Search Documents

By D. M. Kehn

A method has been devloped for chromatographic analysis Of the vapor and liquid phases Of a a system containing methane to components having 20 or more carbon atoms. The method uses a windowed equilibrium cell in which volumetric phase behavior of the system can be observed accurately and from which small samples of gas or liquid can be withdrawn for analysis. Analyses are made using two chromatographs, one for the lighter and one for the heavier components in a sample. Combination of the two analyses yields a detailed analysis of the gas or liquid sample. The complexity of the condensate heavy ends is evident from the chromatograms of these fractions, and the predominance of the paraffin hydrocarborn serves as a useful marker in interpreting the chromatograms. The K-values obtained in this analytical method are presented for a high-pressure condensate system and predict closely the observed volumetric behavior of the system. INTRODUCTION Quantitative analysis of hydrocarbons from natural gas reservoirs is necessary for several reasons—to calculate the amount of sales gas produced, to calculate the amount of natural gasoline produced, to plan a liquid recovery system, or to calculate the potential economic value of a reservoir produced under one or more of several different conditions. Analysis of natural gas fluids produced to the surface consists of identifying and computing the mol fraction of each component of the mixture. Although methane is the predominant component, varying amounts of ethane, propane, butane, pentanes and heavier components are also present. Materials containing up to 30 carbon atoms occur in amounts which decrease with increasing molecular weight. However, the quantities of components in the 20 to 30 carbon atom range are usually so small that their importance is negligible, and they are undetect-able in natural gas by ordinary analytical methods. All the components up to those having 20 carbon atoms may sigsficantly affect phase behavior, however. Commonly, only the methane-through-pentane fraction is analyzed quantitatively for each component, while components heavier than Pentane are lumped and repored as "hexane- plus". Expensive, tedious techniques are required for analysis of this fraction. Consequently the detailed analyses needed for prediction of reservoir behavior are usually undertaken only when major gas fields are being developed. The need for complete analyses of condensate systems is apparent when it is recalled that most gas fields are produced by pressure depletion. As the pressure declines, some of the heavier hydrocarbons are lost as liquids which are in the reservoir. In many instances the amount of liquid in equilibrium with the gas phase at high pressure constitutes only 1 or 2 mol per cent of the total system. Flash calculations generally must predict the actual amount of liquid with an accuracy of a few per cent in order to be useful. This retrograde condensation has been understood for years, but accurate correlation methods to permit quantitative prediction of phase behavior in the retrograde region are not presently available. The increasing importance of natural gas has made accurate prediction of phase behavior and composition of produced natural gas streams an economic necessity. The work reported here was undertaken to provide a rapid, economical method for obtaining the vapor-liquid equilibrium information needed to predict accurately the composition of the fluids produced from a gas reservoir throughout its life. TO develop this method, a pressure cell equipped with windows was designed and built for observing the volumes of liquid and gas present at reservoir pressures and temperatures. Use was made of established chromatographic methods for rapid and detailed analysis of both phases. This paper describes the equipment and techniques developed for obtaining vapor-liquid equilibrium data, presents the results of analyses of a condensate system, and indicates the usefulness of these data in predicting hydrocarbon phase behavior. DESCRIPTION OF EQUIPMENT USED The equipment used in obtaining the required information on phase behavior and the complete analysis of hydrocarbon mixtures through C, will be described first, followed by a discussion of the operation of the equipment. It will be helpful, however, to consider first a brief outline of the technique used. A sample of separator gas and liquid is charged to the windowed cell (see Figs. 1 and 2) where volumetric equilibrium phase behavior at reservoir pressures and temperatures can be determined. Then samples of the coexisting phases are withdrawn. The methane-through-pentane fraction is analyzed with a chromatograph equipped with a hot-wire detector, and the pentane-plus fraction is analyzed with a second chromatograph equipped

