Search Documents

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley's con alusions. These amrrmptions are: that 'the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley's paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss 'by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By D. W. Fuerstenau, L. M. Berlioz

In 1957, Charles1 first presented an analysis of a relationship between the energy expended in comminution and the extent of size reduction achieved. Subsequently, Schuhmann extended and interpreted Charles' approach to comminution. According to their analysis, the energy, E, expended in comminuting unit mass of fairly uniformly-sized material is related to the size modulus of the product, k, by where a is the distribution modulus (slope of the log-log cumulative size distribution plot) and C is a constant, which is primarily determined by properties of the solid. If there is any fundamental basis for the E vs k relationship, E must necessarily be concerned with the useful work for the size reduction process and not necessarily the work input, as discussed in detail by Harris.3 Charles and numerous other investigators tested this equation only by relating k to the grinding time, assuming expended energy to be directly proportional to time, but never directly measuring power. In our laboratories, we recently constructed a special batch ball mill with which the power could be accurately determined with torque measuring apparatus.4 With this device, a direct test of the Charles relationship could then be made for ball milling. 5 EXPERIMENTAL A stainless steel mill, 11.5 in. long and 10 in. in inside diam, lined with eight low-silhouette lifter bars, was used for these experiments. The grinding media consisted of 30 kg of single sized, 1-in. diam, stainless steel balls, which occupied about 50% of the total mill volume under static conditions. The void fraction of the static ball load was approximately 0.4, and for the dry grinding conditions used, the corresponding interstitial volume was filled when about 3300 g of the dolomite feed material was present. The 7x9 mesh dolomite used as feed was obtained as a natural, uncrushed product thus as- suring a random distribution of feed particle shapes. Charge weights of 660, 1320, 1980, 2480, 3300, 3960 and 5280 g, which correspond to 20%, 40%, 60%, 80%, l00%, 120%, and 160% of the interstitial load, respectively, were used. Grinding times of 20, 40, 60, 80, 100, 150, 200 and 300 revolutions were considered, with the mill operating at 54 rpm (approximately 60% of critical speed). The tests were made sequentially, in that the size distribution obtained after a certain grinding interval was utilized as the feed for the subsequent period of grinding. Agreement with control experiments where the mill ran continuously for the entire interval was excellent. Torque measurements were made utilizing a Baldwin-Lima-Hamilton SR-4 torque pickup in the manner that has been described previously.3 Standard wet (to obtain the -400 mesh material) and dry sieving procedures were followed using the Tyler full screen series. RESULTS The Gaudin-Schuhmann size distributions obtained in all of these experiments are characterized by distribution moduli (slopes), a, of about 0.66 and are representative of normal dry batch ball milling of a material like dolomite. As an illustration of typical

Jan 1, 1968

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 9144 m (30,000 ft) is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed in Table 1. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of international Minerals and Chemicals Corp. and Halliburton Co.); and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, WY. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market. Function of Drilling Fluids In the early days of rotary drilling, the primary function of drilling fluids was to bring the cuttings from the bottom of the hole to the surface. Today it is recognized the drilling fluid has at least ten important functions: 1) To remove the cuttings from the bottom of the hole and carry them to the surface. 2) To cool and lubricate the drill string and drill bit. 3) To build an impermeable cake on the wall of the hole. 4) To control subsurface pressures. 5) To hold cuttings and weight material in suspension when circulation is interrupted. 6) To release sand and cuttings at the surface. 7) To support part of the weight of drill pipe and casing. 8) To reduce to a minimum any adverse effects upon the formation adjacent to the hole. 9) To insure maximum information about the formation penetrated. 10) To transmit hydraulic horsepower to the bit. In order to accomplish some or all of these functions while penetrating formations of various characteristics, several types of drilling fluids systems have been designed. Types of Drilling Muds There are two basic drilling fluid systems-water-base muds and oil-base muds. There is a wide variety of groups within these two main

