Search Documents

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

By Charles Willard Hayes

Shortly after the discovery of black phosphate on Swan creek, in Hickman county, Tennessee, prospectors familiar with the Florida phosphate came to the region and began the search for rock similar to that found in Florida. Among these was Mr. E. Slattery, who located at Linden, in Perry county. He gave a piece of the Florida rock to Mr. C. C. Sutton, and the latter discovered on Tom's creek a deposit which bore a strong

Jan 1, 1896

By D. N. Williams

THE present study was undertaken with two specific objectives: measurement of the thermal-expansion coefficient of ß titanium and examination of the effect of solid-solution alloying on the thermal expansion coefficient. Four titanium alloy niaterials were available in the form of annealed 5/8-in. diam rod. Three of these, Ti-8V, Ti-20V, and Ti-6A1-4V, were prepared in the laboratory from 140 Bhn sponge. The

Jan 1, 1962

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By Joseph D. Weeks

The primary problems of civilization are material ones; their answers are writ in fire. When these problems in their higher aspects have pressed for solution, it has been out of the burning bush that the Divine voice has spoken, or in the cloud and smoke that the Divine finger has traced the rules by which these problems shall be solved. It is with the material problems, however, that we, as engineers, have to deal.

Jan 1, 1896

By Om P. Pande, Larry S. Diaz

Modern mineral processing plants could not operate efficiently, or even exist, without instruments which indicate, record, control, and in some cases anticipate the many changes that occur in a process. Even in plants which are operated manually, instruments are used to tell the operator when he should turn a valve or press a handswitch. Accordingly, all mineral processing plant engineering and construction projects must give careful consideration to this area of design activity.

Jan 1, 1978

Although the mining industry faced ever-increasing risks and uncertainties in 1974, it nevertheless pushed ahead with considerable rapidity in exploring and developing new orebodies-while expanding and improving the technologies of mining and exploration. Prepared by the SME Mining and Exploration Division, this section of the annual review covers the pertinent worldwide developments in the fields of geochemistry, geology, geological engineering, open pit mining, underground mining, rock mechanics, operations research, and solution mining.

Jan 2, 1975

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By S. G. Cupschalk, J. J. Wert, R. A. Buchanan