Jan 1, 1965

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By D. Weinstein

The high temperature mechanical properties of stainless steels after fast neutron irradiation are discussed in the light of effects caused by lattice dattmage and effects caused by helium generated from n,a transmutations. Embrittlement at high temperatures is due to helium accumulation at grain boundaries and to cavity formation and proPagation along grain boundaries. Following from the embrittlement mechanism, it is suggested that when deformation occurs by mechanisms associated with super plasticity, helium ac-curnulation at boundaries should be attenuated and cavities, if formed, should be nonpropagating. As the mean free Path between interphase boundaries of a two-phase Fe-Cr-Ni alloy was decreased, the degree of superplastic deforrnation at 870°C increased, as vneaszired by total elongation and by the expottent m = a log &apos;a/a log &apos;i. This alloy and type 304 stainless steel were cyclotron irradiated in an a-particle beam to a helium concentration of -1 x 10 atom He per atom. The stainless steel specimen was embrittled, but the ductility of irradiated two-phase Fe-Cr-Ni alloys correlated with the values of. m during &apos;defor-malion. The .finest grained, helium-injected specimens that deforrned with highest m values exhibited the largest elongations to ,fracture. These results could be correlated with metallographic observations of cavity behavior: the propensity for intergranular propagation was lessened as the m value increased. It is concluded that superplastic deformation is ef-fectizle in attenuating helium embrittlement at elevated temperatures. One of the principal problems associated with development of fast breeder reactors is application of alloys such that suitable fuel cladding results. Stainless steels and other Fe-Cr-Ni alloys, because of highly acceptable nuclear characteristics, represent the primary materials for this component, and an exhaustive research and development effort is being conducted. The main deficiency of these materials has been a severe loss of ductility at high temperatures after fast neutron irradiation. An extensive body of mechanical property data and microstructural observations has provided an adequate phenomenological description of embrittlement; in conjunction with transmission electron microscopy studies, a reasonably acceptable embrittlement mechanism has been obtained. Following from this mechanism, it is suggested in the present work that ductility would be enhanced if deformation could occur by mechanisms associated with the phenomenon of superplasticity. Experiments to test this hypothesis have been conducted, and the results are presented and discussed in this paper. IRRADIATION EMBRITTLEMENT AT HIGH TEMPERATURE Austenitic stainless steels have been irradiated to accumulated fast neutron fluences of 1020 to 1022 nvt at temperatures between 60" and 600°C. Specimens that have been exposed to these conditions and subsequently tensile tested at temperatures between 600" and about 900°C exhibit approximately 5 pct total elongation to fracture.&apos;-3 For unirradiated specimens receiving a nearly identical thermal exposure, total elongation at these test temperatures is about 45 pct. Examination of irradiated specimens has shown that fracture propagation is entirely intergranular. These phenomenological aspects of irradiation embrittle-ment at elevated temperatures are well known and are not generally disputed. Although the explanation of this phenomenon has been controversial, a mechanism for ernbrittlement has emerged that accounts reasonably well for the observed mechanical behavior. The controversy resulted primarily from an indeterminate role of neutron-in-duced lattice damage, if any, and a presumed, but experimentally unverified, contribution to embrittle-ment from helium generated by n,a transmutations. Recently, Holmes and coworkers4 have conducted experiments that separate these effects, and the results are instructive in formulation of the ernbrittlement mechanism. Holmes el al.4 irradiated type 304 stainless steel in EBR-I1 to a fluence of 1.4 x 1022 nvt (E > 0.18 mev); the irradiation temperature was 538" * 48°C or, in terms of absolute melting point, 0.49 * 0.03 T,. After irradiation, tensile tests were conducted at temperatures of 21" to 870.C, the specimens first being annealed for 30 min at each test temperature. In addition, thin sections of irradiated specimens were annealed for 1 hr at identical temperatures, electro and examined by transmission electron microscopy. Thus, for a given temperature, it was possible to correlate mechanical properties with the defect structure. At room temperature, the yield stress of irradiated specimens was a factor of 2.5 higher than unirradi-ated specimens exposed to an equivalent thermal history. Electron microscopic examination of the irradiated specimen revealed a high density of lattice damage in the form of Frank sessile dislocation loops and polyhedral voids. Holmes et al.4 concluded that the presence of this defect substructure caused the increase in yield stress and that after irradiation in a fast neutron flux at 0.49 Tm, substantial lattice dam-age persists. Annealing at progressively higher tem-

