Search Documents

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By B. A. Cheadle, C. E. Ells

The ovienlalion of hexagonal a-zirconium crystals in cold-drawn Zircaloy-2 tubes and in both as-extruded and heat-treated Zr-2.5 wt pcl ND tubes has been rrleasured using the inverse Pole - figure technique. Uniaxial tensile tests hare shown the Zil-caloy-2 lubes to hare highly anisotropic delovmation behavior whereas heat-treated Zr-2.5 wt pet Nb tubes are nearly isotropic. The differences in deformation behavior are esbloilred from the observed textures of the tubes and the deformation systems known to oberate in Zircnloy,-3. Tlze vcsults lead to an explanation of the high effective strain observed fov the Zircaloy-2 tubes as colrzpared to heat-treated Zr-2.5 wt pet Nb tubes in restrained end burst tests at 280° to 300°C. THE Zr-2.5 wt pct Nb alloy. when heat-treated by quenching from temperatures slightly below the (a + p)/P phase boundary and subsequently aged at 500°C, has tensile strengths about 50 pct greater than those of 20 pct cold-worked Zircaloy-2.1 There is. therefore, considerable economic incentive to replace Zircaloy-2 with the heat-treated alloy in some in-reactor applications. notably for pressure tubes, where strength is a prime consideration. However, when tubes of Zr-2.5 wt pct Nb fabricated by extrusion and drawing prior to heat treatment were subjected to restrained end-burst tests at 300 °C. the circumferential expansion at failure1 was only 10 pct that of cold-drawn Zircaloy-2 tubes in similar tests,2 Table I. This result was not predicted from uniaxial tensile tests in which the ductilities of the two materials were quite similar.' The detailed requirement for ductility in pressure vessels has not yet been worked out. and comparison of the relative merits of cold-worked Zircaloy-2 and heat-treated Zr-2.5 wt pct Nb is further complicated by the irradiation-induced loss of ductility and hydrogen pickup each will undergo from reactor operation.1,2 Nevertheless. the lower circumferential expansion of the Zr-2.5 wt pct Nb tubes raised serious doubts on the advisability of their use as pressure vessels. For this reason, an investigation to determine the cause for different ductilities of the two types of tubes was initiated. From a study of uniaxial tensile properties and crystallographic orientation it has been found that the fracture ductilities observed in the burst tests can be related directly to the crystallographic ori-

Jan 1, 1965

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By Alexander Coucoulas

FABRICATION of thin-film circuits deposited on glass substrates requires the formation of permanent electrical contacts. Since thin films are in the order of a few thousand angstroms thick and are deposited on nonconductive surfaces such as glass, new methods of lead attachment are being pursued in the microelectronics industry. Ultrasonic welding is being considered in thin-film technology since joining can be accomplished between a wide variety of dissimilar materials.l,' Ultrasonic welding is accomplished by a transducer-coupling-tip system which converts high-frequency electrical energy into mechanical vibrations and delivers it into the weld region. During the process the tip oscillates in a direction parallel to the surface of the weldments, inducing shear stresses in the work pieces which are clamped between the tip and anvil. Though the basic bonding mechanism is not clearly understood, it has been described as closely akin to friction welding. In the course of an investigation concerned with ultrasonic we!ding of aluminum wires to tantalum thin films (1400A) deposited on glass, low weld strengths were related to glass failure. Upon investigating this condition, an improved method of bonding was developed where the aluminum was held at a temperature where a minimum amount of strain hardening occurred during the introduction of ultrasonic energy. Experimental Procedure. Aluminum wires (0.015 in,) were bonded to tantalum thin films with an optimized set of welding parameters (power, time, clamping force) employing a commercial 100-w 60-kc ultrasonic welder. Forty-five degree shear-peel tests, where the lead is pulled at a 45-deg angle with respect to the substrate at 0.2 in. per min, produced a large variation from zero to the strength of the wire, Table I. Inspection of the weld region generally revealed: glass cracking before and after testing; the removal of glass nuggets from the substrate by the lead during testing, Table I; thin-film penetration. In an effort to improve the shear-peel strength, the aluminum between the tip and substrate was heated above ambient temperature through an argon gas media prior to and during welding with the same parameters employed above. With the addition of heat: wire deformation was increased; shear-peel tests all failed at the weld-wire junction, leaving the bonded portion undisturbed; no evidence of glass cracking or film penetration prior to or after testing was observed. In order to prevent failure at the weld-wire junction due to excessive wire deformation, 0.035-in. aluminum wires were welded to tantalum thin films with an optimized set of welding and heating parameters. As

Jan 1, 1967

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A' ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed' he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,' in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objection- able to the buyer. It is still extensively practiced on the plus 1-in. sizes, and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for efficient hand picking. At most mines an attempt is made to remove the visual impurities at one or more of the following places in the surface plant:2 (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors;. (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each-piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not 'exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and-rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft, in width, so that a picker on either side will be able to remove impurities from the center of

