Search Documents

By R. Kossowsky

BRIDGMAN has listed five possible transitions in bismuth at 25°C which were observed as volume changes. He was unable however to detect the last three transitions by electrical-resistivity changes. Kennedy and LaMori have verified the pressures at the Bi 1-11 and Bi 11-111 transitions. They suggested however that the 125-kbar transition previously reported by Bundy3 actually corresponds to the 90,000 kg per sq cm transition observed by Bridgman.1 Jura4 reported a well-defined drop in resistivity at 92 kbar obtained by a four-lead method. The Bi 111-IV and Bi IV-V transitions have not been reported in any of the above-mentioned references.'-' Bundy3 observed a small dent in the low-temperature boundary of the Bi Vll region which is consistent with the presence of a 111-IV boundary. Zeitlin and Bray-man5 were the only ones to report small but well-defined drops in resistance of bismuth at 44.0 and 63.8 kbar, corresponding to Bridgman's 111-IV and IV-V transitions, respectively. High-purity (99.99 pct) 0.020-in.-diam 0.5-in.-long bismuth wire was used to calibrate the Uniram tetra-hedral high-pressure apparatus used in the present work. The bismuth phase changes at 25°C were correlated with changes in electrical resistance as a function of pressure. The output of a sensitive bridge constructed of carbon resistors and kept at a constant temperature of ±°C during the measurements was fed to the Y axis of a MoseleyX-Y recorder and the X axis was used for time scans. Specimens were pressurized using a hydraulic press with maximum capacity of 200,000 lb. Load was applied in increments of 2000 lb and held for about 3 min. The resistance was recorded at the end of this time period. Good contact was established below 20,000 lb. Typical recorder charts are reproduced in Figs. 1 and 2 which show that resistance fluctuations were practically nil during each time scan. Well-defined discontinuities in resistance were observed at 58,000 and 82,000 lb, Fig. 1. Two small but definite "blips" are noticed at 92,000 and 122,000 lb, Fig. 2. At 156,000 lb another drop is observed which

Jan 1, 1967

By A. W. Allen

The technological study of the treatment of gold and silver ores has been largely responsible for the phenomenal strides which have marked the progress in this branch of metallurgy during recent years. In no other application of science to industry is system more imperative at every stage; correct formulation of result is only second in importance to efficiency of operation. Progress in method, on the other hand, is mainly due to individua1 initiative aided by the work of technical journals and metallurgical societies. There still remains a field for profitable discussion, and it is my intention to deal with some inconsistencies of expression common to a number of writers on the subject; and also to draw attention to the false impressions created by a statement which may, possibly, be only unintentionally misleading. I also take the opportunity of tracing the source of both metallurgical and economic result; and would question the desirability of the methods usually employed in arriving at a final statement. In the first place, I wish to deal with the question of extraction. This term may mean anything or nothing, and it is often used to mislead. In a report of a mining engineer as to the result of operations subsequent to the remodeling of a treatment plant prominence was given to the statement that the extraction had amounted to 91 per cent. On examination it was found that only a small percentage of the so-called extraction was calculated on actual bullion return, a proportion being figured from the gold left in the zinc boxes, and not recovered. In addition to this, a proportion of the extraction was said to be due to gold in concentrate. As there was no conrcentrating apparatus on the property and as concentration did not form a part of the scheme of treatment the matter was investigated, with the result that the concentrate, of lower gold content that the original ore, was found to be the result of an inegcient pumping system which failed to provide for the whole of the battery product delivered to it. The balance was stacked and, although itself of no marketable value, the gold content was allowed to form a basis of extraction figures. The illustration may be extreme, but it will serve to show to what lengths an engineer may go in the mutilation of the most vital term in metallurgical technology.

