Search Documents

By Warren L. Baker, I. J. Logan

By 1950 or soon thereafter facilities will be available in foreign countries for the production, transportation, and refining of about 4,305,000 bbl per day of crude oil—a volume not far short of current United States output. This is indicated by announced plans for foreign expansion, - some of the work being already under way. The projected potential production is about 1,500,000 bbl per day or 50 pct above the record-setting foreign production of 2,810,000 bbl daily in 1946. The scheduled new foreign facilities are equivalent to almost one third of the present facilities of the United States. Fears that so much additional foreign oil may flood world markets and disrupt the domestic industry of the United States are not justified. The projected foreign expansion apparently has been planned on a sound business basis, with careful consideration of the world's actual need for all the projected additional production. Materially increased world demand for petroleum promises to absorb the increased supplies without ill effect upon the domestic industry. Even by applying conservative estimates of both foreign and domestic demand, it is indicated that world requirements can absorb the projected larger foreign output and still permit continued increase in United States production. World demand would have to increase only 5.7 pct per year in the 1947 to 1950 period to absorb the prospective supply. Such an increase may be conservatively projected, in view of past and current trends. Introduction Recent announcements of plans for expanding petroleum facilities in the Middle East and Venezuela foreshadow an unusually sharp increase in foreign production in the immediate future. Therefore, the next few years will bring far-reaching changes in world petroleum affairs, with foreign petroleum production and other activities assuming much greater importance than formerly. Tabulation of figures on development already under way or planned indicates that in the next several years facilities will be available for producing, transporting and refining twice the prewar production of foreign fields and about 50 pct or nearly 1,500,000 bbl a day above their record-level output of 1946. To say that foreign fields may be producing such an enlarged quantity by 1950 is, of course, a statement of great significance to everyone connected .with the oil industry and especially to those of the American petroleum industry. A production of 1,500,000 bbl daily is equal to the combined yield of the states of Oklahoma, Kansas, Illinois, Louisiana, Arkansas, Mississippi and New Mexico. This means that within the next several years foreign petroleum facilities will undergo a new expansion equivalent to one third of the present facilities of the United States. To think of such an expansion in foreign production is to raise at this meeting the question of what this prospective foreign development means for the United States, the American petroleum industry in general, and the American engineer and technologist in particular. It is only logical to question whether or

Jan 1, 1948

INTRODUCTION The preceding chapters have brought us to a point in the mineral appraisal process where the composited sample values can now be used to estimate the grade and tonnage of the total mineral deposit. There are many techniques whereby drill hole composites and/or other sample data are used to assign grade and estimates to the surrounding rock. Matheron and his students have properly called such techniques extension functions. Before embarking upon a detailed discussion of extension functions, it is necessary that we take time to consider the concept of geostatistics as advocated by George Matheron who developed the "Theory of Regionalized Variables," which he published in 1962 (Matheron, 1971). The concept of regionalized variables has important application in the techniques of mineral appraisal. The position or location of a mineral sample within a deposit can be almost as important as its value. Geostatistics, when defined as "the application of the theory of regionalized variables* to the study of mineralized volumes of rock," takes into consideration the position as well as the magnitude of the value of the sample. The principles of geostatistics, as outlined by Matheron, represent a major step forward in the mineral evaluation process, because they provide a sound theoretical and practical basis for quantifying the geological concepts of (1) area of influence of a sample, (2) the continuity or lack of continuity of mineralization within the ore body, and (3) the lateral changes in mineralization according to the trend direction of an ore body and its orthogonal components; or in other words, a measure of the anisotropy of the deposit. Royle (1971) has defined the objects of geostatistic as being: "1. To estimate the most likely value of blocks of ore, or the values of the whole deposit; and 2. to estimate the errors of such estimates. This latter is important as, in addition to providing a check on unwarranted optimism, it shows where more valuation work may be needed." Because of the great importance of these concepts in mineral evaluation, an introduction into the theory of regionalized variables, and the study of a practical approach to its application is outlined here. REGIONALIZED VARIABLES VS. RANDOM VARIABLES Classical statistics, as discussed in earlier chapters, grew out of the study and application of probability theory. Probability is concerned with the outcome of random events and therefore classical statistics is built upon the theory of random variables, i.e., the probability of independent events. The validity of most statistical inferences depends upon sample randomness being assured for unbiased results. Where independent events cannot be assumed the results of statistical inference becomes suspect. On the other hand, geostatistics is concerned with variables that have position in space as well as magnitude, hence the term regionalized variables. Mineral deposits are not the only field to which the theory of regionalized variables is applicable. Many natural phenomena that demonstrate a relationship between change in magnitude and position in space are amenable to application of geostatistical techniques. Mineral deposits vary greatly in their geosta-