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By Howard Thompson, H. N. Hall, Frank Nuss

Removal of bit cuttings is an important function of drilling muds. In an effort to obtain better understanding of the factors influencing the removal of cuttings, an extensive series of laboratory tests were made in which slip velocities of various sizes and shapes of particles were measured in muds of different physical properties. Empirical equations were then derived from these experimental data. These equations show that slip velocity is dependent on cutting size and shape, mud flow constants, and flow state of the mud. Applicability of these equations for field use is demonstrated by comparing computed slip velocities with slip velocities obtained from field tests. Drilling muds have many functions, but perhaps the most important is the removal of bit cuttings from the well. In a 10,000-ft well, the weight of rock which is drilled and must be carried to the surface is over 150 tons. In addition to this, the mud must remove any sloughings from the well bore. Failure of the mud to promptly remove either bit cuttings or sloughs from the well bore causes re-drilling and excessive wear on bit teeth, slows down drilling rate thereby increasing well costs, and greatly increases possibilities for stuck drill pipe when circulation is stopped for any length of time. Drilling muds lift bit cuttings to the surface by means of the upward velocity of the drilling mud in the annulus. Because a density difference exists between the rock being drilled and the drilling mud, there is a difference between mud velocity and the rate of bit cutting travel, called the net rise velocity. To evaluate the ability of any type of drilling mud in respect to lifting cuttings, some method must be known for predicting the rate of fall of cuttings through mud traveling upwards in the annulus. Equations for the rate of fall of particles through a true fluid have been satisfactorily determined by several authors. 1-6 Since drilling muds are not true fluids, but obey the laws of Bing-ham,7 it should not be expected that equations for rate of fall of cuttings in a true fluid would be applicable to plastic fluids such as drilling muds. Several authors have attempted to compute cutting slip velocities in muds using a viscosity value obtained with a Stormer viscosimeter; however, unsatisfactory results were obtained. Pigott8 took cognizance of the phenomenon of variation of viscosity with velocity in laminar Row, and calculated laminar slip velocities using a variable viscosity with Stokes law, and turbulent slip velocities using Rittingers law. Drilling muds obey the laws of plastic flow which involve factors not affect-

Jan 1, 1950

By William J. Harris, Morris Cohen

INTRODUCTION THE recent application of lineal analysis1,2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at [M.] and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as "a lowering of [M.], resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (Th) for a sufficient period of time, more austenite may be retained at a given lower or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th, is measured explicitly in terms of the excess austenite [(S)] that exists in the steel at Tr, over and above the amount that is normally present after direct quenching to Tr. Tr is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (Th) may be above or below [M], and still cause stabilization depending upon the chemistry of the austenite. Stabilization has been found to occur in the presence of bainite4 and of martensite5,6,7,8 as well as in the absence of either.9 The phenomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at Th that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subsequent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6.8 low alloy 6.7.8 and high alloy tool steels.10,5 Starting with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1948

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera', the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles' Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By Lester L. Hirst, Arno C. Fieldner, Henry H. Storch

EXPERIMENTAL work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogenation of bituminous coal and tar by the Bergius-.I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 lb. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydrogenation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. EQUIPMENT AND GENERAL PROCEDURE OF RESEARCH The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera', the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles' Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By J. M. Schopt

COAL petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petro-graphic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities* of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures. The empirical and comparative character of standard chemical coal analytic values is one of the consequences resulting from heterogeneity and insolubility of coal. Nevertheless, these coal analytic methods are highly technical and diversified. Coal petrol.ogy employs a group of similar analytical methods which provide information about coal that the other methods cannot supply. The heterogeneity of coal is most clearly demonstrated by means of petrologic studies. The properties utilized in coal petrologic studies are related to texture (size, form, and association), hardness, light reflectance, and light absorption and transmission (color). Size relations are most evident but are commonly overlooked. Coal is classed chemically as a mixture, and chemical analyses thus show the composition of the sample as a whole. Geologically coal is an organic clastic deposit, derived from diverse plant fragments and particles having a size range comparable to that of a conglomerate or breccia. The mixture of different materials that compose coal, large and small, can be realized only by microscopic study. This is because the fundamental cellular units of plants, from which coal is formed, are microscopic in size. The kinds of altered plant particles and fragments in coal have specific differences in hardness, reflectance, and color that signify differences in composition. These differences must be taken into account in evaluating the aggregate properties of coal. Terminology and Texture Full discussion of terms applied by various petro-logists in analysis of coal is beyond the scope of this article. For convenience the simpler types of petrologic entities that are defined without reference to lithologic occurrence or texture will be called coal components. Fig. 1 lists reactive and relatively inert

Jan 1, 1957

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948