Jan 1, 1970

By J. P. Nielsen, H. Margolin, E. Ence

The Ti-Ni phase diagram has been investigated up to 68 pct Ni with iodide titanium base alloys by metallographic, X-ray, and melting point methods, and from 68 to 90 pct Ni by examination of as-cast structures of sponge titanium base alloys. NVESTIGATION of the nickel-rich portion of the I Ti-Ni phase diagram was first reported by Vogel and Wallbaum in 1938.&apos; This work was subsequently extended to lower nickel contents by Wallbaum&apos; who indicated the possibility of a eutectic reaction for nickel contents below 38 pct. Long et al.3 studied the titanium-rich portion of the phase diagram and found eutectic and eutectoid reactions below 38 pct Ni. However, the temperature of the eutectic indicated by Long et al. was considerably lower than that suggested by Wallbaum. Long and his coworkers synthesized their alloys by powder metallurgical techniques and encountered oxygen and/or nitrogen contamination. Thus the diagram which was obtained did not represent binary alloying conditions. However from these results the features of the binary diagram were predicted. At Battelle Memorial Institute4 the Ti-Ni diagram was investigated up to approximately 11.5 pct Ni with sponge titanium alloys. The range of temperatures used was not sufficient to define the eutectoid temperature or composition. The data of Wallbaum2 and Long et al.8 were of particular interest for the present study, and although the work was originally concerned with the region below 40 pct Ni, the investigation was extended to higher nickel contents in an attempt to resolve the differences between these workers. Experimental Procedure Preliminary work on the Ti-Ni system was carried out with duPont Process A sponge titanium alloys to reduce the amount of subsequent work to be done with iodide titanium base alloys. The sponge titanium used contained 99.71 to 99.77 pct Ti, 0.1 pct Fe and 0.005 to 0.009 pct Ni. The iodide titanium obtained from the New Jersey Zinc Co. contained 99.9 to 99.95 pct Ti. Nickel used with sponge titanium was 98.9 pct pure. The high-purity nickel alloyed with iodide titanium was cobalt-free with approximately 0.05 pct C and was obtained through the courtesy of the International Nickel Co. The 15 g sponge titanium charges for melting were prepared by compacting in a die or by placing the weighed portions of nickel and titanium directly into the furnace. Iodide titanium charges were made by drilling holes in the as-received rod and inserting the nickel or by wrapping the nickel in sheet. Sponge titanium alloys containing from 0.2 to 90 pct Ni and iodide titanium alloys containing 0.2 to 68 pct Ni were prepared by these methods. In addition to these alloys several 1/2 1b sponge titanium alloys were supplied by the Allegheny Ludlum Co. The charges were melted in an arc furnace under an argon atmosphere. The procedures used were similar to those reported in the literature5,&apos; and the furnace has been described.&apos; Except for iodide titanium alloys with 40 to 68 pct Ni (see section on copper contamination), each alloy was melted for 1 min, then either turned over or broken before re-melting for an additional minute. Currents of 200 to 400 amp were used depending on the melting point of the alloy. Prior to heat treatment, alloys containing less than 14.5 pct Ni were hot-forged at 750°C. With the exception of alloys in the homogeneity range of the compound TiNi, alloys of higher nickel contents could not be hot-forged. Heat treatment of iodide titanium base alloys was carried out in argon-filled quartz capsules which were broken under water at the conclusion of heat treatment to quench the specimens. Temperatures were controlled to ±5oC and annealing times up to 48 hr were used. For melting point determination, specimens were placed in carbon crucibles which were in turn en-capsuled in argon-filled quartz capsules. The start of melting was determined by rounding of corners and by metallographic examination. Complete melting was considered to have occurred at that temperature at which the specimen assumed the shape of the crucible. Specimens were prepared for metallographic examination by mechanical polishing or by an electrolytic procedure." For alloys containing up to 80 pct Ni Remington A etch7 50 pct glycerine, 25 pct HNO,, 25 8 HF) was used. For higher nickel alloys aqua regia and Carapella&apos;s etch (5 g FeCl,, 2 ml HNO,, and 99 ml methyl alcohol) were employed. Specimens to be exposed for powder patterns were prepared by filing, by breaking specimens in a

Jan 1, 1954

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe&apos;s formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade&apos;s exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson&apos; in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of&apos; the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft &apos;-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,&apos; no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By L. H. Robinson

