Search Documents

By S. P. Howell, F. B. Foley

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world's notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world's great mines.

Jan 1, 1981

By J. T. Norton, A. L. Mowry

S. J. SINDEBAND*—(1) Discussing the properties of the powders used, Mr. Rostoker mentioned a silicon powder as being between 150 and 325 mesh. We always had much difficulty in measuring particle size of silicon powder by screen analysis, because of its tendency to agglomerate. I would be interested in the method used to measure these particle sizes. (2) Mr. Rostoker maintains that the measurement of magnetic properties is more accurate in determining complete homogenization of an alloy, than is the X ray diffraction technique. I wonder whether this is really true. Even when diffusion is complete, magnetic properties will change during continuation of the heat treatment, due to change in density and pore shapes, as has been demonstrated by Mr. Rostoker himself. Which effect is faster, the diffusion of the alloy components or the attainment of final density, will, in my opinion, depend very much on initial material and sintering conditions used. For magnetic applications, of course, the magnetic measurements are most suited for determining the point at which equilibrium conditions are reached. (3) I was glad to see that Mr. Rostoker had used sample sizes which are similar to those I had used previously, and I believe that ring samples of about 2 in. od will become more or less standard samples for the determination of magnetic properties of powder metallurgy products. I should like to ask how the density was changed for the samples on which the effect of porosity was investi- gated, and, further, why the sintering temperature used for this series of experiments was so low. It is somewhat surprising that a 24-hr treatment at 850°C acts so much more to spheroidize the pores than a treatment for 1 hr at 1100°C. But the effect seems to be indisputable. I have made an investigation of the influence of sintering temperature for longer times on the maximum permeabilities of iron powder compacts which was presented at the International Powder Metallurgy Conference in Graz, in 1948, and I hope that these results will be published here within a short time. The results of this investigation are confirmed by Mr. Rostoker's findings that the change of time from 1 to 24 hr changes the permeability behavior considerably in the direction as indicated by Polder and Van Santen for spheroidiza-tion of pores. I do not quite understand Mr. Rostoker's explanation of the influ-

Jan 1, 1950

The U. S. Navy Department has perfected plans for the enrollment and training of considerable numbers of engineering officers. A school for this purpose, the U. S. Navy Steam Engineering School, has been established by the Department at Hoboken, N. J. The school is open to men between the ages of 21 and 40 who meet the physical requirements of the Navy, who are of thorough ability and officer-like character and who have completed the mechanical or electrical engineering course at certain recognized technical schools, or who possess an education and experience adjudged to be an equivalent thereof. Enrollment in the U. Naval Reserve Force of men properly qualified may be made at any Naval enrolling office, notation being made of the applicant's qualifications and desire to be detailed to this school. Applicants will be enrolled as Chief Machinist Mates, and during the course of instruction will draw the pay of this rating, $83 per month, plus $60 per month paid as subsistence. Upon graduation, men will be commissioned as Ensigns in the U. S. Naval Reserve, with a salary of $1700 per year. The duty to which a graduate of this school will be assigned will be that of an engineer officer in the auxiliary service of the Navy. Special provision has been made for the continuance of the school with proper material by a Navy regulation which permits undergraduates of the Freshman, Sophomore, and Junior Classes in recognized engineering schools to enroll in the Naval Reserve Force with the rating of Seaman 2d Class, and continue their courses at the institutions where they have matriculated. Such men will be called into active service after their graduation, and can at that time, if they are qualified to pass an officers' physical examination, apply for admission to the U. S. Navy Steam Engineering School. Men who are registered in the draft, either graduates or undergraduates, may enroll with the proper enrolling officer by securing from their draft board a letter of release, which in all probability can be obtained for this purpose. The aim of this school is not simply to produce engineers, but to produce naval engineering officers in the true sense of the word. The course of instruction covers a period of five months, arranged in four periods.

