Search Documents

By Barrie T. Wells, Raghu N. Singh, Paul S. Buddery

Rockbolting and dowelling are important methods of ground control. Their effectiveness depends upon the compatibility of the support members and the geotechnical behaviour of the rock mass. Detailed geotechnical investigations are, therefore, necessary for the design of effective rockbolting systems. The study described in the paper was concerned with improving the effectiveness of ground control at Mount Isa Mine. The paper briefly reviews the design methods avail- able when choosing a rockbolting system with a view to identifying the most suitable method. Joint surveys were used for the geotechnical assessment of rock mass stability. These were interpreted with the aid of the stereographic technique of predicting the size and shape of potentially unstable blocks of rock in both the roof and side walls of excavations. The geology and ground conditions at Mount Isa are briefly described together with the current ground control techniques. The requirements for ground control have been investigated at representative sites by analysing typical modes of rock failure and using a geological predictive technique. An application of this technique to the selection of a support system in a shallow Coal Measures tunnel is also described. The paper concludes with a general discussion on the effectiveness of this method of site investigation for the appraisal of rockbolting support in mining and civil engineering excavations.

Jan 1, 1983

By E. T. Turkdogan, L. S. Darken, R. G. Olsson, H. A. Wriedt

Several aspects of the calcination of Michigan limestone were investigated: the rate of calcination of limestone spheres with diameters from 1.8 to 14 cm at temperatures from 800° to 1200°C by a thermogravimetric method; the temperature profile across limestone during calcination; the excess pressure developed in the interior of the stone during calcination; the pore surface area, pore volume, and effective gas diffusivity in burnt lime; and the microstructure of polished and fracture surfaces. It is found that, over a wide range of experimental conditions, the difference between the surface and center temperatures remains essentially unchanged during the latter half of calcination. From the rate of weight loss after about 50% calcination, the value 0.00126 cal per cm sec degree is found for the effective thermal conductivity of burnt lime. From the excess internal pressure measurements, i.e., 0.4 to 6 cm Hg at 800° to 1200°C, the permeability of burnt lime is estimated to be within the range 8 X 10-' to 5 X 10' sq cm. With increasing temperature and time of calcination, the pore structure of burnt lime coarsens as indicated by a decrease in the pore surface area, pore volume, and an increase in the average pore size. For the temperature range 600° to 835°C the ratio (effective gas diffusivity/molecular diffusivity) is about 0.18.

Jan 1, 1974

By George J. Bancroft

INTRODUCTION. IT is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Transactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,1 showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny,2 distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many of Prof. Kemp's, ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.5 This theory, dealing with, the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1913

The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement by a board composed of representatives from the four engineering Societies. The members of the Board of Award for 1917 are: A. S. C. E. A. S. M. E. George F. Swain Ambrose Swasey, Charles Warren hunt, John, A. Brashear, Charles D. Marx, Frederick R. Hutton, Clemens Herschel. John R. Freeman. A. I. M. E. A. I. E. E. Gybbon Spilsbury, C. 0. Mailloux, Charles F. Rand , Paul M. Lincoln, Christopher R. Corning, John J. Carty, Benjamin B. Thayer. Harold W. Buck. The John Fritz Medal was awarded in January, 1917, to Dr. Henry Marion Howe, for his "investigations in metallurgy, especially in the metallography of Iron and Steel." The presentation ceremonies were held in the Auditorium of the United Engineering Societies' Building, New York, on Thursday evening, May 10. Mr. Ambrose Swasey, Chairman of the John Fritz Medal Board of Award, presided, and addresses were delivered by Dr. Rossiter W. Raymond, Secretary Emeritus of the American Institute of Mining Engineers, and Dr. Ira N. Hollis, President of the American Society of Mechanical Engineers. Professor Albert Sauveur, Chairman of the Board at the time the award was made, presented the medal, and the ceremonies concluded with the response of Dr. Howe.