Jan 1, 1980

By M. A. Torcaso, P. Raimondi

The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil. A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sor The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston-like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. INTRODUCTION A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two-phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would be represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil. called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition. of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important.

Jan 1, 1965

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, vet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 9.99 per cent saturated at each temperature. The speci¬men was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully [carburized] specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By E. V. Potter, E. T. Hayes, H. C. Lukens

Large volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that bite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.l.2 The close relationship between iron and manganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. Apparatus The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of IOO C.C. for a 60-cm. length. For larger changes in gas volumes, auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By W. W. Yankie, A. T. Chatas

This paper is written as a discussion of the paper, "Buckling of Tubing in Pumping Wells, Its Effects and Means for Controlling It" by Arthur Lubinski and K. A. Blenkarn, which war published in the March, 1957, issue of Journal oP Petroleum Technology. An analogy is drawn between the buckling of tubing in pumping wells and a fiube, fitted with frictionless pistom, linked by an inelastic rod, and which is subject to an internal pressure. A simple derivation shows that the critical internal pressure exerts a hydrostatic force on the pisfon which is close to the Euler load for compression buckling of the same tube. While the results agree with those of Ref. I, the basis of calculations has been changed and clarified. The presence of internal upsets at the pistons is discussed. INTRODUCTION In the Appendix, Lubinski and Blenkarn state that a tube with ends closed by frietionless pistons connected by an inelastic rod (Fig. 1) will behave as a column loaded with a force equal to the tension force in the rod. They note that, while the fluid may not resist a shear force, the moment in every cross section is piston force multiplied by the elastic line deflection (c.f., the loaded column). Since the equations of the elastic lines are similar in the two cases, the solution is carried over from the loaded column. On the contrary it is suggested that while the method of solution remains unchanged from the column case, the actual stress distribution is different, a fact which is taken into account in this note. A simple method of approximating the buckling pressure is given, and their reasoning in our mathematical language is continued. GENERAL EQUATIONS The equation of an elastic line, initially straight in the x direction (Fig. 2), is given by In the case of a loaded column, this may be written: For the pressurized tube it was shown, by analogy with the loaded column, that tion has a solution that, for P, = EI/P, any deflection is stable (a criterion for buckling). An attempt will be made to describe more precisely, the forces acting on the tube, and to analyze the buckling condi,tions. DISCUSSION If the tube assumed a deflected position, the volume between the pistons would increase so that in deflecting, the energy of the fluid would decrease. When the increase in elastic energy of the tube (due to bending) is equal to the decrease of fluid pressure energy, buckling conditions exist. Analyzing the forces on the tube (Fig. 3), two transverse forces, T,, T,, exerted by the pistons, are balanced by a resultant of the pressure elements which are linearly dependent on the local curvature of the elastic line (Fig. 4). Unlike most buckling cases, the forces depend on the shape of the elastic line, a condition that makes a rigorous mathematical treatment difficult. Several approximations may be used to clarify the problem.

