Search Documents

By B. J. Steblay

Roof bolts are the primary means of supplemental support in coal mines and are widely used in other mines. Presently, post installation loads are measured infrequently on only about 10% of the bolts by using standard torque wrenches that limit accuracy to about ± 30%. Because mine roof bolts are long, slender, non-uniformly sized, roughly forged, placed in a difficult environment, and subject to severe bending on installation, researchers have been unable to use ultrasonic reflection techniques to measure strain. A complete measurement system has now been assembled by the US Bureau of Mines, Denver Research Center. Obstacles such as bolt preparation, transducer mounting, reliable reflection, and calibration have been dealt with. The seemingly simple concept of measuring the time of flight of an ultrasonic pulse to a reflector is actually complex due to the need to measure to 0.0025 mm (0.0001 in.) accuracy, the sensitivity of velocity to temperature, and stress, and the stability required to make measurements over several years.

Jan 1, 1986

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By J. S. Seawright

Haulage is a costly feature in the operation of an open pit mine, whether it be iron, copper, or limestone. The National Iron Co. has adapted an old underground method to the open pit inclined skip haulage to bring the ore from the pit bottom to the crusher or beneficiation plant. The Rockover skip has been placed in operation where limited areas have retarded or eliminated use of long rail or road slopes. Deep and narrow orebodies subject to rapid increase in depth that discourage use of conveyor belts and necessary crushing plants are ideal for this system. The skip haulage method was developed to combine the desirable features of conveyor, truck, and rail haulage and at the same time avoid the draw- backs. The skip was designed to follow the natural angle of repose of the pit wall and can vary from 25° to 45°. Open-pit skips now in operation show that the installation is successful and provide the

Jun 1, 1955

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By K. V. S. Sastry, M. Cross

A summary of recent progress in understanding the main factors affecting the pelletization of fine particles is presented. A scheme for categorizing the mechanisms responsible for pellet growth is out- lined and laboratory methods to both identify the important growth mechanisms and quantify the effects of the major factors influencing the rate of pelletization are described. Next laboratory and mathematical simulations of the commercial process involved in pelletizing iron ore concentrates, are presented. The operational instabilities associated with this pelletization process are described and subjected to a control theory analysis. This analysis, in conjunction with the mathematical models, is used to both explain existing control problems and assess the effectiveness of possible circuit redesigns at producing a more stable and controllable operation. Although much of the discussion is in the context of iron ore pelletizing the approach developed to analyze the agglomeration behavior of these concentrates should apply to most other fine particle systems.

Jan 1, 1980

By W. T. Hicks

The oxidation of CbO was studied by a gravimetric technique from 400° to 1200°C in oxygen. In this temperature range the oxidatiotz is characterized by an irlductive period of low oxidation rate, which becomes shorter as the temperature increases, followed by a rapid parabolic oxidation. The oxidation of CbO cannot be rate controlling in the oxidation of Cb metal in the temperature range, 800° to 1200°C. A thin optically inactive layer has been observed between the metal and Cb2O5 layer of Cb oxidized at 700°C or higher temperatures. Figs. 1(a) and 1(b) show the edge of a sample of Cb reacted to 50 pct of complete oxidation at 800°C. Fig. l(a) taken under bright field illumination shows a layer of oxide adhering to the unoxidized metal core. Fig l(b) taken under polarized light shows that this oxide layer is

Jan 1, 1962

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By William E. Ford, Edward Salisbury Dana

447. Minerals, as regards their chemical constitution, are either the uncombined elements in %native state, or definite compounds of these elements formed in accordance with chemical laws. It is the object of Chemical Mineralogy to determine the chemical composition of each species; to show the chemical relations of different species to each other where such exist; and also to explain the methods of distinguishing different minerals by chemical means. It thus embraces the most important part of Determinative Mineralogy. In order to understand the chemical constitution of minerals, some knowledge of the fundamental principles of Chemical Philosophy is required; and these are here briefly recapitulated. 448. Chemical Elements. - Chemistry recognizes about eighty sub- stances which cannot at will be decomposed, or divided into others, by any process of analysis at present known; these substances are called the chemical elements. A list of them is given in a later article (452) ; common examples are: Oxygen, nitrogen, hydrogen, chlorine, gold, silver, sodium, etc.

Jan 1, 1922

By A. S. M’Creath, E. V. d’Invilliers

The rapid development of the southern coal and iron-ore fields during the past few years, and especially in the latter half of the year 1886, and the avidity with which everything relating to the industrial situation there is read and absorbed by the professional and non-professional public, has led to the preparation of a brief paper for the Institute upon a comparison of the raw materials available on or about January 1st, 1887, at three prominent centers of consumption. While disclaiming any originality or priority in the treatment of the resources of these districts, where so much valuable and interesting work has been performed in the past by several members of the Institute, we hope that the presentation of some analyses of samples personally secured by us in the several districts selected, and prepared for a comparative study of the character of the materials actually used and to be used by the furnaces of the "New

Jan 1, 1887

By A. D. Hodges

The process to be described, whatever other merits (or demerits) it may have possessed, certainly proved a financial success under the conditions of the locality where it was introduced and where a refining process had been sought previously in vain. I have ventured to bring it to the notice of the Institute in the hope that it may prove of some interest as a solution of a practical problem, such as is often presented to the metallurgist in the remote mining regions of the West. The method was used first at the Lyon Mill at Dayton, Nevada, and has been adopted at other tailings-mills on the Cornstock. These mills treat two classes of tailings: "sand," or; material which has passed previously through the pans of the ore-mills; and " slimes," or the fine clayey material which, coming from the battery, is too light to settle in the tanks inside of the mills but is

Jan 1, 1886

By James M. Schopf

Coal petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petrographic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures.