The uniaxial deformation of thermally ordered and disordered polycrystalline Cu3Pt was studied by means of the X-ray line - broadening analysis according to Warren and Averbach and the extension of this analysis to ordered fcc materials by Mikkola and Cohen. Because of the heat treatment history, extinction had a pronounced effect on the X-ray spectra of ordered and disordered C%Pt at small plastic strains. After an appropriate correction for extinction, the long-range order in thermally ordered ChPt was found to decrease at a slow constant rate with plastic strain. Furthermore, the antiphase domain probability increased at a constant rate to 17.5 pct strain. The effective particle size behavior indicated that the stacking fault energy is lower in ordered than in disordered Cu3Pt. Analysis of the stress-strain curves shouled that ordered Cuzt has a slightly lower yield Point but a much higher work-hardening rate than disordered Cu3Pt. THE presence of long-range order in a solid-solution alloy has a marked effect on its mechanical properties. While this effect has been known qualitatively for many years, it was not until recently that detailed investigations have been performed to determine the exact role long-range order plays in this strengthening mechanism. The development of an advanced, quantitative. X-ray diffraction analysis by Warren and Averbachl and the extension of this analysis to the L1, type super lattice by Mikkola and cohen2 have greatly accelerated research in this field. The research reported in this paper consisted of two primary phases. The first phase was to determine the effect of long-range order on the tensile properties of polycrystalline Cu3Pt. This objective was accomplished by comparing the stress-strain behavior of thermally ordered CusPt to that of thermally disordered CusPt. The second phase of the research was to determine the difference between the atomic arrangements in thermally ordered and thermally disordered Cu3Pt as a function of uniaxial deformation and thereby gain a deeper insight into the mechanism by which long-range order affects the tensile properties. This second objective was accomplished by applying the Warren-Averbach method of peak profile analysis to the X-ray diffraction patterns obtained from ordered and disordered Cu3Pt after given amounts of uniaxial deformation. EXPERIMENTAL PROCEDURE The Cu3Pt was prepared by vacuum melting and casting. After a homogenization anneal, the ingot was cold-rolled to sheet form. Two tensile specimens with gage sections of 2.50 by 0.500 by 0.115 in. were carefully machined from the sheet. The specimens were polished with a final step of 600-grit paper to insure smooth diffracting surfaces. Finally, one specimen was heat-treated to yield an average grain diameter of 0.016 mm and an initial degree of long-range order, S, of 0.825. The other specimen was water-quenched from above the critical temperature, 645"C, to yield an average grain diameter of 0.017 mm and zero long-range order. The heat treatment history of each specimen is shown in Table I. The tensile tests were performed utilizing a Research Incorporated Model 900.95 Materials Testing System. This unit employs a closed-loop feedback system which maintains a constant strain rate through an extensometer clipped to the gage section of the tensile specimen. A strain rate of 1.32 i0.02 x 10"4 sec-' was employed in testing both specimens. In the X-ray diffraction analysis, a General Electric XRD-5 diffractometer equipped with a pulse-height analyzer set for 90 pct efficiency was employed. The goniometer speed selected was 0.2 deg, 20, per min. Filtered Cu radiation was used for all peaks and all peaks were chart-recorded. Because of nonuni-form grain size. it was necessary to spin the specimens during X-ray analysis in order to obtain reproducible integrated intensities. The spinning rate was 2000 i100 rpm. The application of the Warren-Averbach method of peak broadening analysis to a diffraction pattern is very time consuming if done manually. In this research, the calculations involved were performed with the aid of a computer program by wagner.3 As reported by Wagner, the program is written in Fortran TV computer language. It was modified to Fortran I1 so as to be handled by the IBM 7072 computer at Van-derbilt University. In the X-ray diffraction analysis of uniaxially deformed Cu3Pt, the 100, 200. 400. 111, and 222 reflections were recorded from the initially ordered sample after 'plastic strains of 3.0, 6.0, 9.0, 12.0,

Jan 1, 1970

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By E. B. Fitch, E. C. Johnson

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool. BY now most engineers are familiar with the liquid-solid or Dutch State Mines cyclone. However, it should be helpful to know exactly what it is that the equipment does and what its limits are. Without going into cyclone theory, this paper will describe the operating characteristics of Dutch State Mines cyclones. These are manufactured under license in this country and sold under the trade-marked name of DorrClone. The physical construction of the liquid-solid cyclone has been covered in many papers,'-' the DorrClone in particular being described in some detail by Weems. Fig. 1 shows the unit in cross-section. The feed enters at C. The coarse, heavy particles are thrown centrifugally to the periphery and make their way down the wall to the apex where their rate of discharge as underflow is controlled by an adjustable rubber apex valve. As the apex diameter is decreased the solids build up behind the valve, producing a denser underflow. Meanwhile the fine particles are swept into the upward flowing vortex stream which exits as overflow through the vortex finder, F. Flexibility to produce the specific result desired in a particular process is achieved by providing means for varying the areas of the entrance, vortex discharge, and apex discharge. The entrance area may be varied by insertion of special shims. Vortex discharge area may be changed by use of different-sized vortex finders which are interchangeable. Similarly, the different sizes of apex valves are interchangeable and in addition each apex valve is variable down to about 60 pct of its maximum diameter. A most significant primary distinction to make is that although liquid-solid cyclones have been sometimes called thickeners, they actually are classifiers, and very potent ones. They are almost never thickeners in the special sense that many metallurgical engineers understand the term. There would be no profit in quibbling over the definition of a word, but when the application of cyclones is considered, it will help to understand the difference be- tween two mechanisms, one of which will be called classification, and the other thickening. In what is called thickening the fine solid particles present in the feed hold together by surface attraction during the sedimentation process. The loose network of particles thus held together constrains all particles to settle at approximately the same rate, the larger ones dragging the smaller ones down. As a result, pulp settles with a sharp line of demarcation between solids and a relatively clear supernatant liquid. Essentially all the solids, regardless of their fineness, pass into the thickened underflow, and a clear overflow is separated. In classification, on the other hand, the interparti-cle forces are relatively insignificant as compared to the settling force on the individual particles, and are insufficient to prevent independent movement of the particles. The coarsest, heaviest particles settle most rapidly through the pulp, passing more slowly settling fines. Particles coarser than the mesh-of-separation essentially all settle into the underflow, but if the feed contains any particles finer than the mesh of separation, at least part of them will appear in the overflow. A clear supernatant or overflow can be obtained only if there are no undersize particles present in the feed. Thus it will be seen that classification is impossible under ideal thickening conditions. The finer particles are pulled down at essentially the same rate as coarser particles, and there is no separation on the basis of particle size. The surface attraction holding the particles together in a thickener is usually feeble. Whenever the sedimentation force on any particle is strong with respect to the interparticle forces, that particle can pass through the tenuous structure and settle independently. There are at least four ways of making the sedimentation force strong, with respect to the interparticle forces, and obtaining classification. First, and most obvious, the particles may be large and heavy. Thus coarse sands settle out in a beaker or Dorr thickener ahead of the rest of the thickening solids. Second, the interparticle forces may be altered by physicochemical means; i.e., it is often necessary to add dispersing agents to destroy the interparticle forces and permit classification to take place. Third, the interparticle forces may be reduced by dilution of pulp. It is well known that to obtain the most efficient separation of