Jan 10, 1918

By Edward Salisbury Dana

THE remarkable advance in the Science of Mineralogy, during the years that have elapsed since this Text-Book was first issued in 1877, has made it necessary, in the preparation of a new edition, to rewrite the whole as well as to add much new matter and many new illustrations. The work being designed chiefly to meet the wants of class or private instruction, this object has at once determined the choice of topics discussed, the order and fullness of treatment and the method of presentation. In the chapter on. Crystallography, the different types of crystal forms are described under the now accepted thirty-two groups classed according to their symmetry. The names given to these groups are based, so far as possible, upon the characteristic form of each, and are intended also to suggest the terms formerly applied in accordance with the principles of hemihedrism. The order adopted is that which alone seems suited to the demands of the elementary student, the special and mathematically simple groups of the isometric system being described first. Especial prominence is given to the "normal group" under the successive systems, that is, to the group which is relatively of most common occurrence and which shows the highest degree of symmetry. The methods of Miller are followed as regards the indices of the different forms and the mathematical calculations. In the chapters on Physical and Chemical Mineralogy, the plan of the former edition is retained of presenting somewhat fully the elementary prin¬ciples of the science upon which the mineral characters depend; this is par¬ticularly true in the department of Optics. The effort has been made to give the student the means of becoming practically familiar with all the modern methods of investigation now commonly applied. Especial attention is, therefore, given to the optical properties of crystals as revealed by the micro¬scope. Further, frequent references are introduced to important papers on the different subjects discussed, in order to direct the student's attention to the original literature. The Descriptive part of the volume is essentially an abridgment of the Sixth Edition of Dana's System of Mineralogy, prepared by the author (1892). To this work (and future Appendices) the student is, therefore, referred for fuller descriptions of the crystallographic and optical properties of species, for analyses, lists of localities, etc.; also for the authorities for data here quoted. In certain directions, however, the work has been expanded when the interests

Jan 1, 1922

By C. F. Jackson

THE work of, the Mining Methods Committee is now well under way. Following discussions previous to and during the February meeting, an Outline for Papers on Mining Methods was prepared, and over a thousand copies have now been distributed to committee men, to section secretaries and to members who have indicated any interest in the subject. The objective of the committee is to prepare a symposium on mining methods which will be of real practical value to the operator and engineer in the solution of every-day mining problems. It is planned to cover the entire field of mining in such a way that the different branches of mining, such as coal and ore (iron, copper, lead, zinc and precious metal) can benefit from the experience of the others at points where they have problems in common.. It is realized fully that each of these branches of mining possesses its own peculiar problems, but at the same time, there are prob-lems in connection with each, where the experience in others should be of value. The committee proposes to proceed along the following lines: 1. To present a general classification of mining methods, showing their inter-relationship, and at the same time .provide a common language for the discussion of mining methods and a nomenclature that will have the same meaning wherever used. A com-plete set of illustrations will accompany the classi-fication to make clear the terminology adopted and to show graphically the inter-relationship of methods. 2. To show the relationship between the physical characteristic of the deposit, the economic consider-ations and the. mining method., It is not proposed to treat this subject as a mere academic problem, but to secure reports from every mining company of impor-tance in this country, which will show what methods or modifications and combinations of methods have actually been applied and the physical conditions and economic considerations which have led to the adoption of these methods in each case. The Mining Methods Committee has drawn up an Outline for Papers on Mining Methods to be distributed among mining engineers and operators, giving in detail the information desired. This outline is the result of several months of careful thought and is a composite of the suggestions of many engineers and mining company officials from all parts of the United States.

Jan 7, 1922

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

By G. C. Gester

Oil has been produced in Persia and India for many years, but it was not until 1932 that Arabia entered the arena as a potential oil-producing area. In 1930 the Standard Oil Co. of California acquired a concession covering the rights of exploration and exploitation for oil in the Bahrein Islands and in June, 1932, the first commercial production was discovered by the bringing in of a well known as Jebel Dukhan No. 1 on the Island of Bahrein. Since then the Standard Oil Co. of California through its wholly owned subsidiary, The Bahrein Petroleum Co. Ltd., has been carrying on a systematic survey and development program of its concession in the Bahrein Islands. This group of islands, of which Bahrein is the largest, is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Although geographically a part of Arabia, the islands are not a part of the Kingdom of Saudi Arabia. Their government is essentially independent but certain special rights have been granted to Great Britain through a series of treaties. The Island of Bahrein is 32 miles long by 9 1/2 miles wide and covers an area of 215 square miles. Approximately three-fourths of the island is occupied by a relatively low, broad, elliptically shaped dissected hill, the central part of which is slightly depressed with inward-facing cliffs but culminating in the Jebel Dukhan (Hill of Smoke), which rises to an elevation of 443 ft. above sea level. The topography of the island is a good index of its geologic structure. Structurally the island is an elongated dome or quaquaversal fold composed of rocks of Eocene age. The major axis of the fold strikes N.5W. All of the topographic high portion of the island is a part of the structural uplift. The crest of the fold is broad and flat with the dips increasing on the flanks. How far tilted strata may continue beyond the line where the Eocene beds are covered by recent sands and detrital material is not known. Superimposed on the general structure are a few small irregularities in the form of minor folding and faulting. There is, however, no evidence of any major faults. The largest of the irregularities lies to the south of Jebel Dukhan and has the appearance of a sink

