Search Documents

By Stephen Birch

Latouche, or the Beatson plant of the Kennecott Copper Corpn., is located in the Prince William Sound district of Alaska about 80 miles west of Cordova and 60 miles from Seward. Ore was discovered and claims located on Latouche Island in July, 1897. The mines were worked in a desultory manner until 1910, when the property was acquired by the Kennecott Copper interests. The first shipment of ore was made in 1904; only the higher grade ore was mined and no attempt was made to treat the ore until it was taken over by the Kennecott company. Since that time the mine has been developed to produce 1500 tons a day and a mill has been erected for treating this tonnage, using flotation entirely. The orebody is more or less lenticular in shape with a maximum width of about 280 ft. and a length of about 800 ft. The southern end of the lens is split by a horse of waste for about 400 ft. The hanging-wall limit is a well-defined fault associated with a band of pyrrhotite, having an average dip of 60". There is no defined foot wall, the value of the ore governing the limits of the mining; in one part of the mine, however, it is defined by a minorfault. The orebody is in a shear zone of the country rock of graywacke and slate. The principal mineral is chalcopyrite associated with pyrite and quartz. The mine is situated a few hundred feet from tidewater; the mill is on the beach and the ore is hoisted direct from the mine through a vertical shaft into the mill bins. Until the past year practically all the mining had been conducted in open pits. During the past two years, the ore above the 200-ft. level has been developed and a system of stoping devised to recover this ore; however, this system has not been in use long enough to give any definite results as to costs or efficiency. It consists, principally, of dividing the orebody into stopes, across the full width of the orebody, 70 ft. wide with a pillar 30 ft. wide between the stopes. Raises are driven through the stopes at intervals of about 60 ft. and all the ore is broken by drilling from these raises; in other words, similar to a shrinkage stope, doing the drilling from the raises instead of setting up on the broken ore as is customary. The ground is very much broken up by clay slips and seams running in every direction. Shrinkage stoping had been

Jan 1, 1925

By R. J. Miller, W. A. Bates

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neilll observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in inter-granular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle3 in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1942

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By Horace Pops

Isothermal sections in the copper -rich region of the Cu-Si-Zn a1by system have been determined at 8473 760; 6003 and 482°C by means of microscopic examination with confirmatory X-ray diffraction work. The stability of the bee 0 phase decreases both with decreasing temperature and with increasing copper content. The silicon-n&apos;ch 0 phase decomposes upon quenching from high temperatures either by a martensitic or by a "massive" transformation, depending upon the solute content. A two-phase equilibrium is found to exist in the Cu-Si-Zn system between the hep < phase of the Cu-Si system and the bee ß phase of the Cu-Zn system. It is shown that the isothermal limits of the primary solid solution at 760; 6003 and 482°C are in part affected by the intermediate phases which follow them in the ternary system Possible electron-concentration and size effects upon phase boundaries are discussed. ALTHOUGH the mechanical and physical properties of silicon brasses have been measured in great detail, the factors which influence these properties are not well-understood, partly because the knowledge of the phase relationships in the Cu-Si-Zn system is limited. Gould and Ray1 studied the effects of silicon upon the hardness and structure of Cu-15 pet Zn and Cu-40 pet Zn alloys. They proposed an isothermal section at 800°C which was not based upon experimental data, since the binary phase diagrams had not been completely determined. Using Cu-Si-Zn alloys containing approximately 5 wt pet Si, vaders2 determined the boundary, at 750°C, between the copper-rich solid solution and an unidentified second phase. Masing and wallbaum3 examined a vertical section through the ternary diagram in the region between Cu-20 pet Zn and Cu-10 pet Si alloys, but they emphasized uncertainty about their data. Mima and Hasegawa4 studied the liquidus surface of Cu-Si-Zn alloys, phase transformations in high silicon-bearing (20 to 25 at. pet) alloys,5 and the phase relations in low silicon-bearing Cu-Si-Zn alloys.6 Their experiments were based upon thermal analyses and metallographic observations. The compositions of the phase boundaries were not determined with high precision, and the crystal structures of the phases were not reported. Because of uncertainties in the existing literature, it became of interest to determine more accurately the phase relations in copper-rich Cu-Si-Zn alloys. The crystal structures, stability, and phase boundaries of the primary solid solutions and several intermediate phases were determined, and the data are reported as partial isothermal sections.

