Search Documents

By K. J. Brondyke, P. D. Hess

Lack of correlation between densities of aluminum alloy samples solidified under reduced pressure (vacuum gas test) and hydrogen content of the metal is explained on the basis of inclusions serving as nuclei for hydrogen bubble formation. As a result of these findings, the vacuum gas test is suggested as a practical tool to indicate metal cleanliness and the potential effects of hydrogen. Visual obseroation of the sample during solidification under vacuum provides more useful information than that obtained either from density meas -urements or sectioning of the solidified sample. A rapid, practical method of detecting and measuring gas in molten-aluminum alloys has been sought for many years. The development of the vacuum gas test appeared to solve this problem. However, the vacuum gas test is subject to certain limitations, and the results must be interpreted mindful of these limitations, as described herein. Since the only gas which is appreciably soluble in aluminum is hydrogen, the terms gas and hydrogen will be used interchangeably in this paper. In the early days of the aluminum industry, when techniques were not as refined as they are today, it was customary to pour small "pancakes" of alumi- num on a metal plate. These were allowed to solidify under atmospheric pressure. Excessive gas in the metal was evidenced by the appearance of small bubbles on the surface of the "pancake".' It is obvious that such a method would only show very high gas levels far above any which could be tolerated by today's standards of quality required for most applications. Various attempts were made to develop methods which would be more sensitive. Among these were measurements of density of aluminum alloys solidified under controlled conditions, radiography of cast slabs, and examination of fractures. The method which showed the greatest promise and appeared most practical was the solidification of a sample of the molten aluminum alloy under vacuum. The samples so solidified are evaluated either by observation for bubble emission during solidification, by sectioning the solidified sample and examining for porosity, or by determining the density of the solidified sample. This test is known internationally as the Straube-Pfeiffer test or the reduced-pressure solidification test, but in America it is commonly referred to as the vacuum gas test2-' and will be so designated in this paper. The determination of density appeared an attractive and convenient means of providing a numerical rating for the samples. Attempts were made in some instances to correlate densities to hydrogen contents. Unfortunately, the visible loss of gas during solidification of samples with high gas contents precluded a correlation of vacuum gas test densities with the observed gas evolution. This led to Alcoa's use of two different pressures; 50 mm of

Jan 1, 1964

Since production curtailment for other than engineering reasons is gradually disappearing, and more and more wells are now producing at capacity and showing declining production rates, it was considered timely to present a brief review of the development of decline-curve analysis during the past three or four decades. Several of the commoner types of decline curves were discussed in detail and the mathematical relationships between production rate, time, cumulative production and decline percentage for each case were studied. The well-known loss-ratio method was found to be an extremely valuable tool for statistical analysis and extrapolation of various types of curves. A tentative classification of decline curves, based on their loss ratios, was suggested. Some new graphical methods were introduced to facilitate estimation of the future life and the future production of producing properties where curves are plotted on semilogarithmic paper. To facilitate graphical extrapolation of hyperbolic-type decline curves, a series of decline charts was proposed, which will make straight-line extrapolation of both rate-time and rate-cumulative curves possible. Introduction During the period of severe production curtailment, which is now behind us, production-decline curves lost most of their usefulness and popularity in prorated areas because the production rates of all wells, except those in the stripper class, were constant or almost constant. While production-decline curves were thus losing in importance for estimating reserves, an increasing reservoir consciousness and a better understanding of reservoir performance developed among petroleum engineers. This fact, together with intelligent interpretation and use of electric logs, core-analysis data, bottom-hole pressure behavior and physical characteristics of reservoir fluids, eliminated a considerable part of the guesswork in previous volumetric methods and put reserve estimates, based on this method, on a sound scientific basis' At the same time, a number of ingenious substitutes were developed for the regular production-decline curve, which made it possible to obtain an independent check on volumetric estimates in appraisal work, even though the production rates were constant. with the now steadily increasing demand for oil to supply the huge requirements of this global war, proration for reasons of than prevention of underground waste is gradually disappearing. More and more wells are, or will be, producing at capacity or at their optimum rates, as determined by sound engineering practice. With this trend, the character of producing wells seems to regain, more or less, its "individuality," and the old and familiar decline curve appears to have had a comeback as a valuable tool in the hands of the petroleum engineer. It may be timely, therefore, to retrace the development of decline-curve analysis in the past by presenting a brief chronological review of bulletins and papers published during the past three or four decades, which have

