Search Documents

By Benjamin S. Lindsey, James Norman

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942

By J. G. Tilton

While most of the Pittsburgh coal horizon is dependably regular, there are areas where it is dis-turbed by sandstone cutouts which can seriously hamper mining operations. Because these channel sandstones often cut out the coal abruptly, they are difficult to detect by core drilling; and mine operators, for want of a better way to discover them, have largely trusted to luck to avoid them. This paper, based on a study the author is presently conducting, is an attempt to point out some sources of information and signposts which might aid the operator in determining the presence of a cutout before he begins to mine. The presence of sandstone cutouts in the Pittsburgh coal has been known for many years. Some of these irregularities were observed at outcrops and others were discovered by drilling, but the majority were and are found during mining operations. These sandstone cutouts are commonly called "faults" and have been a bane to mining companies wherever they have been encountered. Profiles of some typical deposits appear in Fig. 1. The cutouts disrupt the normal system of mining, replace valuable coal reserves, create ventilation problems by emitting large quantities of gas and sometimes oil, limit the number of entries that can be economically driven, affect the quality of the coal, disrupt the normal structure of the coal, and create roof control problems. It might be expected that such severe disturbances in the structural regularity of the coal would instigate determined and extensive searches for possible cutouts prior to mining operations, but this apparently has not been so except in isolated cases. Two reasons may be cited to explain this lack of exploratory work. The first and probably the strongest reason is the over-all regularity of the Pittsburgh coal. No coal seam in the country exhibits the horizontal continuity and relative regularity of the Pittsburgh coal. It lies in an almost unbroken sheet across southwestern Pennsylvania, eastern Ohio and northern West Virginia, and has been recognized as far east as the Potomac Basin of western Maryland. Over 5729 square miles are underlain by this coal, of which 2077 square miles are in Pennsylvania, 2214 square miles in West Virginia, 1410 square miles in Ohio, and 28 square miles in Maryland. The area covered by this study is outlined by the map in Fig. 2. Over most of this territory the coal has the following characteristic structure as illustrated in Fig. 3: roof coal, draw slate, breast coal, parting, bearing in coal, parting, brick coal, parting, and bottom coal. With such regularity of thickness and structure, mines were opened and laid out with confidence that the coal would be present. Extensive drill testing was considered unwarranted and it was also quite expensive because the coal dipped to the west away from the Monongahela River. Consequently, drill holes were widely spaced and rarely encountered ad-

Jan 1, 1968

By L. E. Young

LOADING machines may be classified in several ways: (1) Machines which cut or break down and load .the coal; (2) machines which simply load the coal; (3) devices which load and transport the coal; (4) de-vices which elevate; (5) devices which transport the coal after it has been shoveled onto the device. There are many types of mechanical loading devices, Bull. 17, Coal Mining Investigations, under the auspices of Carnegie Institute' of Technology, U. S. Bureau of Mines, and the Advisory Board, listing 31 exclusive. of -the large shovels used in thick coal seams. Mechanical loading of coal is not in its infancy; I think some of the early patents go back to 1890. One large coal company, properly called the early leader in this field of mechani-zation, has about 26 large machines at work. This company spent about thirty years in developing a ma-chine, and at the present time is loading approximately two million tons of coal a year in its mines. The chair-man directed a question at the previous speaker; inquir-ing if real progress was being made in mechanical load-ing. The experience of the company just referred to is in itself an adequate answer. A review of a list of mines using mechanical loading devices shows that there are 28 mines which we may say are 100 per cent mechanical. There are four more mines which have been 100 per cent mechanical, but which are idle at this time on account of labor condi-tions. There are at least 25 more at which the tonnage is more than 50 per cent mechanical. In speaking of a 100 per cent mine I do not mean that every pit car of coal is loaded by machine, because when complete, re-covery of the coal is attempted it is not practical to load all the coal at, the break line. In order to load the last 5 to 10 per cent of coal with a minimum of gob material and in order to keep the. working places along the break line timbered in a safe manner it is generally desirable to use a few hand loaders. At a certain mine operat-ing on the block system 90 percent of the coal is being loaded by what is properly a mechanical loading: device, and about 10 per cent -is being loaded by hand. This 10 percent is right off the break line, out of what might be called, the screen pillar. The mines referred to are scattered over the country, . in seven different' States, and the equipment used is produced by ten different machinery companies. As to size, these mines vary from small mines of 500 tons mining capacity-up. In one instance a company with one loading machine is producing an, average of 450 tons per day. One of the large mines that is idle pro-duced at the. rate of 4300 tons per day, of which 97 per cent was actually loaded by machinery.

