Search Documents

By R. E. Jenkins

The Bell Canyon member of the Delaware Mountain group has yielded quite a large number of fields in which completion and production problems have been numerous and complex. Reserves are difficult to estimate due to the problem of evaluating the formation water saturation, and the feasibility of water flooding is questionable. Extensive laboratory investigations were undertaken to determine if normally measured rock and contained fluids properties could account for many of the peculiar characteristics of the formation. A statistical study or routine core-analysis data was made. Capillary-pressure data were obtained by several techniques. Fresh-water and brine permeabilities were measured and relative permeabilities of oil, water and gas were determined. Some qualitative wetta-bility tests were performed, and the petrography of a few thin sections was studied. The results of this work are presented, with typical or average data shown for each test. The permeability -to- water characteristic of the Delaware was found to be abnormally poor. Correlations of laboratory and field performance data indicate high water saturations in much of the formation. Pore geometry is highly uniform. INTRODUCTION The Delaware formation has undergone extensive exploration and development in the past few years. This has resulted in the discovery of quite a number of fields—producing oil for the most part. A large percentage of the productive wells have produced water along with the oil. Often there is no apparent pattern for the percentage of water cut experienced. In several instances vertical displacments of over 200 ft have been established between communicating wells in which the formation appears to be about the same, yet the structurally high wells yield a much higher water cut than the lower wells. Drill-stem tests have contributed little to well completion because they nearly always show small amounts of water (usually mud filtrate), regardless of what is produced later in the life of the well. Other formation evaluation methods have had no more than limited success in indicating ultimate productivity. Consequently, predicting the type of fluid productivity of Delaware wells has been very difficult. Hydraulic fracture treatments are almost universal, and unstimulated Delaware wells have not exhibited the productivity that normally would be expected of wells with the specific permeabilities encountered. Some operators have indicated that their Delaware wells need frequent re-stimulation. The uncertainty of reservoir water saturations reported for the Delaware has made difficult the task of evaluating oil in place in the reservoirs and estimating primary recovery. The unreliability of this data also will cause feasibility studies for water flooding or other secondary-recovery methods to be problematical. Several opinions have been voiced to explain why the Delaware performs as it does. Chronically poor well completions, dynamic water and tilted water tables, capillary inequi-libria, peculiar relative permeability characteristics and oil-wetness are among the suggested reasons. The dual purpose of this paper is (1) to describe the principal rock characteristics, and (2) to present an evaluation of those characteristics so that approaches can be made to explain the irrational behavior of wells completed in the Delaware. STUDY OF ROUTINE CORE-ANALYSIS DATA A statistical study of routine core-analysis data has been made to relate fundamental rock properties and characteristics of the formation to well productivity. For the most part, well production data were obtained from operators and augmented by production data from commercial information services. Only data which were available in detail and which were considered to be accurate were used. The core data used were obtained on samples from the perforated or open interval only and, thus, may not always represent the total productive interval in a well. All the core-analysis data included in this study are from the Bell Canyon member of the Delaware and were obtained by "plug-type" techniques, as opposed to whole-core or full-diameter techniques. Porosity values were obtained by the summation-of-fluids technique, permeability values are air permeabilities corrected for slippage to an equivalent liquid permeability, and the oil and water contents were determined by means of a high-temperature downdraft retort. All the procedures used are discussed at length in Ref. I. The core-analysis data were sorted

