Search Documents

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman's arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman's paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman's work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"'. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan's blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations '-' of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin') apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder's Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time.

Jan 1, 1950

By Stephen Birch

LATOUCHE, or the Beatson plant of the Kennecott Copper Corpn., is located in the Prince William Sound district of Alaska about 80 miles west of Cordova and 60 miles from Seward. Ore was discovered and claims located on Latouche Island in July, 1897. The mines were worked in a desultory manner until 1910, when the property was acquired by the Kennecott Copper interests. The first shipment of ore was made in 1904; only the higher grade ore was mined and no attempt was made to treat the ore until it was taken over by the Kennecott, company. Since that time the mine has been developed to produce 1500 tons a day and a mill has been erected for treating this tonnage, using flotation entirely. The orebody is more or less lenticular in shape with a maximum width of about 280 ft. and a length of about 800 ft. The southern end of the lens is split by a horse of waste for about 400 ft. The hanging-wall limit is a well-defined fault associated with a band of pyrrhotite, having an average dip of 60°. There is no defined foot wall, the value of the ore governing the limits of the mining; in one part of the mine, however, it is defined by a minor fault. The orebody is located in a shear zone of the country rock of graywacke and slate. The principal mineral is chalcopyrite associated with pyrite and quartz. The mine is located a few hundred feet from tidewater; the mill is located on the beach and the ore is hoisted direct from the mine through a vertical shaft into the mill bins. Until the past year practically all the mining had been conducted in open pits. During the past two years, the ore above the 200-ft. level has been developed and a system of stoping devised to recover this ore; however, this system has not been in use long enough to give any definite results as to costs or efficiency. It consists, principally, of dividing the orebody into stopes, across the full width of the orebody, 70 ft. wide with a pillar 30 ft. wide between the stopes. Raises are driven through the stopes at intervals of about 60 ft. and all the ore is broken by drilling from these raises; in other words, similar to a shrinkage stope, doing the drilling from the raises instead of setting up on the broken ore as is customary. The ground is very much broken up by clay slips and seams running in every direction. Shrinkage stoping had been

Jan 1, 1924

By S. F. Radtke, J. A. Snyder, R. M. Scriver

An automatic, continuous casting arc furnace employing a nonconsum-able electrode and a direct current arc has been constructed and operated successfully for titanium. A comparison of the properties of arc and induction-melted titanium indicates that where high ductility, formability, and toughness are required, arc-melted metal is preferable. BECAUSE of the reactivity of titanium metal with all known refractories and the common atmospheric gases, melting of the metal presents numerous problems. It is necessary to provide an inert atmosphere in the furnace as well as a crucible material that will not react with the molten metal, if a ductile ingot is to be produced. Two special furnaces have been developed that meet the requirements and one, the induction heated graphite furnace, has been described in some detail.' Little information is available for sizable units wherein power is applied to the melt through an arc, and the dearth of technical information on such a furnace prompted this report. It has been demonstrated clearly that arc melting produces titanium metal with superior toughness, ductility, and formability. To produce titanium ingots with these properties, an automatic, continuous casting arc furnace has been developed and is described herein. The history of arc melting may be traced to 1800, when Sir Humphrey Davy2 first experimented with Volta's electric battery and found that light could be produced and an arc formed between two carbon points attached to the cell. The discovery of the arc was followed by the design and construction of an arc furnace by Napier," in 1845, for the reduction of metal oxides. In 1853, Pichou' described a similar furnace, although it was not until the discovery of the dynamo in 1867 that the arc furnace could achieve commercial significance. In 1878, Siemens- esigned the first arc furnace intended for the melting of metals and by 1882 had melted steel and platinum successfully. . This was followed by Moissan's" classical work with the arc furnace in 1892. W. von Bolton,' in 1905, found that the arc furnace was suited admirably for melting refractory metals. In his work with tantalum, no suitable refractories for retaining the molten metal were found to exist. Together with Otto Simpson, he developed an arc furnace with a water-cooled copper crucible in which tantalum could be melted without contamination. This technique proved eminently successful. In his paper on the preparation of ductile titanium, Krolle first described an application of the von Bolton furnace to the melting of this metal. The

