Search Documents

By R. P. Thomas

Secondary fertilizer minerals are the mineral materials used to supply directly and indirectly the secondary and trace plant food nutrient needs of a fertilizer. Since few soils contain sufficient availability of all plant nutrients for their proper growth, man has prepared mixtures of plant food materials to correct these nutrient deficiencies. These mixtures or fertilizers, when added correctly to a soil, make it possible for abundant and economic crop growth. Many kinds of materials are used as sources of these needed nutrients. They come from natural and synthetic materials and minerals including many beneficiated byproduct compounds. A fertilizer consists largely of carriers of one or more of the three major plant foods, namely nitrogen (N), phosphorus-phosphorus pentoxide (P2O5) and potassium-potash (K2O). Many other nutrients are just as essential for plant growth as the three major plant foods. In fact, the efficient use of fertilizers today depends upon an adequate supply of all these other nutrients. Since these additional materials are usually removed from the soil by plants and supplied in fertilizer in less quantities than the major nutrients, they are called secondary and minor nutrients. In the early days these special nutrients were contained as impurities in the primary nutrient carriers. Today, fertilizers are made primarily from concentrated and synthetic materials which carry very few of these other essential nutrients. Consequently, many secondary and trace nutrient carriers, as salts, byproduct compounds and even minerals have to be added to fertilizers. Secondary Nutrient Carriers The secondary plant foods in fertilizer are next to the major nutrients in abundance. They are calcium, magnesium, sulfur, chlorine, silicon and sodium. Although many of these elements are added to a fertilizer as part of the major nutrient carriers, they are also added in special carriers. The large tonnage of these secondary nutrient carriers used in fertilizers represents only a small percentage of the total production of these materials. A fertilizer producer thinks in terms of materials which supply nutrients instead of minerals. Therefore, these materials will be discussed by elements. CALCIUM Soils need calcium to supply the nutrient needs of plants and maintain the desired physical and biological conditions in the soil. The available calcium is usually 40 to 80 pct of the exchangeable bases. (These bases are ones which can be displaced by other cations and determined quantitatively. They are then expressed as milliequivalents per hundred grams of soil-me.) Direct applications of lime materials such as burnt, ground or hydrated limes are the important sources of calcium for the soil. Most crops, especially legumes, have a high requirement for calcium. The average farmer does not use enough lime to maintain the proper level of available calcium. Hence, it is necessary for many fertilizers to contain soluble calcium materials for efficient use of the major nutrients. The following major nutrient carriers supply some calcium: calcium nitrate, ammonium nitrate mixtures and cyanamid, and many of the phosphates. Both synthetic and natural gypsum are used in fertilizer production. Some crops such as peanuts require a large amount of soluble calcium. Gypsum is the important supplier of this soluble calcium. It is not applied with the fertilizer

Jan 1, 1960

By F. W. Glaser, W. Ivanick

A pressure-sintering method was used to produce binder-free and very dense TiC specimens. Some physical properties of these TIC bodies were determined and found to compare favorably with those of certain cemented Tic grades. It was also observed that the hot transverse rupture strength of TiC bodies remained substantially the same regardless of the amount or type of binder material used. STUDIES of the structure and physical properties of refractory materials have been intensified recently because of the urgent need for nonstrategic materials that retain their strength at high temperatures. Research aimed at determining and improving the physical properties of cemented carbides and borides has been accelerated with a view toward possible use of such materials in connection with turbine blades, rocket nozzles, and other high temperature applications. On the hypothesis that the strength requirements in connection with some of the above applications could be met only by proper choice of cementing agents for such refractory materials, the literature describing the physical properties of borides or carbides was reviewed. However, with a few exceptions,'-" references were found only to compositions containing at least one or more auxiliary binder metals. Cobalt and nickel are among the most frequently employed cementing agents. The melting point of Tic (approximately 3250°C) and therefore the sintering temperature, at which notable densification of a cold pressed Tic powder compact could be expected in the absence of a liquid binder phase, is relatively high. The present study makes use of a high temperature, pressure-sintering procedure, recently described by one of the authors in connection with the sintering of binder-free ZrB,," to produce dense bodies of sintered Tic—free of any cementing agent. During the course of this sintering study, some physical properties of dense Tic bodies produced by this method will be discussed. Materials, Preparation of Samples, Testing Methods The procedure for the forming of Tic powder consisted of mixing graphite and TiH, powders in stoi-chiometric proportions, and heating this mixture in a H, atmosphere and carbon crucible by high frequency, to temperatures ranging between 1900° and 2100°C (3452" and 3812°F). The powdered carbide was then comminuted and screened to the desired particle size. Table I shows the chemical analysis of the two grades that were employed for the production of samples during this work. Bodies of Tic, approximately 2.5xlx0.5 cm were produced in graphite molds that were heated by direct conduction. Sintering was carried out at temperatures for time intervals ranging from approximately 0 to 30 sec under a constant pressure of about 1.3 tons per sq in. An alternate method for the production of samples consisted in cold pressing the individual Tic grades at pressures ranging from 4 to 10 tons per sq in. and sintering in a hydrogen atmosphere in graphite crucibles heated by high frequency induction. Sintering temperatures ranged from 2600° to 2900°C (4715° to 5255°F). Electrical testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp at room temperature. Cross-sectional areas as well as densi-