By L. Larson

SMELTERMEN in the copper industry know that punching the tuyeres of a copper converter is a difficult, disagreeable, and at times a hazardous job. Knowing this, many men in the industry have given serious consideration to punching by mechanical means. As evidence of such consideration, a great many patents have been issued covering various mechanical devices or machines for doing this task. In 1942, as war-created manpower shortages became more acute, it became increasingly difficult to get men to punch tuyeres. Faced with this situation at the McGill smelter, it was decided that an all-out effort should be made to develop some sort of a mechanical punching device. The various patents were studied over thoroughly but none of the devices seemed suitable, all were discarded and it was decided to develop one, using the ideas of the personnel at McGill. Initial test work indicated that a separate punching device should be attached to each tuyere. This meant that an adapter would have to be developed which would accommodate such a device; the adapter to be so constructed that it could be substituted for the regular Dyblie valve head, and be punched either by mechanical means or by hand. Also a method for quickly attaching or detaching the punching unit would have to be devised. If the punching unit was attached to the adapter, then the punch rod and tip would have to remain inside of and reciprocate within the tuyere pipe. This last requirement meant that the punching device, the adapter, the piston rod, and punch rod must be in perfect alignment. The whole arrangement thus would become an integral part of the converter and would rotate along with the tuyere line to all the positions required for converter operation. If the puncher was to rotate with the converter, there was also a problem of limited clearance. The construction of a device to meet all of these conditions imposed many problems. In the latter part of 1942, two pieces of equipment were constructed and tried out under test-stand conditions. Both of these devices were very crude, but test-stand operation indicated that progress was being made. Neither of the units was considered good enough to be attached to and tried out on a tuyere of an operating converter. In May 1943, work was started on another device and in August of that year it was attached to and actually punched a single tuyere of a converter on an experimental basis (fig. 1). This unit was essentially a cylinder 3 in. in diam and about 15 in. long inside. Valve ports were so located as to provide a 1-in. cushion on each end of the stroke. The cylinder ports were piped to a 3/4-in. four-way disk valve. High pressure air (90 psi) was delivered to the valve by means of a long hose, thus making it possible to supply air to the device at all operating positions of the converter. The forward and return punching strokes were accomplished by shifting the valve handle as required. With the 3/4-in. valve, stroke velocities from 15 to 18 fps were achieved. Punching with this experimental arrangement was carried on for some time, but many difficulties were encountered. The punch rod tips often stuck in the tuyere accretion, indicating that more energy of some sort was necessary to avoid sticking the punch rod. To overcome sticking, experiments continued with a speeded up unit and although progress was made, troubles of various kinds continued to appear. On this unit, piston cup seals passed the valve ports which proved to be of very poor construction. Also the piston, driven forward at approximately 28 fps, would often bottom metal to metal in the forward end of the cylinder causing both mechanical and operational trouble. Sometimes the punch rod and at other times the piston rod would break loose and be shot through the tuyere pipe into the converter. Bottoming and poor timing of valve reversal caused a bounce and a hesitation at the end of the forward stroke, with the result that the punch rod

Jan 1, 1951

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.'j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

By D. G. Westlake

Alloys of poly crystalline Nb-H have been tensile tested at 77" and 120°K after slow-cooling and after quenching from room temperature. A rationale has been developed to explain the effect of cooling rate on ductility in terms of microstructure. The inferior ductility of the slow-cooled alloys in this temperature range can be attributed to the precipitation of coarse hydride particles that fracture in the early stages of plastic deformation. Quenching Produced much smaller hydride particles and a decreased tendency for initia-tion and popagation of cracks. Prismatic dislocation loops, punched into the matrix of quenched alloys, eliminate the yield point and may Play some role in the low temperature ductility of the quenched alloys. The difference in ductility between quenched and slow-cooled V-H alloys was even greater than that observed in the N b-H alloys. It is well known that the ductility of Nb-H and V-H alloys decreases with increasing hydrogen concentra-tion and with decreasing temperature.1-l1 The follow-ing are some of the numerous mechanisms that have been adopted in attempts to explain these observations: 1) hydrogen-dislocation interarction,4'6 2) lowering of the crack surface energy by adsorbed hydrogen,9'10 3) localized lowering of the niobium bond strength,9 and 4) exertion of pressure inside voids by molecular hydrogen.6 A recent study1' indicates that, in some way, the embrittlement is related to the precipitation of a hydrogen-rich phase, because embrittlement and hydrogen solubility have the same temperature dependence. Most of the investigators observed that at very low temperatures there was a return of the ductility. Thus, hydrogenated niobium and vanadium may be said to exhibit a low temperature ductility minimum."1'8'9 It has been reasoned by most observers that diffusion is required for the embrittlement mechanism to be operative, and that as hydrogen becomes immobile at very low temperatures, the ductility increases. This investigation of the mechanical behavior of Nb-H al-loys under various conditions is an attempt to gain a better understanding of the low temperature ductility minimum. EXPERIMENTAL Tensile specimens, with gage length dimensions 20 by 3 mm, were machined from sheet stock" and both faces were ground on wet 600 grit Sic paper to obtain a final thickness of 0.5 mm. Annealing as described earlier12 resulted in average grain diameters of 0.3 mm. The recrystallized niobium tensile specimens were electropolished in 90 parts H2S04, 10 parts HF (48.9 pct) by volume, at 287°K and 30 v. Hydrogen, which may have been present in the starting material and/or added during specimen preparation, was removed by annealing at 1073°K in a dynamic vacuum of 2 X 10-6 torr. Hydrogenated specimens (1.15 at. pct H) were prepared by reaction with a known quantity of pure hydrogen (obtained by thermal decomposition of UH3) at 1073oK, followed by cooling at the rate of 100" per hr. These were vacuum encapsulated, homogenized at 573°K for 3 to 5 hr, and furnace-cooled. Tensile tests were conducted on an Instron machine at a strain rate of 4 x l0-5 per sec. The gripping device was such that the specimen was positioned below the crosshead. Thus, subambient test temperatures could be obtained by immersion of the device in a cooling bath of either liquid nitrogen or Freon-12. The temperature of the Freon-12 was controlled within ± 0.1°K of the desired temperature by automatically monitoring the flow of liquid nitrogen through a copper coil in the bath. Slow-cooling to 77°K was accomplished as follows. The testing device was surrounded by a rubber jacket, open at the top and with small holes in the bottom. Liquid nitrogen, brought up to the bottom of the jacket, entered the holes and vaporized quickly. The temperature was monitored at the specimen with a copper-constantan thermocouple, and a constant cooling rate of 2 deg per min was easily achieved by controlling the level of the liquid nitrogen outside the jacket. RESULTS AND DISCUSSION Low Temperature Ductility Minimum. Resistometric studies of both Nb-H12 and V-H13 indicated that at tem-peratures less than 150°K, virtually all of the hydrogen