Jan 8, 1928

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R203. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder ,was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By D. B. Robinson, J. Lukacs

A knowledge of the equilibrium water content of hydrocarbon systems under pressure is important to the natural gas industry. The information available on the solubility of water in hydrocarbon, hydrogen sulfide, and carbon dioxide systems is reviewed in this paper and the influence of the more important variables such as temperature, pressure and molecular structure on solubility in liquids and gases is discussed. A suitable cbromatographic technique has been developed for determining low concentrations of water. Tailing of the water peaks has been elim inated by adding water to the carrier gas stream The method is applicable for both gas or liquid samples and is effective in the presence of hydrogen sulfide. The experimental study of water solubility in methane-hydrogen sulfide systems at a temperature of 16oF has shown that the presence of hydrogen sulfide causes only a modest increase in water content at pressures up to 1,400 psia. Theoretical considerations and data on pure hydrogen sulfide and carbon dioxide suggest that the effect of both these compounds will be greater at higher pressures and in the liquid phase. INTRODUCTION Before transporting or processing natural gases and gas condensates, it is usually necessary to dry them using suitable dehydration equipment. The design and operation of this equipment requires a knowledge of the amount of water present in the fluid at the reservoir and operating conditions. This is influenced by temperature, pressure and composition, particular1y when certain non-hydrocarbon components are present. Field experience indicates that hydrogen sulfide and carbon dioxide, for example, alter the usual water solubility relationships appreciably. However, an extensive search of the literature does not reveal any quantitative data on such systems. For sweet natural gases, generalized empirical correlations such as the one proposed by Katz, et al,6 can be used to predict water solubility with confidence at most temperatures and pressures of interest. However, existing theoretical relationships do not permit a calculation of the deviation from these curves when polar substances like hydrogen sulfide are present in the system. Thus one must resort to an experimental approach to obtain the necessary information. The fact that laboratory experimental methods frequently involve the use of mercury which reacts with hydrogen sulfide in the presence of water, and that hydrogen sulfide interferes with many chemical reactions specific for water has contributed to the difficulty of studying water solubility in systems containing hydrogen sulfide. In this investigation the water content of a limited member of methane-hydrogen sulfide mixtures was determined using a special technique with gas chromatography. REVIEW OF PUBLISHED DATA Experimentally determined water solubility data have been reported for methane, 14 ethane, 15 propane, 9 n-butane, 16 1-butene, 11 hydrogen sulfide 18 and carbon dioxide. 19 These studies report the effect of pressure, temperature and molecular structure on water solubility in single component gases and liquids. Fig. 1 compares experimentally determined water solubilities in several hydrocarbons, carbon dioxide and hydrogen sulfide at l00F as taken from this

By Leo H. Glanville

UNTIL 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115,000 cu. ft. per min., and since then fans and sprays have been added as required. ATMOSPHERIC CONDITIONS Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the normal average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low-about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24° to 95°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,490 ft.), makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. PROBLEMS Since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination. It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.

By Benjamin S. Lindsey, James Norman

Barite (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some binds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to I00 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaS04, II.II. per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coel for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1943