Jan 1, 1954

By E. W. Filer, L. S. Darker

ONE of the primary purposes of this investigation was to determine how far blast-furnace metal and slag depart from equilibrium, particularly with respect to sulphur distribution. In studying the equilibrium between blast-furnace metal and slag, there are two approaches that can be used. One method is to use synthetic slags, as was done by Hatch and Chipman;' the other is to equilibrate the metal and slag from the blast furnace by remelting in the laboratory. In the set of experiments here reported, metal and slag tapped simultaneously from the same blast furnace were used for all the runs. The experiments were divided into two groups: 1—a time series at each of three different temperatures to determine the t.ime required for metal and slag to equilibrate in various respects under the experimental conditions of remelting, and 2—an addition series to determine the effect of additions to the slag on the equilibrium between the metal and slag. An atmosphere of carbon monoxide was used to simulate blastfurnace conditions. The furnace used for this investigation was a vertically mounted tubular Globar type with two concentric porcelain tubes inside the heating element. The control couple was located between the two porcelain tubes. The carbon monoxide atmosphere was introduced through a mercury seal at the bottom of the inner tube. On top, a glass head (with ground joint) provided access for samples and a long outlet tube prevented air from sucking back into the furnace. The charge used was iron 6 g, slag 5 g for the time series, or iron 9 g, slag 7 % g for the addition series. This slag-to-metal ratio of 0.83 approximates the average for blast-furnace practice, which commonly ranges from about 0.6 to 1.1. A crucible of AUC graphite containing the above charge was suspended by a molybdenum wire in the head and, after flush, was lowered to the center of the furnace as shown in Fig. 1. The cylindrical crucible was 2 in. long x % in. OD. The furnace was held within &3"C of the desired temperature for all the runs. The temperature was checked after the end of each run by flushing the inner tube with air and placing a platinum-platinum-10 pct rhodium thermocouple in the position previously occupied by the crucible; the temperature of the majority of the runs was much closer than the deviation specified above. The couple was checked against a standard couple which had been calibrated at the gold and palladium points, and against a Bureau of Standards couple. The carbon monoxide atmosphere was prepared by passing COz over granular graphite at about 1200°C. It was purified by bubbling through a 30 pct aqueous solution of potassium hydroxide and passing through ascarite and phosphorus pentoxide. The train and connections were all glass except for a few butt joints where rubber tubing was used for flexibility. The rate of gas flow was 25 to 40 cc per min. As atmospheric pressure prevailed in the furnace, the pressure of carbon monoxide was only slightly higher than the partial pressure thereof in the bosh and hearth zones of a blast furnace—by virtue of the elevated total pressure therein. Simultaneous samples of blast-furnace metal and slag were taken for these remelting experiments. The composition of each is given in the first line of Table I. There is considerable uncertainty as to the significant temperature in a blast furnace at which to compare experimental results. This uncertainty arises not only from lack of temperature measurements in the furnace, but also from lack of knowledge of the zone where the slag-metal reactions occur. (Do they occur principally at the slag-metal interface in the crucible, or as the metal is descending through the slag, or even higher as slag and metal are splashing over the coke?) The known temperatures are those of the metal at cast, which averages about 2600°F, and of the cast or flush slag, which is usually about 100°F hotter. To bridge this uncertainty, remelting temperatures were chosen as 1400°, 1500" (2732°F), and 1600°C. For the time series the duration of remelt was 1, 2, 4, 8, 17, or 66 hr; crucible and contents were quenched in brine. The addition series were quenched by rapidly transferring the crucible and contents from the furnace to a close-fitting copper "mold." Of incidental interest here is the fact that the slag wet the crucible

