Search Documents

By Frank C. Appleyard

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other principal calcium sulfate mineral has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhydrous form of calcium sulfate (CaSO,) whereas gypsum is the dihydrate (CAS0;2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. However, of most importance is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaS0;Vi H,O) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advantage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which when mixed with water would form a putty that could be "plastered" on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of its quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term "land plaster" for ground gypsum has remained in use. Another cementituous material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered and it has today almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $500 million per year as illustrated in [Table 1].

Jan 1, 1975

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By J. W. Hickman, E. A. Gulbransen

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By G. A. Croes, N. Schwarz

The dimensionless groups, to which the variables that govern the displacement of oil from reservoirs by liquids can be combined, are derived. Three types of displacement are considered, viz. cold-water drive, hot-water drive and solvent injection. The derivation of the dimerzsionless groups is carried out by means of the relevant basic equations (in-spectional analysis). The resulting sets of groups are afterwards completed by means of dimensional analysis. The form of the groups is given in such a way that they can be adapted to suit the various boundary conditions that are encountered in practice. The physical meaning of the groups is discussed. They have all been brought together on a chart, from which their mutual relation and their corresporzdence to related dimensionless groups in common use in other engineering sciences can be read off. The limitations of dimensionally scaled model experiments as a useful tool for studying liquid flow in porous media, as occurring in oil reservoirs, are discussed. The use of models to study fluid mechanics has an appeal for everyone endowed with natural curiosity. What active boy has not played with ship and airplane models, or crude models of dam and drainage systems Even in the most advanced technical engineering, such models play a fundamental and indispensable role. "And yet in few departments of the physical sciences is there a wider gap between theory and practice, between scientific knowledge and the state of art, than in the use of models to study hydrodynamic phenomena." Garrett Birkhoff1 INTRODUCTION Laboratory displacement experiments are extensively used to investigate, directly or indirectly, the production behavior of petroleum reservoirs. Such experiments are representative of the reservoirs as a whole, if they are carried out with models that are "properly scaled." The performance of oil reservoirs is governed by the values of a number of variables, which can be combined to dimensionless groups. Two general methods are available for the derivation of these groups. In the first of these, dimensional analysis, combination of the variables is done essentially by trial and error. Its only premise is knowledge of the complete set of relevant variables. In the second method, inspectional analysis, the dimensional homogeneity of the equations describing the behavior of the system to be studied is used. The resulting dimensionless groups can be divided into: (a) independent (variable) groups, such as dimensionless length, time, etc.; (b) dependent groups, giving the dimensionless form of the variables, such as recovery and pressure, that can, at least in principle, be measured during an experiment; (c) similarity groups, which are independent constant groups, such as ratio of length to height of the reservoir and ratio of

Jan 1, 1957

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956

By E. A. Gulbransen, J. W. Hickman

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By D. H. Woodard, G. W. Geil, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By E. A. Gulbransen, J. W. Hickman

IN a previous paper1 the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300° to 700°C. except for copper, where the range selected was 100° to 500°C. The results of these studies were presented in graphical form as existence diagram, of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviations in lattice parameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: I The existence diagrams of various alloys. [2.] The effect of the structure of the [ying] metal on the existence diagram of Iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body- centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K42B1 Nichrome V, Hipernik, Inconel, Stellite " 21," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1946

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

Discussion of the paper of John H. Hall, presented at the New York. Meeting, October, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1247 to 1256. WILLIAM 'R. WEBSTER, Philadelphia, Pa.:-I would like to call ,attention to the fact that the results of the ordinary tension and bend tests do not always give us the information we want even if we figure out the amount of work done. You want a bending test of sufficient width and full thickness. In the case of eyebars, for instance, I have had experience with a 10- by 1-in. eyebar which gave perfectly good results in a full-size test of the finished bar. The 10- by 1.5-in. and 10- by 1.75-in. eyebars from the same heats-of steel were absolutely worthless in full-size tests. The narrow bending tests from all these bars gave good results. Bat after going into the matter fully, we found that if pieces about 3 in. wide and full thickness were used for the. cold bending tests, the heavier material would not stand this test, but failed. That is, in order to check the quality of the rolled bar you should have a wide piece of full thickness for cold bending, as the narrow pieces give misleading results. J. E. JOHNSON, JR., New York, N. Y. :-I would like to ask if there have been any tests made to compare the results of Charpy tests with the true dynamic test similar .to the Wohler test, except that the piece is subjected to a tensile or compressive stress and to alternating stresses in addition, at the same time. This seems to me to approach more nearly than any other test to the conditions of actual service. where the piece is under a fixed initial stress plus a highly variable and often alternating stress. Some tests were made on this plan in England within a year or two. The test piece was Subjected to either a tensile or compressive stress of known amount and simultaneously to alternating stresses in addition. Such a. test as this gives information which we cannot get by a tensile test or even from the tensile strength multiplied by an. elongation. Such tests, however, are exceedingly tedious and require long periods of time in order to obtain valuable results. If material could be subjected to these dynamic tests and the same material to the. Charpy shock test, and if some reasonable qualitative relation could be established between the results of the two tests, then we could assume that the shock test, which is so simple and easy to make, was a measurably accurate test of the dynamic qualities of the material. At present it does not seem

