Search Documents

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By Horace V. Winchell

The laws here referred to are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry. Reason Number One The first objection to the continuance of the present law is that it was not planned by its framers and the Congress which passed it to apply to many of the kinds of mineral deposits, nor to the mining conditions, which are controlled by it to-day. In 1866, under the title, "An Act granting the right of way to ditch and canal owners over the public lands, and for other purposes," was surreptitiously smuggled into existence our first mining law (14 Stats. at Large, Chap. 262, p. 251). This law provided that "whenever any person or association of persons claim a vein or lode of quartz or other rock in place, bearing gold, silver, cinnabar or copper, having previously occupied and improved the same according to the local customs or rules of miners in the district where the same is situated," etc., a patent might be granted an certain conditions. This was evidently an Act intended to validate claims already initiated, and to accord Federal recognition to mining locations made in

Jan 1, 1915

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

By D. L. Martin

The study of cobalt-platinum alloys has been of interest since they represent a class of permanent-magnet material in which the disorder-to-order transformation plays a controlling role. The magnetic properties of alloys in the range 40 to 60 at. pct have been found to be greatly influenced by composition and heat-treatment. The peak properties of 4700 coercive force and 9,000,000 gauss-oersteds energy product were obtained by controlled cooling and aging. These high values combined with ductility and machin-ability give the alloys useful characteristics although their high cost limits their application. THE cobalt-platinum alloys have been of interest in the study of permanent-magnet materials ever since the discovery by Jellinghaus that they had unusually high coerceive-force values.' The high coercive force was associated by Jellinghaus with the disorder-order reaction which occurred in these alloys. This was later verified by Gebhardt and Koster in a detailed study.2 An investigation of the structure, mechanism, and kinetics of the disorder-order transformation and resulting property changes in cobalt-platinum alloys has been in progress for some years. Certain phases of this study related to equilibrium rela- tions, and to the mechanism and kinetics of the ordering reaction have been published previously.3-5 In this paper, the results of the processing and heat-treatment studies on 40 to 60 at. pct CO alloys are presented. The magnetic properties have been found to be influenced greatly by the composition, by the cooling rate from the disordering treatment, and the final ordering time and temperature. Coercive force values, Hc, of 4700 oersteds and energy values, (BH)m, approaching 9,000,000 gauss-oersteds have been obtained by controlled cooling and ordering. PROCESSING OF THE ALLOYS The composition range of interest for permanent-magnet properties centers around the equiatomic composition Copt. In this region the alloys are dis-

Jan 1, 1959

By R. J. Watson

In an earlier paper, Ehrenburg and Watson1 published the develop ment for a potential function by which it is possible to obtain the electric potential at points on the surface of the ground when a current I passes between two electrodes and the subsoil is composed of parallel, homogeneous layers. In view of the continued interest in the resistivity method of electrical prospecting, the author has considered it desirable to publish the results of a number of theoretical studies making use of this potential function, and also the results of a considerable number of tests with models designed to show the soundness of the mathematical theory. It is hoped that these results will prove how erroneous the various empirical rules for depth determination may be. It has always seemed puzzling to the author that one can find, in papers published comparatively recently, statements upholding empirical rules for depth determination, and attributing most of the irregularities of resistivity curves to vertical discontinuities in resistivity in the subsoil. It would indeed be fortunate for the geophysical investigator if such a simple rule held. However, numerous investigators have proved both theoretically and by the success of their field work that such a rule does not hold, even by a "rough approximation" in many cases. On the other hand, as is shown in the development to follow, if the underground conditions are favorable it is possible for such empirical rules to give a satisfactory depth determination. Authors should be more careful about making such sweeping statements about the accuracy of these empirical rules because the relative simplicity of the field work places the method in the hands of any interested experimenter, and he is likely to become completely disgusted with the method after he has made several obviously wrong interpretations by empirical rules. There are simple and rapid methods for finding out whether the ground beneath the electrodes is sufficiently similar to the conditions

Jan 1, 1934

By Donald Ingvoldstad, Harold E. Lee

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were .provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through ¼in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

INTRODUCTION The geology of porphyry copper deposits in the southern Cordilleran orogen is the subject of this chapter. The area considered extends northwest from southern Mexico to the Columbia volcanic plateau, the Cascade volcanic province, and the Idaho batholith. Transversely it is a belt some 800 km (500 miles) in width bounded on the west by the Sierra Nevada range. Included within this area are many large segments considered unfavorable for hosting porphyry copper deposits, which are mentioned in the text. The region and its porphyry copper deposits have probably been more intensely studied and reported in the literature than any other area in the world. This summary considers regional geologic controls that governed formation of porphyry copper deposits within this province. Geologic factors that influenced the mineralogy and metallogeny of the deposits are also examined. Discussions with H. R. Cornwall have greatly helped in writing this section. GEOLOGIC SETTING The geologic setting has been summarized by Anderson (1966), Burchfiel and Davis (1972), Rogers, et al. (1974), and Lowell (1974). No porphyry copper deposits in this area are known to be pre-Triassic, so Mesozoic and Tertiary events will be stressed. Figs. 40 and 41 show basic data believed most pertinent to the topic of porphyry copper deposits. Pre-Middle Jurassic: Figs. 40 and 41 contain the principal structural and crustal ele¬ments found in the Cordilleran orogen after Anderson (1966), Schmitt (1966), Coney (1972), Rogers, et al. (1974), and Lowell (1974, 1976), together with location of some of the more important porphyry copper deposits. The western limit of the Precambrian craton is shown in Fig. 40 (Rogers, et al., 1974). East of that limit the crustal environment through which the porphyry copper plutons ascended includes the Precambrian basement as well as varying thicknesses of Paleozoic shelf and platform accumulations. The northwestern and western portion of the southern Cordilleran orogen west of the Rogers, et al. (1974) limit of Precambrian basement has what Churkin (1974) calls a thin continental crust. Brooks (1976) and Churkin (1974) describe oceanic volcanic