By M. Muskat

Calculations are reported on the differential sensitivity of the updip invasion of oil strata of varving permeability to the driving pressure differential. It is assumed that the water-oil interfaces advance with sharp fronts, or that the microscopic displacement efficiency is independent of rate and capillary pressure effects. It is found that, under such conditions, limitations of withdrawal rates will not greatly inhibit the "fingering" and bypassing tendency through high permeability strata unless the differential fluid head across the original oil column is of the order of or exceeds about 80 per cent of the driving pressure differential. In practice, such restrictions will be feasible only for oil reservoirs and aquifers of high permeability and dip, but may develop automatically under combined gas injection and water drive operations. INTRODUCTION A commonly expressed view regarding the intrusion of edge-waters into oil producing formations is that the geometry of such advance is rate sensitive. Specifically, it has been suggested that high rates of advance, stimulated by rapid withdrawals, will lead to "fingering" and an irregular type of invasion, whereas at low withdrawal rates the water encroachment will be more uniform. Two factors tend to support this view. One is the resultant effect of capillary pressure and gravity gradients in the displacement processes' involved in water intrusion, which are magnified at low rates of flow so as to improve the recovery efficiency. The other is the direct retarding effect of the rising water head as it advances upslope into the producing area. Capillary pressure forces give rise to a rate sensitivity of the oil recovery by water displacement in uniform strata as well as differential effects in non-uniform formations. These are basically independent of the effect of gravity and would also occur in horizontal beds or when the oil and water have the same density. Unfortunately, however, the fundamental equation describing the displacement process under the action of capillary pressures can be solved only by numerical or graphical procedures, and moreover the solutions are sensitive to the character of the capillary pressure and relative permeability curves.* On the other hand, the direct effect of gravity can be given a formal analytical solution if the simplifying assumption is introduced that the water advances with sharp fronts in the individual uniform strata. It depends on the absolute permeabilities of the water invaded zones and hence results in a rate sensitivity of the differential invasion in stratified media. Although a tieatment of this factor alone will not give a complete evaluation of the effect of rate on water intrusion in non-uniform pays, it should provide at least a semiquantitative measure of the sensitivity of "fingering" to withdrawal rate. Such a treatment will be presented in the following sections. GENERAL THEORY The basic element of the theory is the history of water advance updip in a uniform stratum (Fig. 1). In contrast to the assumption of constant flow rate, generally made in the analysis of displacement processes, we shall assume here that

Jan 1, 1951

By Walter Miller

A surprising development during the year was the continued high demand for petroleum products and the high level of crude oil charges to the stills. Generally speaking, the petroleum industry during 1946 succeeded in producing a greater quantity of crude oil and petroleum products than in any of the war years, and considerably exceeded the production of any prewar year. Daily crude still charges averaged between 4,700,000 and 4,800,000 bbl per day for 1946 and about equaled the 1945 record, although most pessimistic 1945 guesses, predictions, or fears ranged, for 1946, from only 3,900,000 to 4,400,000 bbl per day. In spite of the high crude charge to the stills, total stock of crude oil was higher at the end of the year by some 7,000,000 to 8,000,000 bbl. A similar story holds regarding stocks of the principal refined products. Gasoline on hand at year's end was two to three million barrels lower, and was considered low for the expected demand during the coming high consuming season, while stocks of light and heavy fuel oils, although some higher than a year previous, hardly reached a comfortable level. The trend in gasoline of high octane number, which has resulted in a marked rise in. the antiknock quality by the end of 1945 (five or six numbers higher than during the war and one number higher than the prewar quality of civilian motor gasoline of 1941) was abruptly arrested by an acute shortage of metallic lead for manufacturing tetraethyl lead. Government action in the form of lead price control, rationing, and the setting of octane ceiling specifications to conform to the reduced ethyl lead compound available were enforced until abrogated at the end of the year. It will be interesting to see how rapidly the octane levels will resume the rising trend, as more metallic lead slowly becomes available for making greater quantities of ethyl lead compound. As octane quality rises over present levels the disadvantage of the refiner without catalytic cracking equipment will increase. Gasoline made by catalytic cracking, without addition of ethyl lead, approximates 77 octane by the official ASTM Motor Method test, compared with 66 for gasoline generally similar in volatility made by the older thermal cracking operation. Catalytic gasoline shows an even greater improvement in the Research octane number, the comparison being roughly 86 Research versus 71 Research octane for the thermal cracked product. This higher differential in Research octane is credited by many, although not universally so, as contributing to better road performance, and consequently resulting in a more desirable product marketwise. In some parts of the country a premium of roughly one fourth cent per gallon is now being paid for gasoline with higher Research octane made possible by including catalytic cracked product in the final blends. If such price differentials in favor of catalytic gaso-

