Search Documents

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

By P. Barnes

Several interesting and important considerations may be based upon an analysis of the cost of producing Bessemer rails, and the facts thus set forth may be much more clearly emphasized by re ducing each item of cost to its own fractional proportion of the sum total in each branch of the manufacture. The estimate given below is not absolutely complete in minute ness of detail, but it may be fairly taken as a basis for the suggestions to be noted : Perhaps the most striking comments that can be made upon this statement are those arising from a consideration of some of the smaller items, and even the least of these quite loses its insignificance when its proportion of the whole is expressed in actual money, as for the work of a year, or even for a single day. Thus, if the item as be considered, the importance can be clearly

G. H. CLEVENGER, Colorado Springs, Colo.-Mr. Crowe's paper will be of great interest to cyanide operators, as it is a distinct new development in cyanidation. After reading the paper it occurred to me that some of us had done practically the same thing some time ago, but without design and unconsciously. I refer particularly to the operation of some of the earlier types of vacuum filter, used in connection with a dry vacuum pump and a receiver, which is somewhat similar equipment to that employed by Mr. Crowe. However, we did not appreciate the good effects we were getting from such of this solution as was precipitated, and it has remained for Mr. Crowe to bring distinctly to our attention the advantages of removing air from cyanide solutions before precipitation. Full credit is therefore due him for this very clever improvement in the cyanide process.

Jan 11, 1918

By Paul T. Allsman

Recently the U.S. Bureau of Mines completed organizational changes that, for the first time since the beginning of World War 11,. re-emphasize mining research as an important part of its responsibilities. A progress report follows on the Bureau's improved program for mining research. During World War II the Bureau's mining research lapsed in favor of short-range, more urgent activities. Since the end of the war mining has grad- ually returned to an economy where reduced costs and increased efficiency are essential to a vigorous industry, and demand for improvement through expanded research is again pre-eminent. In recognizing this situation, the Bureau is again emphasizing mining technology and has reinstituted some of its earlier mining research activities. Recent research, however, follows a more scientific approach in solving mining problems because new technology, particularly new instrumentation, has developed rapidly during the past decade.

Jan 7, 1960

At the annual meeting of the American Society of Mechanical Engineers, Dec. 4 to 7, 1917, a great many matters were discussed and acted upon in which nearly all engineers are equally interested. Of the numerous sessions of the meeting, only a few of the most important can be referred too here. The Committee on Gages held an open meeting for the discussion of this important matter. Representatives from a large number of manufacturing plants and from several departments of the Federal Government were present. The question of gages and standardization of mechanical details is of course of paramount interest just now in connection with the manufacture of ordnance and ammunition. After discussion, the following recommendation was adopted by the meeting, for inclusion in all Government contracts for the manufacture of these materials. The maste and reference gages and standards of measurements, with which Ore

Jan 1, 1918

By A. D. Bryant

APPROXIMATELY 2 1/2 million tons of silica sand and ground silica with a value of $7.25 million is produced annually from the Ottawa, Illinois, district. These silica products come from the well known St. Peter sandstone formation which covers part of the Mississippi Basin extending from St. Paul on the north to the central part of Arkansas on the south and from Muncie, Ind., on the east to Kansas City on the west. Practically the whole state of Illinois is underlain by this formation except where removed by erosion. Sand produced from the St. Peter sandstone in the Ottawa district is noted for its purity, uniformity, and quality. In addition to various screened grades for industry about 10 pct of the total production of the Ottawa district is ground into silica flour for use in glass, abrasives, enamel, porcelain, tile, for foundry and filter sand, and other uses.

Jan 3, 1953

By H. E. Howe, A. A. Smith

E. Schumacher.*—Mr. Smith has shown us once again how variable lead alloys can be. I have studied lead alloys for a good many years and know from experience that their behavior cannot be predicted by analogy with other alloys. I have always been interested in observing how the creep resistance of lead may be improved by the addition of as little as 0.03 per cent Ca. Without the presence of calcium the grains of extruded lead pipe are fairly equiaxed and motion can take place easily at the boundaries. The calcium addition of 0.03 per cent causes the grain boundaries to become very irregular and jagged, and results in creep resistance many times greater than that of pure lead. Mr. Smith showed that in the one per cent antimony-lead alloy creep is occasionally excessive even where low stresses are involved. We have observed this phenomenon many

Jan 1, 1945

The old De Beers mine, which lies northwest of Dutoitspan mine at Kimberley, was the mine which launched Cecil Rhodes (In his historical career. It was the nucleus of the De Beers Mining Co. Ltd., formed in 1880, which later became De Beers Consolidated Mines Ltd. Inactive for more than a half century, the De Beers Mine is being rejuvenated for a new era of operations. Both mines were on the Vooruitzicht farm owned by the De Beers brothers, who had bought it from the Orange Free State Government ten years previously for £50. Although the brothers sold it soon after the discovery of diamonds at Dutoitspan, they are remembered for having given their name to the foremost diamond mining company in the world. Diamonds worth nearly R180,000,000 have come from this ground, and more will be recovered when the mine is re-opened.

Jan 9, 1963

By Guy T. McBride

The 1970's have been considered a pivotal decade for the mineral industries. Undergraduate mineral engineering education is relevant to this theme; in particular, there are three interrelated problems: 1) The goals, and therefore the course requirements, of the under- graduate curricula are in question; 2) The unit costs of undergraduate education appear excessive to those who bear the charges; and 3) The present social ambience detrimentally affects the work attitudes and career motivation of both prospective and in-course students. Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development and production levels. Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of society and the profession.

