Search Documents

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN'I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By A. S. Richardson

The recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont,., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968

By W. H. Schacht

In the Lake Superior District, the air indoors must be heated continuously during eight months of the year and occasionally during the remaining months. Incident with mining in this district, therefor?, there is need for heating many of the buildings connected with these operations. In addition to the mine buildings, that is, shops, engine houses, offices, change houses, etc., such public buildings as schools, library, and theater, when close to the mines, are often supplied from the mine heating mains. At the Copper Range Company's mines, Champion, Trimountain and Baltic, the heating surface thus supplied from the mine mains is over 50,000 sq. ft. (4645 sq. m.) which requires a steam consumption, at times, of 18,000 Ib. (8165 kg.) per hour, or the equivalent of a rate of ovcr 50 tons of coal per day (were live steam used). This figure is based on a consumption of 1/3 Ib. per sq. ft. of heating surface during the coldest weather, and provided the system is not wasting steam by blowing it to the atmosphere or into the return line on account of leaky traps, which so often is the case. Under the latter conditions, steam consumptions of three to four times the above rate are not uncommon. This shows that the cost of heating is of enough importance to he given serious consideration, especially at this time of rising prices of fuel. The power and heating value of exhaust steam arc appreciated by most engineers, and its application for such purposes is general. At our stamp mills, the exhaust from the stamps is used to operate low-pressure turbines, thus reducing the former water rate per horsepower developed by more than 50 per cent. At the above-mentioned mines, electric motors have replaced the many small steam engines, so that this supply of exhaust steam has been practically eliminated. The larger engines are compound, triple, or quadruple condensing. The hoists, however, in all cases are simple and non-condensing and of two sizes, namely, 24 by 60 in. and 32 by 72 in. (61 by 152 cm. and 81 by 183 cm.). These hoists now offer the only available supply of exhaust steam; but as this flow is intermittent and varies from extreme violence to zero, the steam so discharged cannot be

Jan 1, 1922

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a very general loosely used term that includes virtually all finely divided types of limestone as well as burned forms of lime. However, actually (and according to Webster) lime is only calcined limestone (known as quicklime, calcium oxide, or calcia). It also embraces the secondary product of quicklime-namely hydrated lime or slaked lime (calcium hydroxide). Fundamentally there are two basic types of limestone-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts in terminology. The only difference is that the dolomitic types are a combination of the elements, calcium and magnesium, whereas high calcium limes contain only 0.5 to 2 pct of magnesium. Both types, which are made through calcination at high temperatures, are shown chemically as follows: [ ] In the above reactions either type of limestone is burned (calcined) in furnaces known as lime kilns so that the carbon dioxide content of the stone is expelled as a gas. With high calcium limestone 44 pct of the weight of the stone is lost; with dolomitic limestone the loss is 48 pct. Also, both reactions are chemically reversible since quicklime absorbs carbon dioxide readily and in so doing transforms itself back to the original carbonate form. Most quicklimes correspond in size to the original rock, which varies from one to eight inches, depending upon the type of kiln employed. Slight shrinkage occurs during calcination. A few limestones when calcined will decrepitate (break down) into a fine powdery form; however, chemically it is the same as the pebble or lump-sized material. For some uses the lumps of quicklime are pulverized and packaged. Since quicklime has great affinity for moisture and carbon dioxide, it is perishable. When it absorbs moisture and CO2 slowly from the atmosphere, the resulting product is "airslaked." Consequently, it must be stored in dry, moisture-proof areas that are free from CO2. Because of its fugitive nature, it is usually consumed within a few weeks after manufacture. A more stable form of lime is hydrated lime-commercially made by adding water to the quicklime until the lumps break down into a fine, white powder. This product, which is usually packaged, can be stored more safely; and many of its uses are interchangeable with quicklime. The irreversible chemical reactions of hydrated lime for both high calcium and dolomitic types are: [ ]

Jan 1, 1960

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By F. H. Parsons

At the time that converting or bessemerizing of copper matte first began to be practiced by the smelters in the copper industry, converters were lined by tamping the flux, usually siliceous ore, into the steel shell. About 1910, practice in several plants had demonstrated the superiority of a basic lining of nonfluxing material and the addition of flux through the mouth of the converter. Adoption of the new method by nearly the entire industry followed. Basic linings are made of refractory "magnesite" brick manufactured, usually, from imported dead-burned magnesite. Either the linings are laid up in the shell dry or the bricks arc bonded with some mortar dictated by the preference of the user. Foreign, usually Austrian, magnesite was the main source of supply for these bricks, although there were domestic sources, but it was not until costs began to rise a few years after the first use of basic linings that these domestic sources were investigated to any great extent. Exigencies created by the World War necessitated the use of the domestic magnesite during this period, but the brick manufacturers reverted to the use of the foreign product after the war, because the impurities therein made a brick with a better fire bond than the purer domestic magnesite. Therefore the domestic product became available at a favorable price for any metallurgical process that permitted its use. The United Verde converting practice using magnesite linings has resulted in a high consumption of magnesite because of the zinc content of the low-grade matte. It was realized that the cost of these linings represented a large portion of the cost of converting, and an investigation was started to find means by which these costs might be lowered. In the neighboring state of California rather pure magnesite was being mined and treated for the market. The product, however, was purposely made to simulate the dead-burned grain magnesite product from foreign sources by the addition of fluxing impurities before burning. It was learned that this dead-burned California grain magnesite could be laid down in Arizona at a price one-third that of the same tonnage of "magnesite" brick manufactured from foreign magnesite. It was also learned that at least one California producer was ready to supply the market with periclase, which was a grain magnesia produced by burning the