Jan 1, 1947

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By Louis Ware

At the beginning of the present war, the United States faced the need to multiply its production of magnesium metal almost roo times within the shortest possible period. Urgently needed for construction of military aircraft, incendiary bombs, and other war uses, magnesium was at the top of the list of critical war materials. Up to that time only one Producer, employing Only One process and using One raw material in a single plant, represented this country's entire Production capacity. It was immediately desirable to plan a numher of plants located strategically over the Count'Y and to expand an industry more rapidly and to a greater extent than ever before had been attempted in so short a time. In '939 this American producer, the Dow Chemical .9 was making about 7 million Pounds of magnesium metal. It utilized as a raw material brine containing magnesium chloride, which was pumped from wells in Michigan. The logical ap-preach to certain increased production was to employ the same process on the same raw material in other sections of the United States. In Europe and other countries, different processes had been used and different raw materials were being utilized, but all of the skill and knowledge for production in this country was that of using the Dow type of cell and magnesium chloride as a raw material. The Government was testing other processes, but none then had been proved commercially feasible. Development OF New Process The International Minerals and Chemical Corporation had available a large quantity of magnesium ,chloride at Carls-bad, New Mexico, contained in the end liquor produced from its potash plant sillce the buildng of the plant in 1941 It was the only company mining commercially a magnesium ore and having anything like this quantity of magnesium chloride liquor. The magnesium ore, langbeinite, was being mined from the 800-ft. level for its content of potassium sulphate. This ore, a potassium magnesium sulphate, was reacted in a base exchange plant with potassium chloride to produce potassium sulphate, the discharge liquor having a high content of magnesium chloride. Three potash-producing companies are in the Carlsbad area, but only International has developed and is commercially producing the potash-magnesium ores. The lower, or No. 4, veil, in that area is potassium chloride ore, and is continuous through all the properties. The langbeinite, or No. 2, vein is minable at the International property, but occurs sparsely, if - at in other areas being mined in that vicinity. It is understood that most of the mag. nesium produced] by Germany comes from magnesium and magnesium-potassium ores obtained from potash mines. It was logical for International to pro-pose to make available this magnesium material and to offer its technical staff to design, construct and manage a magnesium plant for the account of the Government. The plan that finally was adopted by the

Jan 1, 1944

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and .operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in. the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Be. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Bé. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944

By James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to loo per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By N. V. Peterson, R. S. Mason

Pumice, pumicite, and cinders are all products of explosive volcanic eruptions. Pumice and pumicite are produced by the violent expansion of dissolved gases in a viscous silicic lava such as rhyolite or dacite. Pumice is a light-colored, cellular, almost frothy rock made up of glass-walled bubble casts. It may occur as coherent, massive blocks composed of highly vesicular glassy lava in either a flow or vent filling, or it may be more or less fragmented by violent eruption. Pumicite has the same origin, chemical composition, and glassy structure as pumice differing only in particle size. Particles less than 4 mm in diam are designated pumicite. Pumice is usually found relatively close to the vent from which it was erupted while pumicite may be carried by winds for great distances before settling as an accumulation of fine-grained ash or tuffaceous sediment. Volcanic cinders are the reddish to black vesicular fragments that pile up during explosive eruptions of volcanoes of basaltic composition. Most deposits of cinders occur as cones or mounds of stratified fragments that range in size from a fraction of an inch to several inches in diameter. Individual cones or mounds of cinders may be several hundreds of feet in diameter and as much as 500 ft high. Properties The properties that make pumice and pumicite useful in industrial applications include: low-bulk density, good heat and sound insulating properties, and excellent abrasive capability. Cinders, even though less cellular and somewhat heavier, also have a variety of industrial uses. Uses The main use of pumice and cinders continues to be in the construction industry as road-surfacing material, railroad ballast, building block aggregate, in lightweight structural concrete, and as plaster aggregate. Both pumice and pumicite continue to be used as abrasives for polishing glass, metal, leather, stone, and wood. Some scouring powders and soaps also contain pumicite. Minor uses include fillers, absorbents, carriers for insecticides, catalyst carriers, filters, and soil conditioners. Pumicite is also used in sizable quantities as a pozzolanic additive in monolithic concrete where it increases the workability, strength, and durability of the concrete and reduces the heat of hydration. Volcanic cinders are generally denser and more coarsely cellular than most pumice. Markets for cinders include aggregate for road construction and surfacing and in lightweight concretes, particularly blocks. Some producers having access to both pumice and cinders offer a variety of blends of the two materials to block manufacturers. Most pumice deposits are unconsolidated and usually have a minimum of overburden. Mining is by open pit and can be easily carried out with conventional loading equipment. Sometimes air-drying precedes hauling to a crushing and screening plant which yields the size product desired. Multiple bins at railroad hauling facilities permit blending if desired. Pumice for abrasive use may require more sophisticated processing by fine grinding and air classification before being bagged for market. Block pumice in economic quantity and quality is limited to a few geologically young

Jan 1, 1975

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942