Jan 1, 1978

By R. B. Sosman

INTRODUCTION IT is well known that ferric. oxide, Fe.-,03, is paramagnetic, while magnetite, Fe304, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe-03 and Fe304 have been almost completely lacking. Fe203 and Fe304 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe203 toward Fe304, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe304, but it has not yet been possible to establish the existence-of such a break experimentally. The occurrence of solid solution ill this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe203 to Fe304. The oxygen-pressure curves at 1,100° and 1,200° are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe203 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is im-possible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe304 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great hulk of natural oxides of iron lie fairly near either Fe203 Or Fe304 in composition. The reason will be

Jan 6, 1917

By Paul A. Bailly

2.1-1. The Exploration Function in the Mineral Industry. With regard to a new mine, exploration can be technologically defined as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet, and annual output of the new extractive operation based on a certain mineral deposit. The activities that follow such a decision are called first development, then operation (90). Thus, in the U.S.A., exploration may continue in the technological sense after a mineral property has entered the "development stage" as defined for tax purposes. Regulations under Sections 1.615.1 and 1.616.1 of the U.S. Internal Revenue Code state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer" (95). There are, of course, many instances where additional later exploration discloses additional reserves which justify a plant much larger, more efficient and more profitable than the minimum feasible commercial operation. After a surface mine is put into operation, additional search generally will increase the reserves and thus warrant expansion of the rate of output and/or extend the life of the operation. The methods and techniques in such search are similar to those used in predevelopment exploration. This activity has produced a major part of new reserves for all mineral commodities but is not considered as exploration in the context of this chapter. The objective of exploration is, briefly stated, to find and acquire a maximum number of new economic mineral deposits with a minimum cost and in minimum time. The search must be so organized as to maximize the overall probability of discovering commercial mineral concentrations within a minimum time with the funds available. As shown by Celasun (27) these statements are neither adequate nor complete from a pragmatic point of view. Each actual exploration venture must define its objectives in terms of a minimum rate of return on investment for any deposit found

Jan 1, 1968

By W. H. Schacht

The operations of the Copper Range Co. are located in the Michigan copper district at the southern end of the Keweenaw Peninsula, 8 miles southwest of Hough ton (the center of the district). All the producing mines are situated in a long narrow zone paralleling the peninsula and occupying the central portion. This zone is about 25 miles long and 3 to 4 miles wide. The important mines, in their order from northeast to southwest, are, Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet & Hecla, Osceola, Franklin, Quincy, Isle Royale, Baltic, Trimountain, and Champion; the last three are operated by the Copper Range Co. The existence of copper deposits in this district became known soon after the discovery of America. Many references by early explorers show that copper was found in the possession of many of the American Indians that inhabited the Great Lakes region. There is abundant evidence that exploration of these copper deposits extended into prehistoric times; and some indication that the American Indians carried on operations shortly before the advent of white men. An account of the finding of primitive mining appears in the Government publications of 1850-51 by Foster and Whitney. Although earlier expeditions by white men had been made to the Keweenaw peninsula, an attempt to commercialize the district was not made until after 1765, when Alex. Henry, a British subject, searched the shores of Lake Superior for mineral treasure. His first expedition took him to the Ontonagon River, where he found the famous mass of copper now on exhibition at Washington. In 1771, he started operations along this river with a crew financed by English capital; but after much difficulty and only meager success he found only detached masses while in search for a major deposit. There is no record of any cxploration from 1774 to 1820. In 1838, Dr. Douglas Houghton was appointed state geologist. Prior to that time he had made several visits to this region; and was the first white man to find