Jan 7, 1917

By John B. Porter

Within the last year or so, a great deal has been heard about Southern iron ; even the Eastern markets have felt the effect of the cheap Alabama ores and coals, and public attention has again been drawn to what is now getting to be an old story—the great mineral wealth of the South. The following paper is based on a report prepared several years ago for a special purpose; but since then, through association with Mr. C. B. Going in a large analytical practice and as chemists to the Queen and Crescent Railway, I have had opportunity to increase my material so greatly that the present paper is really a completely different work. I am under very great obligation to Mr. Going, without whose assistance my work would have been very incomplete, and have also been materially assisted by Mr. F. P. Dewey, of Washington, and a host of gentlemen connected with the railroads and furnaces of the South. The arrangement of this paper is not all that could be desired. Some localities of importance are very poorly represented, both in the description and the tables of analyses. This, however, was in most instances unavoidable, as the study has been done ill the intervals of professional work. I have visited almost all the localities described, and, in all cases possible, have taken my own samples, and have made careful per-

Jan 1, 1887

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By Walter English

THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By J. S. Vanick

AN extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applica-tions requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small-grain grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By J. J. Beeson

Fox the past fifty years or more, the structural features of the Cordilleran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations. of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the, result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,1. King,2 Gilbert,3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler,8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 9, 1925

By R. S. Archer

BERYLLIUM has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it, is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a pound if the metal were produced on a large scale. It seemed, therefore, that low-beryllium alloys offered the greater commercial possibilities except for very special purposes. It was partly for this reason that in the present work emphasis has been placed on beryllium alloys of low beryllium content.

Jan 1, 1928

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By Elmer R. Kaiser

Industry Adopts Research: Seventy-Ave years ago Thomas A. Edison began in a modest way and with limited funds to gather about him men of various talents to form the first industrial research laboratory. His laboratory at Menlo Park, N. J., became famous for many discoveries and inventions, but possibly the most important of all may yet be the industrial research laboratory itself. Today, private industry operates 2500 research laboratories in which 135,000 persons&apos; are directly and indirectly creating new processes and products and improving old ones, as well as developing new information to help keep the fountain of knowledge from running dry. In this change-making function, the scientific personnel comprises 41 pct; the technical personnel 26 pct; and the balance, 33 pct, nontechnical. The term "industrial research" has become so broad as to include almost everything beginning with the search for and discovery of the laws governing the properties of matter and energy to the development and testing of processes, methods, and equipment. These classes of investigation commonly merge so that no sharp boundary can be traced between them. The National Research Council therefore defines industrial research as "the endeavor to learn how to apply scientific facts to the service of mankind."&apos; Currently, expenditures for research by industry are variously estimated at between $450,000,000 to $700,000,000 a year,&apos; or about twice the expenditure for 1940. The President&apos;s Scientific Research Board" estimated that the national research and development for 1947 (excluding atomic energy) was as follows: A few companies spend as much as 5 pct of their gross receipts for research, but 1% to 2 pct is considered a good proportion by many." Shortages: Commendable as is the record of growth and accomplishment of science in industry, it is only a beginning. America and the rest of the world have merely sampled the fruits of industrial research; most industries have yet to make research the key to their future. A top research consultant, T. A. Boyd, of General Motors, states ". . . perhaps 90 per cent of all companies still have no research laboratories."Y or example, of more than 17,000 manufacturing concerns whose gross sales exceed $500,000 a year, less than 2500 have research laboratories. A still smaller proportion of the 184,230 manufacturing establishments in 161 industriese have or could afford their own research facilities. Yet, the small and mediurn-sized com,panies with less than 250 employees each, produce one half of the dollar volume of manufactured products.&apos; How are these companies to participate in and share the benefits of research? Boyd gives two reasons for the inadequate number of laboratories in industry: Many people still do not appreciate the importance of research, nor understand its tremendous potentiali-