Triaxial compression tests have been performed to determine the strength characteristics of limestone, sand-stone and shale rocks subjected to controlled stress conditions. This control tuns exercised by varying the liquid pressures within and around a plastic-encased rock specimen. The pressure in the pores of the rock was varied throughout the range from atmospheric to 15,000 psig; the external pressure was changed over the same range with various positive pressure differences between is and the intertnal pressure. The data show that the rock strength increased and the mode of failure changed as the pressuire. surrounding the rock became greater than the pressure in the pores of the rock. These observations and the resu1ts of microbit drilling experiments indicate that the increased rock strength under pressure may bc an important effect in reducing drilling rare, but that other factors are probably of even greater importance. INTRODUCTION A large part of the research conductcd to reducc thc cost of drilling is directed toward improving present drilling technology and dcveloping new drilling methods. In spite of the fact that drilling is essentiaIly the act of making rocks fail, many details of the mechanism of failure are not known. It seems probable, therefore, that continuing studies of the fundamentals of rock failure can lay a foundation for future improvements in drilling technology. One of the factors which affects rock failure is the stress applied to the rock. This effect has been known for many years.&apos;.&apos;.; As an example, stress studics have been published by engineers&apos; concerned with the strength characteristics of concrete in large dams. More recently, a number of investigators4-12 have explored the effects of stress on the strength of geologic formations and the geologic implications of their findings. During the last few years some research&apos;" on rock strengths has also been conductcd in an attempt to gain additional insight into the factors which affeet rock drillability. In detcrmining the strength characteristics of rocks under different stress conditions, investigators have conventionally used triaxial compression equipment. wherein a jacketed rock cylinder is uniformly loaded from all directions and then compressed longitudinally. The results of this work have demonstrated that the mode of failure (brittle or malleable) is dependent upon the loading pressure, and that the strength of the rock increases as the loading pressure increases. These results clearly manifest that the stress, which is determined by the loading pressure, affects rock strength, and this implies that rocks under stress should be stronger and hence harder to drill. During the drilling of a porous rock the stress conditions are determined not only by the pressure surrounding the portion of the rock undergoing failure (confining pressure) but also by the pressure of the interstitial fluids within the rock (pore pressure). The importancc of both these pressures on the drilling rate of rocks has already been demonstrated by a number of investigators. Murray and Cunningham" found in microbit drilling expcriments that at constant pore pressures the drilling ratc decreased as the hydrostatic pressure surrounding an unjacketed, impermeable rock increased. Later Eckel" found that for jacketed Iimestone specimens the differcnce between hydrostatic (wellbore) pressure and formation (pore) pressure had an important effect on drilling rate. These observations of the effect of pressure on drilling rate emphasize that for drilling studies triaxial compression tests should be conducted under conditions of confining and pore pressure which simulate conditions underground. In the past, triaxial tests have been made under conditions which do not reproduce those underground. In particular, most of the tests on porous materials have keen made at varying confining pressures but with atmospheric pore pressures. In only one group of tests&apos; was any data on the effect of pore pressurc reported, and these few data were on materials not representiltive of those encountered in drilling earth formations. The research described herein was initiated to deter-mine the importance of both internal pore pressure and confining pressure on failure characteristics of limestone. sandstone and shales. Triaxial loading equipment was used to obtain strength data at pressures up to 15,000 psig. An additional objective of this research was to apply these results to drilling rate studies by comparing them with the previously published drilling data of Murray and Cunningham" and of Eckel12. The work reported here is but one step in determining and evaluating the fundamental mechanisms which control drilling rate. Additional research is needed to clarify other aspects of the drilling process. The better

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener&apos;s estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5&apos;9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener&apos;s result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No&apos; 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements&apos; From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No&apos; 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements&apos; From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Leo B. Bicher, Donald L. Katz