Jan 1, 1970

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By J. J. Gilman

Examination showed that characteristic cleavage step patterns are observed on the cleavage surfaces of undeformed, slipped, bent, twinned, compressed, and indented zinc crystals; and the effect of temperature is discussed. Dimples were seen to produce cleavage steps in a treelike pattern in otherwise undeformed crystals. The steps seem to originate when cracks intersect screw dislocations. IT has been known for a long time that the path of fracture in polycrystals may be discontinuous (see Jaffe, Reed, and Mannl for review). Recently, Kies, Sullivan, and Irwin2 have proposed, and given evidence, that crack propagation is discontinuous within individual crystals as well. Other evidence has been given by Low.' When discontinuous cracks within a crystal join together to make a macrocrack, the lamellae between each set of two cracks are torn somewhere, forming small cliffs. These cliffs appear as lines when the cleavage surface is observed microscopically.4,5 The lines have been called vein, tree, and riverlike markings by various authors, and they have sometimes been mistaken for fissures. The descriptive term cleavage steps is used in this paper. Cleavage steps vary in height over a wide range of values, from molecular dimensionsG to lor. and larger. Kies, Sullivan, and Irwin,2 as well as George,' have shown that the gross cleavage step patterns for plastics, polycrystalline metals, and for mono-crystals are sometimes similar. Thus, they depend mostly on the mechanical variables that prevail during cleavage and are relatively insensitive to the structure of the material. For example, parabolic markings2,7,8 sometimes result when cracks open up ahead of, and not coplanar with, the main crack front. If the advance crack has the same velocity as the main crack, their intersection line is a parabola, otherwise it is a hyperbola or an ellipse. The patterns are strongly affected by differences in crack velocities. This results in chevron patterns which point to the place of origin of the main crack. It is the purpose of this paper to demonstrate the existence of a mechanism of cleavage step formation which is a continuous rather than a discontinuous process. Also, certain characteristic step patterns are described, and the strong effect of temperature is shown. The specimens were zinc monocrystals (grown from 99.999+ pct pure metal). These were cleaved at room temperature and at — 196°C. Results and Discussion Cleavage step patterns are highly variable from point to point on a given specimen, as well as from one specimen to another. Although the patterns shown in the photographs are typical, they have been selected for graphic illustration. Figs. la and lb compare undeformed crystals that were cleaved at —196 °C and room temperature, respectively. Cleavage at room temperature (Fig. lb) resulted in a higher density of high steps (dark black lines) and enhanced the visibility of the fine background markings. Deformation by simple slip caused no marked change in the step patterns until the glide strain reached about 1.0. But, as Fig. lc shows, the density of high cleavage steps was greatly increased by large glide strains. Corrugations lying perpendicular to the slip direction may also be seen in Fig. lc. These are caused by deformation bands. The cleavage resistance of the crystal of Fig. lc was very high compared to undeformed crystals (estimated by the force on a needle required for cleavage). Striking and varied cleavage step patterns were observed on bent crystals. Two characteristic patterns that were observed on crystals bent at 25°C, and cleaved by reverse bending at —196°C, are shown in Figs. 2a and 2b. The first, Fig. 2a, consists of V-shaped lines similar to the parabolas of other materials2,7 Fig. 2b shows a pattern that is the equivalent of Fig. la, consisting of faint background lines with a few higher step markings. Cleavage of bent crystals at room temperature resulted in Figs. 2c and 2d. Now, the cleavage step lines show a strong tendency to follow one of two perpendicular paths. In Fig. 2c (bent once), many of the cleavage step components that lie parallel to the bend axis are assembled into irregular lines. In Fig. 2d (bent twice), the cleavage steps again tend to consist of two perpendicular components, but neither of the components is assembled into lines. Also, the step density is higher.