Jan 1, 1964

Gentlemen.-The Institute was founded 54 years ago "with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained," At least once a year it is well to take stock of our assets, review our performance and determine how well we are now carrying out the purposes of our Founders. There can be no question as to the work the Institute has done and is doing in promoting the arts and sciences in the fields of mining and metallurgy. One needs only to contrast the methods, the labor and the costs of a half century ago with those now to visualize how far we have gone in the development of accurate technology and sound economics in mineral and metal production. The great mines, mills and smelters of the present, handling individually thousands of tons per day, would&apos; have been impossible except for the accumulation of knowledge, the development of theory, and the improvement in practice that has characterized the period since the foundation of the Institute. The United States has prospered in the last half century greatly, and this has been due not merely to the possession of great natural resources, but to these resources being reduced to possession and put to work. The absence of customs barriers and the freedom of trade across the whole width of this great continent has been an important factor in the growth of our wealth. Unrestricted interchange of goods has permitted each citizen to draw on the resources of the whole country. However, these are but subsidiary causes of prosperity. The free interchange of scientific and technical data, by making the whole body of facts and theory available to each worker, has made this quick and unrivaled development possible. In promoting this free trade in knowledge the Institute may claim a large place without fear of denial. The .72 volumes of TRANSACTIONS, the special volumes, the bulletins and the other publications that have been issued, include a store of knowledge of the arts and sciences related to the production and use of metals and minerals not duplicated elsewhere. The large list of foreign members-1746 in number-few of whom ever have opportunity to attend meetings and all of whom derive their main benefits from membership through the pub-

Jan 1, 1928

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.&apos; At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.&apos; They investigated the inflammability of certain magnesium alloys. Brown3-&apos; reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.&apos; These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By Max Roseler

THE CHAIRMAN (WILLIAM KELLY, Vulcan, Mich.).-Some 8 or 9 years ago I was at Daiquiri, only a. few miles east of Firmeza, where there are deposits of iron ore of the same general character. There is a great conical hill, perhaps 800 or 1,000 ft. in height and the ore deposit appears to be somewhat in a canoe shape on one side of the hill. The mining has been done by quarrying the ore in benches. These are called levels and to go to the 10th level it was necessary to take mules and ride to the top of the hill, which was to me an upside down arrangement of numbering levels and a novel method of entering and viewing a mine. A little copper ore can be seen in places, and not being a geologist I thought the deposit might possibly be a gossan, but none of the geologists who have written on the subject approve of this hypothesis and the great question seems to be what part, if any, the limestones have played in the origin of ore; whether these deposits are replacements of limestone and whether they are contact ,deposits between the limestone and the other rocks. Examinations have been made by many eminent geologists and the problem has been discussed vigorously on both sides. The deposits are exceedingly interesting from a commercial standpoint and although they have been studied for a number off years the origin of the ore is still a difficult and somewhat controversial question. J. T. SINGEWALD, JR., Baltimore, Md.-I have had the privilege of visiting these deposits and have been very much interested in this paper, of Dr. Roesler&apos;s; having been on the ground, I can easily appreciate the difficulties under which he labored in attempting to work out the geology of that region, and he certainly deserves considerable credit for the way in which he has deciphered the geological relations of the Firmeza district. There are several points in his paper 1 ,would like to discuss; first, in regard to the geological interpretations. His differs from previous interpretations in the relative age of the diorite and the granite, but you will note that Prof. Lindgren suggests the probability. that those two rocks are very closely of the same age, and Prof. Kemp actually suggests, although he does not-accept the idea, that the granite is probably later than the diorite, so that there seems to be no particular reason

Jan 4, 1917

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O&apos;Neilll observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in inter-granular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle3 in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1942

By L. R. Blair

Many hydrated silicates have been synthesized and sold for commercial use. However, this paper discusses only hydrated calcium silicates and, to a lesser extent, hydrated magnesium silicates. Synthetic calcium silicates were first formed by man when he found that mixtures of silica or silicates and lime in water set up to form cements. The material which was responsible for the cementing properties was calcium silicate hydrate, although this fact was not recognized until early in this century. In the early 19001s, synthetic calcium silicates, reinforced with fibers and formed simply by reacting calcium hydroxide and silica in water with fiber at atmospheric or under low pressure autoclave conditions, found increased use in thermal insulations and in building products. These insulations were found to have a low thermal conductivity and would withstand temperatures up to 650°C. This, combined with their very low densities (from 8 to 50 Ib per cu ft) and fairly high strength, also made them suitable for use as building products. Following the disastrous Morro Castle fire of the 1930Js, calcium silicate board products were used as partitioning material in all shipboard construction in the U.S. As autoclaving techniques were improved and developed, it was: learned that under hydrothermal conditions new and useful calcium silicates which could be used under more extreme temperatures (up to 980&apos; C) could be prepared. These had high surface areas and other unique properties which suited them for use as fillers, pesticide carriers, low temperature insulating materials, and adsorbents for the removal of fatty acids from various solutions. Hydrated magnesium silicates have not been studied as extensively as the calcium compounds. Their first important use was in the filtration of dry cleaning solutions for the removal of fatty acids. With the introduction of detergents, it was found that these products lost their advantage because of their high affinity for the detergent chemicals. However, in recent years these chemicals are finding increasing use as decolorizing agents for fats and anti-caking agents for resins. Some materials with very high surface are finding new use as adsorbents. CALCIUM SILICATE HYDRATE COMPOUNDS AND THElR CONDITIONS OF FORMATION Within the past ten years much has been done in the field of calcium silicate hydrate chemistry. As a result of this work it has been found that at least 25 different forms of calcium silicate hydrate can either be formed synthetically or found as naturally occurring materials. The stability and composition relationships among these 25 compounds present a very complicated picture, and many of these very closely resemble other forms and are difficult to dis-

Jan 1, 1962

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.&apos; In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943