Search Documents

Although the Suggestions to Institute Authors, as revised and amplified over the years to meet changing conditions and experience, have had as their primary objective the guidance of the author who is preparing a paper for record in the TRANSACTIONS, there are in this current version many excellent suggestions for the preparation of any material for publication by the Institute In this connection it should be emphasized that in a sense, and to a degree determined by the editors, the Institute has in its journals "a place for everything," especially a place for the article of practical nature that is of immediate but not necessarily permanent interest Such articles may be referred by the Institute Technical Publications Committee to the editors or submitted directly to them , [Papers (TECHNICAL PUBLICATIONS and TECHNICAL NOTES) authorized for the TRANSACTIONS are, with the discussion, gathered together at the end of the calendar year and with a table of contents and index, bound, according to Branch classification, as volumes of the TRANSACTIONS

Jan 1, 1952

We would like to thank Mr. Mandolesi for his informative paper on rails from strand cast steel. The chemical and structural properties of the strand cast steel were of particular interest to us. We would like to supplement his excellent report with some of Inland's findings from our Caster with submerged nozzles and strands reduced in line from 7" x 7" to 5-5/8" square cross section. Inland has conducted extensive segregation studies on AISI 1049 steel - Fine Grain 0.50% carbon and 0.75% manganese. Based on approximately 80 heats, our normal segregation pattern results in analyses of .49% carbon in the center, and 0.50% carbon at the midway and edge position. The sulfur analysis averages .025% in the center, .027% midway, and .026% at the edge. Note the slight negative segregation between the center and midway position. This steel, being lower carbon and probably cast nearer the liquidus, resulted in less segregation than the 0.80% carbon rail steel.

Jan 1, 1972

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1935 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to members of the Institute that are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Industrial Minerals Division (Nonmetallics); I-Mining Geology; J-Mineral Industry Education Division; K-Mining Administration; I-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of CONTRIBUTIONS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. [ ]

Jan 1, 1936

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts1-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presentation of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about ¼ in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 7, 1958

By L. D. Lash, J. R. Ross

Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per lb which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the US. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold.

Jan 8, 1961

B. S. Crocker (Screened Ore Used for Fine Grinding at Lake Shore Mines, P. 499) was born in Toronto, Ont. and attended Saint Andrews College and University of Toronto. He received a B.A. and M.A. degree. He was graduated with honors and received a fellowship in metallurgy. Mr. Crocker did post-graduate research at University of Toronto from 1933 to 1934. He was employed by Beattie Gold Mines in 1933. He did research in milling at Lake Shore Mines from 1934 to 1936 and from 1936 to 1940 was head of experiment laboratory. At the present time he is mill superintendent with Lake Shore Mines at Kirkland Lake, Ont., Canada. Grinding, cyanidation, flotation and roasting are of special interest to him. He is a member of AIME. Mr. Crocker has presented several papers before C.I.M.M. and also holds membership in this society as well as Professional Engineers of Ontario. Skiing, yacht racing and photography are his favorite hobbies.

Jan 1, 1952

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

By Charles E. Johnston

The haulage system at the International Minerals T & Chemical Corp. (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC's potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad. From three levels, the 800-ft, 850-ft and 900-ft, over 60 million tons have been extracted. Langbeinite (K,SO,. 2MgS0,) is mined on the 850 level and sylvite (KCl) on the 900 level. The 800 level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to more than 10 ft. A room and pillar mining system is used.

Jan 3, 1963

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity air¬borne gamma ray spectrometer with large volume NAI(Tl) crystal detectors. The high-sensitivity spectrometer measures small variations in the concentration of potassium (as Ks°), thorium (as Tl308) and uranium (as Bi.214) along the flight lines in the area surveyed. Hydrothermal dispersion patterns are indicated by anomalous measured values of the concentrations of potassium, thorium, uranium, or their ratios. In two recent Australian survey areas, copper mineralization was located along favorable structures within hydrothermal dispersion patterns delineated by airborne geochemical surveys. In metamorphic terrane where there had been po¬tassium metasomatism, the hydrothermal dispersion patterns were indicated by high potassium/uranium ratios (K40/Bi). In a sedimentary environment that had been intruded by a stock, the path of hydrothermal fluids was indicated by uranium (Bi214), thorium (TV'), and uranium/ thorium (Bi214/Tl208) ratios.

Jan 1, 1972

By H. N. Herrick

THE flow characteristics of drilling muds, as described in this paper, and the method given for solving problems relating to the flow of these muds through pipe and accessory equipment, are based on a conception that drilling muds are plastic solids like paints or greases; not liquids. The data presented in this report have been obtained from studies of California muds, chiefly those used in the Kettleman Hills field, by the Producing Department of the Standard Oil Company of California. Although no claim of scientific exactness is made for the formulas and diagrams, since the data upon which they are based, are not. complete even for California muds, the method has proved to be a convenient means for estimating, closely enough for practical purposes, the pressures required to force muds at various rates through pipe systems in which they are handled. Certain approximations have been made to simplify the procedures so that they can be used easily in the field.

Jan 1, 1932

By A. J. Nicol

Field experience in uranium has shown it is most economical to ram through a drilling program to obtain maximum footage per drill hour. Drift surveys can then determine the course of the holes. Using this method is generally cheaper than paying the additional cost involved in using the drilling technique and equipment necessary to maintain straight holes. Factors Affecting Direction of Bit Travel: In all rotary-drilled holes there is an interplay of forces or conditions affecting the direction of bit travel. Rarely is a straight vertical hole obtained. One of the major factors is weight on a drill string. In looking at a joint of drill stem it is hard to imagine its being quite flexible, but flexing of the steel increases when many joints are made up together, and even a slight weight added to the upper portion causes a buckling or spiraling effect in the hole. The result is that the bit deviates from the vertical.

Jan 1, 1959

By R. V. Ramani, Ish K. Chopra, Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and washability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections, were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected were statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size consist, yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1976

By J. O. Whitely

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By Paul C. Merritt

For more than 100 years, British Columbia has been considered a mountainous mining province, rich with potential but relatively poor in actual production. Times have changed. Today, Japanese interests and money have altered the difficult, if not once impossible, economic conditions and market factors which until recently precluded any great growth of the British Columbia mineral industry. The mining boom now underway in British Columbia has carried the total value of mineral production in the Province to a record height in 1962 as it rang up a 27% increase over that of 1961. Breaking the $200 million barrier for the first time, total value of British Columbia's mineral output reached $229- 276,385. Of this amount, metals accounted for 70%; industrial minerals, 6 %; structural materials, 9 %; and fuels, 15%. The substantial increase is attributed to the record production of copper, iron, asbestos, natural gas and petroleum, in addition to the continuing high production rate and favorable prices of other mineral commodities.

Jan 12, 1963

By J. O. Whiteley

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By Donald Ingvoldstad, Harold E. Lee

At Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse limerock. While oversize material was crushed through Y4-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity.

Oct 1, 1956

By Wilson D. Michell

THE Magma copper vein trends east-west, dips 70° south, and cuts through a 6000-ft thickness of limestones, quartzites, shale, diabase, and schist. The vein is itself a fault with -a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facilitate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, and mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine.

Jan 1, 1947

By J. H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the pH range 8 to 11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction that may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as observed with the Wyoming bentonite. Results indicate the conditions that should be met with respect to pH control to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1985

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960