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By J. W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles. as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain. GEOLOGY The rocks of Jumbo Mountain comprise a series of folded Tertiary sediments forming a belt one half to three quarters of a mile wide, trending northwest about parallel to the strike of the beds. This belt is sandwiched between two extensive in-trusives—gabbro on the northeast and quartz dio-rite on the southwest—and has been intruded by dikes of fresh and serpentinized dunite. Shear zones follow many of the dunite-sedimentary rock contacts, and in these the nickel mineralization is concentrated. A few transverse faults offset the sediments and ultrabasics. Sedimentary Rocks: Two kinds of quartzite make up the greater part of the sedimentary section. One is dark purplish gray, very fine-grained, and thin-bedded; the other is light gray to white, medium-grained, and well-bedded. Locally the light-colored quart lites contain grit and conglomerate horizons, rich in pebbles of white chert and very fine-grained quartzite. Intercalations of dark argillites near the summit of the mountain give many of the cliffs a striking banded appearance. Dark gray to black, aphanitic, thin-bedded argillites occur throughout the entire sedimentary belt. Beds vary from a few inches to a few tens of feet thick and some, near the summit, contain numerous fossile (willow?) leaves. Only the thicker beds were mapped. The sediments are quite fresh on the northeastern side of the belt and become more metamorphosed (hornfelsed) toward the southwestern side. Brown biotite is present in the metasediments in increasing amounts as the quartz diorite is approached. Near the intrusion, porphyroblasts of plagioclase, up to 1 in. across, testify to the soaking of sedimentary rocks by solutions emanating from the quartz diorite. Most of the sediments mapped lie along the southwestern limb of an anticline, the axis of which follows the crest of the mountain and plunges at a low angle to the northwest.

Jan 1, 1961

By H. T. Clark, S. Feigenbaum

THE importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct- reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermo- chemistry of steelmaking. The problem is not merely one of making a small number of temperature measurements in the open-hearth furnace. This has been done by several methods to a degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open- hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800° to 3100°F. are encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protection of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of .brittle materials, unsuited for handling on the open-hearth floor. The lie of the equipment was short and maintenance was an important consideration. EARLIER WORK Any one of a number of physical proper- ties of liquid steel could conceivably be used as a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1946

By Herbert H. Kellogg

C. M. Decroly (University of Brussels, Belgium) — The importance of the fluorides in the process metallurgy of special metals has already been accepted and it will probably increase in the future. Free energy diagrams as such established by Professor Kellogg are therefore very useful. It is interesting to note that the absolute value of the standard free energy of formation of HF increases with temperature, whereas for almost all the other fluorides it decreases; consequently it should be theoretically possible to reduce all the fluorides of the metals which, at low temperature, have a greater affinity for fluorine than hydrogen by this last element, provided a sufficiently high temperature is used in order to have a good efficiency. However, with regard to the reduction of UFe by hydrogen, I doubt that it will be possible to obtain directly the metal at comparatively low temperatures. There are other uranium fluorides which are more stable than UF6 and it is very likely that such fluorides will be obtained first. For example, in considering the reaction: UF6gas + H2gas + UF1so1id + 2 HFgas it is found, using the thermodynamic data of Brewer et al, that ?H298 = —66 kcal and ?G°298, = —65.2 kcal. As a result, the reduction of UF6 to UF4solld should proceed spontaneously even at ordinary temperature. On the other hand, the standard free energy of formation of UF4solid at 298°K is AG°298 = -209 kcal per mol of F2. The reduction of UF4 by hydrogen will be practically difficult and, as it is known, the only practical way of reducing this compound is to use alkaline-earth metals such as calcium or magnesium. I should like to point out, further, that the fluorination of many metal oxides can be carried out very easily by using the ammonium difluoride method of preparation, which renders the use of fluoride gas unnecessary. The first compound formed is generally a double fluoride of the metal and ammonium. This compound can be decomposed by heating either in a vacuum or in an inert atmosphere, ammonium fluoride being volatilized leaving the metal fluoride in a very pure state. H. H. Kellogg (author&apos;s reply)—Professor Decroly is quite right in pointing out that the formation of lower halides of uranium may complicate the reduction of UF6 by H2. I was unable to find his reference to the free energy of formation of UF4 in the compilation of Brewer.13 however. The value of AG°298, = —209 kcal for formation of ½ UFa seems rather high, and I hope the source of this value may be made clear.