Jan 1, 1956

By F. W. Archibald

The American Smelting and Refining Co. has standardized its copper converting practice to attain a maximum unit blister production with a minimum of refractory consumption by careful location of the tuyeres and by applying magnetite coatings on the hard-burned magnesite brick linings. THE American Smelting and Refining Co. operates four primary copper smelters in the United States with a total of 17 Peirce-Smith type converters; 15 of them are 13 ft in diameter by 30 ft long, and two are smaller. Some details of operations vary with locale; however, fundamentals of design, operation, and maintenance are common to all plants. All converter shells are l-in. thick except for one new converter with riding rings on the ends which has a shell thickness of 1 1/2 in. More tuyeres can be installed with rings on the ends and hence more air can be used. Welded construction is replacing riveted. Minor shell repairs are made after each campaign. Principal causes of complete shell replacement are warpage and cracking resulting from localized over-heating. A 13x30 ft shell is being replaced after 34 years of operation and a total production of approximately 750,000 tons of blister. Converters are driven by 80 hp DC motors through company-designed worm gear reducers. Rotation is 0.38 rpm which permits the skimmer to spot the converter quite accurately for skimming slag. At three of the plants, protection against unscheduled air or power failures is afforded by the installation of emergency drives, consisting of auxiliary air motors or storage batteries. In order to avoid excessive splash out of the converters, the converter mouths are located as far back on the shells as existing flue facilities will permit. At one plant, the back of the mouth is only 13" to the rear of the vertical center line of the converter,. whereas it is 28" at another plant. Newly-lined mouth areas vary from 36 to 44 sq ft with effective operating areas about 25 pct less. It is important to keep the converter mouths as clean as possible. Dirty mouths create back pressures in the converters and as a consequence the tuyere air volumes are reduced. Mouths are generally cleaned by bumping with an empty ladle. Small mouth-cleaning rams have been used but unless extreme care is exercised the brickwork may be damaged. After considerable experimentation, the plants standardized tuyere elevations at 4 to 4% in. below horizontal center line at the shell with a downward pitch of about 13/16 in. per ft of length. Tuyeres are spaced at 6 in. centers except at the riding rings where there are no tuyeres. With this tuyere location, several of the plants now freeze magnetite slag in the bottoms, fronts, and backs up to the bottom of the tuyeres to control the internal shape of the converter. This has the effect of improving the agitation and mixing so that there is a marked increase in converting speed besides affording protection to the brick lining. Currently, the trend is to increase tuyere diameters from 1% to 2 in. to increase the air flow. At present, all converters are hand-punched but one converter is being equipped with a set of mechanical tuyere punchers. Rods for punching are % in. hexagonal smelter bar upset to ll/s in. and rods for cleaning tuyeres are upset to about 1% in., or larger, depending upon the tuyere diameter. Two of the plants use pneumatic reamers for cleaning the tuyeres between charges to minimize disturbing the coating on the inside of the refractory lining. Most of the puncher's platforms are pneumatically or hydraulically mounted so that a convenient punching position can be maintained regardless of tuyere position. For normal operations, tuyere air pressures vary from 15 to 13.5 psi, although some cycles such as magnetiting require pressures down to 8 psi. Air requirements vary from an average of 25,000 cfm on the newer installations down to 12,000 cfm on the older ones. Converter hoods are designed to protect the punchers from sparks, splash or hood accretions as well as to prevent the escape of objectionable

