Search Documents

By C. E. Meissner

The need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. Furnace Design There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the check-ers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped unti1, the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace. The slag pockets and checkers are cleaned by digging down to arched openings which have been bricked up.

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By C. W. Davis, R. S. Dean

The purification of iron ores by means of hand magnets dates back more than 100 years. The first record in the United States Patent Office of a machine for the magnetic separation of ores shows that on Feb. 20, 1849, U.S. Patent 6121 was issued to Ransom Cook for improvement in electromagnetic ore separators. The patent covered the use of a revolving cylinder, or drum, with poles of electromagnets in its periphery for the purpose of separating magnetic oxide of iron from substances with which it might be associated, by causing the electrornagnets when revolving as component parts of the cylinder to be successively charged to take up the ore and discharged to part with it. Since this patent was issued the science and technique of magnetism have advanced more than most other fields of endeavor. The development of electrical machinery has required and obtained better and better magnetic materials, and the science of applied magnetism is as completely and satisfactorily developed as any branch of physics. Nevertheless, the patent of Ransom Cook, issued in 1849, comes close to covering everything that is now being applied in magnetic separation. The cynic may conclude that this proves the uselessness of modern science and may point in confirmation to flotation, which has grown in a few years, practically without benefit of science, to be the most versatile and useful of concentration methods. On more careful study, however, it appears that an accurate determination of the magnetic properties of minerals and their amenability to control by mechanical and heat treatments has not heretofore been made. The first essential, therefore, in the design of improved magnetic separators has been missing. In spite of this hiatus in scientific data inventors have been busy, and patents are on file covering mineral separations by means of nearly all known magneto-mechanical effects. Because of a lack of knowledge of mineral properties, most of these inventions never worked well enough to find commercial use. The Metallurgical Division

Jan 1, 1935

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) IN the case of The Eureka Consolidated Mining Company v. The Richmond Mining Company of Nevada, recently tried at San Francisco, California, the real defendant was the Richmond Consolidated Mining Company, of London; but this being a foreign corporation, holds its mining property in Nevada through the Nevada corporation of similar name, in which the London Company owns all the stock, except the few shares necessary to "qualify" the American directors. The trial would naturally have taken place in the Circuit Court at Carson City, Nevada, and before a jury. But by stipulation of the parties, the case was tried in San Francisco, before Hon. Stephen J. Field, Justice of the Supreme Court of the United States, Hon. Lorenzo Sawyer, United States Circuit Judge of the Ninth Circuit, and Hon. E. W. Hillyer, United States District Judge, for the District of Nevada. The hearing began July 23d, 1877. The witnesses occupied two weeks, and the argument of. counsel three days. Very eminent lawyers were. engaged on both sides ; for the plaintiff, Messrs. Solomon Heydenfeldt, R. S. Mesick, John Garber, and H. J. Thornton ; for the defendant, Messrs. S. M. Wilson, Thomas Wren, and J. J. Williams. The court held the case under advisement until August 22d, when Mr. Justice Field delivered its unanimous opinion in favor of the plaintiff. The action was a complaint in ejectment, and an appeal was taken to the United States Supreme Court. The questions at issue between the Eureka and the Richmond Company in this suit, comprised several points in the construction of the mining law of the United States, and its relation to the customs and regulations of the mining districts, which possess an importance and an applicability far beyond the limits of the case in which they arose. It is my purpose to state these points, the arguments

Jan 1, 1878

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf' seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.'"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By Clarence E. Jackson, George G. Luther

The ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepaxed with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. 2, the angle at maximum load in lour cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By D. A. Keyes