Jan 1, 1953

By D. H. Gieskieng

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely Werent materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected capacity data. Recording instruments are connected to crushers in such a manner that a continuous record is produced which discloses the inherent maximum capacity of the crusher and shows capacity decreases caused by hangups. The capacity effects of various crushing conditions are made more evident by this arrangement. The recording instruments were first applied to a standard sized 10 by 7 in. Blake-type jaw crusher in the laboratory. Suficient tests were run on this with various combinations of setting, throw, speed, feed sizing, shapes of jaw plates, and other operating features, to establish the individual effect of each on the capacity. The instruments later were applied to much larger crushers in the field, through the excellent cooperation of the managements in the Mesabi Iron Range, and data were obtained which closely corroborated the established trends. The capacity equation resulting from the test work is made up of a series of factors, each representing the contributing effects of setting, speed, width of chamber, nip angle, feed density, type of jaw plates, stroke, and the overall operating technique. Fortunately, most of these factors were revealed to be in direct proportion to the capacity for straight plate chambers. This equation is also applicable to chambers using curved plates, with slight modifications resulting from the capacity limitation of the upper portion of the crushing chamber. The equation has been derived from tests covering a very wide range of feed density and hardness. It has been found valid, providing that the feed material is either nonpacking in character, as is usual, or allowance in designing the crushing chamber shape has been made to accommodate this characteristic. Preliminary investigation has shown that the equation is also applicable to single-toggle jaw crushers. Conditions of this are that the top of the flywheel rotate towards the top of the crusher opening, and that the horizontal motion of the swing jaw relative to the stationary jaw at the discharge opening be considered as the stroke. The relatively large upper chamber jaw motion would probably result in realiza-

Jan 1, 1950

By C. F. Rust

Experimental evidence is presented showing that reproducible formation resistivity factor measurements and resistivity index determinations on reservoir core samples map be made utilizing either the two- or four-electrode methods. Equipment is described which permits the application of either technique to the core specimen without loss of time and with a minimum amount of effort. Since electrical resistivity measurements on reservoir rocks are important not only in electric log interpretations, but also in the study of fundamental rock parameters, it was considered desirable to compare the applicability of both techniques of resistivity measurement. INTRODUCTION The techniques employed in the measurement of electrical resistivity on reservoir rocks, as practiced in the petroleum industry, may be reduced to two fundamental methods: one utilizing two electrodes only, usually referred to as the two-electrode method; the other using two additional electrodes and commonly known as the four-electrode method. In the former, the core sample whose resistivity is to be measured is mounted between two electrodes, usually metal discs, which serve to pass a current of known magnitude through the saniple. The potential drop across the sample, measured between these same two electrodes, and the core dimensions furnish the necessary data to compute he resistivity of the sample. In the four-electrode technique the end plates, again usually ol metal, still serve as current electrodes. Additional probes or electrodes dispersed along the sample are utilized to measure the potential drop. Both methods are used in practice1,2 and it is the purpose of this paper to compare the two techniques as applied to the determination of formation reiistivity factors and the resistivity index exponent n, in Archie's empirical equation I = p/po = Sw 11. To evaluate the two techniques it is desirable to point out the experimental precautions which must be taken to insure reliable results. It is evident from the electrode arrangements of the two- and the four-electrode methods that, for a given sample, the volume of sample included by the four-electrode method is less than the volume included by the two-electrode method. One of the prime difficulties associated with the two-electrode method is the possible occurrence of an abnormally high resistance between the electrodes and the brine-saturated sample, which results in erroneous resistivity values for the core sample itself. Attempts to alleviate this difficulty meet varying degrees of success. Methods used in the past employ such absorbent materials as brine-saturated Kleenex: chamois, or felt. A technique described by Morgan, Wyllie, and Fulton,1 appears to be more satisfactory. Their method consists of spraying or painting the end areas of a core sample with conductive silver paint. This technique reduces contact resistances between the porous medium and the electrodes to a value which is generally negligible as compared to the resistance of the sample itself. In the four-electrode method these requirements are not as stringent since separate probes are used to measure the potential difference acrozs a portion of the sample. In this case, contact resistance occurring at the current electrode; are of no consequence. and those appearing at the potential