Jan 1, 1955

By H. W. Schull

The Alligator Ridge gold deposits are located in northwest White Pine County at the southwest end of Alligator Ridge. Alligator Ridge is on the west side of Long Valley in the range of hills that separates Long and Newark valleys. The nearest population center is Ely, about 113 km (70 miles) to the southeast. Access to the Alligator Ridge gold mine from Ely is via US Highway 50 and the Long Valley Ruby Marsh Road. The latitude and longitude is approximately 39° 45' north and 116° 30' west. The Alligator Ridge gold deposits occur in the lower 61 m (200 ft) of the Mississippian-Devonian Pilot Shale formation, a laminated calcareous carbonaceous siltstone. The gold deposits contain carbonaceous, oxide, and jasperoid type gold ore. For more details on the geologic features of the deposits, see Schull, Sutherland, and Ilchik (in press). The discovery story of Alligator Ridge began in the spring of 1976 when the areas mapped as jasperoid on the 1:250,000 scale geologic map of White Pine County (Hose and Blake, 1976) were examined and sampled. Seventeen samples, about 23 kg (50 lb), were collected from an area about 0.65 km2 (0.25 sq mile). Of these 17 samples 10 reported atomic absorption values of less than 0. 1 ppm Au and 7 reported values in the 0.1 to 1.0 ppm Au range. In June of 1976 20 lode claims were staked to claim the area of the rock chip sampling. The claims' end and side center lines were used as a grid for soil sampling. Sample stations were 91 m (300 ft) apart and sample lines were 229 m (750 ft) apart. The samples were sieved to - 180 µm (- 80 mesh). Out of 99 soil samples, seven samples reported Au values in the 0.1 to 1.0 ppm range. Of the seven auriferous samples, five were located over the jasperoid outcrops previously sampled; one over unmineralized Pilot Shale a few hundred m (ft) downslope from some Au-bearing jasperoid; and one from a 15 x 15 m (50 x 50 ft) talus outcrop area of hitherto unnoticed mineralized Pilot Shale. Subsequent sampling, mapping and drilling would show that this 15 X 15 m (50 x 50 ft) outcrop area was the top of the Vantage 1 ore body, about 1.27 Mt (1,400,000 st) of over 3 g/0.9 t (0.11 oz/st) Au. Late in the summer of 1976 about 30 more 1.4 to 2.2 kg (3 to 5 lb) rock chip samples were collected in the course of preliminary geologic mapping. This mapping and sampling showed that the gold-bearing jasperoids occurred at the contact between the Pilot Shale and the underlying Devils Gate Limestone. Rock chip samples of 0.1 ppm Au or greater were restricted to the jasperoids and the mineralized outcrop area of Pilot Shale located by the soil sample survey. Rock chip samples from the area of mineralized Pilot Shale were in the 3 to 5 ppm Au range. Activity resumed in the summer of 1977 with a more detailed soil geochemical survey. The jasperoid areas were defined as large geochemical gold anomalies of values greater than 0.1 ppm and locally greater than 0.2 ppm Au. Soil samples from the area of mineralized Pilot Shale outlined a greater than 0.1 ppm gold anomaly 61 x 152 m (200 x 500 ft) in size. Further geologic mapping showed that elsewhere, even where bleached and silicified, the Pilot Shale areas were geochemically very low in gold (less than 0.1 ppm Au). In November, 1977 twelve rotary percussion drill holes were drilled to test the gold-bearing jasperoid areas and the mineralized Pilot Shale area. Drilling of the jasperoid areas showed that the jasperoids gave way at shallow depths [less than 24 m (80 ft)] to unmineralized unaltered Devils Gate Limestone. A five hole cross pattern was drilled to test the area of mineralized Pilot Shale. Four of the five holes re-

Jan 1, 1985

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By W. O. Philbrook, R. S. Kaplan

