as the porosity, is required in volumetric calculations of oil in place. In low permeability reservoirs, where long transition zones are common, the magnitude of the oil content, even below the depth interval where commercial rates of flow of oil can be obtained, must be evaluated since this oil contains energy available to the production of the remainder of the reservoir. The mobility of the water phase is of particular importance in water-flood calculations since mobile water may condemn what would otherwise be a successful water flood. In reservoirs with predominantly small pores, high immobile water contents are possible. Conversely, reservoirs with predominantly large pores may contain mobile water even though the interstitial water contents are relatively low. This presentation reviews the distribution and mobility of interstitial water contents as determined from capillary pressure data and shows typical data for various types of carbonate reservoirs. A discussion of the variations found in different types of carbonate reservoirs is given. DISCUSSION Interpretation of Laboratory Data Fig. 1 is a typical laboratory capillary Pressure curve where water saturation as Per cent of Pore space is plotted vs capillary Pressure (psig) for an air-water system. This par- ticular curve was obtained by measurement on a sample of San Andres dolomite with intergranular-type porosity. The sample studied had a permeability of 10.0 md and a porosity of 18.8 per cent. The capillary pressure-saturation relationship illustrated is an inherent property of the rock (a function of the size and distribution of the pores) and represents the ability of this water-wet rock to retain water against the pressure differential exerted by a non-wetting fluid (oil or gas) to remove it. In the laboratory a known pressure differential is exerted from a pressure source; in the reservoir the pressure differential is controlled by the density difference between the hvdrocarbons and the water. The laboratory capillary pressure values may be converted into terms of equivalent height of water column using known values of reservoir oil and water density and measured or average values of interfacial tension

Jan 1, 1958

By Pierre I. Desré, Donald T. Hawkins, Ralph Hultgren

The torsion effusion method has been used to measure the vapor pressure of thallium over pure thallium in the temperature range 931" to 996'k The resulting 100 cal per g-atom is in excellent agreement with previous values. Vapor pressures of T1 above seven Ag-Tl alloys ranging from 33 to 90 at. pct T1 were measured at 979K. Calculated silver activities show a positive deviation from Raoult's law, approaching ideality near the liquidus. Measured thallium activities scatter less than previous measurements using the electromotive force technique. Values for the silver component were calculated by Gibbs-Duhem integration. This paper reports the results of a study of the liquid Ag-T1 system by the torsion effusion method. The method has been discussed in detail previously1 and will be only briefly summarized here. The sample is contained in a cell which is suspended on a torsion wire. Vapors effusing from orifices on opposite sides of the cell exert a torque on the wire. The torque is related to the vapor pressure by the following relation: where D is the torsion constant of the wire, 4 the angle of torque, fl and f2 the correction factors determined by Freeman and seamy2 to account for orifice length, a1 and a2 the areas of the orifices, and ql and q2 the distances of the orifices from the axis of rotation. By using the same cell for pure thallium and the alloy, it follows that: so that most systematic errors are eliminated in determining the activities. EXPERIMENTAL 99.999+ pct T1 was obtained from the American Smelting and Refining Co. and 99.999 pct Ag was obtained from Cominco American, Inc. Seven Ag-T1 alloys, ranging in composition from x^\ = 0.33 to 0.90, were prepared by melting together weighed amounts of the pure metals in sealed, evacuated Vycor tubes and quenching the melts in water. The apparatus and graphite cells were the same as those used by Hawkins and Hultgren3 in their study of the Pb-Sn system. RESULTS Ten measurements were made on pure thallium in the temperature range 931" to 996K, and the results are presented in Table I. Values of were calculated using tabulated Gibbs (free) energy functions.4 No dependence of on temperature or orifice size was found, indicating that equilibrium was attained. Data for the Ag-T1 alloys are shown in Table 11. Values were smoothed with respect to composition by a plot of where . DISCUSSION The value = 43,520 * 100 cal per g-atom for pure thallium (95 pct uncertainty limit) is in excellent agreement with previous investigations.4 In the Ag-T1 system, this study shows positive deviations from Raoult's law at all compositions. Fig. l gives the phase diagram according to Hansen, and Fig. 2 presents the activity values measured in this study as well as those from electromotive force measurements at 950°K by Terpilowski, Kundys, and slaby.'

