Search Documents

By H. B. Charmbury, D. R. Mitchell

Recovery of fine coal from solids reporting to wash water has become increasingly important. These solids range from about 28 mesh to 0 and constitute 3 to 7 pct by weight of the feed tonnage to a coal preparation plant. In the past they were usually wasted to streams, but present clean stream legislation makes it necessary to remove them from the wash water and, if economically possible, recover the associated coal as a saleable product. Where these solids are not wasted to streams or to slime ponds they are recovered by thickeners and filters. Since filter cake is often high in ash or sulfur, or both, it is not readily marketed or used. Common practice is to mix it with other plant products, generally slack or cleaned run-of-mine. Uniform blending is difficult, not only because the impurity is usually high, but also because during certain operating periods it is possible to get a concentration of this filter cake in a railroad or barge.

Jan 2, 1959

By R. V. Horrigan

High purity ZrC14 (25 to 200 ppm of metallic impurities) can be readily prepared in simple apparatus by thermal decomposition of alkali chlorozirconate fused salts at 500° to 600°C and at atmospheric pressure. Suggested phase diagrams for the systems NaCI-ZrC14 and KCI-ZrCI, are presented. ALKALI chlorozirconate compositions — anhydrous fused mixtures of ZrCl4, NaC1, and KC1— are manufactured commercially and are used by the magnesium industry to introduce zirconium into magnesium alloys. Zirconium refines the grain size and improves the physical properties of many important magnesium alloys. In the course of working with chlorozirconate compositions of high ZrCl4 content, it was noticed that these salts decomposed progressively itwaswith increasing temperature to yield considerable amounts of a ZrCl4 sublimate of high purity together with a solid chlorozirconate residue. Further research led to: 1—improvements in the

Jan 1, 1956

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a short computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

By W. H. Jr. Meyer

Although an aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph provided some form of radial-line method is used to determine the true position of images. The slotted-templet method, which is based on the well-established radial-line principle, has made it possible to construct accurate mosaic maps at a cost comparable with that formerly charged for the average mosaic. It makes possible the securing of these results with far less ground control, which is always expensive. It has expanded widely the possible use of aerial photographs for mapping. ALTHOUGH a vertical or oblique aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph. Some ground controls or data are needed, the number and accuracy to be governed by the mapping method to be used and the scale and final accuracy desired in the finished map.

Jan 1, 1939

By J. A. Eisele, D. J. Bauer, L. E. Schultze

Approximately 100 million mt of magnetic reject tailings, which contain apatite and about 1% yttrium and rare-earth elements, exist in the eastern U.S. as a result of iron ore mining operations. At the present time, no economic process is available for recovering yttrium from this material. The U.S. Bureau of Mines (USBM) studied the problem to determine if an effective low-cost method could be found, thereby increasing our domestic yttrium reserves. [Fig. 1] is a line drawing of a photograph taken during microprobe analysis of a sample of the tailings, and shows the distribution of yttrium. Typical analysis of this material is 0.14% yttrium and 1.1% rare-earth elements (mainly lanthanum through neodymium). Over half of the yttrium is present as a hydrated Ca-Y silicate deposited along interfaces in the grain structure; whereas, the remainder of the rare-earth elements occur as Ca-Fe-RE silicates. The remaining yttrium and rare-earth elements are in solid solution with the

Jan 1, 1977

By Ernest N. Patty

Placer gold-bearing gravels of interior Alaska and the Yukon are, for the most part, permanently frozen, and are described as permafrost. The first step in preparing these gravels for dredging is to strip by bulldozer the surface layer of tundra, brush, and scrub timber, and to expose the ebony colored surface of the frozen mud at the grass roots. This mud varies from a frozen, muddy ooze to a sandy silt and locally may contain layers of peat. The whole mass is intercalated with ice dikes and lenses. The thickness will vary from a few feet up to 100 ft, depending upon local conditions. A freshly exposed surface will thaw to a depth of 4 in. per day during the summer season. Common practice is to expose a large surface of this mud to the sun and each day's thaw is then swept off by water and carried away in suspension.

Jan 1, 1951

Western Mining Corp. has announced plans to expand its mining operations at Kambalda, and to build a nickel refinery at Kwinana, near Perth, Western Australia. The refinery will use the ammonia-leach hydrogen reduction processes of Sherritt Gordon Mines Ltd., and it is expected that by 1970, when the expansion is scheduled for completion, Western will be the world's fourth largest nickel producer. Although estimates have not been finalized, the total cost is expected to be about $55 million. The mine and mill facilities at Kambalda, which began production in June 1967, are now producing at the rate of 11 million lb of contained nickel per year. The company estimates the sulfide ore reserves at Kambalda and St. Ives at 10.4 million tons averaging an usually high grade of 3.8% nickel, or about 790 million lb of contained nickel. In addition, silicate and oxidized ores have been located in both areas.

Jan 3, 1968

By Guy R. Johnson

Like many other similar plants the ore-washer of the Longdale Iron Company has been a growth of years. In its principal features there is probably nothing new, as the type is that of the well-known " log-washer." Some of its minor details may, however, be of interest to those members who have to deal with the washing of large quantities of brown iron-ores, the principal gangue of which is clay. * Until 1883, the ore at Longdale, being of unusual purity, needed no washing, and was charged to the furnaces as it came from the mines—both lump and fine—the only attempt at cleaning being the' picking over a screen of 1½-inch iron bars, 3½ inches from center to center, set in the top of the bins through which the cars for the furnaces were loaded." In 1883 it was no longer possible to win the ore by open cuts, and regular underground work became necessary. It was very

Jan 1, 1895

By George Ashley

IT has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. TABLE 1.-Pittsburgh Coal Bed to Dec. 31, 1934 Estimated Recov- State Thousands of ( Value erable Reserves Tons Mined (1935), Thousands of Tons Pennsylvania 3,144,000 $4,922,000 7,500,000 Ohio 493,391 843,699 3,000,000 West Virginia 650,000 1,027,000 5,500,000 Maryland 183,224 254,681 20,000 Totals 4,470,615 $7,047,380 16,020,000 PRODUCTION AND VALUE In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately.