International Minerals & Chemical Corp. (Canada) Ltd. is presently exploiting by underground mining a potash-rich zone in the middle Devonian Prairie Evaporite formation near Esterhazy, Saskatchewan. Of the three main potash-bearing horizons denoted by Goudie as zones 1, 2 and 3 only the 1ower. two are present at Esterhazy and mining is confined to the lower or zone 1 horizon. The area in which the evaporites were deposited, although flanked on the west by a zone of geosynclinal deposition and tectonic activity, has been subjected to only very gentle epeirogenic activity. The sylvinite ore is coarsely crystalline and occurs in well-defined beds. The halite, sylvite and insoluble content of the ore bears a direct relationship to the lithological units, but the carnallite cuts across the beds. Local concentrations of salt produce blank spots in the ore horizon. Some of these appear to be salt-filled, post-ore channels and cracks while others have been formed by brines emanating upward from below the ore. INTRODUCTION International Minerals & Chemical Corporation (Canada) Ltd. is operating an underground potash mine near the town of Esterhazy in eastern Saskatchewan. The deposit was discovered by IMC in 1955. Subsequent drilling outlined extensive high-grade reserves, and in 1957 shaft sinking and plant construction began. Production from Yarbo No. 1 Shaft commenced in September, 1962 and quickly reached the initial capacity of one million tons of muriate product per year. Production is currently being expanded to 1.6 million tpy. The single mining level is 3140 ft below the surface at No. 1 Shaft. GENERAL GEOLOGY The Esterhazy district lies within the Interior Plains region of Canada and on the northeast rim of the Williston Basin (Fig. 1). Average dip of the rock formations in this area is about 40 ft per mile to the southwest. The potash ore occurs in the Prairie Evaporite formation of the Middle-Devonian Elk Point Group. The Prairie Evaporites are overlain by 3000 ft of Paleozoic shales and limestones and by Jurassic and Cretaceous sandstones and shales (Fig. 2).

Jan 1, 1967

By S. L. Hoyt

Some of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc. Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is due, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. Classification of Materials According to Toughness Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may be deformed plastically, but only by the expenditure of considerable energy. In other words, tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is comparatively rapid, as in impact testing, but in all cases the stress distribution is essentially uniform. However, static toughness does not

Jan 1, 1920

By Chester T. Sims, Robert I. Jaffee

The thermoelectric behavior of the Pt—Pt-Re thermocouple and the resistance of rhenium to attack by certain molten metals is discussed. In addition, data are presented on the stress-rupture behavior of drawn wire, the tensile characteristics of rolled sheet, the variation of Young's modulus with temperature, and the effect of specimen size and fabrication method on the work harden ability. Mechanical properties of thoriated rhenium are discussed. This includes data on the effect of thoria in rhenium on tensile properties, ductility, work hardening, and recrystallization. RECENT work by the authors', has described methods of fabrication and some of the physical and mechanical properties of rhenium. Rhenium was established as a high melting, dense, refractory-type metal with favorable mechanical properties. In addition, Todd and co-workers' and others" have studied such properties of rhenium as the work function, specific heat, and the resistance of rhenium to the water cycle. Revelation of these and other properties has led to serious consideration for application as electrical contacts, high temperature thermocouples, and wear resistant materials. chanical properties reported previously,' several additional examinations have been conducted. The stress-rupture behavior and the Young's modulus of rhenium have been investigated at elevated temperatures. Tensile data have been obtained for rolled sheet, and a study of the relative work hardening characteristics of rod, wire, and sheet has been conducted. Variation of Modulus of Elasticity With Temperature—The Young's modulus of a % in. diam annealed rhenium rod was determined from room temperature to 880"C (1620OF). The rod, approximately 6 in. in length, was activated in a transverse vibration apparatus suspended in a furnace. The resonance frequencies of the rod were measured and used to calculate the moduli values. The driven frequency was 569 cycles per sec, and a protective helium atmosphere was used. The data, plotted in Fig. 1, show that the modulus decreases in an approximately linear manner with temperature over the range tested.

Jan 1, 1957

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington Counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ounulgee and Oconee Rivers drain the area. They and their main tributaries have flat, swampy flood plains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirquelike heads. Gullying and undercutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig 1. The division between the Coastal Plain and the Piedmont Plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward- sloping surface of the crystalline rocks of the Piedmont.