Jan 1, 1952

By Robert W. Elayer

In August 1973, Fluor Utah, Inc. was awarded a contract by the Office of Coal Research (now part of the Energy Research and Development Administration), Department of the Interior, for the examination of the unique problems of large-scale surface coal mining to supply coal conversion complexes. The project consists of two phases: (I) data base development and organization and the formulation of a mathematical computer modeling system for surface mining; and (II) computer manipulation of the data base in accordance with the model to formulate several typical preliminary mine and preparation plant designs. Phase I is scheduled for completion by the end of July 1975 and Phase II is scheduled to be complete by the end of January 1977. This paper briefly discusses the effort for only one aspect of this project-the foundation for geologic modeling developed in Phase I. The Phase I task of geologic modeling can be broken down into two subtasks: (1) identify areas containing sufficient resources of surface-minable coal to support at least one large-scale mining complex, and (2) characterize the coal deposits in these areas for computer storage and retrieval. Identification of Resource Regions The basic production design criteria for large-scale surface mining, as stated in the contract, is the production of 75,000 tpd, or more, of bituminous coal. Based on a constant total Btu delivered to the preparation plant, daily production requirements for the different coals are as follows: Bituminous Coal 75,000 tons Subbituminous Coal 99,500 tons Lignite 143,500 tons Although surface mining on this scale is presently non-existent, it is deemed that future operations, in order to meet the increased energy demands, will have to look forward to much larger scale mining complexes. These tonnage requirements are meant to be used only for the delineation of general areas suitable for large-scale surface mining, termed "Strippable Coal Resource Regions." They were determined largely from the latest complete detailed coal resource estimates of the U.S. Bureau of Mines. Nine strippable coal resource regions, containing over 100 billion tons of strippable coal resources, were identified [(see Fig. 1)]. The delineation of these regions was based entirely upon estimates of surface-minable coal resources and the production design criteria for large-scale surface mining. If surface-mined coal was combined with underground production, or if smaller production rates were specified, then other areas which were omitted here would be included in the regions. Changing the outline of the regions, however, would not add any new mining situations to be studied in Phase II. Characterization of Coal Deposits The second subtask involved the general characterization of the coal deposits contained in the strippable coal resource regions. The geological information gathered

Jan 1, 1976

* A complete magnetic picture of the Mesabi range is now available for the first time with the release of 21 additional maps based on the aeromagnetic survey of 30,000 square miles made jointly by the USGS and the Minnesota Geological Survey. A potential iron formation with a magnetic pattern remarkably like that of the Mesabi iron range lies buried beneath the glacial drift in a wide belt extending some 30 miles across the northwest corner of Itasca County in north central Minnesota. Identification of three new uranium minerals by the USGS was recently announced. The new minerals, andersonite, swartzite, and bayleyite are, respectively, hydrous uranyl carbonates of magnesium, of sodium and calcium, and of calcium and magnesium. They were first observed by Charles A. Anderson, Survey geologist, in a coating on gypsum on the 300-ft level of the Hillside mine, Yavapai County, Arizona. International Minerals and Chemical Corp. has announced a $4,000,000 expansion and development program in the Polk County phosphate fields in Florida, Plants for the manufacture of multiple superphosphate and phosphate chemicals including dicalcium p osphate for animal feed and chemical purposes, and a sulphuric acid are planned. Office building, machine shop, warehouse, and laboratory are also scheduled for erection. A new type of tramp iron detector is being used on the conveyor belt feeder at the South Agnew stripping operation. It is made of an alloy of aluminum, nickel and cobalt and does not have any electric coils. The alloy, known as Alnico, is remarkable for the permanence and intensity of the magnetism which it retains. The detector was made by Dings Magnetic Separator Co. and it is probable that Alnico will be used in magnetic separators. The American Society of Engineering Education estimates that unless the percentage of high school graduates entering engineering colleges is increased, there is a strong possibility that instead of a large surplus of engineering graduates, which has been propehsied rather widely, there will soon be fewer engineering graduates available than are needed annually by our national economy. This conclusion is reached from a survey that shows that engineering enrollments are only slightly higher than prewar whereas industrial expansion is increasing the need for engineers. * The natural resources of Korea are being investigated under ECA sponsorship. E.J. Longyear has just embarked 8 crews for that country; two drills are scheduled for base metal search while six are slated for development of coal reserves. An innovation in the development work in the iron country has been the adoption of the Drill-Mobile, jumbo-mounted drills on rubber-tired carriage, by Cleveland-Cliffs at the Mather A and B mines. The machine is being used to cut stations in the new Mathed B shaft and for driving development headings at the Mather A.

Jan 5, 1950

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947