Jan 1, 1952

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By W. A. Griffith

The fundamental principles and modern techniques of experimental planning and data analysis, applicable to any type of research, are particularly important in flotation experimentation. Since they constitute the modern science of experimentation, they should be among the working tools of any scientist, research engineer, or plant operator engaged in flotation investigates. This chapter is a review of these principles and techniques. Equipment and procedures for the actual conduct of experiments will not be discussed here since these subjects are well covered elsewhere in this volume. Neither will any attempt be made to impart a working knowledge of statistical methods of data analysis since this would be impossible in the space allotted, and many excellent texts are available to the diligent inestigator.1-4 The objective here is simply to interest the reader in the application of statistical techniques to flotation experimentation by illustrating their utility in situations frequently encountered, and to point out the principles of experimental planning necessary for their proper use. Any conscientious metallurgist engaged in flotation experimentation or operations is well aware of the inherent complexity of the flotation process, and of the often frustrating difficulties this introduces into experimentation. The raw materials normally treated by the process are complex both physi- cally and chemically, and often highly variable even when from the same source. The flotation process itself is characterized by a very large number of potentially important process variables. Many of these are beyond the con- trol of the metallurgist, and some cannot even be measured quantitatively with available instruments. Those which can be measured and controlled with reasonable precision often produce effects which are intricately interrelated. Not only are the variables many, but the physical and chemical mechanisms by which they function are imperfectly under stood. To compound the difficulty, experimental techniques are relatively crude. Controls are not very precise, and the human factor looms large in most flotation experiments. These situations lead inevitably to experimental data of a relatively low degree of precision or reproducibility. Some are inclined to think that these conditions are unique to flotation experimentation. They are not. The experimental problems met by the agronomist, the biologist, the social scientist, and others are equally complex. Investigators in these fields pioneered in the development of methods for handling just such situations by proper experimental planning and the application of statistical methods in the analysis of data. Their pioneering work has grown into a well established modern science of experimentation which has spread into every field of science. This science is based upon statistical

Jan 1, 1962

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By Andrew Mayer

EARLY in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. L. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense Plant Corporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at 10,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. THE PROCESS The process, in brief, is as follows: The raw materials are dolomite and ferrosilicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to the reaction 2(MgO, CaO) + Si = 2Mg + 2CaO, SiO2 It is distilled from the charge and condensed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of ±. tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. CHOOSING THE SITE The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. In the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO

Jan 1, 1944

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943

The Joint Session on Continuous Cast- ing, of the Institute of Metals Division and the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers, convened in the Jade Room of, the Hotel Waldorf-Astoria, New York City, on Feb. 23, 1944, at 9:15 o'clock, Carl E. Swartz presiding. C. E. SWARTZ.-It is gratifying to see so many out at what may seem an early hour for the beginning of A.I.M.E. sessions, but I think this number-some fifty or sixty of you-is an adequate expression of the interest in these processes all over the United States, and possibly in foreign countries. I would like to ask those who feel that this type of program is of value to you to write or speak to some one of the Institute of Metals Division officers and suggest other topics for symposiums. We have a feeling that some of these current practices are of interest and we believe that under proper sponsorship many of the companies will be willing to give publicity to processes such as those that will be discussed today. Also, we would like suggestions and criticisms, so that the next ones can be better. The subject of continuous casting is not new, of course. The two papers on the program this morning will adequately cover the history and some of the earlier processes, some of the theory and some of the practice, some of the reasons why these various methods did not work. I was rather interested in discovering, when thumbing through one of the A.I.M.E. publications the other night, an article on continuous casting. I was not aware that the A.I.M.E. had published any papers on continuous casting, but there may be a number. The one that I happened to find was published in the 1915 volume, on the Mellen rod- casting process, and so we might say this is not the first session in which these subjects have been under discussion. However, there have been many improvements since then in all fields of metallurgical and mechanical engineering; consequently, I think that the papers today will be a little more involved and a little more complete in their technique. The first paper today will be given by one of our gentlemen of the press, who has done one of the outstanding jobs in this country in calling to our attention some of the newer processes that are being considered and being used in the metallurgical indus-

Jan 1, 1945

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

By Alfred Fisher

CONSERVATION of mine timber is becoming in-creasingly important, and the consumer is en-couraged to use treated wood to permit longer life of mine timbers, and attempts are also made to substitute other material for wood. The great diffi-culty in substituting metal and concrete props for wood is the inability of these to give yielding resistance to roof pressure as wood supports do. In Europe, where mine timber costs are somewhat more important than in America, many designs of steel props have been tried, but have been unsuccessful, chiefly on account of inability to give yielding resistances. A metal pit prop that gives the desired effect has been extensively used in European mines and has caused a considerable reduction in accidents from falls of roof. Where mining operations have been sus-pended on account of strikes, conditions were found to be much better where such props were used instead of wood props, and machinery, which would have been destroyed by roof falls had wood props been used, was protected by the use of these yielding metal props. As this prop is adjustable, all the work of adjusting and transferring long props through narrow ways is done away with. It can also be drawn with greater ease and safety than wooden props; when properly used it is practically indestructible. European users have reported savings as against wooden props as high as 80 per cent. It gives audible warning of its working because the sliding action takes place in minute jerks. As the prop yields gradually to pressure its force is taken up by friction between the H sections, and this movement progressively increases the resistance of the prop to the increasing roof pressure. In the early development of the prop, it was designed with two steel members a and b of standard H steel sec-tions of equal dimensions provided with guide claws a' and b', held in frictional contact against each other by two differential wedges, f and g, and a floating link, e. In setting up the prop its two members are drawn out to the required length, the loose wedge, g, is then fitted into the space between the left-hand roller of the link d and the lower member of the prop b, and tapped suf-ficiently tight to prevent any relative movement of the two members from taking place prematurely. The prop is then raised to its intended position and secured in the usual way.