Jan 1, 1953

By J. Winlock

To have been chosen by you to give the Howe Memorial Lecture is the greatest honor I have ever had and I should like to have you know that I appreciate it deeply. Many years ago I had the privilege and the pleasure of working with Professor Howe in the private laboratory which he had established in his home at Bedford Hills, New York. Without doubt he was one of the world's greatest metallurgists and so you can imagine what a difficult task it has been for me to live up to his teachings. Every morning Professor Howe would outline the work he wanted done and the recollections of those conferences are clear to me to this day. Sometimes he would ask me to ride in his automobile and the chauffeur had full instructions to go no more than fifteen miles an hour. If he did so, Professor Howe was sure to rap upon the man's shoulder with his cane. I assure you, however, Professor Howe's thinking was not at that rate. His homely advice, his patience and his perfect control of the English language still impress me. Many times I heard him dictate a complicated paper on metallurgy and never find it necessary to change a single word. There are no better words to describe the character of Professor Howe, in my opinion, than those used by Professor Sauveur when he presented the John Fritz Medal to him in 1917: "Lover of justice and humanity Public servant and public benefactor, Master of the English Language, Loyal and devoted friend, Untiring and unselfish worker in an important field of science." I hope you will bear with me with the same patience and understanding which he used to give to me. The peculiar behavior of steel at the yield point has long been known and has been the subject of much research, both in this country and abroad.',' Many theories, including some of mine and my colleagues, have been suggested, but none of them, in our opinion, fully explains to our satisfaction why the phenomena occur. Of particular importance has been the work of Nadai,3 Siebel and Pomp,' Sachs and Fiek,5 Rawdon,0 Kenyon and Burns,' Gensamer," Gensamer and Meh1,0 Davenport and Bain,'" Fell," Deutler,12 Brinkman,13 MacGregor,14 Hollomon,15 Cot-trell,16 and Palm." The question of what is occurring during this singular behavior is not only of interest from an academic point of view, but is of great practical importance for at least two reasons: 1—The highly localized plastic flow which occurs during the deep drawing of light-gage steel gives rise to surface markings which seriously mar its appearance, Fig. 1. If the forces causing the deformation are primarily tensile forces, these surface markings occur as depressions in the surface. Whereas, if the forces causing the deformation are primarily compressive, irregular lines of elevations occur. These surface markings are known as Luder's lines, Hartmann lines, the Piobert affect, and, in the shop, as "stretcher strains." 2—The steel is in the most suitable condition for deep drawing after the yield point phenomena have been removed. When this is done, the steel may be deep drawn more easily and to a greater extent.' It should be mentioned that steel is not the only metal which shows this peculiar behavior at the yield point. Stretcher strains occur, also, during the deformation of some copper-nickel-zinc alloys." The purpose of this paper is not an attempt to describe what causes the steel to behave in this peculiar manner, but an attempt: l—to describe what is taking place at the yield point; and 2—to show the influence of the rate of deformation on the tensile properties of some plain carbon steels. As is well-known, there are two methods of deforming a metal in tension: 1—by actually hanging an increasing amount of dead weight on the metal; or 2—by deforming the metal at some given rate or rates by means of oil pressure cylinders, screws, etc. With the first method, the load is always present and, clearly, no drop in load can ever occur while the steel is deforming. With the second method, the registered load is the resistance of the steel to the deformation being imposed upon it. The second method is the one most widely used, and is the one referred to throughout this paper. In order to describe clearly what is occurring at the yield point in steel, it will help, I believe, if a description is first given of what occurs when alumi-