Jan 1, 1915

THE great subject of interest in American affairs during February was the consideration of the proposed soldier bonus. This proposal was based upon the idea that, because most of the workers of the United States had enjoyed high wages during war, the soldiers were entitled to "adjusted compensa-tion" in order to equalize things. It overlooked the fact that the soldiers, themselves, had the opportunity to enjoy high wages in 1919 and 1920, when rates were highest. Apart from this, the whole project was founded on fallacies and involved what would be nothing less than economic crime. Although it looked as if the measure were destined to be railroaded through Congress, so great a storm of protest was pelted upon Congress that the present outlook is that the whole project will be abandoned. There was probably some increase in the physical volume of business during February. A rise in prices for agricultural products assisted the farmers mate-rially. These developments, however, are not to be construed as presaging any general upward movement. On the contrary, the current year is to be contem-plated as one of serious labor troubles, following inevit-able reductions of wages. These began in February in the form of an extensive strike in the cotton textile industry of New England, accompanied by some rioting in Rhode Island. The coal miners have had numerous conferences, without coming to any encouraging results, and the stage appears to be fully set for a general strike beginning Apr. 1. About the only question now is whether this will comprise both the bituminous and anthracite miners. If the latter refuse to go out, no serious shortage of coal is anticipated, the belief being that the existing stocks together with the output of the non-union mines will supply the demand, which is sub-normal even now. In the metal industries, lead and zinc were dull but stable. The weakening tendency in iron and steel that was manifest during January appeared to be checked, at least temporarily. Copper was charac-terized by a distinct weakness and a considerable decline in the market. This downward movement was inspired by the news during January that several of the important mining companies were taking steps to resume production. During February the demand for copper, both foreign and domestic, was poor.

Jan 3, 1922

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963

By P. G. Winchell, R. J. Russell

The distribution of displacements of originally plane surfaces by an invariant-plane strain has been analyzed statistically. The displacement ratio (the magnitude of the displacement of a point originally a unit distance from the invariant plane) can be determined from an analysis either of tilts of random surfaces or of displacements of random scratches scribed on a randowz surface. In either case the mean of the tangent of the observed displacement angle is related to the displacement ratio, and the number of observations used in determining the mean is related to the confidence limits placed on the estimate of the displacement ratio. In estimating the effect of applied stress on a phase transformation whose displacement effects can be approximated as an invariant-plane strain,* the dis- placement ratio of the invariant-plane strain is of primary importance. Two procedures for determining such displacement ratios are considered here. In the tilt method the measured quantity is taken to be the angle through which a random polish plane is rotated by the invariant-plane strain. In the scratch method the measured quantity is taken to be the angle between the original direction of a random scratch in a random polish plane and the projection of its final direction in the polish plane. In order to obtain precise results from either of the methods, it is necessary to measure the relative volume change associated with the strain in a separate experiment. TILT METHOD A locally homogeneous invariant-plane strain, P, with displacement ratio, S, may be written&apos; where ; and < are unit vectors indicating the displacement direction and invariant-plane normal, respectively, as pictured in Fig. 1. Eq. [I] describes a uniaxial strain if the direction of displacement is parallel to the invariant-plane normal and a pure shear strain if the displacement direction is perpendicular to the invariant-plane normal. The original orientation of the random polish plane relative to the invariant plane and to the displacement direction is shown in Fig. 2. The angle 03 between < and u is related to the relative volume change, ?V/V, and to the displacement ratio by As a result of the invariant-plane strain, the polish plane is rotated about its intersection with the invariant plane by the angle y, which is always taken to be positive. The tangent of this angle in terms of the above parameters is

Jan 1, 1967

By R. A. Meussner, R. J. Goode

Six intermediate phases occur in the Nb-Zn sysThese phases form by peritectic reactions at 1120°, spectively. The Nb Zn 15 phase appears as the minor phase in the eutectic structure, and the terminal phases remain nearly pure niobium and zinc even at high temperature. Vapor -pressure measurements on the four high-temperature phases (Nb Zn to Nb Zn 3) permitted estimates of the composition limits of these phases and the calculation of approximate values of AFO, AH°, and AS°. 1 HE present study of the constitution of the binary Nb-Zn system was a part of an analysis of the mechanism by which coatings of the Nb-Zn intermediate phases protect niobium against oxidation at high temperature.&apos; Since the primary interest in these phases was in coating service, attention in this study was given principally to the four phases stable at high temperature with only cursory attention to the two low-temperature phases. The solubility studies of niobium in zinc by Martin, Knighton, and Feder2 and the reports from the present study of the Nb-Zn coating represent the only published data pertaining to this system. Previously Hodge, Evans, and Hoskins, in an experimental survey, had noted that niobium was not resistant to attack by molten zinc, but no further observations were reported. EXPERIMENTAL PROCEDURES a) General. The nature of the binary Nb-Zn system precluded the use of more conventional methods of determining the phase equilibria such as thermal analyses of a series of cast alloys. An extrapolation of the liquidus data of Martin, Knighton, and Feder2 to higher temperatures suggested that the solubility of niobium in zinc would remain low in the entire temperature range of interest. The preliminary results of the present studies showed that all of the high-temperature intermediate phases form by peritectic reactions. Thus the sluggish nature of this type of reaction and the steepness of the liquidus indicated that thermal analyses would not yield reliable data. The peritectic reactions, of course, precluded the direct formation of samples of the individual phases from the melt. b) Materials. The niobium and zinc used in the present studies were of high purity. The niobium, in the form of 0.1-in.-diameter rods, contained 30 ppm 0, 30 ppm N, and 15 ppm C. Aside from 0.05 pct Ta, the metallic impurities (iron, titanium,