Jan 1, 1952

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By F. Habashi

Conclusive evidence is given showing that the dissolution of gold in cyanide solution follows mainly the over-all equation A similar equation can also be written for the dissolution of silver. Theoretical derivation of the velocity equation for this reaction has been obtained, which describes quantitatively the experimental facts. The equation is as follows: where [CN-] and [O2] = the concentrations (in moles/ml) of cyanide and dissolved oxygen, respectively. DcN- and Do2 = the diffusion coefficients of cyanide and dissolved oxygen; 1.83 x 10-5 and 2.76 x 10-5 cm2 sec-1, respectively. A = the surface area of the metal in contact with the aqueous phase, in cm S = the thickness of the boundary layer; varies between 2 and 9 x 10-3 cm, depending on the speed and method of agitation. Rate being expressed in g. equiv. sec-1. INTRODUCTION During recent years a number of papers have been published on the kinetics of dissolution of gold and silver in cyanide solution.1,6 The authors agree that the rate of dissolution is diffusion-controlled, but disagree regarding the mechanism of the reaction. Some authors'-3 support the Bodlander equations: The apparently conflicting results, when critically reviewed, are concordant and lead to the conclusion that the proper equation for the dissolution reaction should be only Eq. 1. This conclusion is based on the following facts: 1) For every 2.2 equivalents of metal dissolved one mole O2 was consumed. 2) For every 1 equivalent of metal dissolved, 2 moles of cyanide were consumed.' 3) Hydrogen peroxide is formed during the dissolution of gold or silver, and for every 2.2 equivalents of metal dissolved, one mole H2O2 was produced.1,2 The fact that Kudryk and Kellogg4 did not detect H2O2 during the dissolution of gold should not throw doubt on the many affirmative reports of other investigators. Lund2 has shown that depending on the crystalline nature of the silver surface, (e.g. method of etching the sample) H2O2 may undergo catalytic decomposition heterogeneously according to: Further Kudryk and Kellogg4 carried out their experiments in the presence of 0.5% KC1 to achieve a greater electrolytic conductivity, and Matsudaira7 has shown that H2O2 is catalytically decomposed (homogeneously) in the presence of C1- ion in alkaline solution. 4) Experiments carried out by Boonstra8 and Lund2 showed that the dissolution of gold and silver respectively in KCN + H2O2 in the absence of oxygen was a slow process. Thus the reaction takes place to a minor extent only. Further kinetic studies showed that: 1) The rate of dissolution depends on the surface area of the metal in contact with the liquid phase, thus indicating that the process of dissolution is a heterogeneous process. 2) The rate of dissolution depends on the speed of stirring,5,6 thus indicating that the process is controlled by a physical phenomenon.

Jan 1, 1967

By Gordon M. Yocom

A pRopeR consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modem methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that he possesses chemical laboratory notebooks