Jan 1, 1954

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

By W. S. Reid

In March, 1938, E. P. Fleming, metallurgist for the American Smelting and Refining Co. inaugurated an investigation into the possibilities of recirculating the gases from Dwight-Lloyd sintering machines operating on lead charge, with the twofold object of concentration of the SO2 content and reduction in volume of total gas produced. The possibility of recovering a commercial grade of SO2 gas from D & L machines operating on lead charge had previously been considered by several investigators. Early History of Recirculation The Selby Smelter Commission Report, published by the Bureau of Mines in 1914, contains a chapter by A. E. Wells regarding results obtained at Selby, wherein some of the richer gas was recirculated through a hood over the pallets. Oldright and Miller of the U. S. Bureau of Mines had also made tests at Trail, B.C., and at Kellogg, Idaho. R. C. Rutherford, while at the Chihuahua, Mexico, Smelter of the American Smelting and Refining Co., in May, 1937, proposed recirculation of D & L gases to decrease the volume of gas handled by the baghouse. At none of these plants, however, was the operation commercialized. In July, 1938, Mr. Fleming, in correspondence with the Selby Plant, inquired regarding the possibility of obtaining 6 pct SO2 gas from the Selby D & L machines. At that time, the writer advised that there was slight possibility of obtaining 6 pct SO2 gas without re- circulation, but believed that it was possible with recirculation, and that experimental work toward that end should be tried at some plant where spare D & L machines were available. The foregoing statement was based on the following information then available— 1. Tests on Selby first-over machines showed 2.28 pct SO2 from first windbox and 1.03 pct SO2 from second windbox, and corresponding figures for second-over charge of 0.81 pct SO2 for first windbox and 0.08 pct SO2 for second windbox. 2. Oldright and Miller (US. Bureau of Mines) in 1932 at Bunker Hill, on 42 in. X 22 ft machines found: a. First-over charge—Maximum SO2 concentration (leaving cake) of 9.5 pct. b. First-over charge—SO2 concentration of over 8 pct from the 4 ft to the 12 ft points beyond the front dead-plate and that the concentration then dropped rapidly. c. That approximately 80 pct of the total sulphur eliminated on the second-over machines occurred during the travel of the pallets from the 1 ft to the 6 ft distances from the dead-plate. d. That approximately 94 pct of the total sulphur eliminated on the second-over machines occurred over the first windox. 3. Oldright and Miller (US. Bureau of Mines) in 1932, at Trail, on 42 in. X 50 ft machines found: a. First-over charge—SO2 varied from 2.0 pct to 5.5 pct (leaving cake) from the 12 ft to 28 ft points from the deadplate. b. That the average SO2 increased from 1.0 pct at 7 ft from dead-plate to maximum of 3.3 pct at 20 ft, then dropped to 1.5 pct at 40 ft. c. That on a 22 ft, second-over machine with an 11 in. bed the SO2 varied from 4.5 pct to 6.5 pct from the 2 ft to the 8 ft points from the dead-plate. d. That on the final roast, the SO2 concentration also varied across the pallets; that is, 2 1/2 pct at the side, increasing to 6.0 pct, 5 in. in, and to 7.0 pct at 10 in. to 20 in. in, then decreased vice versa at the opposite side. e. Concluded that most of the sulphur on a 22 ft machine was removed over the first 7 ft of the first windbox; therefore, they partitioned the first windbox so that the exit gas from the second 4 ft section was returned to the surface of the pallets over the fist 7 ft section, and during a seven-day trial the gas from the 4 ft section averaged 2.4 pct SO2, while the recirculated gas from the first 7 ft section only increased to 3.8 pct SO2. (Excess suction over the 7 ft section to prevent escape of SO2 laden gas from the 4 ft section caused dilution by air.)

