Search Documents

By A. L. Holley

THE occurrence of this gas, in quite appreciable. quantities, has been observed for many years in its escape along the creeks of Western Pennsylvania, and more recently, in much larger quantities, from the oil wells in and near Venango County. Within about five years several gas wells have been struck, from which the gas has escaped continuously in prodigious quantities and at great pressure. During the last year a systematic attempt has been made to utilize the flow of gas from one of these wells, and results have been reached which were quite unexpected. This well, near Leechburg, Armstrong County, is about twenty miles northeast of Pittsburgh, on one of the side tributaries of the Alleghany River. It had been drilled in search of oil to a depth of 1250 feet in 1871, but none was found. A great flow of gas was developed, however, accompanied by a slight spray of salt water, and this has continued with little or no diminution to the present time. The gas in its escape has been discharged through a 5-inch pipe, and at a pressure of from 60 to 80 lbs. per square inch, but no exact determinations, either of the pressure or quantity, have been made. The rolling mill of Messrs. Rogers & Burchfield is on the opposite side of the river, and it has been for some years devoted to the production of fine grades of sheet iron from charcoal pig metal, by puddling and in knobbling fires. The usual weekly product of the mill has been 30 tons of No. 30 tin plates, and 50 tons of No. 24 to 28 sheets. The well was bought by this firm for $1000, and the gas is led across the river, a distance of about 500 feet, through a 3-inch pipe. It is distributed through half-inch pipes, and at a pressure of about 45 lbs. per square inch, to several of the furnaces, but a large fraction of the total flow of gas is still wasted at the well. No essential alteration in any of the furnaces has been found necessary in the use of the gas fuel, except to brick up the fire-bridge and to put in the gas and air pipes. The old grate used for coal is loosely covered with bricks and cinder, so that a slight percolation of air may take place through them. The gas is admitted through a half-inch pipe, and blows toward the fire-bridge through 18 or 20 one-eighth inch jets. The air is blown in at about 2 lbs. a

Jan 1, 1876

By A. L. Holley

The occurrence of this gas, in quite appreciable quantities, has been observed for many years in its escape along the creeks of Western Pennsylvania, and more recently, in much larger quantities, from the oil wells in and near Venango County. Within about five years several gas wells have been struck, from which the gas has escaped continuously in prodigious quantities and at great pressure. During the last year a systematic attempt has been made to utilize the flow of gas from one of these wells, and results have been reached which were quite unexpected. This well, near Leechburg, Armstrong County, is about twenty miles northeast of Pittsburgh, on one of the side tributaries of the Alleghany River. It had been drilled in search of oil to a depth of 1250 feet in 1871, but none was found. A great flow of gas was developed, however, accompanied by a slight spray of salt water, and this has continued with little or no diminution to the present time. The gas in its escape has been discharged through a 5-inch pipe, and at a pressure of from 60 to 80 Ibs. per square inch, but no exact determinations, either of the pressure or quantity, have been made. The rolling mill of Messrs. Rogers & Burchfield is on the opposite side of the river, and it has been for some years devoted to the production of fine grades of sheet iron from charcoal pig metal, by puddling and in knobbling fires. The usual weekly product of the mill has been 30 tons of No. 30 tin plates, and 50 tons of No. 24 to 28 sheets. The well was bought by this firm for $1000, and the gas is led across the river, a distance of about 500 feet, through a 3-inch pipe. It is distributed through half-inch pipes, and at a pressure of about 45 Ibs. per square inch, to several of the furnaces, but a large fraction of the total flow of gas is still wasted at the well. No essential alteration in any of the furnaces has been found necessary in the use of the gas fuel, except to brick up the firebridge and to put in the gas and air pipes. The old grate used for coal is loosely covered with bricks and cinder, so that a slight percolation of air may take place through them. The gas is admitted through a half-inch pipe, and blows toward the fire-bridge through 18 or 20 one-eighth inch jets. The air is blown in at about 2 lbs.