Jan 1, 1941

By B. L. Averbach, Morris Cohen, L. L. Seigle

Free energies, enthalpies, and entropies of mixing of Ni-Au solid solutions containing 5 to 95 atomic pct Ni have been determined by the electromotive force method at 700° to 900°C. The thermodynamic activities exhibit large positive deviations from Raoult's law, and the entropies of mixing are almost twice those of ideal solutions. The enthalpies of mixing are positive (heat is absorbed) and are attributable to the lattice distortional energy resulting from the size difference between the nickel and gold atoms. This factor appears to be responsible for the miscibility gap at lower temperatures. IN the thermodynamic study of metallic solid solutions, most interest has been directed toward systems with negative deviation from Raoult's law, namely, those exhibiting superlattice or compound formation. The results of previous investigations are summarized in recent publications.'-' Relatively little experimental work has been carried out on solid solutions which manifest a positive deviation, possibly because the range of solubility in such cases is usually quite limited. Nevertheless, the relationship of the thermodynamic properties of these solutions to diffusion, nucleation, and precipitation in the solid state are of considerable importance. The binary Ni-Au alloys are particularly suited to an investigation of these relationships. Despite the presence of a miscibility gap at lower temperatures, Fig. 1, indicating a large positive deviation from Raoult's law, complete solid solubility is found above 840°C. Moreover, the difference in the atomic scattering powers of nickel and gold is sufficiently great to permit X-ray diffraction studies of atomic arrangements and pre-precipitation phenomena. Radioisotopes of both nickel and gold are available for diffusion work, and finally, a large difference in nobility between the two elements facilitates measurement of the thermodynamic properties. The present paper describes the experimental determination of the free energies, enthalpies, and entropies of mixing of solid Ni-Au alloys. Table I gives a list of the symbols used in the paper. Experimental Method The stability of nickel chloride relative to gold chloride" indicated that the galvanic cell method could be used for determining the thermodynamic properties of Ni-Au alloys. An electrolytic cell (Fig. 2) was constructed, similar to that of Weibke and Matthes,7 in which the electrodes were solid nickel and Ni-Au alloys, and the electrolyte was a fused mixture of alkali chlorides containing NiCl,. The cell electrodes were made from fine gold granules and carbonyl nickel shot melted together under argon, chill cast, swaged to 1/16 in. diam rod, and annealed for one week at 850°C. Commercial reagent and chemically pure grade salts, purified by dehydration, were used for the electrolyte. The cell, operating in an atmosphere of purified argon, was heated in a resistance-wound cylindrical furnace whose temperature was controlled to within ±0.5ºC. The potential developed between the pure nickel and the alloy electrodes, which is related to the thermodynamic properties of the alloys by standard equations to be presented later, was measured with a potentiometer and a mirror galvanometer sensitive to 10-7 v. Dehydration of the electrolyte was carried out in the assembled cell by evacuating at 100°C for about

Jan 1, 1953

By Gordon M. Yocom

A pRopeR consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modem methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that he possesses chemical laboratory notebooks

Jan 1, 1941

By I. S. Servi, N. W. Marr

TIN markedly increases the softening temperature of pure copper with only a moderate effect on conductivity. Smart and smith' indicated a substantial increase in softening temperature upon addition of different levels of tin up to 0.05 pct in oxygen-free copper. However, after finding no effect of tin in copper containing about 0.025 pct O, they concluded that "the presence of oxygen completely nullifies these changes in properties by precipitation of SnO2.'' Since preliminary tests on Cu-Sn-0 alloys indicated that this conclusion is not valid outside the extremely limited tin range investigated by Smart and Smith, research was primarily directed toward the partition of tin between the copper-base matrix and the oxide phases. Experimental. Material was prepared by sealing an 80 to 100-g charge consisting of oxygen-free copper, tin, and copper oxide into a y-in.-ID quartz capsule which was evacuated and back-filled with tank-grade argon to 3 atm. The sealed vials were heated to 1125ºC, kept at temperature for 30 min, occasionally agitated, and then allowed to air-cool outside the furnace ("as-cast"). The castings were cold-swaged to 0.370 in., annealed 1 hr at 600°C ("as-annealed"), and cold-swaged 16.5 pct ("as-swaged"). Cross sectional wafers were annealed for 1 hr at various temperatures and Rockwell F hardness measured. The "softening temperature" was defined as the interpolated temperature at which the hardness was 50 Rockwell F. Electrical resistance was measured by an ac poten-tiometric method on 0.040-in.-diam wires after a 1 hr anneal at 600°C. Relative accuracy was of the order of 1 pct. Chemical analyses for tin were performed by two methods, identified as "Acid flux" and "HN03 dissolution". The first consisted of fusing the sample with potassium pyrosulfate and leaching the resulting melt with 10 pct sulfuric acid. The spectrophotometric procedure which followed is described in Ref. 2. Oxygen analyses were performed by the vacuum-fusion method with a bath temperature of 1650°C. Tin content of oxides and copper phases was measured with the X-ray microprobe, using a calibration curve based on a series of oxygen-free Cu-Sn alloys. Results. In Fig. 1, the nominal tin composition for alloys containing nominally 400 ppm O was plotted vs the analyzed or the computed tin content—the latter derived from one of the following: 1) "acid flux" chemical analysis; 2) "HN03 dissolution" chemical analysis; 3) X-ray microprobe analysis of the copper matrix; 4) equivalent tin content, based on the measured increase in electrical resistivity (an increase in resistivity of 1.6 microhm-cm is approximately equivalent to 1 wt pct of sn1,3). It is evident from Fig. 1 that the results of the acid flux analysis are consistent with the nominal composition while the HNO3 dissolution method generally yields lower values, consistent with those obtained from electrical resistivity measurements and somewhat higher than those obtained by microprobe analysis. Microprobe and resistivity values are affected only by the tin in solid solution; hence the HN03 method