Jan 1, 1934

By d&apos, C. Antonio, S. H. Reichman

In the course of our studies of the annealing behavior of vapor-deposited silver films we have determined the electrical resistivity as a function of annealing temperature for films in the thickness range of 630 to 3240A. Fig. 1 shows the resistivity of the silver films vs film thickness in as-deposited and annealed conditions. The films were prepared by depositing 99.999 pct pure silver from molybdenum boats onto Vycor substrates. Deposition was conducted at a residual pressure of 5 x 10"6 Torr at rates of 20 to 408, sec-'. Thicknesses were determined using a multiple-beam interferometer. During annealing, resistance was measured using the four-probe method. Measurements were made every 5°C during two consecutive anneals to 300°C under a continuous vacuum of 2 x X6 Torr. The heating and cooling rates during annealing were approximately l° and 2°C min-', respectively. Typical resistivity vs temperature curves are shown in Figs. 2 through 4. There is an inflection point evident at 120°C on Fig. 2, the first anneal of a 3240A film. This inflection point was found on all films above approximately 1!00A on both first and second anneals. Below 1400A the inflection occurred at approximately 180°C. Figs; 3 and 4 show the first and second anneals of a 1370A film. The inflection point occurs at 180°C on the first anneal and approximately 120°C on the second. Our interpretation of this phenomenon is based on oxygen liberation from the film surface. It is well-documented that the presence of oxygen on silver surfaces causes a reversible increase in resistivity.1"3 The liberation of this oxygen, for example during vacuum annealing, would therefore cause a decrease in resistivity as observed on Figs. 2, 3, and 4 as a change in slope. This is accounted for by the decomposition of Ag20 on the film surface. The free energy of AgzO becomes positive between 125" and 225°C.4 The thickness dependence of the inflection points can be explained as an orientation effect. The films used in this study were preferentially oriented with their (111) planes parallel to the Substrate.''~ In addition it has been sten that the thinner films, below approximately 1500A, possess a decided "hill and valley"

Jan 1, 1969

Discussion of the paper of HOWLAND BANCROFT, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1767 to 1769. THEODORE SIMONS, Butte, Mont. (communication to the Secretary*). -While preparing maps and models for use in mining litigations the writer was frequently confronted with the problem referred to in Mr. Bancroft's paper. His chart gives the apparent angle of dip with which a vein should be plotted on a vertical section not at right angles to the strike of the vein. For a quick determination of this apparent angle the writer has used an exceedingly simple graphical method, which he believes may prove helpful to engineers engaged in practical work. It is submitted, not as a criticism of Mr. Bancroft's paper, but as a means of solving the same problem when no chart is available and when calculations would consume too much time. The writer's method requires merely a few lines marked off on a piece of tracing cloth, as shown in Fig. 1: Draw line be on any convenient scale. At b erect a perpendicular, ba. By means of a protractor cut off on ba a number of angles within the probable range of variation of dip, so that a line connecting a and c, for instance, forms an angle of 60° with be, etc. With b as a center and be as a radius, draw a circle through c. This completes the tool for solving the problem. Fig. 2 represents the line of strike of the vein and db the trace of the vertical plane on which the vein is to be plotted with the apparent angle of dip. A° is the angle which this plane makes with the strike. Fig. 3 shows the application of the method: Place line cb of tracing over line db of Fig. 2 and move fore and back until line of strike becomes tangent to the circle. Connect d with the point (a) that marks the true angle of dip as found by measurement in the mine (60° in the case illustrated). The angle adb is the apparent angle of dip (C°) to be used in the vertical section. Proof.-As stated in Mr. Bancroft's paper, the apparent angle of dip is: tan C° = sin A° tan B° (1)