Jan 3, 1973

By D. W. Fuerstenau

The United States is rapidly approaching an acute shortage of minerals. According to some observers, this situation may even be more severe than the energy crisis because the US consumes nearly 30% of the world's mineral production. With the mounting competition for world mineral supplies, we can no longer take for granted that foreign mineral products will be available to the US as abundantly as in the past. In 1973, US consumption of mineral raw materials was $35 billion. Of this, $7 billion consisted of imports. Without a drastic reorientation towards the mining of domestic mineral resources, the 1973 $7 billion deficit might mushroom to $100 billion by the year 2000. Thus, a return to domestic sources of raw materials will become absolutely necessary-and will be bucking the trend of the past 25 years, characterized by capital investment for growth in multinational overseas mining operations.

Jan 11, 1975

A. W. AMBROSE, Washington, D. C.-Did you make any analysis of the amount of emulsion at the well and after you flowed it through a lead line to the storage tank? E. A. TRAGER.-B. S. can be formed in passing through a lead line by the friction due to the roughness of the pipe and the irregularities at the joints. R. W. MOORE.-Did you find the percentage of water to be limited to the percentage of oil in the emulsion which formed? E. A. TRAGER.- Yes, the percentage is about 67 percent. water and 23, per cent. oil. R. W. MOORE.-If you added more water would the emulsion be permanent? E. A. TRAGER.-Yes, it would be permanent, but the excess water would separate out. THE CHAIRMAN. (C. W. WASHBURNE, New York, N. Y.).-Did you use hot or cold water in these experiments?

Jan 12, 1919

By N. H. Cone

It is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

By William H. Mount

St. Joe Minerals Corp. has a long operating history of utilizing rubber-tired, trackless mining equipment in its Southeast Missouri Lead Belt underground mines. The company's first completely trackless mine, Hayden Creek, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and articulated diesel trucks. The trucks were comprised of a conventional scraper tractor unit matched with a rear-dump rock wagon. These machines featured the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an increasing portion of the underground haulage today. St. Joe's second completely trackless mine, the Indian Creek property, was opened in 1954; conventional 9.1-t (10-st) rear dumps were used for haulage. Main haul roads were designed to be wide and fairly level to accommodate speeds of 32-40 km/h (20-25 mph).

Jan 4, 1976

By N. E. Cone

IT is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

Jan 1, 1876

By Chester N. Truax

Still another shadow was cast over coal's largest market-the electric utilities-when President Johnson signed into law the Federal Clean Air Act of 1967. Air pollution-sulfur reduction-was thus brought into sharper focus as one of the central problems of the coal industry. Industry executives testified in both Houses of Congress to enable the lawmakers to develop a workable and economic law. The new legislation calls for the Secretary of Health, Education and Welfare to establish air control regions. After the regions are outlined the Department will publish air quality criteria on pollutants. Anticipating this legislation, the coal and utility industries have for the last several years been involved in extensive research programs to develop solutions to the air pollution problem. Even though the coal industry has been under strong attack for its part in adding contaminants to the atmosphere, it is by no means the major contributor.

Jan 2, 1968

By Richard L. Gordon, Charles J. Johnson

Electric power demand doubles about every ten years, and because of the associated burgeoning fuel requirements, power stations absorb over half of the coal output in the United States. Throughout the 1960's, demand for coal utilized to generate electricity grew at an average annual rate of 6.5% but coal producers held back greater expansion because they expected nuclear plants to proliferate faster than they actually did. Even so, the growth rate is expected to continue at the 1960's rate until at least 1976. The continuation of the 6.5% growth rate beyond 1976, however, will require additional orders for coal-fired plants during the early 1970's. In fact, plants consuming a total of 130 million tons of coal must be ordered in the next few years. If the requisite plants materialize, total 1980 coal output for electrical power generation will be approximately 600 million tons.

Jan 1, 1971

By C. F. Kelley

IT is no new experience for the distinguished subject of this presentation to be the recipient of honors conferred, to be eulogized for successful accomplish-ment, or to hear expressed with sincerity the admira-tion of his fellows. The objectives of his professional endeavor have taken him to many fields; the scenes of his labors have varied from the most remote corners of the globe to those which are close at hand; the universality of his experience is an epitome of modern life, impossible of occurrence in any other era. His career not only embodies to an unrivaled degree the opportunities of the contemporaneous epoch, but also exemplifies in the manner in which they have been transformed into successful accomplishments the pos-sibilities of our age. The many-sided career of our medallist is a composite. Tonight we deal chiefly with its phase for which this medal has been bestowed.

Jan 3, 1928

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By Joseph W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles, as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain.

Jan 3, 1960

By Byron S. Gottfried, Guan Qi Zhao, John W. Tierney

Equations for predicting the performance of vacuum filters and centrifuges used for coal dewatering are presented. These equations are the basis for a dewatering module which has recently been added to the Coal Preparation Plant Simulator developed at the University of Pittsburgh under the sponsorship of the Department of Energy. The module provides for mechanical degradation in the centrifuge; loss of fines to centrate or filtrate; changes in size and gravity distribution; changes in ash and sulfur content; as well as final moisture content of the dewatered product. Inputs to the module are the flow rate of the coal to be dewatered, a washability analysis of the coal, and parameters describing the operation of the vacuum filter or centrifuge. Typical results obtained using the module are presented. There are adjustable parameters which can be varied to match plant operation or experimental data if desired.

Jan 1, 1983