Search Documents

By J. C. Irvine

Meramec Mining Co., a joint venture of Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property is located near Sullivan, Miss., about 113 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the ore body was mineable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production began in April 1964. The ore body is overlain by about 400 m (1300 ft) of flat-bedded sediments. It is tabular, about 800 m (2600 ft) long and up to 180 m (1600 ft) thick. It dips about 80° and is of unknown depth. The ore is mainly high-grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry.

Jan 9, 1976

U.S. Steel Uncovers Massive Iron Ore Deposits in Nevada United States Steel Corporation has confirmed that mineral investigation in Lyon County, Nevada. has been under way since 1960. Confirmation followed press reports of a statement attributed to a Nevada State inspector of mines to the effect that the Corporation has found a major iron ore deposit that may also contain copper ill West Central Nevada. Drillings over the years in a number of locations have indicated extensive iron ore bodie containing a possible quarter of a billion tons of ore of a basically magnetite composition. analyzing less than 40% iron, which would require beneficiation for commercial use. Some of these deposits are deep- lying while others would permit open pit mining. These bodies contain copper in quantities of approxiimately 0.3%. More recent drilling in another area has disclosed evidence of additional deeply-lying deposits of a lower fe content but with more promising indications of copper. A realistic estimate of fe and cu ore reserves cannot be made until more drilling is completed.

Jan 1, 1970

By Lyall Zickrick

EXPERIMENTS of previous investigations have indicated that calcium-copper alloy, when used as a deoxidizer for molten copper, results in a sound copper casting of good physical and electrical properties. Bradenberg and Wiens1 have obtained successful results in casting sound copper using calcium for deoxidizing. Masing2 has obtained deoxidized copper of high density and high conductivity by use of calcium. Pratt,3 in 1907, patented the use of calcium for the deoxidation and degasification of, copper. Schumacher, Ellis and Eckel 4 in 1929, conducted a series of experiments on deoxidizing copper with calcium. They concluded that so long as there is only a small percentage of residual calcium the mechanical and electrical properties of the copper deoxidized are not impaired; and the deoxidation is thorough. For this investigation, a, copper-calcium alloy high in calcium and 10 variously deoxidized copper ingots were prepared. The investigation concerns itself with the casting properties and structure of these variously deoxidized ingots, their working and annealing characteristics, and the resulting physical and electrical properties of the worked materials.

Jan 1, 1932

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

SINCE the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error.

Jan 1, 1942

By Henry Logan

THE purpose of mine-hoist safety con-trollers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper accel-eration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoist-ing drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of me-chanical hoist controllers, the basic ele-ments of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical con-nections would cut off the power and set the brakes.

Jan 1, 1940

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but cannot be obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Co. in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1973

By Charles E. Johnston

By substituting photoelectric automatic car loading for mechanically induced hydraulic automatic loading and by protecting the process against operational failures, the engineering staff at International Minerals & Chemical Corp.'s Carlsbad potash mine has developed a reliable loading process that operates without an attendant. The photoelectric control, developed primarily because of frequent failures in the hydraulic control system, has not changed the basic loading operation and physical layout. Mine-run ore ranging in size from minus 200 mesh to 30-in. lumps is dumped onto a conveyor belt which discharges into a so-called "flop gate chute" which in turn, feeds the ore into six-ton capacity mine cars. Each car is filled progressively by moving the entire trip forward. When a car is filled 12 in. above its rim, the direction of flow into the car is reversed 180º and filling of the next car back is begun while the entire trip is moved forward again. Once the next car is properly spotted under the front chute, the flow is again directed to the forward position.

Jan 9, 1962

By John J. Howard

WE are approaching the depletion of our principal source of iron ore-the Great Lakes deposits, which have provided 85% of the nation's requirements for the past fifty years. This situation presents a threat to our standard of living and our position as a world power. Fortunately, in the Great Lakes region there are still tremendous quantities of potential iron ore in the form of the low iron, high silica rock called taconite. The economical extraction of iron from taconite will insure our future steel supply if no new deposits available to the United States even in time of war are discovered. In the new process presented here, the iron is reduced directly by a simple method and then separated from the silica. The product is "feed," not to the blast furnace, but to the steel plant. This process requires very much less plant, less physical and chemical treatment, and less fuel and auxiliary materials than the conventional ore concentration-blast furnace method. In my opinion, this new, fundamentally different approach offers a better hope for the solution of the iron ore problem.

Jan 5, 1950

By H. L. Ames, P. H. Jennings, R. W. Stanley

A process has been developed for leaching copper, lead and calcium from molybdenite concentrate. The leachant is a solution containing an oxidizing chloride (e. g., CuC12, FeC13) and an alkaline earth metal chloride (e. g., CaC12). Cupric chloride and ferric chloride, in the presence of 20-30% calcium chloride, are effective oxidants for chalcopyrite and galena. Calcium chloride, in addition to promoting the rate of leaching, serves to lower the solution pH and raise the boiling point. Leaching for two hours at 110'~ with a 1 % CuC12-10% FeC13- 30% CaC12 solution results in the extraction of up to 98% of the copper in molybdenite, 98% of the lead, and 79% of the calcium. Less than 0. 5% of the molybdenum is dissolved. The leach solution can be rapidly and effectively regenerated with gaseous chlorine and recycled. Build-up of copper and lead in the leach solution is controlled by discarding about 30% of the leach solution each cycle.