ROBERT PEELE, New York, N. Y. (written discussion *).-This excellent paper is one of a number of recent detailed descriptions of the, methods and plant in use at prominent mines of the country. The publication of such papers cannot be too highly praised. In the past, the interchange of inside information has often been hampered by the disinclination of some mining companies to permit publication of details of their work. These companies apparently have not realized fully that free discussion is of mutual benefit; that members of mine staffs are aided in. keeping up to date, in improving old methods and devising new ones to meet changes in conditions, and, by a wholesome feeling of rivalry, are stimulated to introduce economies and do better work. In writing this paper, Messrs. Haight and Tillson have packed a large amount of information into a relatively small space, and the numerous illustrations, chiefly reductions of working drawings, are valuable. The authors are also to be commended for their highly detailed Table of Contents, which adds to the usefulness of the, subject matter. The method of mining at Franklin does not fall readily into any of the accepted classifications. It is a combination of shrinkage stoping and mining of the pillars by a modified top-slicing method. Attention may be called to the fact that, in the wider parts of the orebody, the stopes, 17 to 18 ft. (5.2 to 5.5 m.) wide are transverse; in the narrower parts, they are longitudinal, that is, in the direction of the' strike. This varia-tion is made necessary by the shape and character of the deposit, and distinguishes practice at Franklin from that in some of the western mines. The direction of the stops is changed from transverse to longitudinal when the orebody narrows sufficiently to make the length of a transverse stope approximately equal to its width. Some of the longitudinal stopes exceed 120 ft. (36 m.) in length, and when the hanging wall is bad, requiring prompt filling, three operations' proceed simul-taneously in the same stope, viz., ore is broken at one end, while drawing down goes on in the middle, and filling at the other end. Each transverse stope or chamber is begun by a crosscut from foot to hanging wall, which is afterward enlarged to the stone width and to a height of 12 or 15 ft. (3.7 or 4.6 m.). This preliminary work is done only once for each stope, because the stope is carried up far enough to continue stoping

Jan 1, 1918

By T. Sterry Hunt

It is now five years since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field; and to show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had shown that this coal could be used with advantage in iron-smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal seam, and I then ventured to express the opinion that this region, from its cheap and easily mined smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to state how far my observations made in the region 1st month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all' it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964

By Carl G. Hogberg

DURING recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. PRINCIPLES OF IRON DESULPHURIZATION IN FURNACE Although investigations of the blast-furnace process have not clearly revealed the detailed mechanism of iron desulphurization within the furnace, they have been sufficiently extensive to permit a postulation of the following general principles: I. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurization is relatively narrow, being confined to a vertical distance extending approximately from tuyere level to the iron-slag interface in the hearth.1 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.2 Coke ash is released as the coke burns in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

John A. Church, New York City: It requires some courage to appear as a critic of a theory which is not only the fashion among American geologists but is usually presented by them in terms which imply that any other views are an exhibition of ignorance. Still, I am obliged to say that the theory of lateral secretion as it is stated in this and other writings of Mr. Emmons and other geologists has not added much to our real knowledge or clearness of view. In the earlier and less developed stages of the theory, when it was used as Sandberger used it, to show that certain veins were probably derived from the rocks in which they lie, or which are adjacent, it was valuable in pointing us to an immediate source of ore-deposition. When we are driven to assume the existence of undiscoverable rocks at an unknown but certainly a considerable distance and in an unknown direction from the vein, I do not see that we have improved upon the despised " unknown source in depth " with which our ignorance has been covered so long. The new theory may suffer from adolescence, and these points map be cleared up by further study, but I speak of it as it is. Differentiation in a magma, by which a metal is concentrated in one member of a series of outflows, may explain why certain ores have favored a given locality with their presence; but it is not a necessary precedent to ore-formation. Concentration in the source of supply cannot be a requirement, for the forces that have been able to take up four or five tons of gold from an extensive body of rock must be able to collect four or five thousand tons of lead, copper or nickel from a proportionately more extended body of rock. That is to say, concentration is no more essential for these metals than it is for gold. In fact, differentiation, as it is now explained, is not an advance upon old ideas, but a retreat from them. It was noticed long ago that violent eruptive phenomena, however long continued, died away in solfataras; and when a vein came to be looked upon as an extinct solfatara the inference was ready that veins are eruptive in the sense that the solfataric waters collected the metals from the unerupted residue of the magma and carried them to the veins. The early views carried differentiation further than the modern school.

