Search Documents

By R. V. Norris

The great coal strike of 1902, which confined the work at the Short Mountain colliery of the Lykens Valley Coal Com pany almost exclusively to pumping, gave an opportunity to determine with considerable accuracy the cost of pumping the water from these very old, extensive and wet mines. This colliery, which is located in the extreme southwestern end of the anthracite coal-field, has been operated continuously since 1836, and has shipped 7,747,313 tons of coal. This and the Williamstown colliery are the only operations in Dauphin county. The workings cover about 5 miles along the North dip of the extreme westerly end of the basin, with the operating slopes near the center. They extend around the westerly spoon of the basin and back about 31/4 miles easterly on the South dip. The mines are very deep, the present workings ex tending to 711 ft. below sea-level, and about 1600 ft. below the lowest surface-opening. The coal is hoisted principally from the Short Mountain slope, which is 1550 ft. long, with 26 to 68 degrees dip, and from an inside slope, No. 4, 800 ft. long, with 52 to 72 degrees dip. The ordinary capacity of the colliery is about 1000 tons per day, and the average output for the years 1897 to 1901, in clusive, was 297,000 tons per year. The seams worked are the lowest Red Ash measures, being, respectively, Nos. I, II and III of the coal-bed series, but locally called the " Little Lykens," " Lykens," and " Whites." On the accompanying plan the Lykens seam is shown in full and the Whites in dotted lines. The pumping-plant is divided into four lifts, the pumps being located as shown in the section, Fig. 1, and the plan, Fig. 2.

Jan 1, 1904

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons- per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead, mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding, and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1952

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By F. E. Marcy

IT is not my purpose to write a lengthy article or to attempt the solotion of the problem I am presenting, but to call attention to what I believe an important issue, hoping that it may arouse in some one, or in some company, a sense of responsibility. I am referring particularly to modern up-to-date milling plants discharging tailings which under existing conditions cannot be further treated or from which a recovery cannot be made at a profit, but where a quantitative and qualitative analysis shows that a portion of these tailings might profitably bee treated, at some future time when our metallurgical knowledge has advanced, when we have cheaper power, chemicals, labor or other advantageous conditions. Early Methods In our early milling methods very little attention was given to the care of tailings. It was thought that if the mill could be located by a stream or a river where the final disposal of the tailings could be forever lost sight of, it was highly desirable. We can now see acid estimate what was lost in these rich tailings, not recoverable from the streams and the great rivers. Fortunately for many, the depositing of tailings in these streams and rivers was objected to by the farmers and finally prohibited by the State Legislatures. In looking back over our past milling methods, it seems that, the first endeavor was to make the maximum amount of money for a particular period, or year, regardless of the future, the depletion of the mine, or the conservation of the total mineral content. The dumping and sluicing of 3,000 tons per day, for a period of many years, of a copper tailing carrying

Jan 8, 1917

By D. G. Deveraux

A BRIEF SKETCH OF THE DAVE JOHNSTON MINE The Dave Johnston coal mine is located near the southwestern extremity of the Powder River Basin in central Wyoming. This mine is operated entirely for the purpose of furnishing fuel to the 750,000 Kw Dave Johnston power generation station located five miles east of Glenrock, Wyoming on the North Platte River about 24 miles east of Casper, Wyoming. Coal is delivered to the power plant by a company-owned railroad moving the coal 15 miles downgrade from the mine to the power plant. The mine first belonging to Pacific Power & Light Company has now been transferred to Northern Energy Resources Company (NERCO), a mining subsidiary of Pacific Power & Light Company. The coal beds which make up the field at the Dave Johnston Mine are locally referred to as the School and Badger seams and occur beneath gently rolling terrain in the Fort Union formation. The School seam is found approximately 180 feet beneath the Badger in the southern portion of the field and about 110 feet beneath the Badger towards the north. The coal beds dip down toward the northeast on about a four percent average inclination. The School seam has an average thickness of about 35 feet and the Badger seam about 16 feet. The climate at the Dave Johnston Mine is semi-arid, with annual precipitation varying between 10 and 12 inches with 70 percent occurring during the months of April to September, with the maximum occurring in May. A few storms occur in July and August which are usually torrential in character, often causing erosion damage to un- protected soils. Snowfall averages 50 inches a year at the mine with 12 to 15 inches of snow yielding one inch of moisture. However, snow seldom

Jan 1, 1983

By George Smith

IN the utilization of natural resources owner, operator, and consumer should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for any undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of all land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which hand owner and prospective developer are parties, must be based in theory upon a division of expected returns. Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed ; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and' the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent. or as 5 per cent. of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit.