Jan 1, 1970

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.', ' Other methods employed are the drag and spiral classifiers and the hydroseparator.' These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,' Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6'7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

By John T. Norton, Matthew J. Donachie

Residual lattice strai?zs were produced in 2024 aluminum and ingot iron by uniaxial tensile deformation. These strains were rneasured on the original surface and ulith depth below the surface. The strains conformed approximately to those from a macroscopic stress distribution but they were not truly macroscopic in nature. The exact mechanism which apparently causes the coherently difi9,acting region of each grain to behave as if macroscopically stressed was not determined. MACROSCOPIC stresses in metals produce strains in the lattice which result in X-ray line broadening and line displacements. The latter effect can be utilized in a technique for determining stresses in metals as first shown by Lester and born.' Subsequent advances in technique have enabled the X-ray method of stress measurement to be satisfactorily applied to many problems involving residual stresses of a macroscopic nature, such as those due to welding, grinding, shot-peening, and so forth. In the case of stresses such as those described above, the correlation of X-ray- and mechanically determined data has been generally good. However, plastically extended polycrystalline metals have sometimes been reported2 to show line displacements upon release of the applied tensile load, yet the nature or origin of the residual lattice strains, rls, producing these displacements has never been clear. As will be pointed out, this lack of clarity regarding the macroscopic or microscopic nature and origin of these stresses casts doubt on the validity of results achieved by the commonly accepted techniques of X-ray stress measurement. This anomalous behavior requires clarification to remove the doubts concerning X-ray stress measurement. The present paper is the result of an investigation of the interesting behavior of such plastically extended polycrystalline metal bodies. The studies were originated to carry out the following tasks: 1) Observe whether a residual lattice strain is produced as a result of plastic extension and show whether any residual lattice strains produced can be related to the usual concept of a macrostress. 2) Examine the origin of any residual lattice strains observed. 3) Consider the implications or consequences of the existence of such residual lattice strains on the problem of X-ray stress measurement. THEORY 1) Lattice Strains. The theoretical developments necessary for the treatment of lattice strains and their relation to stresses follow from the classical theory of elasticity and have been adequately covered by arrett. For an isotropic solid under homogeneous deformation, it can be shown that, for uniaxial stresses where Dl is the macrostress acting in the longitudinal direction; E$L is the lattice strain in the plane defined by the surface normal and the longitudinal direction at an angle, , from the surface normal; ET is the similar strain in the transverse plane; E is Young's modulus; and v is Poisson's ratio. Eq. [2] is independent of angle + and Eq. [I] is a linear function of sin2, see Fig. 1, and can be solved analytically for DL if E and u are known and EL is measured. Thus, a uniaxial macrostress will be indicated by a linear E,L vs sinZ plot and a