Jan 12, 1914

By R. W. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the SO2 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the entire operating and capital cost of the better hydrometallurgical processes. There is considerable incentive to reduce the cost and energy required for producing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper.1 Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO: and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 A series of steps, including sulfite reduction, constituting a crude flowsheet was suggested by Parker in 1976.3 The present paper describes a detailed complete. sulfite process flowsheet based on materials and energy balances, discusses the chemistry, and discusses further work that is required to develop this process. Process materials, utilities costs, and energy requirements are projected to be unusually low because of the utilization of sulfur from the concentrate. Process Description The sulfite reduction process requires a copper concentrate containing approximately as much sulfur on a weight basis as copper. For those few concentrates that are deficient in sulfur, additional sulfur can generally be obtained by allowing more pyrite to float in the concentration process. The process steps, shown in [Fig. 1], are (1) a fluid bed roast of the concentrate, (2) a leach of the roaster calcine using recycled barren liquor from the reduction autoclave, (3) scrubbing of the SO2 gas with ammonium sulfite liquor to produce ammonium bisulfite, (4) reduction and precipitation of copper in an autoclave by combining part of the SO2 scrubber effluent (SO5

Jan 1, 1980

By E. G. Dean

A method of top slicing has been devised at the Miami Copper Co.'s mine at Miami, Aria., which differs radically in some ways from the customary methods of top slicing. The area of that section of the orebody in which top slicing is used is about 800 ft. square. The ore, while for the most part soft, is, nevertheless, considerably harder than the capping. The latter is siliceous, seldom containing any clay or other binding material, and breaks into fine particles so that it runs like sand if given the opportunity. Because of these facts, and because the ore is above the average grade of the mine ore, it has been mined by top slicing. Haulage levels are opened up 150 ft. apart, vertically, with two sub-levels between at 50-ft. intervals, to facilitate the putting up of ore chutes. These sublevels are used during slicing for distributing air in the ventilation system. On the haulage level the drifts are spaced on 50-ft. centers, and raises along these drifts are also spaced on 50-ft. centers, except the incline raises as hereafter noted. The raises are cribbed where necessary. Where the wear will be excessive, 1/4-in. iron plates are spiked to the top of every third set of cribbing, for its protection. When top slicing was first used, an attempt was made to carry a slicing face from fifty to several hundred feet long. Timber and other supplies were brought in through long drifts from an auxiliary shaft. Great difficulty was experienced in keeping these drifts open, the side pressure breaking the posts and the top weight breaking both caps and posts. Furthermore, the men could not work efficiently while these drifts were being repaired. The slicing faces advanced irregularly, due to varying conditions, and in many ways the results were not all that could be desired. It was then decided to divide the slicing area into blocks 200 ft. square and this was later changed to 250 ft. square. At the center of each block a two-compartment raise is put up as a supply raise, the compartments being 2 ft. 6 in. and 4 ft. by 4 ft. 4 in., the smaller being used as a manway. Station sets of 12 by 12 timber with

Jan 1, 1917

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

By Edward Hart

Having occasion several years since to make ferrous sulphide, I attempted to do so by fusing a mixture of coal-brasses (FeS2) and dried ferrous sulphate. A very nice-looking sulphide was obtained; but on attempting to use it, I found that it was insoluble in dilute hydrochloric and sulphuric acids. The subject was laid aside at the time, but has since been taken up; and some curious results have been obtained, which I believe are new. I have made the material by all of the following methods and the product seems to be pretty much the same, however obtained : (a) FeS2 heated to fusion. (b) FeS2, and FeSO4 heated to fusion. (c) FeS2, and Fe2O3 heated to fusion. (d) FeS2, and FeCO3, heated to fusion. (e) FeSO4, and S heated to fusion. (f) Fe2O3 and S heated to fusion. Obtained in this way the mass after cooling breaks easily and is very nearly black in color. On the upper surface of the fused cake the color is generally reddish or brownish black. When this is treated with dilute sulphuric or hydrochloric acid, it refuses to dissolve; but if touched with the point of a file or any piece of wrought-iron, solution of the sulphide takes place with the evolution of sulphuretted hydrogen. If the iron is removed the evolution of gas ceases, and only begins again when the iron is again brought into contact with the fused sulphide. The same thing happens if the iron is connected with the sulphide by means of a platinum wire. But in all the samples of fused sulphide I have obtained, if the iron is allowed to remain in contact with the sulphide for a certain time (which varies with different samples of the fused sulphide) and is then removed, solution of the sulphide continues. Zinc, tin, and magnesium have the same effect as iron. In hydrochloric acid aluminium acts more rapidly even than iron. In sulphuric acid it has little if any effect. Copper in HCl, when brought in contact with the fused sulphide, dissolves quietly without evolution of gas. The solution of copper chloride formed becomes,as it flows down over the sulphide, converted into copper sulphide.