Jan 1, 1973

By Mark S. Childs

FRIEDENSVILLE orebody in Lehigh County, Pennsylvania, lies in the south central part of the USGS Allentown Quadrangle. Physiographically the area is located in a small reentrant-known as Saucon Valley-of the Great Valley Province into the Reading Prong of the New England uplift. Saucon Valley itself is an oval-shaped lowland eight miles long and four miles wide, surrounded by ridges except where connected with the Great Valley through a breach in the rim known as Saucon Gap. These ridges, composed of Pre-Cambrian metamorphic rocks and Cambrian quartzites, rise some 500 ft above the valley floor. They are continuous with the New Jersey Highlands. The valley lowland is immediately underlain by lower Paleozoic dolomites and limestones. This area is one of low relief having a swing of approximately 100 ft, with an average elevation of 375 ft above sea level. The entire valley, which has a water shed of about 58 sq miles, is drained by Saucon Creek. This unit flows in a northeasterly direction to the Saucon Gap, where it discharges into the Lehigh River.

Jan 1, 1957

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By W. P. Blake

The mining district and the town of Tombstone are situated in Cochise County, Arizona Territory, at the northwest end of the Mule Pass range of mountains, in longitude 110°, and latitude about 31 40' N,, upon the right bank of the San Pedro River, from which the town is distant 9 miles east.. It is also 24 miles south of Benson station on the Southern Pacific Railroad of Arizona, and about 40 miles north of the Mexican line. Its altitude above the sen is 4600 feet. The Dragoon Mountains rise across a valley to the northeast, and the Huachuca Range similarly upon the southwest. The country is open, without timber, and the surface, where the mines are opened, is in general gently rolling, and accessible to wagons by. natural roads. The first locations were made in the pear 1878 by the Scheffelin brothers and Richard Gird, the latter being well known among the pioneers of Arizona as a surveyor and miner, who contributed largely to our knowledge of the geography of the Territory in early days,

Jan 1, 1882

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

By James Elton

THIS paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting- & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in. expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a by-product in the smelting of other metals. It is seen on the market in various forms, the most common being arsenic trioxide, the ? white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports.

Jan 8, 1913

By J. M. Johns

INTRODUCTION The Climax Mine is located on the continen¬tal divide, on Fremont Pass, about 145 Km south west of Denver, Colorado. Molybdenum, along with the by products, tungsten, tin, and pyrite are produced from both the open pit and under¬ground operations. The underground operation utilizes a panel caving mining system, and produces in excess of 27,000 mt per day. In the mid 1930's, the Climax mine began changing from a grizzly level layout to the slusher drift system which is still in use to¬ day. Over the years, the slusher drift layout has been refined to correct, improve, and sim¬plify minor operational problems. In common with most older hardrock mines, the development equipment used at Climax was the standard rail mounted, pneumatic mining machinery. This type of equipment remained in use, at least to some degree, until about four years ago. For production, 112 Kw electric slushers were used, while mine traffic was rail with trolley locomotives. Beginning about ten years ago, Climax began

Jan 1, 1981

By Vincent Carlsson

A comprehensive investigation has been undertaken to clarify how pellets are affected by alkali circulating in the blast furnace. The investigation has been performed with acid and basic pellets in a special furnace. Experiments were carried out to ascertain the influence of potassium on swelling and reducibility when added at different stages of reduction. After that, the significance of the quantity of potassium added in the hematite stage was studied. A parallel experiment with sodium as the alkali component was also con- ducted. Besides these vaporization experiments the effect of alkali on softening and reduction characteristics at high temperatures was investigated. The results showed that alkali always increases swelling, especially when added in the hematite stage. The addition of alkali increases reducibility of acid pellets during reduction from wustite to 70 % reduction. The softening temperature is significantly lowered by the addition of alkali and is, in any case, lower for acid pellets than for basic pellets. The microscopic studies showed that alkali ferrites can be formed irrespective of the influence of alkali on the slag phase.

Jan 1, 1977

By W. H. Emerson

In the summer of 1894, a specimen of corundum from Acworth, Ga., which mas reputed to be of markedly inferior quality for the manufacture of corundum-wheels, was received by the Geological Survey of Georgia, with the request that it be analyzed, in order to ascertain whether this inferiority was associated with any peculiarity of composition. In its appearance there was nothing uncommon, though it seemed to be rather easily scratched with a knife, while, at the same time, it scratched agate easily. An analysis gave the following results: Alumina, 94.58; silica, 1.77; magnetic oxide of iron, 0.69; calcium oxide, 0.44; and water, 2.51 per cent. There is nothing unusual in this composition, except the amount of water, which is usually, in southern corundum at least, from 0.3 to about 1 per cent. Concerning this corundum, the Mineral Resources of the United States, 1893, pp. 676 and 677, Bays: "It is supposed that this variety of corundum contains a little water, as it is

Jan 1, 1900

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1946

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By L. Messulam, A. S. Appleton

Iwo major studies of the Fe-Cr-C system are available in the literature. The earlier one of Kinzel and crafts' forms the basis for the data most commonly quoted in works of reference (e.g., Metnls HandDook) though the later work of Bungardt el a1.' is more extensive and amenable to analysis in terms of isothermal sections and so forth. However it is evident from examination of either of these studies that the delination of phase boundaries on the basis of the data obtained can only be very approximate. Indeed in several instances the data are so inconclusive that this delineation is a matter of opinion. This note is to report an analysis of experimentally determined carbon activity data in this system, which, originally intended as a means of checking the self-consistency of the data for a number of alloys, enables some conclusions to be drawn concerning the 10503C isothermal section of the iron-rich corner of the system as deducible from the data of Bungardt

Jan 1, 1967