Jan 1, 1962

By J. W. Matousek, C. S. Samis

me thermodynamic properties of the components in the Cu-Ni-S ternary system have been studied by measuring the H2S/H2 ratios in a gas phase equilibrated with the molten matte at 1200°C. The measured sulficr potentials have been extended by extrapolation and combtned with previously published data to permit the thermodynamic analysis of the ternary system by integration techniques. A simplifying assumption of ideality in the Ni3Sz-CuS pseudobinary has been made. SINCE copper and nickel metals were first extracted from their sulfide ores the interaction between the two metals and sulfur has been of industrial and theoretical interest. The processes developed to extract copper and nickel have been reported periodically in the literature. The theoretical studies on the Cu-Ni-S ternary have been restricted to problems directly associated with production. It is only within recent years that the binary systems related to this ternary have been analyzed thermodynamically and mathematical devices developed to permit a corresponding treatment of the ternary system. In 1910 an investigation of the role of nickel in Cu-Ni-Fe-S mattes was reported,' It was concluded from this work that nickel is not an element replacing iron in mattes, but rather that Cu-Ni alloys behave as a single metal during the matte converting operation. The laws which govern the converting of Cu-Ni alloys were found to be the same laws as those that govern the conventional converting of copper alone. Although considerable information has been reported on the theoretical aspects of copper smelting, little data is available on the smelting of Cu-Ni ores except for phase diagrams and process descriptions. The available information on the Cu-Fe-S ternary and related systems prior to 1953 has been summarized by Ruddle.2 Since Ruddle's publication, Rosenqvist and coworkers have completed phase equilibria investigations of the Fe-S, Co-S, and Ni-S binaries,3 the Fe-S-O ternary,4 and the Cu-Fe-S-O quaternary.4 An extensive investigation of the Cu-Fe-S ternary system at smelting temperatures has been made by Krivsky and Schuhmann.5 At these temperatures, the Cu-Fe-S system is very similar to the Cu-Ni-S ternary with respect to the location of the single-phase and two-phase liquid matte regions. In the former, however, the area of immiscibility is more extensive and the region of liquid matte-liquid metal-solid metal equilibria is much more extensive. Krivsky and Schumann observed that the Cu2S-FeS pseudobinary system is, for practical purposes, an ideal mixture. This investigation has served as a valuable guide in analyzing the Cu-Ni-S ternary. EXPERIMENTAL The experimental procedure employed in this investigation was the conventional technique of equilibration of the sulfide matte with gaseous mixtures of hydrogen and hydrogen sulfide at 1200°C. The thermodynamic properties of sulfur (S2) in the gas phase are determined by means of Eq. [I] and the activity of sulfur in the matte by Eq. [2].

Jan 1, 1963

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By J. B. Newkirk

ABOUT twenty-seven years ago W. bergl discovered that interesting detail could be seen in an X-ray diffraction spot made with a rock-salt crystal if the recording photographic film were held very close to the reflecting crystal. He also showed that much of this detail could be explained in terms of the deformation structure of the specimen. In the same year, 1931, Fox and parr2 reported that X-ray reflections from a quartz crystal were much more intense while the crystal was undergoing piezoelectric oscillation than when it was at rest. This observation was soon confirmed (and explained in terms of X-ray extinction) by Barrett3 in the United States and by Nishikawa et a1.,4 in Japan. During the next few years Barrett refined Berg's method for making X-ray diffraction micrographs and applied it to the study of metallic crystals. He reported this work in the 1945 annual lecture of the AIME.5 Since 1945 relatively little use has been made of the Berg-Barrett (B-B) method for making diffraction micrographs, though considerable interest in investigating subcrystal structures by other methods has developed. Some of these methods depend upon evaporation6 or chemical etching7 and, therefore, suffer from the occasional intrusion of subtle artifacts such as those recently reported by Hooker for leada and Welsh for aluminum.9 Other methods require the introduction of foreign elements which "decorate" the substructure in some way, thereby rendering it detectable by direct" or indirect1'. visual examination. Still others depend upon complex and often highly questionable analyses of X-ray diffraction line profiles. There have also been a number of related X-ray techniques, such as the Lambot,12 Schulz13 and Merlini and Guinier,14 which have proved to be quite useful for specific applications. Some of these methods give a picture of the substructure which is more or less directly related to the shape and the topography of the specimen. The Berg-Barrett method carries this desirable feature to the limit. Closely related to the B-B method are three photographic X-ray techniques recently described by Lang.15 These methods give beautiful pictures of the internal structure of crystals but are limited by the facts that the required apparatus is rather complex, exposure times are long, and the specimen crystals must be thin. An experimental appraisal which I have recently made of the original B-B method has shown that this simple technique is not only inexpensive and convenient, but can give more information than was apparently realized by its inventors. For example, first-order subgrains in iron-silicon crystals were clearly delineated and their relative orientation subject to description. Also defect structures could be seen within the subgrains and in some materials slip bands could be clearly seen with respect to the topography of the rest of the specimen. This much had already been described by Barrett. However, in the present study it was found that the actual sites of individual dislocations which emerge upon the crystal surface could be located. Furthermore, by a simple procedure, the direction (but not sign) of the dislocation Burgers' vector could be defined as well.