Jan 1, 1945

By C. R. Holmgren

A large consolidated sand core was used in this investigation. Four groups of experiments including gas drives, water drives, and water drives combined with gas injection, were made. The results of the gas-drive experiments indicate that greater ultimate recovery may be obtained by higher pressure gradients. However, other considerations challenge the absolute veracity of this conclusion. Results indicate that with connate water present and a low pressure gradient during a gas drive, less gas is required to produce a given amount of oil. The saturation gradient determined during a gas drive is presented. Results of the water-drive experiments indicate that the recovery of oil is not a function of either gradient Or input rate. The presence of initial gas saturation resulted in a slightly lower final oil saturation. Injection of sufficient gas to maintain the initial gas saturation during a water drive resulted in lower final oil saturation. Introduction With the demand for petroleum products reaching an all-time record high and the location and exploitation of new reserves becoming more difficult and expensive, the oil industry must look to more thorough and efficient methods of producing the petroleum already located. Much of the previous work along these lines is exploratory and suggests a more complete investigation. For example, a great amount of laboratory work has been done on flooding sands initially saturated roo pct with oil. Since sands saturated roo pct with oil rarely, if ever, exist in nature, and because the water content is a vital factor in the ultimate recovery from the sand, laboratory investigations on cores without water must be supplemented by comparable work on cores with water present.1'2 Other investigators have done a considerable amount of laboratory work using gas and water drives.3 Krutter and Day4 have reported results of investigations using cores saturated IOO pct with oil and have concluded that " the ultimate recovery obtained, using air drive, from a completely oil-saturated core depends on the pressure gradients used. The higher the pressure gradient, the greater will be the recovery until a certain Pressure range is reached above which the reward of increased recovery is much smaller for similar increments in pressure." Yuster and Day6 conclude that less gas and less time are required to produce a given quantity of oil at high pressure gradients than at low pressure gradients; they also conclude that an increase in the viscosity of the oil requires a proportionate increase in the gas needed for recovery. Their results indicate that the gas required to produce a given quantity of oil is greatly reduced by the presence of connate water. R. C. Earlougher2 concluded, based on results of water-flooding a large number of

Jan 1, 1949

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By E. A. Gulbransen, J. W. Hickman

ONE of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film A comprehensive program has been undertaken to study these phenomena This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C Before the introduction of the electron diffraction technique, it «as necessary to use either direct chemical analyses or X-ray diffraction analyses to determine the nature of the oxide film formed on the metal or alloy Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry In special cases the information obtained may be identical, but in general both view-points are necessary Much of, the early work was carried out on the oxidation of bulk samples where thick films were obtained The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses Although much useful information has been obtained in this manner, little could be learned about the character of the protective oxides during the period when the films were actually protective Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective LITERATURE The oxidation of iron has been extensively investigated by X-ray and electron diffraction Jackson and Quarrell1 found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe304, between 515° and 900°C the stable film was FeO Above the upper change point of iron the oxide was found to be Fe304 prom 400° to 515°C , FeO, Fe304 or a mixture of the two oxides was found Recrystallization of the air-formed film below 400° and above 900°C led to the formation of Fe304 In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described

Jan 1, 1946

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By Donald J. Knight

HEAT Treatment at 1500' F of a mild steel containing 0.1 pct C, in an atmosphere which is oxidizing to both carbon and iron, results in the progressive oxidation of the metal surface with little or no change in the carbon content of the underlying metal. Further heat treatment of the scaled metal in either a neutral atmosphere or in a vacuum may or may not result in the decarburization of the metal depending upon the physical nature of the scale. It is apparent that if a continuous layer of oxide is present on the steel surface, the reaction OScale + Cmetal Cogas cannot progress since the SO formed gas would be unable to leave the oxide/metal interface. Thus, in order for the reaction to progress, the oxide must be cracked or porous. Vacuum heat treatment at 1500" F of samples with a thick continuous oxide scale showed no decarburization of the steel. However, when cracks were introduced mechanically into the scale prior to the vacuum heat treatment notable decarburization of the metal resulted and a structure as shown by Fig. 1 obtained, i.e., reduction of the crack walls to ferrite. With reference to the diagram of Fig. 2, it would appear that a mechanism of the following type takes place. Carbon atoms arriving at an oxide/metal/void interface, such as 'A', Fig. 2(a), can combine with oxygen atoms from the scale and leave the reaction site as Cogas thereby reducing the oxide to metal. On a greatly magnified scale, Fig. 2(b),this will appear as a ferrite projection along the crack wall. Carbon atoms entering this projection can react with oxygen atoms at point 'C', which is a new interface, and so on leading to a progressive growth of the ferrite along the crack wall and to the surface, Figs. 2 (c) and 1. It would appear that the only means by which thickening of the ferrite film can take place is by a diffusion of oxygen through the ferrite film to react with carbon at the newly formed ferrite/ void interface. Since the diffusion rate of carbon is reportedly much greater than that of oxygen, and since there is a low probability factor of oxygen and carbon atoms arriving simultaneously at the same site on the ferritehoid interface, there will be a tendency for more rapid lengthening than thickening of the ferrite layer, as is observed.