Jan 1, 1965

By G. W. Crane

When ore was discovered on the Tintic Standard property in the spring of 1916, new developments were immediately started both north and south of that property, on the supposition that in East Tintic the ore would be found to occur in northerly trending channels, similar to those so characteristic of the older camp. But 9 years of developments have failed to establish the existence of such a channel. This is due undoubtedly to important differences in the geology of the two camps, that were not recognized, and is indicative of the danger in the general tendency toward interpreting the geology of East Tintic too strictly in terms of that of the older camp. It should not be forgotten that while the two sections have had practically the same geological history, the net results of a long series of geologic processes have developed in them conditions that differ so widely and in so many particulars that the necessity of regarding them as essentially different districts seems apparent. In an effort to emphasize this fact, this paper is devoted chiefly to a comparison of the geological conditions as found in the two camps and is addressed more particularly to those familiar with the geology of the Tintic district. Following a short description of the several ore discoveries and of the Tintic Standard mine is a brief discussion of the evidence of ore channels in East Tintic. For my information regarding the Tintic Standard mine, I am indebted to the courtesy and generous assistance of Messrs. Wade and Snow of the Tintic Standard Mining Co. East Tintic District The Term East Tintic district is here used to represent that eastern part of the Tintic mining district lying between the productive portion of the old camp of Tintic on the west, the foot hills of Goshen Slope, on the east, the Denver and Rio Grande Railroad on the north, and Silver Pass on the south, all in Utah County. As represented by the geological map, Fig. 1, it includes an area about 4 miles wide, east and west, and 5 miles long, north and south, within which the Tintic Standard mine is about centrally located. The map is a compilation of data supplied, for the most part, by the Chief Consolidated Mining Co. and represents the

Jan 1, 1927

By E. W. Mehal, R. W. Haisty, D. W. Show

The next generation of integrated circuits will probably include circuits constructed in and of GaAs. The existence of both semi-insulating and semiconducting forms of GaAs is the fact which will bring this about. In this paper we discuss the uses and limitations of semi-insulating GaAs for integrated-circuit applications. The two main areas considered are the electrical isolation that can be achieved between components on a semi-insulating substrate and the characteristics of p-n junctions in contact with semi-insulating GclAs. A process basic to attaining integrated circuits in GaAs to fully utilize the insulating properties of the substrate is selective epitaxial deposition. This process involves the deposition of a SiO2 layer onto a The trend in integrated circuits is towards the use of high-resistivity substrates or regions to achieve component isolation. The use of SiO, layers in the oxide isolation methods and the use of sapphire substrates are examples of this idea. GaAs is also a polished surface of a GaAs substrate, etching out selected area of the SiO, film to expose a GaAs surface, and deposition only onto the exposed GaAs surface. By using this process , islands of semiconducting GaAs are deposited onto a semi-insulating GnAs substrate, the islands being electrically isolated from one another by the substrate. The deposition of both p- and n-type semiconducting GaAs can be carried out in this nzanner to form p-n junctions in the island areas. This process can also be used to produce a planav structure by deposition of GctAs through a SiO, mask into holes etched into the GaAs substrate. This Putterned Epitaxial Technology (PET) is described. very promising material for use in future integrated circuits because of the existence of both semi-in-sulating and semiconducting forms. Active devices can be fabricated in the semiconducting material, and these individual components can then be electrically isolated from one another by using semi-insulating GaAs as the substrate. Epitaxial semi-insulating GaAs can also be produced thus making three-dimensional monolithic integrated circuits feasible.&apos; This paper describes the research aimed at developing the methods for producing both two- and three-dimensional integrated circuits in GaAs, and examines some of the properties of semi-insulating GaAs as they relate to these integrated circuits.