Jan 10, 1913

By L. P. Teas

The year 1931 has been one of unusual interest in Gulf Coast petroleum development, not so much because of the number of new prospects discovered, for apparently none of any present distinction have been found, but because of the discovery of so many new oil fields and the proving of so many old prospects. During the year 10 new oil fields have been found on the Coast; five in Louisiana and five in Texas. Two suspected salt domes were proven by the drill. Production dropped from a daily average of 192,000 to 162,670 bbl., or an average of 58 bbl. for each producing well, and active operations from 189 to 119. During 1931 the Coast produced approximately 48,600,000 bbl., or 44 per cent less than in 1930, when 86,500,000 bbl. were produced. The daily return at the beginning of the year was $192,000 and at the end only $126,780, the price having dropped from $1 for A grade and a range of $0.75 to $1.22 for B grade to a price range of 70 to 86c, or an average of 78c $ per barrel at the end of 1931. The average Coastal well produced 17,400 bbl. of oil during 1931. During the year development in the old fields has continued active at Barber's Hill only, although some work is in progress at Humble, Pierce Junction, Refugio and Pettus. Clear Lake is active but the large ownerships will prevent the "boom" type of field. Production is being held fairly steady at Barber's Hill and Pierce Junction, but has declined rapidly during the year at Refugio, Humble, and to a lesser degree at Pettus. The 6000-ft. production at Barber's Hill has shown a decided drop during the year and has not measured up to expectations.

Jan 1, 1932

By E. M. Wise, R. V. Vines

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

E. A. Peretti (University of Notre Dame, Notre Dame, Ind.)—Mr. Deitz and Professor Halpern are to be congratulated on a fine piece of work which adds to our knowledge of precious metal—cyanide-solution reactions. I should like to offer the following comments: The authors state, "the rate plots were always linear, indicating a zero order reaction rate." This appears to conflict with the data of Fig. 6 which clearly show the rate to vary with the NaCN concentration. It seems to me that the rate curves are linear because of the experimental setup. The volume of solution is so large that over a three-hour period the change in NaCN concentration is very small. A rough calculation for the experiments of Table I where the initial NaCN strength was 0.0096 mol per liter show a change of NaCN concentration of about 0.0009 mol per liter at the end of three hours. In short, over the period of time that the experiment was in progress, the NaCN strength was practically constant; hence the rate of dissolution remained practically constant. Eq. 10, as written, specifies that 1 mol of H202 and 2 mol of hydroxyl ion are formed when 2 mol of silver react. Is this true? The effect of H,O2 on the rate was made in solutions having an oxygen pressure of 4.8 atm. Were any tests made in solutions containing hydrogen peroxide, but no oxygen? G. M. Willis (University of Melbourne, Melbourne, Australia)—The authors have shown that, under their experimental conditions of high O2 concentrations, the rate of solution of silver in aqueous cyanide solutions is controlled by diffusion of O2 or CN- to the metal surface. With diffusion control, it is generally not possible to obtain further information about the mechanism of a process.

Jan 1, 1955

SEVERAL distinctions can rightfully be accorded the Bagdad enterprise. For one thing, it has the most romantic name among the Porphyry Coppers and this is said with all due deference to Copper Queen and Inspiration! Bagdad was one of the richest and most magnificent cities of the glamorous world of the Arabian Nights. The record does not say who was responsible for applying the name Bagdad to the company that in 191 1 took over the property of the Arizona-Nevada Copper Company; but whoever it was must have had visions (or at least hopes) of a fabulously profitable mine. So far as I know, Bagdad is the only Porphyry whose owners, or officials, ran afoul of the law because of alleged sins of omission or commission in vending shares of the company's stock. E. B. Bronson, of New York, had been interested in Bagdad since 1909; and, during the lean period of the 1930's he had, as president of the corporation, endeavored to raise needed funds by the sale of 140,000 shares of treasury stock. Some legal questions arose as to the need for registration under the Securities and Exchange Act; but, when Mr. Bronson finally filed a registration statement, the New York office of the Securities and Exchange Commission found 155 "deficiencies" in the document. According to the judge who later heard the criminal case against Bronson, no evidence was introduced to show that he had personally benefited "to the extent of one dollar." However, it was charged that the setup was such that he was in position to profit if he had wanted to! A somewhat quixotic position, it would seem. In any event, he was convicted, on highly technical

Jan 1, 1957

By R. R. Seeber

In the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large—from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.' The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting ing-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. The hoist for No. 4 shaft is about 1,700 ft. from the power-plant, arid in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-geaerator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-km, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels

Jan 1, 1911

The Delegation of American Engineers constituted by the American Institute of Mining and Metallurgical Engineers, the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers, that visited France in December, 1918, in acceptance of the invitation extended by the Congrés General du Genie Civil consisted of the following: Representing the American Society of Civil Engineers, Major James F. Case, past president, Geo. F. Swain, vice-president, Nelson P. Lewis, treasurer, Geo. W. Tillson, past director, Geo. W. Fuller, director, A. M. Hunt. Representing the American Society of Mechanical Engineers, president, Chas. T. Main. Representing the American Institute of Electrical Engineers, past president, L. B. Stillwell. Representing the American Institute of Mining and Metallurgical Engineers past-president, E. C. Spilsbury. The delegation organized on the way over by the choice of Major James F. Case as chairman, and Geo F. Swain as secretary. On arriving at Bordeaux, the Delegation was met by Mr. S. D. Brown, associate member of the American Society of Civil Engineers; and on its arrival in Paris it was joined permanently by the following attaches: Captain P. Charton, of the French Engineers, Delegate of the Commissariat-General to accompany the Delegation and serve as liaison officer; Captain Carpenter of the American Army; and Mr. Geo. Herdt, representing the Society of Civil Engineers of France. The object of the visit was to discuss with the French engineers the large engineering, problems now facing France. Engineering problems in their restricted technical sense came up for discussion practically not at all, for the French do not need advice nor assistance along strictly scientific lines. It was in the -larger and economic aspects of engineering, to aid in building up the industries and commerce of France, that our French associates desired to learn from the experience of the American Delegation.

Jan 9, 1919

By Arthur Redfield

IN ESTIMATING the unmined petroleum reserves of Central America, it is not feasible to employ the methods that have been worked out in the oil fields of the United States. No producing wells have been brought in and no drilling sections have been made public. It is accordingly necessary to fall back on a crude "barrels per square mile" estimate. The method chosen is a comparison of the structure of the foreign field of unknown reserves with that of some supposedly analogous North American field of which the reserves have been estimated. This method makes no pretense at scientific accuracy; bit furnishes a working basis for an estimate. The areal geology of Central America is illustrated in the map prepared by Sapper and more recently in the geologic map of North America accompanying U. S. Geological Survey Professional Paper No. 71, "Index to the stratigraphy of North America." Disregarding for the present the Arrow Quaternary coastal plains and alluvial deposits of the river valleys, three chief zones may be distinguished. These are: A zone of late eruptive and effusive rocks; a zone of highly folded pre-Cambrian(?) or early Paleozoic crystalline schists and slates, considerably intruded by pre-Tertiary plutonic rocks; and a zone of more or less folded sediments, chiefly of Cretaceous or Tertiary age. The zone of late eruptive and effusive rocks of Central America begins in southeastern Chiapas, Mexico,. and extends, with increasing breadth, across southern Guatemala, across practically the whole of El Salvador, and across southern Honduras to the valley of Rio Goascorán, where the igneous zone attains a width of about 100 mi. (160 km:) East of the Goascorán Valley late eruptives and effusives play a subordinate part, being confined largely to the Departments of Valle and Choluteca. Dikes and sills of igneous rocks intrude the sedimentary formations of central and northern Honduras.

Jan 7, 1922

By Bauer. Larry G.

The vast coal reserves in the Wyoming, Montana, North and South Dakota region are sufficient to supply the total energy needs of the United States for several hundred years. Not only is there an abundance of this sub-bituminous and lignite coal available, but it is easily obtainable by strip-mining . The overburden varies from several feet to several hundred feet. This western coal has yet another asset, namely, a low sulfur content. Whereas eastern and midwestern coal has a sulfur content of 2.5%, the upper Great Plains coal contains sulfur in the 0.5% range. The importance of the sulfur content of the coal is a direct result of federal government emission standards for sulfur dioxide (SO2). Hand (1) points out that "sub-bituminous coals and lignites have a propensity for retaining this sulfur in the ash under certain conditions which is not evident in higher rank coals." This would tend to reduce further the SO2 concentration in the combustion gases of boilers. Western coal is no panacea, however, in that it is far removed from most population and industrial centers. Furthermore, the moisture content of the coal varies from 20 to 40%. This moisture is almost exclusively inherent, that is, it is chemically and physically bound to the organic matter of the coal. It is believed that the water forms a part of the coal structure perhaps as water of hydration of organic salts or organic acids, perhaps by hydrogen bonding, or perhaps by simple adsorption (2). The primary market for this coal is the electric power industry. Lesser markets will be as coke for the steel industry and possible as a raw material for coal gasification and coal liquefaction plants.