Jan 1, 1952

By T. R. Graham, R. G. Feustel, J. R. Long, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By L. A. Delano

DURING 1916, the St. Joseph Lead Co. milled 2,505,670 tons of ore. This is a daily operating average of 7855 tons. The economic concentration of such a large tonnage necessarily requires a plant equipped with modern machinery and operated efficiently. The milling process used in producing this output has been a gradual development through the long period of years that the company has been in existence. HISTORICAL SUMMARY OF MILLING PRACTICE Ore was first mined at Bonne Terre, Mo., in 1864. The early milling practice was crude. It consisted of breaking the ore into small pieces by hand, pulverizing in a Blake crusher and a pair of Cornish rolls to approximately minus 6 mm., and jigging in the old-fashioned hand jigs. Only the coarse heavy galena was saved, the gangue being shoveled off and discarded. The output for the first year under this method was only 240 tons of pig lead. The first mill of the company was a combination of extensions and additions built from time to time as the mines developed. It was a museum of early mulling machinery, such as jigs, percussion tables, huddles, dolly tubs, log washers, etc., following no definite flow sheet. The chats, or tailings, were hauled to waste dumps by mule and ox teams, as much as 500 tons per day being moved in this manner, until a railroad was built in 1880. This mill was burned in 1883, at which time the annual output had reached approximately 7300 tons of pig lead. A new mill of 500 tons capacity was designed and built by C. B. Parsons. This mill has been admirably described by H. S. Monroe.1 The ore was crushed in Blake crushers, Cornish rolls, through 6-mm. screens, and treated by jigs of the Parsons type, percussion tables and log washers, or trunking machines, for cleaning the galena. The middlings were recrushed in rolls and treated on Harz jigs. The mill was operated without change, except later installing Gates crushers and en-

Jan 9, 1917

By L. A. Delano

During 1916, the St. Joseph Lead Co. milled 2,505,670 tons of ore. This is a daily operating average of 7855 tons. The economic concentration of such a large tonnage necessarily requires a plant equipped with modern machinery and operated efficiently. The milling process used in producing this output has been a gradual development through the long period of years that the company has been in existence. HISTORICAL SUMMARY OF MILLING PRACTICE Ore was first mined at Bonne Terre, Mo., in 1864. The early milling practice was crude. It consisted of breaking the ore into small pieces by hand, pulverizing in a Blake crusher and a pair of Cornish rolls to approximately minus 6 mm., and jigging in the old-fashioned hand jigs. Only the coarse heavy galena was saved, the gangue being shoveled off and discarded. The output for the first year under this method was only 240 tons of pig lead. The first mill of the company was a combination of extensions and additions built from time to time as the mines developed. It was a museum of early milling machinery, such as jigs, percussion tables, buddies, dolly tubs, log washers, etc., following no definite flow sheet. The chats, or tailings, were hauled to waste dumps by mule and ox teams, as much as 500 tons per day being moved in this manner, until a railroad was built in 1880. This mill was burned in 1883, at which time the annual output had reached approximately 7300 tons of pig lead. A new mill of 500 tons capacity was designed and built by C. B. Parsons. This mill has been admirably described by H. S. Munroe.' The ore was crushed in Blake crushers, Cornish rolls, through 6-mm. screens, and treated by jigs of the Parsons type, percussion tables and log washers, or trunking machines, for cleaning the galena. The middlings were recrushed in rolls and treated on Harz jigs. The mill was operated without change, except later installing Gates crushers and en-

Jan 1, 1918

By Charles Burgess

THE improvement, in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in. connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. MATERIAL TESTED Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two -series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing - 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250° C. (2282° F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, 'the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown In Table 1, test 2. A small amount of copper was present in heat C of this series.

Jan 1, 1932