Jan 1, 1969

By B. D. Lichter

The lattice parameters of zirconium and zirconium-oxygen solid solutions (hcp) were determined from measurements of back-reflection X-ray photograms obtained at 29°C using a symmetrical focussing camera. The following linear equations between parameters (c,a) in angstrom units (10-8 cm) and atom ratio (m) of oxygen to zirconium were obtained: c = 5.14764 + 0.2077m a =3.23168 + 0.1099m. The linear equations given are valid over the range 0 to 5 at. Pct 0. The accuracy of individual parameter measurements approaches the limiting accuracy determined by the spectral broadening of the incident characteristic radiation, and exceeds the accuracy of previously reported values. THE present work was undertaken in order to determine the lattice parameters of zirconium-oxygen solid solutions with an accuracy that allows quantitative determination of oxygen in zirconium. The results indicate that this is possible if very careful measurements are made, since the parameter change is only a few hundredths of a percent per at. pct 0.1, 2 In the present investigation the desired accuracy was achieved with large-grained samples using a back-reflection focussing camera and maintaining good temperature control during exposure. In addition a digital computer was used for calculation of the parameters by means of an analytical extrapolation.37 Suitable diffraction photograms were obtained from large-grained samples by using a modification of the technique described by Graf and Monteil.5 This consists of simultaneous rotation and oscillation of the specimen about two mutually perpendicular axes during exposure. Whereas, normally the upper limit of grain size is about 50 µ for useable diffraction photograms, this technique allows extending the upper limit of grain-size to exposure of a single crystal. EXPERIMENTAL Preparation of Alloys for X-ray Diffraction—Zir-conium, designated as hafnium-free, Westinghouse "Grade 1," was swaged from l/2-in.-diam crystal bar to 3/8-in.-diam rods. Substantially all of the hydrogen was removed from the zirconium by annealing at 1200°C in a high dynamic vacuum. The rods were then swaged to 0.2 in. diam without intermediate annealing, and 2 in. lengths were cut for alloying with oxygen. Samples for chemical analysis were taken from portions of the rods between each 2 in. length. Chemical analysis of the dehydroge-nated zirconium is given in Table I. Commercial tank oxygen (99.5 pct 0) was condensed in a liquid nitrogen-cooled trap, and part of the condensate was slowly reevaporated into 5-liter storage flasks. Nitrogen remained as a reactive impurity, and the calculated maximum increase in nitrogen content after a 5 at. pct 0 addition to zirconium was 50 ppm by weight. However, chemical analyses of several of the prepared alloys indicated that the maximum increase in nitrogen content was 10 ppm. The storage flasks, a Sieverts-type gas burette and manometer, and associated traps, pumps, and pressure gauges were connected through a glass high-vacuum manifold to comprise the gas addition system. A fused silica tube, connected to the mani-

Jan 1, 1961

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

The Lornex mine is located in the Highland Valley area of British Columbia, Canada, one of the most,promising districts of low-grade porphyry-type copper mineralization in the world; Lornex is operated by Rio Algom Mines, Limited, a member of the Rio Tinto Zinc Group of London. Exploration from 1965 to 1968 disclosed an ore body of 293 million tons with a grade of 0.43% copper and 0. 14% molybdenum; this led to the decision to construct a 38,000 tpd operation, and production commenced in the fall of 1972. The ore is open-pit mined with 15 cu yd (11 5 m3 shovels, which load 100- and 200 -ton trucks. These trucks dump directly into a 60 in. by 89 in. Allis -Chalmers gyratory from two sides of the 14 ft 6 in. (4.42 m) deep dump pocket and across splitters mounted on the pocket sides. The unlined pocket would hold 1,000 tons level full. The crushedore discharges into a 300-ton surge hopper equipped with an automatic sonic level indicator to prevent over -filling. A 96 in. by 23 ft (2.44 m by 7 m) apron feeder delivers the ore from the surge hopper to a 72 in. (1.83 m) transfer belt equipped with a tramp iron metal detector. The transfer belt discharges to a 60 in. (1. 52 m) conveyor which conveys the ore about 3,000 ft (914 m) to the 475,000 ton ore storage pile located near the concentrator. Four 48 in. (1.22 m) pan feeders transfer the ore to the mill feed conveyors, which in turn supply the two 32 ft by 15 ft (9. 75 m by 4. 57 m) semi-autogenous mills, which easily accept the 10 in. (254 mm) product of the crusher. Each semi- autogenous mill is followed by a secondary ball mill. The unusually large open side setting of the crusher accounts for its 6,300 tph maximum capacity. Concentrator capacity is now 48,000 tpd. Eccentric removal is eased by the design of the door to the crushed ore pocket, which has the cart rails mounted on its outer surface and is lowered to a horizontal position in the pocket by an electric winch. The top of the door rests on wear bar covered concrete piers in the pocket. Another feature is a chute through the floor at the crusher base that extends into the crushed ore pocket. Dust and spills of ore on that floor during crusher repairs are easily swept into the crushed ore pocket. This feature is also used at Bougainville and Palabora and has been added to others after operation has commenced. The design follows the concrete rectangular box concept with four main service and maintenance levels shown in the sectional drawings, although a third additional section has been added at the maintenance

Jan 1, 1978

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By C. F. Seaman, R. G. Clay

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By G. A. Vissac

IN the presentation which follows, washability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. FLOAT-AND-SINK TESTS For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve "-a somewhat misleading term-will be considered. Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. NEW FORM OF GRAPHIC PRESENTATION The resemblance of the recovery curve in Fig. I, or, for that matter, the recovery curve obtained in common practice, to a power curve is apparent. The general equation of such a curve is y = axn where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis, the recovery graph will be a straight line, using the same variables as in Fig. I ; namely, the ash con-

Jan 1, 1942

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949