Jan 1, 1967

By P. W. George, G. A. Hellstrand

In 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-Newfoundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicating about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereof, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company&apos;s metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company&apos;s testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1935

By John H. Hollomon

THE interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,1 Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this DaDer of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the 1920&apos;s. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic de- formation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently MC- Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze&apos;s (and RlcAdam&apos;s) analysis of the stresses (which have been pointed out by SachsI6) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers17-l8 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By H. H. Power, Charles R. Houssiere

THE development of effective and dependable methods for drilling through the so-called "heaving-shale" horizons, particularly in the Gulf Coast area, is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Many mechanical remedies have been proposed and are in use in troublesome areas for combating heaving shale. However, in conducting a research program it was concluded that the physical and chemical properties of shales should be investigated, and the effect of added chemicals on such properties determined. As a preliminary step, the effect of chemicals on bentonitic suspensions was determined in accordance with recent contributions in the field of ceramics. The most plausible theoretical explanations for the behavior of the clay minerals involved are offered in the paper that follows. It is hoped that subsequent investigation of actual shale from troublesome wells will be aided by the initial work done on bentonitic suspensions of known composition. INTRODUCTION Formations variously designated as "heaving shale," "sloughing shale" and "caving shale" impede and may even preclude drilling of oil wells, particularly in certain parts of the Gulf Coast. In a previous paper1 it has been stated that the development of effective and dependable methods for drilling through these troublesome beds is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Since the attack on the heaving-shale problem by mechanical means was principally a matter of field investigation, it was concluded that a research program should be concerned with the physical and chemical properties of heaving shales, and the effect of added chemicals on such properties. It was realized that a study of shales required an advanced knowledge of the behavior of the individual clay minerals. A thorough review of the literature led the authors to the conclusion that very recent contributions2.3 in the field of ceramics furnished the most plausible theoretical explanations for the behavior of clay minerals. Accordingly, these fundamental ideas will be used in an attempt to explain the behavior of more complex systems whose composition and replaceable ions are known. In order to obtain comparable results it was deemed important to select an easily procurable clay of uniform characteristics. Accordingly, Wyoming bentonite, which is marketed under the name of "Volclay,"* was used for the preliminary investigations. The chemical analysis reported by the distribution is given as follows:

Jan 1, 1941

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the &apos;economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40&apos; above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Ulick R. Evans

I Should like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country—researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. Films Produced at Elevated Temperatures If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Leo J. Vogel, E. D. Hummer

INTRODUCTION by E. D. HUMMER An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contributes to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and operating costs of the plant, but greatly affects the design of the refuse disposal system. The design of a mine and plant should include the location and the estimated capacity of the disposal areas for the life of the property or plant. Complete evaluation of the disposal system and an estimate of its annual cost of operation over the life of the property or plant should be incorporated in the plant and mine evaluation. Plant design should be as simple as possible, consistent with the efficient production of clean coal. Material transfer points, crushing, screening and pumping operations should be kept to a minimum to reduce degradation and the subsequent increased difficulty and cost of refuse removal. The maintenance of good process control by operating management will result in a minimum of misplaced material in both refuse and clean coal. Reduction of misplaced float material in the plant refuse is an important factor in preventing combustion in the refuse storage pile. THE REFUSE DISPOSAL AREA Combustion in refuse piles occurs when air enters the pile in sufficient quantity to support oxidation. At certain rates of air in-filtration, the heat produced by the oxidation process is not dissipated and temperature rises.

Jan 1, 1968

By Ulick R. Evans

I Should like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country—researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. Films Produced at Elevated Temperatures If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,&apos; Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o&apos;s. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze&apos;s (and McAdam&apos;s) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco&apos;s largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days&apos; travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,&apos; Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o&apos;s. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze&apos;s (and McAdam&apos;s) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica&apos; reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica&apos;s knots was quickly confirmed by Guinier&apos;s&apos; and preston&apos;s3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs&apos; in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 36 tons of water for each ton of coal produced, while bituminous mines average about 5 or 6 tons. Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. But it must also be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1973