Jan 1, 1951

By Elmer R. Kaiser

Industry Adopts Research: Seventy-Ave years ago Thomas A. Edison began in a modest way and with limited funds to gather about him men of various talents to form the first industrial research laboratory. His laboratory at Menlo Park, N. J., became famous for many discoveries and inventions, but possibly the most important of all may yet be the industrial research laboratory itself. Today, private industry operates 2500 research laboratories in which 135,000 persons&apos; are directly and indirectly creating new processes and products and improving old ones, as well as developing new information to help keep the fountain of knowledge from running dry. In this change-making function, the scientific personnel comprises 41 pct; the technical personnel 26 pct; and the balance, 33 pct, nontechnical. The term "industrial research" has become so broad as to include almost everything beginning with the search for and discovery of the laws governing the properties of matter and energy to the development and testing of processes, methods, and equipment. These classes of investigation commonly merge so that no sharp boundary can be traced between them. The National Research Council therefore defines industrial research as "the endeavor to learn how to apply scientific facts to the service of mankind."&apos; Currently, expenditures for research by industry are variously estimated at between $450,000,000 to $700,000,000 a year,&apos; or about twice the expenditure for 1940. The President&apos;s Scientific Research Board" estimated that the national research and development for 1947 (excluding atomic energy) was as follows: A few companies spend as much as 5 pct of their gross receipts for research, but 1% to 2 pct is considered a good proportion by many." Shortages: Commendable as is the record of growth and accomplishment of science in industry, it is only a beginning. America and the rest of the world have merely sampled the fruits of industrial research; most industries have yet to make research the key to their future. A top research consultant, T. A. Boyd, of General Motors, states ". . . perhaps 90 per cent of all companies still have no research laboratories."Y or example, of more than 17,000 manufacturing concerns whose gross sales exceed $500,000 a year, less than 2500 have research laboratories. A still smaller proportion of the 184,230 manufacturing establishments in 161 industriese have or could afford their own research facilities. Yet, the small and mediurn-sized com,panies with less than 250 employees each, produce one half of the dollar volume of manufactured products.&apos; How are these companies to participate in and share the benefits of research? Boyd gives two reasons for the inadequate number of laboratories in industry: Many people still do not appreciate the importance of research, nor understand its tremendous potentiali-

Jan 1, 1951

SOME days ago a visiting member from Pittsburgh who is an ardent supporter of the Institute remarked: "There are a lot of men who would be members of the Institute if it weren&apos;t so expensive. It is not so much the $15 dues as the $20 initiation fee. This makes quite a hurdle, especially for the younger fellows." A little further conversation developed the fact that the member had never learned of the changes in the By-laws regarding initiation fees and dues made by unanimous vote of the Board of Directors last November. As a great many others doubtless are unaware of these changes, the substance of two of the amendments is here repeated. They provide: (1) That the initiation fee for Junior Members (heretofore ten dollars) he abolished. (2) That the age limit for entrance as a Junior Member be increased from 27 years to 33; provided further, that the period during which the dues of a Junior Member are ten dollars shall be a maximum of six years but in no event shall extend beyond his thirty-third birthday. The Junior Member gets the identical privileges enjoyed by his seniors and he likewise assumes the same obligations with the sole exception of the financial payments. This one exception is justified by the fact that the engineers of more mature years, who are established in the profession, - are able and willing to assume a slightly greater financial burden. In effect, it is a small subsidy for the younger men; but these in turn will later enter the group of those that give instead of receive assistance. The practical result is that an engineer under 27 can obtain every privilege and benefit of membership for six years on the payment of only $10 per year without any initiation fee. A man of thirty can do the same for a period of three years. Incidentally, a candidate applying for membership (either as senior or junior) in the next few months need pay dues for the second half of 1935 only. A Junior Member -can be enrolled with an immediate outlay of only $5. The Institute does not seek-members indiscriminately merely to swell the number. These facts are not presented as a "bargain" offer in any sense. The standards for admission are high and are watched zealously. But it frankly-wants to give qualified men who can benefit from membership every encouragement to apply. Naturally, the Institute does not want lack of accurate information regarding initiation fees and -dues to be a stumbling block to any that are eligible and desirous of enrolling. Members are urged to take it upon themselves to clear up misapprehensions on this point, particularly among younger engineers.-Editorial reprinted from MINING AND METALLURGY, May, 1935.

Jan 1, 1935