Jan 8, 1927

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By E. C. Pechin

Secretary's Note.—Mr. Bramwell was born in 1846, at Liverpool, England, his father being English, and his mother American, of Scotch ancestry. Brought to the United States in early childhood, he was educated at the public schools and graduated from the College of the City of New York. He subsequently studied his profession as a mining engineer at the Royal School of Mines, Berlin, Prussia, and was for a short time in the service of the Prussian government at Konigs hutte. Returning to this country in 1871, he was employed during succeeding years as mining engineer, chemist, and manager at various fnrnaces and iron works in Pennsylvania and the Southern States until, in 1883, he became actively engaged in the development of the Flat-Top coal-field of southwestern Virginia, in which region the town of Bramwell was named after him, in recognition of his services as a pioneer of the great industry which he did so much to promote. After prolonged and fluctuating ill-health, he died, July 13, 1894, at Paris, France. At the opening session of the Bridgeport meeting, the Secretary announced his death, and Mr. Pechin, being called upon, made the remarks reported below.— R. W. R. Widely as Joseph Herbert Bramwell was known, I. think I knew him somewhat better than any one else. After finishing his studies abroad, he came to this country, a very young man, seeking an engagement. This was about the beginning of 1871, as I remem ber, and I was then trying to make iron at Dunbar, at the foot of the Allegheny mountains, in Fayette county, Pa. His engaging manner and charming personnel, combined with his letters of intro duction, made me more than satisfied in securing his services as my chemist. At the outset we lived a sort of pioneer life, and for many months he was practically a member of my family, and the affection then formed remained unbroken to his dying day. I vividly recall the circular of April, 1871, signed by Eckley B. Coxe, R. P. Rothwell and Martin Coryell suggesting a meeting at Wilkes-Barre, Pa., for the purpose of forming the American Institute of Mining Engineers. At the last moment, prevented from going, I sent Bramwell; and I am more than glad that his name appears among those whose sagacity established an Institute that has become illustrious by reason of its numbers, the character of its members, its invaluable papers and its enormous influence for good

Jan 1, 1895

ON JUNE 7 the German Government handed to the French and Belgians a new proposal for reparations, which offered 1,200,000,000 gold marks annually, to be guaranteed as to 500,000,000 by a mortgage on the national railways, as to another 500,000,000 by a mortgage on industry, commerce, land and factories, and as to 200,000,000 by a luxury tax. The number of years for which this payment should run to be left to settlement by an international conference. This offer was taken under consideration by the French and Belgians, who instituted conversa-tions with the British in the hope of arriving, at some joint action with respect to the Germans. Up to the end of June nothing had been determined. In the meanwhile, the continued French and Belgian occupation of the Ruhr seemed to develop a condition of guerilla warfare, considerable bloodshed occurring throughout the region. The second Lausanne Conference dragged on, the Allies being apparently unable to take any firm, joint stand, while the Turks increased their importunities and managed to get concession after concession. Early in June a revolution occurred in Bulgaria, the previous Government under Premier Stambulisky, based on the agrarian party, being forcibly thrown out by a bourgeois and military combination. This pro-duced considerable disorder in Bulgaria, outside of which country the nature and purpose of the revolution does not appear to be well understood. Stambulisky's partisans offered feeble, isolated resistance to the revolu-tion; in connection with which there was some blood-shed and Stambulisky himself was reported killed, although this was later contradicted. Professor Zan-kof, the new Premier, issued a statement, that the change of the Government was the result of discontent, that the foreign policy of the new Government would be peaceful, and that Bulgaria would continue to fulfill her international obligations, particularly the treaty of Neuilly. It was the opinion of London that the immu-nity from taxation enjoyed by the farmers under the agrarian regime is likely to he superseded by more equi-table taxation, and in general that the bourgeoisie will be better administrators of the public affairs In domestic affairs industrial activity continued at a high rate, but there was distinct relaxation in the demand for raw materials, and also in some manufac-tured goods. During June there were reductions of prices by many of the automobile tire manufacturers. There seemed to be also further contraction in the demand for automobiles.

Jan 6, 1923