Jan 1, 1934

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By S. Le Fevre

The application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted,in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration. The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to $ or 8 in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills. The power from the first plant was distributed to Mills 1 and 2, one 2,500 cu. ft. compressor, and to the Harmony hoist, which was driven by a 300-h.p. motor operating four 10-ft. drums. Our experience with the hoist covers largely the development of electric hoisting from 1903 to date, and in some cases improvements were worked out to satisfy our needs. The motor is still operating as installed, but the control apparatus has been radically changed several times. When installed, the iron re-

Jan 1, 1915

By S. K. Tarby, W. O. Philbrook

Limited experimental data and a critical review of the literature are given to indicate that the true equilibrium distribution of manganese between carbon-saturated iron and blast-furnace type slags has not yet been satisfactorily established as a function of the composition, temperature, and pressure of the system. THE distribution of manganese between carbon-saturated iron and blast-furnace type slags has been studied by a number of investigators.1-7 Generalization of the results of these works indicates that the weight percent distribution ratio, (%Mno)/[%Mn], decreases with increasing temperature and slag basicity, in accord with thermodynamic data and practical observation. However, where comparisons among these studies can be made for similar slag compositions and temperatures, the reported values of the manganese distribution ratio are discordant. The variations are attributed to failure of the experimenters to bring their systems completely to equilibrium with graphite and CO at 1 atm, as judged by departures from silicon equilibrium. Even in the most recent work,5-7 this problem was recognized but the authors made the questionable assumption that equilibrium could prevail for manganese distribution even though other reactions were still in progress. Manganese equilibrium values for three particular slag compositions were required incidental to a kinetic study8 and were determined experimentally. Special pains were taken to approach concurrent equilibrium with respect to silicon. Although the results were not completely definitive, they indicate that the true manganese equilibrium distribution ratios are lower than have heretofore been reported. The data are presented together with a brief commentary on the literature to suggest the need for further work in this area. EXPERIMENTAL METHOD Equilibrium runs were carried out in a stationary, induction-heated graphite crucible closed by a graphite lid and flushed continuously by a slow flow of carbon monoxide at 1 atm pressure. Temperature was controlled manually within ±3 deg C with the aid of immersed thermocouples in mullite tubes protected against slag attack by graphite sleeves. The desired temperature was established by a calibrated Pt vs Pt-10 pct Rh thermocouple and control was then maintained using a more stable W-Mo couple. Runs were made at 1500º and 1575ºC for durations of 7.5 to 10.5 hr. The charges were calculated to yield 400 g of metal and 100 g of slag. The primary slag compositions and designation numbers were as follows:

Jan 1, 1963

By R. J. Sullivan

DURING the past twelve months the Loudon pool of the Eastern Interior Coal Basin has become established as one of the two largest discoveries since the revival of exploitation in the Illinois region and now occupies a position among the important pools of the United States. On Aug. 1, 1939, production averaged 54,000 bbl. per day from 990 wells, having accumulated a total of 10,305,000 bbl. Its very active develop-ment promises to continue for fully another year. It is the site of one of the industry's most singular large-scale gas-injection programs. LOCATION AND RESERVOIR CHARACTERISTICS At present the pool embraces an area 15 miles long by 3 ½ miles wide in eastern Fayette County, along the western rim of the now well-known Illinois Basin's deeper part, through townships 6, 7 and 8 north and ranges 2 and 3 east of the Third Meridian. It is the northernmost, and most prominent, productive structure of a group extending over a 50-mile trend southward to the Dix pool of Jefferson County. Three horizons have been proved to carry production-namely, the Weiler sandstone at 1390 ft., the Paint Creek sand at 1460 ft. and the Benoist or Bethel, at 1500 ft. Geologically, they fall in the Chester series of the upper Mississippian system, where much of Illinois' early-day oil was found, having been laid down in shallow off-shore waters as a part of the vast delta deposit underlying central Illinois and parts of Indiana and Kentucky. As a result of this type of sedimentation, followed by repeated uplifts and warping along an anticlinal axis, differ-ential deposition of sands and shales contributing to great irregularity took place. This is further reflected by wide variations in permeability, porosity and thickness of all the sands and, accordingly, in the producing characteristics of wells. Permeabilities range as high as 550 millidarcies, with the average commonly lying between 60 and 100. For the three pay horizons the mean porosity is 18 per cent, at a calculated water saturation of roughly 30 per cent. The Weiler sand has an average thickness of 25 ft., the Benoist of about 23 ft. and the Paint Creek of approximately 18 ft. Of these three productive formations the Benoist

Jan 1, 1940

By Walter C. Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1 1/3 miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1938

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By Eugene F. Poncelet

Glass squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. Experimental Procedure Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2½-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through'' of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1947