Jan 1, 1950

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery's5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale's results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists' attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.' At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley's paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By W. C. Hauber

Techniques previously published to predict the production performance of a water flood when the mobility ratio is not unity have been primarily restricted to a five-spot well pattern. When other types of well patterns are considered, the prediction of performance has required either a model study or a complex numerical solution of a multiple-fluid system with a high-speed digital computer. Simple methods are developed in this report for predicting the areal sweep efficiency and injectivity history of a water flood for arbitrary well patterns and mobility ratios. The effect of an initial gas saturation can be incorporated into this method of prediction. With the layer superposition concepts published by Prats, et al.,1 these methods can be used to predict the production performance of a water flood in a reservoir having a wide range in permeability. A reasonably good agreement is shown by comparisons of the results calculated by this method with those obtained either by model studies or by complex numerical solution of multiple-fluid systems. Therefore, it has been concluded that a reasonably accurate method has been developed for predicting the production performance of a water flood employing an arbitrary type of well pattern for any given mobility ratio. A medium-speed digital computer can be used in applying this method. INTRODUCTION Production performance of multi-fluid five-spot water floods can be predicted by the techniques published by Prats, et al.1 This technique takes into account the effects of initial gas saturation, mobility ratio and vertical variations in horizontal permeability. A basic assumption in applying this technique is that unit displacement efficiency does not vary with time after the passage of the flood front. Prats, et al. demonstrated that this assumption is valid for normal waterflood applications with small mobility ratios. To extend Prats' technique to other types of well patterns has required either an experimental model study or a numerical solution of a multiple-fluid system to describe the performance of an individual homogeneous layer. Sheldon and Dougherty2 presented an exact numerical solution employing any arbitrary well pattern. This technique is complex to apply, requiring (1) numerical solution of the single-fluid system, (2) conformal mapping of the streamlines and iso-potential lines to form a new grid network, and (3) a numerical solution of the multi-fluid system on the new grid network. A method was developed in this paper to approximate areal sweep efficiency and injectivity as functions of time for an individual homogeneous layer for arbitrary well patterns and mobility ratios. Analytic expressions were derived to directly apply this method to five-spot and direct line drive well patterns. For other types of well patterns, this method is similar to the approach of Higgids and Leighton,6 in that it utilizes the stream tubes and iso-potential lines obtained by the solution of differential equations when the mobility ratio is unity. However, this method is easier to apply than the Higgins-Leighton method since it does not require knowledge of the variation between oil and water relative permeabilities and saturation. Using the relationship between areal sweep efficiency, injectivity and the volume of water injected into an individual homogeneous layer as obtained by the method presented in this paper, and Prats' technique for the superposition of individual layers, one can predict the production performance of any water flood. ASSUMPTIONS GENERAL Basic assumptions made in this report are that fluids are incompressible and the layers are horizontal, homogeneous and uniformly thick. It is assumed that as water is injected into the layer, three distinct regions are formed —a water bank, an oil bank, and an unflooded region. Each region is assumed to displace other regions in a pis-tonlike manner, with only one fluid flowing in each region, so that there is no change in unit displacement efficiency with time after the flood front has passed in the reservoir. Therefore, the residual oil saturation in the water bank and the oil saturations in the unflooded region are constant throughout the layer. The ratio (F) of the bulk volume of a layer occupied by the oil and water banks at any time before oil breakthrough, to the corresponding bulk volume of a layer occupied by the water bank, is given' by the equation BREAKTHROUGH AREAL SWEEP EFFICIENCY To predict the behavior of any type of waterflood pattern, one must know the breakthrough areal sweep efficiency Eb(Mc,o, F) for the pattern for any water:oil mo-

Jan 1, 1965

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961