Jan 1, 1983

During the past 60 or 90 days, the metropolitan newspapers have published much concerning unemployment throughout the nation and the efforts of the Army and various other bureaus for finding work for the returning soldiers. The United States Employment Service has 2000 bureaus throughout the country, which Nathan A. Smyth, Assistant Federal Director, states have placed more than 2,400,000 persons in employment. The Engineering Societies Employment Bureau, which, since December, 1918, has been endeavoring to put all returning engineers in touch with employers who need efficient men, has produced results that are very gratifying to the Secretaries of the four Founder Societies under whose direct management the Bureau operates. During this period, 1615 men have registered at the Bureau's office in the Engineering Societies Building; not all of these, however, are unemployed. Many are ex-army and navy men, who in passing through New York on their way home, look over the field in the hope of making a change for their own benefit before returning to their former positions. During this period, 427 positions vacant have been filed, 2300 of which positions have been filled from the men registered. The letters mailed by this Bureau amount to about 1000 a month and the number of personal calls at the office, 1600. The lowest number of positions filled has been in mining, but the lowest number of registrations is also from mining men. While in February idleness throughout the nation was increasing at the rate of 35,000 a week, under date of Mar. 7, Arthur Woods, a special assistant to Secretary of War Baker, states that there is a material improvement in the unemployment situation and that the problem is no longer a serious one. It is recognized that' the improvement wrought in each individual by his military training and experience has so increased his value that it is 'not only unfair, to ask these men to accept their old jobs at the old wages, but it is probably very unlikely that they will be willing to do so. This plain statement of improvement may not carry conviction to everyone but a concrete example will show its validity. Take the example of a young man under 21, bright and intelligent, with only a high-school education who was employed, before being drafted, on purely manual labor. He shows up well under military training and is made a corporal; he makes good and is appointed a sergeant; and finally becomes top sergeant, which requires him in many ways to handle the entire company of 250 men. The result is; even if he has not been tried by the fire of battle, he comes out of the army with a feeling of self-confidence and capacity that was entirely lacking when he went in and he has had actual experience in handling a larger body of men than the average mine foreman at twice his age, and he has had twice the average amount of detail work to take care of.

Jan 4, 1919

By G. H. Matheson, J. M. W. Mackenzie

The coal concentrates studied contained clay slimes which would not flocculate on the addition of a polymer flocculent alone. The mechanism of the flocculation process is interpreted on the basis of the flocculation of lyophobic colloids. The filtration rate characteristics are shown to deviate slightly from certain basic filtration equations. Cake moisture was shown to decrease with cake drying time and vacuum, and increase with cake thickness. Filtration is a commonly accepted method of dewa-tering the fine coal concentrates produced in coal cleaning operations. Dewatering of these concentrates, using drum or disc vacuum filters, usually presents few technical difficulties and will result in the production of a filter cake containing some 20 to 25 pct moisture. In many coal cleaning operations it is common practice to add flocculants to the coal concentrates prior to filtration to increase the filtration rate. The mechanism whereby flocculation increases filtration rate has been summarized by Gaudin,4 while Geer, et a15 have compared the effectiveness of starch and synthetic flocculants as filter aids for a variety of coal concentrates. Coal concentrates, containing appreciable quantities of expanding lattice clays of the montmorillonite-illite group, sometimes prove impossible to filter without flocculation of the pulp prior to filtration. The fine coal concentrates produced at the Newcastle washery of The Broken Hill Proprietary Co. Ltd. fall into this group. Coals mined in this district contain appreciable quantities of expanding lattice clays which break down in the washery circuit waters and, by processes of mechanical inclusion, contaminate the coal concentrate thickener feed. Despite the classifying action of this thickener, the underflow which is pumped to the filters contains sufficient clay slimes to render filtration of the unflocculated pulp impossible. Filtration leaf and plant tests were carried out to develop effective and economic flocculant combinations and to determine the filtration characteristics of the flocculated coal concentrates. The determination, by leaf testing, of the filtration characteristics, and the analysis of these characteristics in the light of the equations of Brown2 resulted in the successful trial operation of the filters in the Newcastle washq. Although the filtration characteristics are not entirely in agreement with the theoretical treatment of Brown, the equations developed made it possible to predict, from leaf tests, the effect in the plant filters of pulp density, form vacuum, and form time on filtration rate and filtrate volume. EXPERIMENTAL PROCEDURES The sample used for leaf testing was the coal concentrate thickener underflow, which in plant operations would form the feed to the two 12-disk Dorr-Oliver filters. The feed to the coal concentrate thickener comprises the undersize produced by dewatering the Diester table concentrate on 5-mm dewatering screens and the overflow produced by cycloning of the froth flotation concentrate. At the time of testing these filters were inoperative because of the difficulties in filtration, arising from contamination of the

Jan 1, 1962

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,' from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

THE beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than 90 per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as originally proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accumulated since then, showing the utility

Jan 1, 1945

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948