Rates of oxidation were studied for levitation-melted samples of Fe-C, Fe-Si, Fe-C-Si, Fe-C-P, Fe-C-Mn, and Fe-C-S alloys oxidized by mixtures of either 5 or 10 pct O2, in helium at several temperatures in the range 1850o to 2050°C. The concentrations of the oxidized elements decreased linearly with time. Mass transport in the gas phase was found to be the rate-controlling step. Ilowever, a mulliple -film model was necessary to account for the flux of iron and manganese vapor counter to the oxygen flow. THE advent of the basic oxygen and spray-refining processes of steelmaking has generated considerable interest in the kinetics of reactions between oxygen-bearing gases and liquid iron alloys. The object of this research was the determination of the role of mass transport in the gas and metal phases and of surface chemical reactions in the overall oxidation process. Of the reactions for elimination of elements dissolved in liquid iron, the oxidation of carbon has been investigated most extensively. Studies by Fuji and Ura,1 Fuji,' and Gunji et a1.,3 done with pilot-scale basic oxygen furnaces, indicated that mass transport of gaseous oxygen was rate controlling when the metal carbon content was greater than 0.15 to 0.30 pct. When the carbon content was less than this critical amount, diffusion of carbon dissolved in the iron was thought to be rate limiting. L. A. Baker et a1.4,5 levitated samples of iron-carbon alloys and oxidized them in CO-CO2, CO-C02-He, and O2-He atmospheres at 1660°C. These investigators found that the metal carbon concentration decreased linearly with time and their samples exploded when the carbon content fell below about 0.8 pct. They concluded that the rate-limiting step was the transfer of oxidant to the gas-metal interface. A model based on this rate-limiting step predicted decarburization rates within a factor of two of those experimentally observed. The explosion of the samples was attributed to a shift in rate-controlling step from gas-phase mass transport to transport of carbon dissolved in the metal. L. A. Baker and R. G. ward6 and R. Baker7 used freely falling droplets to investigate oxidation kinetics. In both papers, the authors speculated that flame fronts may have been partially responsible for the lack of better agreement between experiment and theory. Swisher and Turkdogan8 oxidized liquid iron having an initial carbon content of 0.97 pct with CO-CO2 and CO-C02-Ar mixtures at 1580°C. They concluded that a surface reaction was the rate controlling step. Iron-silicon alloys have been oxidized by R. Baker7 and Filipov and Martynov.9 R. Baker 7 also studied iron-carbon-silicon alloys falling as liquid droplets through oxygen. He found that the rate of both carbon and silicon oxidation varied inversely with the drop radius. When the initial silicon concentration was greater than 6 pct, the samples cooled during their fall. Manganese oxidation has been studied by R. Baker,7 and by Filipov and Martynov.9 ward10 investigated the loss of manganese from liquid iron under vacuum. He found that mass transport of manganese vapor was rate limiting in argon atmospheres of 0.02 torr to 700 torr pressure. Iron-sulfur alloys were desulfurized with H2-He and H2-Ar mixtures by Peters et al.11 A model based on the transport of H2S from the gas-metal interface into the bulk gas gave fair agreement between the predictions of the model and the experimental results. EXPERIMENTAL TECHNIQUE Essentially, the technique consisted of using helium-oxygen gas mixtures to oxidize levitated samples of liquid binary and ternary iron-base alloys. The fused silica reaction tube is shown in Fig. 1. The coil design is similar to that of L. A. Baker et al.4'5 A Tef-lon-sheathed, ferritic stainless steel lifter (B) and an alumina pedestal (C) were used to support the sample in the coil prior to levitation and for the recovery of the sample. Samples were inserted into

Jan 1, 1970

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.' and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~' have reported the structure of

Jan 1, 1965

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont's exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim's discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By R. Bakish, M. A. Badiali, N. W. Kirshenbaum