Jan 1, 1936

T. M. Morris (Measurement and Evaluation of the Rate of Flotation as a Function of Particle Size, P. 794), was the commanding officer of a patrol craft charged with guarding Aleutian waters against infiltration by the Japanese during World War II. Before going into service, he was an assistant research engineer with Anaconda Copper at Anaconda, Mont., and later a metallurgist with Tennessee Copper Co. Presently he is a professor in the Department of Metallurgy, Missouri School of Mines, Rolla, Mo. A member of the AIME, he is a graduate of Columbia University and the University of Missouri, with a Bachelor of Science, Master of Science and a Ph.D. Professor Morris is the author of a previous paper for the AIME, Measurement of the Equilibrium Forces Between an Air Bubble and an Attached Solid in Water. An outdoor man by predilection, he enjoys bird watching and hiking in his free time.

Jan 1, 1952

By A. Eiders

THE year 1874 marks a decided advance in the metallurgy of the West, in two directions. On the one hand, the technical management has been very materially improved, and on the other, the production has been largely increased over that of the previous year. The technical improvements of greatest importance are the introduction of condensation-chambers, or flues, at several works, and the further treatment of the lead matte produced in the ore smelting. These two are of general importance, and although by no means introduced at the majority of works, their adoption at the few where their great importance has begun to be understood will no doubt bring about their universal introduction. To these may be added a third step. forward, which for some localities is vital enough, though for others it must still remain doubtful whether it is to be regarded as an improvement or not. This is the introduction, at several

Jan 1, 1875

By A. Eilers

The year 1874 marks a decided advance in the metallurgy of the West, in two directions. On the one hand, the technical management has been very materially improved, and on the other, the production has been largely increased over that of the previous year. The technical improvements of greatest importance are the introduction of condensation-chambers, or flues, at several works, and the further treatment of the lead matte produced in the ore smelting. These two are of general importance, and although by no means introduced at the majority of works, their adoption at the few where their great importance has begun to be understood will no doubt bring about their universal introduction. To these may be added a third step forward, which for some localities is vital enough, though for others it must still remain doubtful whether it is to be regarded as an improvement or not. This is the introduction, at several

By C. T. Sheeran, J. C. Franklin

A commercially available microprocessor-based system capable of monitoring 512 channels has been interfaced with monitors for radon, working level, air velocity, and fan power. The basic system utilizes both 280 and 8080 microprocessors in a desktop central processing unit (CPU). CPU hardware includes keyboard, video display (CRT), and disk drive; a printer is used to keep permanent data records. Signals from all channels are transmitted to the computer in digital form where they are processed for alarm status. Software developed for the system allows for audiovisual alarms in the event of low and high readings, rate change, change of state, or communica- tion failure. Up to six channels can be continuously displayed on the CRT for current readings. Shift reports and trend logs may be generated to help the ventilation engineer determine average working levels and ventilation effectiveness. Additional software permits the operator to program command sequences which may be used to automatically restart fans after a power outage.

Jan 1, 1982

By Kenneth L. Temple

ACID coal mine drainage presents a peculiarly difficult problem for two principal reasons. First is the fact that the amount of acid water discharged from active and abandoned mines constantly in- creases as coal fields are developed and thereby creates a steadily worsening nuisance of rapidly growing importance to the general public as well as to the coal industry. Second is the even more significant fact that there is no method yet known that will appreciably alleviate the acid water problem except at totally prohibitive cost to the coal operators. The problem is thus seen to be an urgent one. With a growing need for good quality water and a growing public demand for abatement of stream pollution, a large portion of the soft coal industry finds itself in the position of year by year dumping more and more acid into the streams and waterways and having no way in sight of improving the situation or even of keeping it from getting worse.

Jan 12, 1951

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

By Richard F. Link, George S. Koch

About 50,000 assays of mine samples were required in a preliminary investigation of the distribution of gold, silver, lead, copper, and zinc in two large Mexican mines, the Frisco mine at San Francisco del Oro (Chihuahua) and the Fresnillo mine at Fresnillo (Zacatecas). The feasibility of working with so many assays rests directly on the use of machine processing methods. The purpose of this article is to describe the methods used because machine (or data) processing can also be used efficiently to make the many calculations from mine assays needed in mining operations. No particular originality is claimed for these methods, which are straightforward applications of standard procedures for machine processing. Inasmuch as machine processing is essentially a routine job once it is begun, procedures must be organized more completely than is the case where human judgment can be inserted at every step. Before undertaking any work, it is necessary to decide carefully just which data must be processed as well as the exact results desired.

Jan 9, 1960

By George H. Cook

At first sight this subject seems to belong to pure theoretical geology, but examination will soon show that it has important practical and economic interest to the mining engineer. The conclusion that all the northern portions of our country, as well as of the eastern continent, have, in the later periods of geological history, been covered with a thick bed of ice, is now accepted by geologists. This bed of ice, except in its greater magnitude, was like the modern glaciers of the Alps, and other mountains which extend above the line of perpetual snow. The marks it has left upon the surface show that it was comparatively thin on its southern edge, but that its thickness was much greater a little further north, and that it was several thousand feet thick at its kenviest parts. This variation of its surface would give it a descending slope towards the south, and cause the mass of ice, like a semifluid substance, to move in that direction,

Jan 1, 1879

By H. M. Merry

THE graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts, the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution; percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required.

Jan 9, 1919