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pig-ments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 A as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut. In light of the above, a project was initiated for the formation of single crystals of rutile. Method of Formation of Rutile Single Crystals Fortunately, purification of TiO2 produced from both titanium tetra-chloride and titanyl sulphate solutions had reached the stage where spectro-graphically pure starting material could be made. Spectrographic analysis of the feed material used in the initial experiments is compared with the present feed material in Table 1. It is apparent that the present large scale purification is approximately as good as the original experimental, small scale purification. Verneuil1 produced synthetic ruby and corundum in 1904 by the well-known flame fusion process, which today bears his name. Except for mechanical improvements the present commercial production of synthetics by flame fusion is essentially unchanged from his initial method. His burner consisted of an inner orifice through which was fed the feed material and oxygen. Surrounding this was a larger outer orifice through which was fed hydrogen at lower pressure. This arrangement consists then of a lance of oxygen burning in an atmosphere of hydrogen. The proportions of hydrogen to oxygen usually used in corundum production is about 3:1, providing there is sufficient temperature to reach the 2050.°C required for the fusion of alumina. From work done in the Titanium Division Laboratories2 and from the published work of Erlich3 it was known that rutile appears to lose oxygen near its melting point and that it would not be possible to grow single crystals in a strongly reducing environment. Consequently, in order to determine whether single crystals could be grown at all, an Airco oxygen-acetylene torch with

Jan 1, 1950

By R. W. Gurry

When a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, yet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. Experimental Procedure Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;' it suffices to state here that the carburization lasted about I40 hr. at 760°C. (1760°F.) and 44 hr. at iiio°C. (2030°F.), these periods being long enough-—on the basis of the calculations presented later—to ensure that the specimen was about 99.9 per cent saturated at each temperature. The specimen was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully carburized specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By R. W. Gurry

When a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, yet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. Experimental Procedure Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;' it suffices to state here that the carburization lasted about I40 hr. at 760°C. (1760°F.) and 44 hr. at iiio°C. (2030°F.), these periods being long enough-—on the basis of the calculations presented later—to ensure that the specimen was about 99.9 per cent saturated at each temperature. The specimen was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully carburized specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By R. H. Brown, F. Keller

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By H. A. Wriedt

At 500°C (932°F) the range of y' iron nitride is from 5. 77 + 0.03 wt pct N (in coexistence with a iron) to 5.88 * 0.03 wt pct N (in coexistence with E iron nitride). Stoichiometric "Fe,N" (5.900 wt pct N) is near the upper extreme of possible compositiom. The depe-dence of nitrogen activity (expressed as pnh,/Ph,) on nitrogen content is described satisfactorily by a "Langmuir" isotherm: At even the highest nitrogen concentrations, less than 0.18 pct of' the nitrogen atoms present are impositions of disorder. Past investigations1-4 of the Fe-N system have left only details of the thermodynamic behavior of the y' nitride, "Fe,N9', to be studied. The present investigation was made to establish more precisely than hitherto the limits of composition and the relation between composition and nitrogen activity at 500°C. EXPERIMENTAL TECHNIQUE The compositions of nitrides in equilibrium with various NH, + Hz mixtures at 500°C were determined from the weights gained by 0.02-in.-thick (4.0 to 4.5 g) strips of purified iron* when the nitrides were formed A description of the gas generation and furnace system has been published.5 Cracking and blistering during conversion of the original solid iron at 550°C injected considerable porosity into the strips without causing their disintegration. The time for complete conversion was significantly lowered by periodically reducing partly nitrided specimens in hydrogen and then reexposing them to the nitriding gas. Gas mixtures producing single-phase were used in the equilibrations at 500°C. Equilibrium was regarded as existing when the specimen weight was not detect-ably affected by further exposure to the same conditions. The gas compositions and nitrogen activities at which y' transformed to a iron (lower activity limit) and to E iron nitride (upper activity limit) were redetermined during the investigation. A specimen was equilibrated in an NH, + Hz mixture at 500°C and then exposed to a s1ightly different gas. When equi- librium had been reestablished the gas was again changed slightly. At each stage of this repeated process, while the specimen was reacting with the gas, the variation of its weight with time was observed. The onset of phase transition was marked by an abrupt change in the amount and rate of weight gain or loss. The specimens were weighed outside the furnace, in air and at room temperature, on a balance with 0.05 mg precision. When it was found that the specimens were oxidizing at a significant rate during the weighing, a series of timed weighings was made with each specimen, starting 1 min after its exposure to air. RESULTS AND ANALYSIS The gain in specimen weight from oxidation during weighing was linear in the logarithm of time between 1 min and about 2 hr, Fig. 1, later becoming linear in the cube root of time. In the logarithmic period, nitride specimens oxidized two to three times as fast as

