Search Documents

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By Heihachi Kamura

The reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe2O3 + 3CO = 2Fe 4- 3CO2 2Fe2O3 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of earbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing equation, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also on the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium. Chemical Equilibrium of Iron, Oxygen, and Carbon Investigations concerning the equilibrium between iron, oxygen, and carbon have been carried out by E. Baur and A. Glaessner,1 who deter-

Jan 1, 1925

By William Fink

THE investigation of the phase relations of high-purity aluminum-base alloys is a part of the fundamental research program of the laboratories of the Aluminum Company of America. The results of a number of binary and ternary systems have previously been published in the transactions of this society. The aluminum end of the binary aluminum-titanium system has been studied. This system has received relatively little attention. To the authors' knowledge, there are two previous papers on this subject. E. van Erckelens1 determined the constitutional diagram reproduced in Fig. 1. .According, to this diagram, the liquids represents the separation of TiAl4 (Ti = 30.7 per cent.). He concluded that this is the composition of the compound, because in his work the eutectic horizontal terminated at 30.7 per cent. titanium and the metallographic examination of a sample of this composition revealed only one phase. According to the constitutional diagram developed by W. Manchot and A. Leber,2 reproduced in Fig. 2 from data given in their article, the liquidus represents the separation of the compound TiAl3 (Ti = 37.2 per cent. ). The composition of the compound was derived in a manner similar to that utilized by van Erckelens. Moreover, Manchot and Leber confirmed the composition of the compound by analysis of the constituent left as a residue after dissolving the alloys in weak sodium hydroxide solution. Although these are the only publications describing the constitution of the system, other investigators have studied the composition of the titanium compound. L. Wöhler3 says that there is a compound TiAl3 which was later confirmed by W. Manchot and P. Richter4 and by

Jan 1, 1931

By F. R. Hensel

THE absorption of oxygen by molten metals is a quick and convincing method to determine the metallurgical characteristics of various types of furnaces.1 The investigation was restricted to the use of coreless induction furnaces. A major variable in induction furnace practice is the frequency and its influence was studied by comparing melts made in a 5000-cycle and a 60-cycle induction furnace respectively.2 The authors are not aware that such a comparative study has been made before and therefore present this paper in the belief that the results will be of general interest. ANALYTICAL METHODS FOR DETERMINATION OF OXYGEN IN NICKEL An analytical procedure for determining NiO by a quick and simple, laboratory method has been worked out in collaboration with Dr. Herty, of the Pittsburgh Station of the Bureau of Mines. It was found that Dr. Herty's aluminum method as used for the. determination of FeO in iron and steel was very suitable for use with nickel if instead of hydrochloric acid a 10 per cent solution of nitric acid is used for bringing the metal into solution. Essentially this method involves deoxidizing the nickel-oxygen alloy with aluminum (2Al + 3NiO = Al203 + 3Ni) and determining the resulting Al203 by a residue analysis. The original oxygen content can then be calculated from the amount of Al-20,. The method as suggested by Dr. Herty3 is referred to in the present paper as method B. A slight modification of method Bled to the application of method A, a description of which is given below according to F. W. Beiter?:3

Jan 1, 1932

By Keijiro Nishio

At a time of great antiquity when our Yomato tribe had not yet found its way throughout the country, there lived in Japan barbarous tribes of the stone age, whose dwellings were vertical caves covered with roof's of twigs and weeds. In a cave lately discovered at the village of Morita, 10 miles west from the port of Aomori, there were found pieces of micaceous iron-ore and psilomelane, with oval holes pierced from both sides. Apparently these objects were regarded as ornaments or curios, without being applied to any practical use. Among the traditions given in the Nihonshoki, an ancient history of Japan, there is one relating to the mining industry. According to this tradition, in the mythological age Izanami-no-Mikoto gave birth to Kanayamahiko-no-Mikoto, god of mines, and Amaterasu-Okami (the sun-goddess) was armed with swords. It came to pass at one time that she concealed herself in Ama-no-Iwato ("Heavenly Cave"), and several gods made contrivances to entice her out. Among them, Ishikori-dome, a smith, made a mirror with copper obtained from the Ama-no-Kagoyama, by means of a pair of bellows known as the Ama-no-habuki, which was made of a deer-skin. It is recorded also that Susanb-no-Mikoto, her younger brother, observed the abundance of gold and silver in Korea, where his descendants were to reign, and urged them to provide themselves with boats to convey them across the Sea of Japan. In the course of time he accomplished his object, proceeding to Korea with his son, Isotakeru-no-Mikoto. These accounts

Jan 1, 1913

By Francis Lucas

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or-under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black, oxide that cannot be absorbed by the metal.

Jan 1, 1927

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration 'are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which lie had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1878

By Claude H. P. Lupis, John F. Elliott

IN the recent past, extensive use has been made of the interaction coefficient in treating the thermody-namic behavior of components in solutions at dilute concentrations. The development of this concept by wagner1 and chipman2,3 is sufficiently well-known so that its elucidation here is not necessary. The present discussion is focused on the relationship between E and e. The usual forms of the coefficients are:

Jan 1, 1965

By A. W. Ashbrook

From both economic and environmental aspects, the loss of organic materials from a solvent extraction process is of major concern. A decade ago perhaps the only consideration given to solvent loss was economic in nature. Today, the environmental -.and hygiene - impacts have to be seriously considered. In this section we shall deal essentially with the processing and economic aspects of solvent loss; the environmental aspects are discussed in a later section.

Jan 1, 1978

By P. Barnes

(Read at the Amenia Meeting, October, 1877.) THE subdivisions of this account are numbered 27, 28, 29, 30, 31, 32, and 33, in the general series of construction accounts, and give the details of cost of the various items of the work, as noted below: Accounts 32 and 33 -relate to hand-tools and to heaters, and, being quite small in total amount, are omitted in this statement.

Jan 1, 1878

By D. Brabec

Previous studies have demonstrated the possibility of using aqua regia-extractable copper and zinc in plutonic rocks in exploration geochemistry. The present investigation compares this method of extraction with hydrofluoric-perchloric acid attack and bisulfate fusion in terms of precision and discrimination between high and low concentrations. Statistical treatment of data shows that the overall performance of the aqua regia method compares very favorably with other methods of attack.

Jan 1, 1972

By Desmond Y. M. Lee

Computerized preventive maintenance has been a long sought goal in many industries. People have firmly believed that proper implementation of such a system can result in tremendous saving of money. However, the preventive part has always been left out without realizing it due to the inflexibility of coping with environmental changes. With this in mind, the Iron Ore Company of Canada has developed a computerized system which schedules maintenance jobs preventively.

Jan 1, 1977

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

JAMES.E. HOWARD, ? Washington, D. C. (written. discussion ?).-It is a pleasure to participate in the discussion of a paper on the endurance of steel to repeated alternate stresses. For many purposes the prime and only function of the metal is to resist strains and stresses: stresses of long duration in one direction only; stresses that alternate between a maximum and a. minimum in' one direction; and stresses of different de-

Jan 4, 1919