Jan 1, 1983

By Gherman Pavlovich Nikonov

Results of preliminary research on the use of small diameter water jets at high pressure for cutting rocks has demonstrated the possibility of effective cutting of anthracite. Detailed research has, therefore, been conducted at the Skotchinsky Institute of Mining to study the dynamics and structure of the small water jets and the mechanism by which they cut coal. One of the objects of this research was to obtain data for the design of a machine for cutting rock, based on the same principles as that for cutting coal. The productivity of water jet mining machines depends on the hydro- dynamic parameters of the jet. Therefore, the research on small diameter water jets was directed, initially to a study of the nature of the variation of these parameters, and to obtain a profile of dynamic pressure distribution over the section of the jet. As has been confirmed previously, the required jet pressure (to cut coal) lies in the range of 100 to 500 atmospheres. These pressures were utilized for the research. The diameter of the nozzle was changed as ~follows; 0.97; 1.24; 1.5; 2.17; 2.87; and 3.57 mm. Graphs showing dynamic pressures for each nozzle diameter and varied axial dynamic pressure were obtained over distances ranging from 2 to 70 cm from the nozzle. One of the most important hydrodynamic parameters of a jet, closely related to the dynamics of jet disturbance in air, is the magnitude of the axial dynhmic pressure. A study of the variation in this pressure with increasing distance from the nozzle led to the separation of the jet into three specific parts, which differ from each other not only in the nature of the change in dynamic pressure, but also in structural properties.

Jan 1, 1971

By S. J. Aresco, A. A. Orning

This paper presents a scheme for determination of precision for the various steps in coal sampling, sample preparation, and analysis. It also gives resulting data on 100 American coals from various coal fields covering all ranks from lignite to low-volatile bituminous. The variances of the various steps of the process are studied as a function of the coal preparation, the top size of coal as sampled, and the ash content. To understand the variables that control the overall precision of coal sampling, sample reduction and analysis, there is need for measurement of the variances due to successive steps of the process. The purpose of the present paper is to study these variances as a function of the coal preparation, the top size of the coal as sampled, and the ash content. The sampling data included are from 100 individual preparation plants from various coal fields in the United States and cover all ranks of coal from lignite to low-volatile bituminous; various types of preparation; deep, strip and auger mines; and, in many instances, mixtures from two or more coal beds or types of mines. The collection of data is continuing, but sufficient work has been done to draw some important conclusions. Since the work was done in conjunction with the Bureau of Mines sampling of coal, the time that could be spent at any one preparation plant was limited. This, in turn, limited the number of samples that could be taken for each coal. For this reason, the results from various plants were pooled in blocks. Two major blocking categories were "raw" and "washed!' The raw coals had no preparation other than crushing and/or screening. The washed coals were prepared further by some combination of wet or dry mechanical cleaning. The categories were further divided ac-

Jan 1, 1965

By M. B. Yung

Location THE Fu Chuan district lies near the eastern boundary of Kwang Si province in southern China and is connected with the coast by the West river and its branches. The Journey The first part of the journey from the coast is made very comfortably in one of the West river steamers which runs to Wuchow, the great distributing center for tile whole province. From here there are two ways of reaching the Fu Chuan district. One is to drop clown the West river for 15 miles and ascend the Yuen river for 120 miles. The other is to ascend the Fu river, which joins the West river at Wuchow, and at Ping Lok tike chairs across country. Of the two the former is the more direct and shorter but for other reasons I chose the latter. At Wuchow one must provide his own means of transportation, which may be a native boat anywhere up to 40 ft. in length, but not over 18-in. draft. The method of working these river boats against the swift current which in many places develops into rapids is interesting and worthy of note. Tracking along the bank with the tow line attached to the mast head is the most common procedure, but poling, sculling, sailing and winding up the rapids by a windlass are used as the case may require. The boatmen are the hardiest set of fellows I have ever seen often putting in 15 hr. of the most exhausting labor. The average clay's run against the current is 15 miles. On this trip one should have his own food, bedding and servants, and a guard of 10, or more soldiers is almost a necessity as certain parts of the river are infested with pirates.

Jan 9, 1914

By MCA Woolsey

(Butte. Meeting, August, 1913.). IN metallurgical circles it is known widely, but somewhat vaguely, that the ease of: reduction of metallic oxides depends largely on the way they have been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction- temperature of zinc oxides variously prepared and of several kinds.1 In said paper it was shown that the temperature it which zinc oxide evolves zinc according to the equation Zn0. +' C = Zn + CO depends upon the ;nature of:., the.' two reacting bodies. The determinations bad a range of accuracy of from 2° to. 6° C.,whereas differences were found to. amount to an extreme. of 90° C. :.86 the differences are real ones and must have, definite cause. The equation of boiling water, (H20)4 = 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. , In general, all equations. reacting e in .the liquid or the gaseous phase have-well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the temperature conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not, a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules.

Jan 7, 1913