Jan 12, 1913

By Richard Paul Seelig

THE following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which may stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. EXPERIMENTAL APPROACH The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. In as much as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a compressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Al- though these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself,8 calls attention to the fact that the properties

Jan 1, 1947

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.' In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium's lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By G. K. Manning, A. R. Elsea, A. B. Westerman

A considerable number of high-tem-perature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. .4t the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in vitalliurn after various heat treatments. Howcver, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chro-mium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja and Guertler2 indicated that cobalt and chro-mium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to 85 pct chromium undergo a transformation at [zoo to 12 50 c More recently, Wever and Haschimoto,3 Wever andLange,4and Matsunaga5 carried Out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallogra~hic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Mat-SUnaRa. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these excep-tions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data arid the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitalhum by deter-mining the diagram for the cobalt-chro-mi~m system- Experimental Work For the convenience Of the reader, the diagram as determined by the present investigation is presented in Fig 3. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the melting point for pure chromium is the

Jan 1, 1949

By B. Russell, J. R. Tuffley

The stability regions of the normal sulfate and the various basic sulfates of lead in 02-SO2 and PhS-SO2 gas atmospheres were calculated from available thermodynamic data over the temperature range 600o to 1200oC. Roasting experiments were carried out on samples of synthetic lead sulfide at various temperatures and for various roasting times. Compounds in the oxidized surface layers were identified by X-my techniques. The order in which the various reactions occurred was determined by considering the experimental results in conjunction with the thermodynamic calculations. The results of these investigations were applied to the sintering of lead sulfide concentrates, and the extent to which each of the various reactions occurred in a sinter bed was determined. PRODUCTS which may be formed during the roasting of PbS are PbS04, PbSO4. PbO, PbSO4 . 2PbO, PbSO4 . 4PbO, PbO, and Pb.1, 2 The formation of some sulfates has been studied by a number of investigators3-' whose experiments have mostly been confined to the temperature range between 500" and 850°C. Culver, Gray, and spooner3 were able to isolate the reactions which formed PbSO4 and PbSO4. PbO by carefully controlling the compositions of the roasting gases. The kinetics of these reactions were studied within the temperature range 673" to 807°C. Gardner4 and Merrick5 also studied the kinetics of oxidation of PbS. Gardner disregarded the existence of basic sulfates and, as a result, misinterpreted some of his experimental data. Merrick recognized that most of the products of oxidation were mixtures of basic sulfates, but was unable to identify the individual components. Hoschek6 oxidized PbS in air at temperatures up to 800°C. The products were analyzed after roasting had proceeded for some minutes, but no attempt was made to follow the reactions in the initial stages. Consequently, no roasting mechanism was derived. He also showed that PbSO4 and PbSO4 - 4PbO decomposed slowly in air at temperatures in the region of 800°C. The stability regions of sulfates in the temperature range 500" to 850°C have been only partially determined, while practically no information is available for higher temperatures. In the lead sintering process, PbS concentrates are roasted at temperatures within the range 1000o to 1200°C. In order to investigate sulfate formation, it is necessary to determine the effects of temperature and gas composition upon the various oxidation reactions and upon the regions of stability of the various lead sulfates. Kellogg and Basu2 introduced an equilibrium diagram similar to those in Figs. 1 to 3 which provides a convenient medium for represent-

Jan 1, 1964