One pound of ultra pul-e molybdenum has been produced containing both metallic and nonmetallic impuvities close to or less than the limits of detection. various purification methods were investigated; althouglz the use of move than one purification step was consideved, it was found that a single, caefully-controlled sublimation of MoCl5 yielded a highly puvified product without prior treatment or recourse to repeated sublimation. Hydrogen reduction of MoC1, to metal was attempted at atmospheric pressure; however, reduced pressure was necessary to obtain substantial yields. The tubular deposits of metal were consolidated into bulk fovm by electron beam melting undev high vacuum yielding a very low gas content. Boblems involved in monitoring the puvity of these materials and analytical results obtained are also presented. THE pronounced effect of even trace amounts of impurities upon fundamental properties of materials is well known to metallurgists and solid-state physicists. Consequently, groups interested in basic studies of metals have in recent years immensely stimulated the preparation and production of numerous ultra-pure metals. Increased demand by scientists for these high purity materials has necessitated development of facilities to prepare them in significant quantities; the procedures reported here were devised to produce significant quantities of ultra-pure molybdenum. Previous work performed in the field of vapor phase purification and hydrogen reduction of several other refractory metal chlorides had demonstrated valuable techniques applicable to molybdenum.' Various purification and reduction steps were individually investigated. Those procedures which showed the most favorable results with respect both to attainment of high purity and to ease of operation were then incorporated in the process utilized to produce the metal.' STARTING MATERIALS It is well known that because of differences in volatility, chlorides may be separated by fractional distillation. It was presumed that distillation of molybdenum pentachloride offered a simple and straightforward method of purification due to its relatively low boiling point. Alternatively, sublimation of the solid chloride also appeared feasible since MoC15 has both a reasonably narrow temperature range in which it exists as a liquid (a property typical of refractory metal chlorides) and a low enthalpy of sublimation. Pertinent thermochemical data of MoC15 are given in Table I. It should be noted that this compound must be handled with care as it is extremely hygroscopic. Anhydrous MoC15 was obtained from the A Metal Climax Co. METHODS OF PURIFYING MOLYBDENUM PENTACHLORIDE Distillation. It was expected that distillation methods, while affording an efficient purification, would prove simple to control and would have a higher production rate than sublimation processes. Also considered was the possibility of effecting a high degree of purification by using both these volatilization methods in conjunction—possibly a distillation followed by sublimation of the solidified condensate. Distillation of MoC15 was investigated using a single stage distillation column packed with chemically resistant glass beads. Heating coils were wound around the column and collection tube (condenser). As-received MoCl5 was charged into a flask connected with the column using a side loading arm under an argon flow. After the column and condenser were brought to about 270" and 210°C, respectively, the apparatus was lowered until the flask was fully immersed in a constant temperature fused salt bath maintained at about 285 °C. Distillation was continued for about 10 or 15 min until 50 to 70 g of distillate had been collected. Analyses of these distillations indicated that several elements, e.g., Cu, Fe, Ni, Cr, and Mg, were lowered in quantity although not all were removed to the same extent. The occurrence of Na, B, Si, and A1 in the distillates appeared to be due to contamination, possibly from corrosion of the pyrex glass. An improved distillation system of larger capacity and longer distilling column was built. Improvements were effected in lowering the amounts of such impurities as B, Mn, Ni, Na, Mg, Cr, Cu, and Fe. These studies were pursued concomitantly with efforts to purify by sublimation; it was subsequently found that although improvements in purity were obtained by distillation, sublimation processes were simpler to control and effected a high degree of purity.

Jan 1, 1963

By Peter Beardmore, Michael B. Bever

The effects of the temperature of deformation and the degvee of deformation on the annealing spectrum of a Au-Ag alloy have been determined by vesistance measurements. Specimens were deformed in torsion at 4°, 78K and room temperature up to strains nd/l of about 1.0 and were isochronally annealed. Discrete annealing stages similar to those found for pure metals were observed. Stage A occurred below room temperature; the decrease in reszstance associated with this stage increased as the temperature of deformation was lowered or the strain was increased. Stage B manifested itself as an increase in resistance; this is attributed to the restoration of short-range order promoted by vacancy or vacancy aggregate migration. At temperatures above 48S0K, recrystallization or Stage C occurred. Stages A, B, and C in the annealzng curves of this alloy may be considered to correspond to Stages II, Ill, and V, respectively, in the terminology used to describe the annealing spectrum of pure metals. ThE annealing behavior after deformation below room temperature has been thoroughly investigated on pure metals, in particular gold and copper. The occurrence of several discrete stages in the annealing spectrum of these metals has been established, but the interpretation of some of these stages in terms of specific mechanisms is still controversial.' The annealing of alloys deformed below room temperature has been the subject of only a few investigations. In the investigation reported here, a Au-Ag alloy was annealed after deformation at and below room temperature. This continues a research program on the deformation and annealing behavior of Au-Ag alloys.2-8s EXPERIMENTAL PROCEDURE An alloy rod of composition 82.6 wt pct Au-17.4 pct Ag was reduced to wire, 0.0428 in. diam, by swaging and drawing. After a recrystallization treatment, the grain size was 0.031 mm, as obtained from the average linear intercept.7 The ends of wires about 6 in. long were flattened and sealed into short brass tubes with cold setting cement to form the grips of the torsion specimens. The equipment used for deformation has been described elsewhere.6 The specimens were deformed at room temperature, 78", and 4°K to various strains nd/l, where n is the number of turns, d the diameter of the specimen, and 1 its length between grips. The strain rate ?max was 0.1 min-' at the sur- face of the specimen except where noted otherwise. The specimens were annealed isochronally for 30 min at intervals of approximately 30°K from the temperature of deformation to approximately 800°K, except that after deformation at 4°K the lowest annealing temperature was 78°K. A potentiometric method was used to measure the resistance: all measurements were made at 78°K with the exception of some measurements at 4°K mentioned below. Data obtained with a single specimen yielded a complete annealing curve: in several cases duplicate specimens were used to confirm the reproducibility of the curves. Since the surfaces of the specimens were rough after deformation, their diameters could not be measured accurately. The resistance increments after deformation and annealing are therefore reported as percentages of the resistance of the same specimen measured after completion of the annealing, that is, after full recrystallization. The corresponding resistivity values can be calculated by obtaining the effective diameter of a deformed specimen from the ratio of its resistance after recrystallization to the true resistivity, which was determined with a smooth specimen of known dimensions. This method of calculation was used to obtain data shown in several of the figures. RESULTS AND DISCUSSION The isochronal annealing curves after deformation to various strains at 4", 78K, and room temperature are shown in Figs. 1, 2, and 3, respectively. The resistance increment of the as-deformed specimens as a function of strain is shown in Fig. 4. For the specimens deformed at 4°K. values measured at 78°K are plotted with the exception of those for the as-deformed