Jan 1, 1962

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

The Library belonging to the Institute is now administered as part of that of the United Engineering Society, the members of the Library Committee representing the Institute on the Library Board of the United Engineering Society. The main collection now consists of 115,900 books, 3680 pamphlets, 5811 maps, and 4402 searches, making a total of 129,793, a net gain of 7701 within the year. There is in addition a lending collection of 1004 volumes and one of duplicates amounting to 11,310. The library grows steadily both by gift and purchase. The cataloging is now substantially current covering 124,100 items represented by 362,145 cards. There are many rare and notable books, especially those relating to early engineering. It is truly a great treasure house of knowledge. While no severe effort is made to record all visitors the books showed 23,470 to have used the Library in 1928. In addition 5102 telephone requests for information were answered, 202 searches and 196 translations made and 34,964 photo prints furnished. The service department is maintained by small fees which cover the cost. The total amount appropriated for operating expense for the year was $46,300, of which $8,240.02 was furnished by the Institute, $5,399.45 being derived as income from the Douglas Library Fund and the remainder from current receipts. Within the year a slight change was made in the method of meeting the expenses of the Library, a flat charge of $5,000 per year being made against each of the four Founder Societies and this being supplemented by a surcharge based upon membership. The effect of this has been for the present to decrease slightly the amount that the Institute would otherwise need to pay. Placing in one collection all the books of the four societies greatly increases the number of books accessible to the members of each and opening the Library to the public is an important factor in keeping the tax exemption privilege enjoyed for the building. The Director and Staff of the Library make every effort not only to accommodate those who come in person to consult the collection but members resident elsewhere who communicate by letter or wire. The facilities of the Library are truly available to all.

Jan 1, 1929

By Joseph E. Pogue, F. G. Coqueron

Prior to 1934, published information covering expenditures by oil companies for properties, plant, and equipment and the residual investments in the various segments of the petroleum industry was not readily available. This paper presents an analysis of the funds invested by a selected group of oil companies during the years 1934 through 1942, based on an extensive study of the individual records of 30 oil companies. The sources, disposition, and characteristics of the capital employed by this group of companies are traced through a series of combined statements and appropriate charts, covering financial and operating data. The analysis of these statements not only constitutes a record useful for comparative purposes but also serves as a basis for a number of broad conclusions, as follows: 1. The petroleum industry generates the capital needed for its expansion almost entirely from its own operations and is therefore a singularly self-contained economic unit. 2. The long-term debt contained in the financial structure of the industry is small relative to the total capital employed, is less than the net working capital, and has increased but slightly during the period under review. 3. The capital expenditures of the group of 30 oil companies for 9 years amounted to 6.1 billion dollars, 58.3 per cent of which went into crude-oil producing facilities. The trend of this segment of expenditures has been downward since 1937. In 1942, expenditures for refining facilities increased sharply and for marketing facilities declined drastically. 4. The net working capital of the group increased 380 million dollars over the period, and the industry is in a favorable position of liquidity. The ratio of combined current assets to current liabilities was 3.21 at the close of the period. 5. The net income of the group displayed an upward trend for the period but with rather sharp cyclical fluctuations. 6. In 1942, Government funds entered the industry for the first time in substantial amounts and were utilized for the provision of war facilities needed for emergency use. 7. The group has paid out a relatively low percentage of net income in the form of dividends. For the period the average was 55 per cent of net income. 8. The rate of return on invested capital for the group averaged 6.4 per cent for the

Jan 1, 1944

By E. E. Barker

ALTHOUGH flotation was known to be a successful process prior to 1912, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on, a full flotation basis. EFFECT OF FLOTATION ON ORE RESERVES The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Sackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By Joseph E. Pogue, F. G. Coqueron

Prior to 1934, published information covering expenditures by oil companies for properties, plant, and equipment and the residual investments in the various segments of the petroleum industry was not readily available. This paper presents an analysis of the funds invested by a selected group of oil companies during the years 1934 through 1942, based on an extensive study of the individual records of 30 oil companies. The sources, disposition, and characteristics of the capital employed by this group of companies are traced through a series of combined statements and appropriate charts, covering financial and operating data. The analysis of these statements not only constitutes a record useful for comparative purposes but also serves as a basis for a number of broad conclusions, as follows: 1. The petroleum industry generates the capital needed for its expansion almost entirely from its own operations and is therefore a singularly self-contained economic unit. 2. The long-term debt contained in the financial structure of the industry is small relative to the total capital employed, is less than the net working capital, and has increased but slightly during the period under review. 3. The capital expenditures of the group of 30 oil companies for 9 years amounted to 6.1 billion dollars, 58.3 per cent of which went into crude-oil producing facilities. The trend of this segment of expenditures has been downward since 1937. In 1942, expenditures for refining facilities increased sharply and for marketing facilities declined drastically. 4. The net working capital of the group increased 380 million dollars over the period, and the industry is in a favorable position of liquidity. The ratio of combined current assets to current liabilities was 3.21 at the close of the period. 5. The net income of the group displayed an upward trend for the period but with rather sharp cyclical fluctuations. 6. In 1942, Government funds entered the industry for the first time in substantial amounts and were utilized for the provision of war facilities needed for emergency use. 7. The group has paid out a relatively low percentage of net income in the form of dividends. For the period the average was 55 per cent of net income. 8. The rate of return on invested capital for the group averaged 6.4 per cent for the

Jan 1, 1944