Jan 1, 1894

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By L. S. Reid, R. L. Huntington, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By A. E. Back, W. Wyman, K. E. Tame, S. F. Ravitz

In 1940, when it appeared that the United States soon might be cut off from foreign sources of high-grade manganese ore, the Bureau of Mines began an extensive series of investigations on the production of ferro-grade products from low-grade domestic ores by ore-dressing, pyrometal-lurgical, and hydrometallurgical methods. Among the hydrometallurgical processes for oxide ores investigated was a sulphur dioxide process in which the manganese was recovered from solution by precipitation with lime;' this process is essentially as follows: The ground ore is suspended in water and leached with SO2 gas to extract the manganese as manganese sulphate. Calcium chloride is then added to the slurry to precipitate calcium sulphate and form manganous chloride solution, and the resultant slurry is filtered to remove the calcium sulphate together with the insoluble portion of the ore. Calcium hydroxide is added to the filtrate and the mixture is agitated with air to precipitate hydrated oxides of manganese and regenerate calcium chloride. The precipitate is calcined, and the calcium chloride is recycled. To determine manganese extraction, reagent consumption, grade of product, and similar data for this process, a labora- tory investigation was started. Two minor modifications in the process were soon made: (I) the ore was suspended in calcium chloride solution instead of in water in order to extract the manganese and precipitate the calcium sulphate in one step, and (2) the agitation with air after the addition of slaked lime to the filtrate was omitted because manganese hydroxide is readily precipitated without air agitation and can be nodulized or sintered to a satisfactory product. When the process was carried through a series of cyclic tests, it was noted that the concentration of dithionate ion (which is one of the products of oxidation of SO2 by MnO2) in the cycled solution gradually increased; at the same time the chloride content of the solution gradually decreased, owing to soluble losses in the leach residue and in the precipitate. After a number of cycles, the calcium chloride became virtually completely replaced by calcium dithionate, the quantity of dithionate ion formed during the leach being more than enough to make up for the losses of dithionate in filtering. The calcium chloride process thus developed into a calcium dithionate process. Since the latter eliminated the need for make-up calcium chloride, and the dithionate solutions appeared much less corrosive than the chloride solutions, work on the calcium chloride process was dropped in favor of the calcium dithionate process. Acknowledgments The dithionate process was developed by the Bureau of Mines as part of a

Jan 1, 1949

By R. L. Huntington, L. S. Reid, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By Charles S. Barrett, F. W. Steadman

DEFORMATION bands of surprising regularity are found in large-grained polycrystalline copper after cold-rolling (Fig. I). Individual bands frequently are large enough to permit a determination of their orientation by means of etch pits and an optical goniometer. Measurements have been made on 21 areas in seven different grains, and these, combined with X-ray studies of nine single crystals that had been cold-rolled after mounting in a polycrystal-line block, have contributed to a better understanding of the preferred orientations in rolled copper just as similar studies have for rolled iron' and brass.2.3 Particular attention was given to determining orientations that are stable during rolling and to the manner of fragmentation and rotation of unstable grains. The possible role of twinning was also carefully investigated. The texture of polycrystalline copper after cold-rolling is well established by the pole figures that have been plotted by Schmid and Staffelbach,4 Iweronowa and Schdanow,5 and Brick and Williamson,3 all of which are in substantial agreement. There has been some divergence in the list of individual "ideal" orientations that have been used to describe the texture by these observers and others,6 although the orientation (110) [112]-that is, (110) parallel to the rolling plane and [112] parallel to the rolling direction-is generally recognized as the most prominent orientation and (I12) [111] one of the lesser orientations. Other orientations have been given by some observers as (236) [533], (100) [001], and (I 10) [001]. The texture of copper has also been described as (135) [533].6.1 The sum of these orientations provides a reasonable approximation to the complete pole figure, but it does not follow that these specific orientations are necessarily of fundamental significance, for the choice of indices is arbitrary, within limits. Furthermore, a detailed investigation of the ideal orientations in cold-rolled iron discloses continuous ranges of equally favored positions rather than definite positions of high stability,1 and similarly Brick's observations in a single crystal of a brass2 suggest that all orientations in the range between (110) [113] and (110) [117] are about equally stable. MATERIALS AND METHODS The material used was vacuum-cast electrolytic copper kindly supplied by L. L. Wyman, of the General Electric Co.* Slices 1/2 in. thick and 2 1/2 in. square, cut from the ingot, were rolled with 50 per cent reduction per pass to final thicknesses between 0.02 and 0.04 in., and etched to develop cube-face etch pits suitable for goniometric work.8 The etch was light on some strips and deep in others.

Jan 1, 1942

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By Gerald Edmunds

In a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the , origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical changc in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained—i.e., (001) parallel, ± 2oo, to the surface—as was obtained when it was cast against air, Transite or iron.' Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about 1/4 in. of lead, then 1/2 in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 136 in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,' with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two 1/4-in. diameter aluminum-alloy die-cast tensile bars and on a 1/8 by 1/2-in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. Summary A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. Acknowledgment The X-ray determinations were conducted by M. L. Fuller.