Jan 1, 1960

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By Ralph Arnold

Since 1915, when Elk Basin field was brought in, eight oil fields have been developed in Montana and the production has arisen from 50,000 bbl. in 1916 to 8,000,000 bbl. in 1926. The production for 1927 was 5,121,600 bbl. and the total up to the end of 1927 was 27,138,239 barrels. The eight fields, with their year of discovery are: Elk Basin, Carbon County (1915); Devil's Basin, Petroleum County (1919); Cat Creek, Petroleum County (1920); Soap Creek, Big Horn County (1921); Kevin-Sunburst, Toole County (1922); Lake Basin, Stillwater County (1924); Pondera, Pondera and Teton counties (1927); and Bannatyne, Pondera and Teton counties (1927). About 170 wildcat wells have been drilled in the state of which 8 were successful and 162 gas wells or dry. Hence, only one out of 21, or 5 per cent. of the wildcats have been successful. The average depth of the wells has been 1600 ft. and the average cost $32,000 apiece. • Up to Jan. 1, 1927, a total of 1376 wells have been drilled in the producing oil and gas fields of the state, of which 904, or 66 per cent., were successful oil wells; 82, or 6 per cent. were gas; and 390, or 28 per cent, were dry. The percentage of dry wells is excessive as compared to the wells in other states, due to the uncertainties of limestone reservoir rocks. The total production of oil to Jan. 1, 1927, has been 22,016,639 bbl. and of gas 7,265,330,000 cu. ft. The average price at the well for the oil has been $1.47 per bbl. and for gas about 4 c. per 1000 cu. ft. The value at the point of consumption has been about 23 c. per 1000 cu. ft. The total revenue derived from crude oil has been $32,277,119, and from gas 8350,613, or a total income to the producer of $32,727,832. Each well drilled in the state has already (to Jan. 1, 1927) averaged a return of over $21,000. The total number of domestic (Montana) oil and gas companies organized, since the first in 1885, has been 844, of which 702 are still alive and 142 dead. Oil and gas companies registered for operation within the state to Jan. 1, 1927, but with outside charters, are 143, of which 66 are alive and 77 are dead. Outside the few distributing companies, which are included in these figures, the grand total of 997 companies which have

Jan 1, 1928

By V. F. Leferrer

A new process for the treatment of silver crusts from desilverization of lead has been developed by Societe de Penarroya. The zinc contained in the crusts is recuperated by vacuum distillation at low temperature. The use of special retort crucibles is avoided. AT Noyelles-Godault the Parkes process (zinc addition to a silver-bearing lead melt) is used to desilverize lead bullion from the blast furnace. The crust which rises to the surface of the bath is removed and pressed by a well-known process in a press of the Howard type. The pressed crust, called zinc crust or silver crust, contains 10 pct Ag, 30 pct Zn, and 60 pct Pb. It is melted under a salt bed in a small, narrow, and deep kettle heated only in its upper part. A liquid concentrated alloy is obtained which is called T.A.C. in France (triple alliage concentr6) analyzing approximately 25 pct Ag, 65 pct Zn, 8 to 10 pct Pb, and 1 to 1.5 pct Cu. This T.A.C. is a real metallic alloy, completely deoxidized, and can be stored indefinitely. The process used at Noyelles-Godault consists in distilling this alloy in a tight furnace, under low vacuum and at low temperature, so that only the zinc distills and is condensed into liquid form. The residual silver-bearing lead is almost entirely free from zinc and oxidized dross. The vacuum dezincing equipment, see Figs. 1 and 2, consists of: 1) A furnace, constituted of a casing of steel plate lined with refractory bricks, heated internally by means of graphite resistors. The temperature of the furnace is measured by a thermocouple device and controlled by an automatic temperature regulator which acts upon the flow of the current passing through the resistors. Two doors, numbered 1 and 2 in Fig. 2, are provided for, one for charging the T.A.C., the other for tapping the high silver-bearing lead. 2) A condenser, and an ordinary room lined with good heat conductor refractory material. This condenser is provided with a graphite resistor which serves to bring to temperature when starting the furnace. A thermocouple records the temperature of the zinc melt and controls the temperature in the furnace, that is, the flow of current through the resistors, by means of the above mentioned regulator, so that the distillation rate in the furnace does not exceed that of the condensation. The condenser is connected to the vacuum pump by a filter. The whole equipment should, of course, be fluid-tight. The operation is carried out under a vacuum of about 10 mm Hg.

Jan 1, 1958