Jan 1, 1970

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By James H. Courtright, Kenyon Richard

L. H. Hart (Chief Geologist, American Smelting & Refining Co.)— Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term brec-cia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geological history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala. Although the following comments are intended primarily to emphasize points brought out in the article by Richard and Courtright, certan subsequent detailed mapping by Hollister and Houston7 within the main central mineralized area of the Toquepala deposits not only supports most of Richard's and Courtright's con- clusions but also contributes additional facts that strengthen and broaden the whole concept of the origin of the Toquepala breccia pipes. In detailed mapping by Hollister and Houston,' the most significant feature disclosed is a well developed system of concentric fracturing in rocks peripheral to the main breccia pipe throughout an arc of 300°, interrupted only by the late dacite agglomerate in the north quadrant. Although Richard and Courtright noted that such fractures were developed in the southern and southeastern areas, continuity in the east and west quadrants is established by consistent orientation of the stronger set of fractures and joints. The existence of these structural weakness trends is emphasized by the emplacement of dike-like phenomena in and along members of this fracture system. Richard and Courtright described one of these dikes in the southeast quadrant. They referred to it as a ring-dike, composed of dacite porphyry. This suggests an apparent structural control of at least a part of the dacite porphyry intrusion by features related to the Toquepala breccia pipe center. This raises a perplexing question, since the dacite porphyry intrusion had been presumed to antedate breccia pipe activity. However, if this ring-dike is related to the breccia pipe center, it may indicate that some part of the dacite porphyry intrusion advanced in a manner resulting in an intensely localized stress center, which produced the concentrically arranged fracture system. The ring-dike would then appear to be evidence strongly sug-

Jan 1, 1959

By H. C. Howard

Reaction of oxygen and bituminous coal starts as soon as the coal bed is exposed to air and, with some coals, proceeds with significant velocity even at normal temperatures and at normal oxygen partial pressures of one-fifth of an atmosphere. At higher temperatures, the reaction is greatly accelerated and ultimately a condition is reached where the process is very rapid and we then speak of combustion. It is the purpose of the present paper to discuss the reactions of oxygen and coal at temperatures below those of active combustion. It is these low temperature oxidation reactions which are responsible for heating in storage and for marked changes in agglutinating proper-ties. These reactions may also be employed for the preparation of organic acids, which are of direct interest to the chemical industry. For convenience in discussion, the low temperature reactions of oxygen and bituminous coal can be roughly divided into three stages though there is, of course, overlapping. Stage I is a surface oxidation stage, characterized by the addition of oxygen, with the formation of oxygen containing groups some of which have acidic properties. Carbon dioxide, carbon monoxide and water may be formed con-comitantly and are always liberated at higher temperatures, and in cases where the oxidation is prolonged. Superficially, the coal is little affected by this primary stage of oxidation and usually only minor changes in ultimate composition result. There may be definite changes in coking and coking properties, and heat of combustion susceptibility to further oxidation. The presence of acidic groups can be demonstrated by specific reactions. These groups may show cation exchange properties like the mineral zeolites. The formation of oxalic acid has been reported. If the oxidation is continued, a large fraction of the organic material of the coal is converted ultimately into alkali soluble, acid insoluble products, which have been given the name "regenerated humic acids" and which are the characteristic products of Stage 2. These humic acids, in the solid stage, do not differ greatly in appearance from the original coal, but show large differences in chemical composition and chemical and physical properties. Along with the humic acids, carbon dioxide and some of the water soluble types of Stage 3, are also formed. If the oxidation is carried still further, the humic acids may be degraded completely to the simpler, lower molecular weight acids of Stage 3 which are characterized by solubility in acid as well as in alkaline media, and by their orange, yellow or white colors. Additional carbon dioxide is formed in the transformation from Stage 2 to Stage 3 and, for a number of American coals, a maximum yield of the water soluble types of acids is reached when about 50 pct of the carbon of the coal is converted to carbon dioxide. Primary Oxidation The initial step in the reaction of gaseous oxygen on coal, like that on carbon,

Jan 1, 1949