Jan 1, 1945

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By E. DeGoyler

The Furbero oil field lies in the Gulf coastal plain of Mexico between the important ports of Tampico and Vera Cruz and about one-third of the distance between the two points from the latter (Lat. 20" 22' N., 97" 30' W. Gren.). It is in the State of Vera Cruz, about 14 miles west by south of the village of Papantla in the canton of the same name, and is the most southern of the developed oil fields of the Tampico-Tuxpam region being a distance of 50 miles south by east from the Potrero del Llano field and 42 miles in the same direction from the Alamo field. The field has been developed by the Oil Fields of Mexico Co. and is in the midst of a large block of lands owned or leased by them. Communication is through the port of Tuxpam with which it is connected by a narrow-gauge railway and 6-in. pipe line some 52 miles in length. This field is of more than ordinary interest since it represents a type of oil deposit hitherto unknown. So far as I am aware, no other commercially valuable deposit of oil is known to occur under conditions of accumulation similar to those found here. The igneous nature of the so-called 'sand' encountered in drilling was not recognized until a number of wells had been drilled; and it was not until recently that the geological relations of the sill or laccolith, which gives rise to the accumulation of oil, were known and the so-called 'anticline' was known to be, in part at least, the result of igneous intrusion. Geological surveys in this general region were made in 1900-1901 by W. H. Dalton and in 1907-1909 by P. C. A. Stewart, F. W. Moon, Leonard V. Dalton, and Dr. Max Muhlberg. More recent surveys have been made, however, under the direction of the author, by E. L. Ickes, B. C. Belt, B. Hartley, and Harve Loomis. Notes of the earlier examinations were not available with the exception of the report by Dr. Muhlberg who apparently first recognized the true nature of the Furbero intrusion. This paper is indebted to his work and that of the more recent surveys for much of the detail regarding stratigraphy and to Messrs. Percy Furber and Arthur C. Payne, President and General Manager of the Oil Fields of Mexico Go. for permission to publish, and for much of the in-

Jan 1, 1916

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors' knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat'"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law's method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

By F. W. Steadman, Charles S. Barrett

Deformation bands of surprising regularity are found in large-grained poly-crystalline copper after cold-rolling (Fig. I). Individual bands frequently are large enough to permit a determination of their orientation by means of etch pits and an optical goniometer. Measurements have been made on 21 areas in seven different grains, and these, combined with X-ray studies of nine single crystals that had been cold-rolled after mounting in a polycrystal-line block, have contributed to a better understanding of the preferred orientations in rolled copper just as similar studies have for rolled iron1 and brass.2,3 Particular attention was given to determining orientations that are stable during rolling and to the manner of fragmentation and rotation of unstable grains. The possible role of twinning was also carefully investigated. The texture of polycrystalline copper after cold-rolling is well established by the pole figures that have been plotted by Schmid and Staffelbach,4 Iweronowa and Schdanow,6 and Brick and Williamson,8 all of which are in substantial agreement. There has been some divergence in the list of individual "ideal" orientations that have been used to describe the texture by these observers and others," although the orientation (110) [II2]—that is, (110) parallel to the rolling plane and [TIP] parallel to the rolling direction—is generally recognized as the most prominent orientation and (112) [III] one of the lesser orientations. Other orientations have been given by some observers as (236) [535], (100) [00I], and (110) [00I]. The texture of copper has also been described as (I35) [533].6,7 The sum of these orientations provides a reasonable approximation to the complete pole figure, but it does not follow that these specific orientations are necessarily of fundamental significance, for the choice of indices is arbitrary, within limits. Furthermore, a detailed investigation of the ideal orientations in cold-rolled iron discloses continuous ranges of equally favored positions rather than definite positions of high stability,' and similarly Brick's observations in a single crystal of a brass2 suggest that all orientations in the range between (110) [II3] and (110) [II7] are about equally stable. Materials and Methods The material used was vacuum-cast electrolytic copper kindly supplied by L. L. Wyman, of the General Electric Co.* Slicec 1/2 in. thick and 21/2 in. square, cut from the ingot, were rolled with 50 per cent reduction per pass to final thicknesses between 0.02 and 0.04 in., and etched to develop cube-face etch pits suitable for goniometric work.8 The etch was light on some strips and deep in others.

Jan 1, 1942