Jan 1, 1970

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By C. E. Hottman, R. K. Johnson

Fluid pressure within the pore space of shales can be determined by using data obtained from both acoustic and resistivity logs. The method involves establishing relationships between the common logarithm of shale transit time or shale resistivity and depth for hydrostatic-pres-sure formations. On a plot of transit time vs depth, a linear relationship is generally observed, whereas on a plot of resistivity vs depth, a nonlinear trend exists. Divergence of observed transit time or resistivity values from those obtained from established normal compaction trends rinder hydrostatic pressure conditions is a measure of the pore fluid pressure in the shale and, thus, in adjacent isolated permeable formations. This relationship has been empirically established with actual pressure measurements in adjacent permeable formations. The use of these data and this method permits the interpretation of fluid pres.rure from acoustic and resistivity measurements with an accuracy of approximately 0.04 psilft, or about 400 psi at 10,000 ft. The standard deviation for the resistivity method is 0.022 psi/ft, and for the acoustic method 0.020 psi/ft. Knowledge of the first occurrence of overpressures, and of the precise pressure-depth relationship in a geologic province, enab1es improvements in drilling techniques, casing progroms, completion methods and reservoir evalzmtions. INTRODUCTION CENKRAL STATEMENT Operators engaged in the search for and production of hydrocarbon reserves in Tertiary basins are more and more frequently confronted with complications associated with over pressured (abnormally high fluid pressure) formations. This is particularly true in the Texas-Louisiana Gulf Coast area. The problems associated with these formations are of direct concern to the combined activities of all phases of operations, i.e., geophysical, drilling, geological and petroleum engineering.' - Knowledge of the pressure distribution of a given area of operations would greatly reduce the magnitude of many of these complexities and in some cases would completely eliminate specific problems. his pape; presents techniques developed for estimating formation pressures from interpretations of acoustic and electric log data. Specifically: the acoustical and electrical properties of shales, reflected by conventional acoustic and electrical surveys, can be used to infer certain reservoir properties, such as formation pressure, at any level in a well. It has been possible to develop these techniques because of a firm understanding of the basic principles that govern and apply to such overpressured provinces. NORMAL PRESSUKES Normal pressures refer to formation pressures which are approximately equal to the hydrostatic head of a column of water of equal depth. If the formations were opened to the atmosphere, a column of water from the ground surface to the subsurface formation depth would balance the formation pressure. On the Gulf Coast, the shallow, predominantly sand formations contain fluids which are under hydrostatic pressure. These formations are said to be normally pressured or to have a normal pressure gradient.* Experience has shown that the normal pressure gradient on the Gulf Coast is approximately 0.465 psi/ft of depth. OVERPRESSURES Formations with pressures higher than hydrostatic are encountered at varying depths in many areas. These formations are referred to as being abnormally pressured, abnormally high pressured, or overpressured. Formation pressures up to twice the hydrostatic pressure have been observed. These formations require extreme care and much expense to drill and to exploit. COMPACTION-FLUID PRESSURE RELATIONS THEORY The generation of overpressured formations in Tertiary sections of the Gulf Coast and several other Tertiary sedimentary basins is, in general terms, considered to be primarily the result of compaction phenomena.' This portion of the paper presents a brief review of the theory which associates compaction and fluid pressure relations, and should thus provide the necessary background for an understanding of the techniques presented. See Hubbert and Rubey' for a more comprehensive treatment of this subject. The theory of the consolidation of a water-saturated clay' has been well established by workers in soil mechanics. The concept is explained by a model with perforated metal plates separated by metal springs and water and enclosed in a cylindrical tube. Fig. 1 is a schematic representation of such a model (see Ref. 5, Fig. 27, page 74). The springs simulate communication between clay particles, and the plates simulate the clay particles. Mano-

Jan 1, 1966

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953