Jun 1, 1956

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.'

Jan 1, 1964

Research and Development, once considered a luxury item only for well-heeled companies, has in the last two decades come into its own as a vital contributor to the fortunes of electronic, automotive, chemical and aerospace firms. In terms of money and talent poured into research, the mining industry is still far behind those industries. Although the U.S. Bureau of Mines, plus various mining and manufacturing firms and universities have made notable contributions to mining technology, the historical pattern of mining R&D shows a heavy reliance on the results of research in other industries. It is difficult to tell whether this pattern will change significantly in the future, but there is evidence of a growing awareness by mining officials that greater R&D efforts are going to be required not only to meet the nebulous demands of tomorrow's world but to meet the ever-present, mounting pressures being generated by "intra-metals" and "inter-materials" competition.

Jan 1, 1968

By H. F. Beeghly

UNTIL recently the only criteria by which steels were judged were their cost and their mechanical, chemical, and physical properties. The user was concerned with such properties as corrosion resistance, tensile strength, response to thermal treatment, hardness, ductility, and, to a growing extent in recent years, with behavior at high temperature. As plans were made to build power reactors, a new set of properties became important—the nuclear characteristics, which had to be considered by the designer and engineer in building his plant. The nuclear engineer developed methods for the rare and new metals and produced them in high purity, often at great expense. The pure metals then provided the raw materials for tailor-made alloys. For more common structural metals, such as steel, the nuclear industry depended on commercially available materials. Generally, the quantities required were small and specifications were rigid. It is not surprising, therefore, that difficulty was frequently encountered in procuring structural mate-

Jan 1, 1957

By Lawrence Henderson

TO increase tonnage in the early days of coal mining it was necessary only to hire more men. The job now is to increase the tons per man, but other troubles arise because this has been accomplished. With the introduction of continuous miners, newer and faster loading machines, and faster belt conveyors the safety engineer has been faced with new difficulties. Use of larger equipment created roof control problems, which were thoroughly studied by the safety engineers of various companies. With the assistance of the U. S. Bureau of Mines, safety engineers in Alabama conducted roof bolting experiments wherever they appeared to be applicable. Accident records before and after the method was adopted showed results more than justifying the efforts and funds expended. The larger mining companies responded enthusiastically to the program because roof bolting not only prevented accidents but also increased production efficiency, in many cases rep- resenting the margin between profit and loss. In Alabama today there are miles of roof supported by bolts.

Jan 8, 1957

BLOCK CAVING HAS BEEN DEVELOPED to a high degree of efficiency in the last two decades and more particularly since World War II. At the Jeffrey mine of Canadian Johns-Manville Co., in the Eastern Townships of Quebec, several innovations have increased production and decreased costs. Asbestos ore is produced at the rate of 10,000 tpd from an underground operation supplemented by a large open pit that has been mined since 1881. The orebody consists of asbestos veins in a fractured and serpentinized peridotite. Hardness and structural strength of rock vary from soft shear zones at one extreme to a small amount of hard granitic inclusions at the other. In general the ore is weak and deteriorates on exposure to air, so that it is difficult to maintain underground openings for any period of time. Permanent workings are lined with concrete and temporary ones are driven mini- mum size and supported with steel sets as required.

Jan 5, 1954

By L. L. Wyman

SINCE the observations of Heyn,1 relative to the embrittlement of copper after having been heated in hydrogen, this subject has received considerable attention from later investigators. The published works of Archbutt2 and of Bengough and Hill3 give the reasons for this embrittlement-the formation of steam by the reaction between cuprous oxide and hydrogen. From Ruder,4 Pilling,5 Moore and Beckinsdale,6 Bassett and Bradley,7 and from Smith8 can be obtained quantitative data concerning the action of hydrogen and other reducing gases on copper samples having various oxygen contents. This problem has been discussed from a practical standpoint by Fuller9 who calls attention to some of the instances of this embrittlement encountered in the manufacturing field. The examples he cites may be considered typical cases of copper embrittlement which were incident to the process of manufacture. In many cases, such difficulties are overcome by changes in the manufacturing process.

Jan 1, 1931

By Herbert Clark Hoover, Lou Henry Hoover

THE third book has explained the various and manifold varieties of veins and stringers. This fourth book will deal with mining areas and the method of delimiting them, and will then pass on to the officials who are connected with mining affairs'. Now the miner, if the vein he has uncovered is to his liking, first of all goes to the Bergmeister to request to be granted a right to mine, this official's special function and office being to adjudicate in respect of the mines. And so to the first man who has discovered the vein the Bergmeister awards the head meer, and to others the remaining meers, in the order in which each makes his application. The size of a meer is measured by fathoms, which for miners are reckoned at six feet each. The length, in fact, is that of a man's extended arms and hands measured across his chest ; but different peoples assign to it different lengths,

Jan 1, 1950

For more than 100 years, the Republic of Chile has been one of the leading copper-producing countries of the world. Between 1877 and 1880 Chile accounted for over 50 pet of total world copper production. Today it has the world's largest known reserves of copper ore and a capability of producing over 600,000 tons per year. This capacity can and will be increased as the world demand for copper grows steadily during the remaining years of this century. The Potrerillos mine of Andes Copper Mining Co., a subsidiary of The Anaconda Co., was developed in the rugged, high Cordilleras in the early 1920's, and the townsite, concentrator, leaching plants, smelter, railroad, power and port facilities were completed so that it came into full production in 1927. Since then and until the closing o f the mine in June of last year, 1,762,192 tons o f copper were produced.

Jan 4, 1960