Jan 1, 1925

By Etienne A. Ritter

The Evergreen mine, located at Apex, in the northern part of Gilpin county, Colorado, has opened a very peculiar and interesting copper-deposit, in which both bornite and chalcopyrite occur as rock-minerals. The country-rocks are crystalline schists cut by dikes of granu-lite and of pegmatite. At the Evergreen property they have been cut by a dike of a uew kind of eruptive rock, to which I have given the name " Evergreenite." The rock is composed of quartz, alkali feldspars, orthoclase and albite (often interlocked as microperthite), with augite of the ægirine variety and long needles of enstatite and diallage. For reasons stated below, I believe the dike to be of Tertiary age. It is easily traced on the surface of the ground, from a point in the bottom of Pine creek, about a mile below Apex, to the top of Nevada hill, 1,500 ft. beyond and 600 ft. above it. (See Fig. 1.) It varies from 3 to 12 ft. in width, and is bounded on both sides by contact-zones about 60 ft. wide, in which the crystalline schists have been changed into pseudo-quartzites or pseudo-gneisees, according to the injection of an excess of quartz or of feldspars through the special layer of the schists. The most interesting feature is the presence of the pyroxenes, which are always found, though in very variable proportions from place to place, in the layers of these metamorphosed crystalline schists. The dike has torn from its walls a large number of fragments of the wall-rock. It must have been in a viscous state when that happened, because these fragments of the wall-rock do not show any sign of resorption or of assimilation by the magma. In places they are so distinct and so numerous that the rock looks to the naked eye like a pseudo-breccia, of which, never-

Jan 1, 1908

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By I. R. Kramer

Single crystals of aluminum were pulled in tension in a solution of paraffin oil and stearic acid. The critical resolved shear stress did not change with the concentration of the stearic acid solution; however, the extents and slopes of Stages I and II were affected greatly. The observations lend evidence that the weakening effect of surface-active agents is controlled by the rate of desorption of the metal soap formed by the reaction of the surface-active agent and the metal surface. IT has been shown by various investigators1-" that surface-active agents markedly affect the mechanical properties of single crystals. (A surface-active agent, for the purpose of this report, is defined as a long-chain organic molecule which contains one or more polar groups. Usually, however, investigations have considered only molecules having one polar group.) In general, when single crystals are deformed in some solutions containing surface-active agents, the creep rate, Fig. 1, is increased and the yield strength is decreased. The fatigue strength has been reported to be affected also.ll Rehbinder and his asociatesl' explained the "weakening" effect of surface-active agents in terms of physical adsorption. They assumed that a large pressure was created in microcracks which existed on the surface of the crystal." Harper and Cottrell,' from their study of the effects of surface conditions, found that the deformation characteristics of zinc single crystals were not altered by a solution containing a surface-active agent unless the surface of the specimen had an oxidized surface. They concluded that the role of the polar molecule was to remove the strengthening effect of the oxide coating. Later, And-radeetBpresented additional evidence which appeared to agree with this conclusion. In contrast, Klinken-berg et al.7 reported data which confirmed the results of Rehbinder. Using zinc and cadmium crystals which had been cleaned by electrolytic polishing, a large increase in the creep rate was observed when Lle specimens were tested in a 1 pct oleic acid-paraffin oil solution. They also reported that the creep rate

Jan 1, 1962

By E. N. Aqua, C. M. Owens

The microstructure in cold-rolled Zircaloy-4 sheet has been characterized by transmission electron microscopy and X-ray diffraction line-broadening techniques. The rate of work hardening is measured in terms of microstrains, particle sizes, micro hardness, the tensile yield strength. The tensile yield strength of Prestrained (less than 10 pet) Zircaloy-4 sheet is found to be a linear function of the square root of the dislocation density, us predicted by work-hardening theories. ZIRCALOY is one of the most important structural alloys for nuclear reactor applications.''2 In order to understand the effects of the nuclear environment on Zircaloy structural members, the preirradiation microstructure must be characterized. This report will describe the substructure existing in cold-rolled Zircaloy-4 sheet as observed by electron microscopy and by X-ray diffractometry. I) EXPERIMENTAL PROCEDURE Commercial Zircaloy-4 strip was cold-rolled and annealed in argon at 760°C for 1 hr. The annealed sheet was again cold-rolled to a maximum of 50 pct reduction in thickness with segments of the strip being retained after 2.5, 5, 10, and 20 pct reductions. One-inch-square portions were chemically polished (50 parts HNO3, 50 parts H2O, 10 parts HF) and mounted onto lucite blocks using double-sided tape to prevent bending during handling. Thin foils suitable for transmission electron microscopy were prepared from each of the sheet samples. The sheets were mechanically polished through 600-grit paper to a 3 to 4 mil thickness and were chemically polished by immersion for 1 to 2 min in a solution containing: 50 parts HNO3, 50 parts H2O, and 10 parts HF, and rinsed in distilled water. The final metallographic procedure was to electropolish for less than 10 sec with an electrolyte of 10 parts perchloric acid and 90 parts glacial acetic acid, at 20 v, at room temperature using stainless-steel point cathodes and a vigorous stirring action. These foils were examined in a Philips EM 200 electron microscope using a 100-kv accelerating voltage.

Jan 1, 1968

By J. A. Norden

MUCH has been written concerning the hoisting equipment of various mines -throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable 'of handling about 1200 tons per day. It has not been worked, to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. 1. It is composed of three compartments, two of which are used for hoisting and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is; above the 700-ft. The. ore was-dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913, the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult, and slow process with the antiquated air hoist, so, in 1916, it was derided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year.

Jan 8, 1920

By John B. Baker, Bernard B. Betty, H. F. Moore

Fox several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.1,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. SPECIMENS The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.-The Bridgman method of casting single-crystal speci¬mens was used.3 The specimens were cast to the shape and size shown in Fig. I (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938