Jan 1, 1887

By John Birkinbine

A RETROSPECT of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are iron¬masters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried ; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

Jan 1, 1876

By Samuel Taylor

IT is customary for the president of an engineering society, in his annual address, to describe either some engineering problem with which he has beer connected or to review the work of the society during his administration. My first thought, this being the sesquicentennial year of our nation, was to review the advance in coal mining for the past fifty years, during which period I have been more or less intimately con-nected with the bituminous coal industry, and have personally witnessed most of the great changes which have occurred in methods and machinery used in the production of coal, but preparation of the requisite address would take more time than could be spared to prepare it, and its presentation would consume so much time that it .would not be suitable. The new arrangement providing for giving the presi-dent's address at the business meeting makes it more .appropriate to review the work of the Institute during the past year, together with some suggestions which appeal to me as being of advantage to the future wel-fare of the Institute, which I will try to do briefly. The work of the business office has been reviewed in the Secretary's report and it will not be necessary for me to dwell on it. Suffice it to say, it seems to be going along very well. Additional work could be done which would be to the advantage of the Institute, if we had the money with which to defray the necessary ex-pense incident to it, but I will refer to this again later. I would be derelict if I did not refer to the splendid work of the Secretary and the Assistant Secretary. Keeping in touch with all the sections, which number now about 26, and affiliated student societies which number 40, besides special committees, and represent-ing the Institute on various boards, provides work enough to occupy the Secretary's time almost exclu-sively. In addition to this the Secretary and the As-sistant Secretary have the work of editing and publishing the TRANSACTIONS of the Institute; the issuing of the magazine, MINING AND METALLURGY, in the splendid manner in which it goes out to the mem-bership is no light task and I think they should receive the commendation of the membership for this work.

Jan 3, 1927

By Stirling Huntley, R. H. Johnson

Pennsylvania will be remembered, as long as oil is produced, as the cradle of the industry of petroleum in North America. It was on Oil Creek, near Titusville, Venango Co., that Col. Edwin L. Drake, superintendent for the Seneca Oil Co., brought in the first commercial oil well on Aug. 28, 1859. Great difficulty was experienced in getting the well down to the producing depth of 69 ft. (21 m.) with the spring-pole system then in vogue for punching shallow water wells, so the novel expedient of driving an iron tube through the surface clays and quicksand was finally resorted to. The well had an initial yield of 25 bbl. a day on the pump, but soon went off, though 2000 bbl. were produced by the end of the year. With the Drake well a success, a young industry sprang into being, the rapid growth of which has been second to none in the country and the value of whose product is only surpassed by that of coal. For years the only producing territory, the Pennsylvania-New York field attained its greatest production in 1891, when the bringing in of the McDonald pool, between Pittsburgh and the West Virginia line, gave a total of over 33,000,000 bbl. At present the field, combined with West Virginia and southeast Ohio, gives 25,000,000 barrels. Geology and Stratigraphy In general, the Appalachian field is a huge geosyncline, the axis of which runs roughly northeast-seuthwest, from north of the New York state line south through Brookeville, Kittanning, Pittsburgh, Washington, through the southwest corner of the state of Pennsylvania into West Virginia. Minor folding has accompanied or followed the dominant fold of the field, and it is from these structures near the Pennsylvania-West Virginia line and their influence on the accumulation of oil and gas that I. C. White, state geologist of West Virginia, obtained his evidence for anticlinal guidance of prospecting. Many horizons in the geologic column of the field serve as reservoirs, and there arc several pools that have wells producing side by side from different and widely vertically separated strata. The strata show a promising succession of porous sand and conglomerate horizons alternating with numerous gray and dark brown 01. black shales, admittedly

Jan 1, 1921

By John Birkinbine

A retrospect of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are ironmasters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

By Ernest Gayford

This is a nontechnical paper on flotation, subdivided under three general headings: (I) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? Definition T. A. Rickard defines flotation' as "the act or state of floating," from the French flottaison, water-line and flotter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer,2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small particles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the films of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart3 defines flotation as follows: Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By Ernest Gayford

THIS is a nontechnical paper on flotation, subdivided under three general headings: (1) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? . DEFINITION T. A. Rickard defines flotation1 as "the act or state of floating," from the French flottaison, water-line and fitter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer 2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small parti- cles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the 6lms of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart defines flotation as follows : Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928