Search Documents

By K. E. N. Hanney

INTRODUCTION Slurry systems and mechanical conveying, represent the main methods of transporting solids from one area of a mineral processing plant to another. A well-designed slurry handling system can assist in lowering plant capital costs by reducing building size, simplifying plant layout and reducing operating costs by lowering maintenance and labour costs. This Paper has been prepared with the object of providing a practical approach to designing slurry systems. SLURRY CHARACTERISTICS Slurry is a mixture of crushed or ground rock mixed with water or a chemical solution, and can flow under several different conditions: (a) As a homogeneous suspension; (b) As a heterogeneous suspension; (c) With a moving bed (saltation); (d) With a stationary bed. Homogeneous flow takes place when the solids are uniformly distributed throughout a pipe and when particle sizes are smaller than 325 mesh. Heterogeneous is the most common slurry suspension. In this system, there is a gradual increase in concentration of solid particles towards the bottom of a pipe. There is a fairly wide range of velocities that fall within this system. In moving bed systems, the coarse particles settle out and bounce along the bottom of a pipe. Operating under these conditions tends to minimize wear and power requirements, but because this system operates within narrow velocity limits, pipelines frequently plug. Stationary bed conditions exist when coarse material has settled in the bottom of the pipe restricting the available area. These conditions should be avoided. DESIGNING A SLURRY SYSTEM Slurry can be transported either by pumping through a pipeline or by developing a gravity head and flowing through a pipe or along a launder. When considering any slurry system, whether for the design of a new plant or to make modifications to an existing operating plant, design criteria are required. The design criteria provide the information for calculating the material balance and sizing the equipment. The quantities on the material balance can then be assigned to the flowsheet for reference. The equipment can then be laid

Jan 1, 1982

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By William Catron, Cyril U. Colledge

BECAUSE the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It was clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stopes below with disastrous results to men and mine. The method of mining developed during the years 1928, 1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. GEOLOGICAL STRUCTURE The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1938

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By F. C. Farnham

THERE has been very little, if any, uniformity in the reference datum used for magnetometer surveys. It has been the practice to choose a base station at which the magnetic field is assumed to be normal and call the difference in field strength between a given station and this base the anomaly at the given station. For small-scale surveys latitude and longitude corrections may or may not be applied, but for large-scale surveys such corrections usually are applied. The United States Coast and Geodetic Survey maps showing lines of equal magnetic intensity are commonly used to determine the normal latitude and longitude variation by scaling values from the map for given points and computing the change per mile north and the change per mile east. This method has been quite satisfactory for isolated surveys, but when two surveys originating at different base stations were extended until they joined, difficulty arose, not only because of discrepancies between base-station values, but also because of differences between the latitude and longitude correction factors used for the separate surveys. It is the purpose of this paper to describe a reference datum for magnetometer surveys which, it is believed, will eliminate most of the difficulty arising from this source. In order to be satisfactory, a general datum for magnetometer sur-veys should be as close as possible to the observed field and still he based on some assumed distribution of magnet poles, in order that the "normal" value of any component of the field for any given point may be computed to as many significant figures as desired. Such a field has been com-puted, and a comparison of the intensity of its vertical component with the average vertical intensity for the United States as shown by the U.S.C.G.S. map of lines of equal intensity for 1935 is shown in Fig. 1.

Jan 1, 1939

By Oswald J. Heinrich

THE serious objections to the Leblanc soda process may be enumerated as follows : 1st. The total loss of sulphur employed, equal to about one-third of soda produced. Various processes have been proposed to regain this sulphur, but none have come into practical operation on a large scale. 2d. The great bulk of waste products, equal to nearly twice the amount of soda, which forms a serious annoyance about the works. 3d. The complicated series of operations necessary. 4th. The large amount of labor and fuel required. 5th. The production of noxious gases which necessitate extensive condensing arrangements. 6th. The large capital necessary for the erection and maintenance of the plant. These objections have long been recognized, and many attempts have been made during the last thirty or forty years, to discover and introduce a cheaper and more direct method for the manufacture of this important staple. The reaction between bicarbonate of ammonia and common salt, whereby bicarbonate of soda, insoluble in a solution of chloride of ammonium, is precipitated, has been closely studied for the last twenty-four years, on account of its simplicity and the purity of the product it affords. This ammonia-soda process is now so far developed, that while it is not .in position to entirely replace the Leblanc process, yet it can successfully compete with it where the conditions and localities are favorable. The advantages of the ammonia-soda process may be summed up as follows : 1st. It is independent of the essential agent in the Leblanc process, viz., sulphuric acid, and hence can be established in those localities where salt is abundant, and yet where sulphuric acid could not be made, or where it could not be transported profitably. 2d. The ammonia-soda process being a " wet" process, the evaporation of salt brines to obtain the solid salt required in the Leblanc process, is rendered unnecessary. 3d. The direct conversion of chloride of sodium into bicarbonate of soda, which can readily be converted into the maketable monocar-

Jan 1, 1879

CONTENTS PAGE WARNER, ROBERT K.-Efficiency of Screening. Discussed by Robert C. Canby,Robert K. Warner, W. 0. Borcherdt, V. E. Flanagan 1 FAHRENWALD, A. W.-Surface Reactions in Flotation. Discussed by Arthur F. Taggart, A. M. Gaudin 7 Efficiency of Screening Discussion of the paper of ROBERT K. WARNER, presented at the New York Meeting, February, 1924, and issued, as Paper No. 1293-M, with MINING AND METALLURGY, January, 1924. ROBERT C. CANBY, Wallingford, Conn.-On page 2, the author speaks of the importance of using a testing sieve clothed with the same material as the screen being studied; does he regard this as essential? In practice, how does the screen efficiency calculated by the difficult-grain method compare with those computed by the usual undersize method? Is it possible by the author's method, to obtain a measure of efficiency that can safely be compared with that of another screen sizing a different ore? ROBERT K. WARNER.-The use of a testing sieve clothed like the mill screen being studied is desirable but not essential for routine work about a mill where the character of the feed varies little, as regards the shape of the grains and the sizing test. Close agreement in size of aperture between the sieve and the screen is, however, important if the data obtained are to be valuable to others working on a different feed. If the testing sieve is coarser than the mill screen, the efficiency will appear unfairly low; whereas if it is too fine one might get efficiencies greater than 100 per cent. because of the apparent oversize in the undersize. In either of these cases the usefulness of the difficult-grain method of calculation would be reduced. As screens wear, the undersize grows appreciably coarser so that it is desirable to test screens only when the cloth is new or else to provide testing sieves that are worn about the same amount. The futility of making efficiency observations on a. distorted or broken screen surface is obvious.

Jan 6, 1924

By L. C. Campbell

The purpose of any accident-prevention program is the curtailment or entire elimination of injuries and fatalities. It is a job that is never finished in the coal-mining industry. Day by day, on shift and off shift, men are exposed to injury and death in varying numbers. Seldom is it possible to lock up at the end of the shift and leave a mine plant in the care of a sleepy watchman, as can be done at most manufacturing plants. Even on off shifts there are maintenance and supply crews, coal cutters, pumpers and ventilation men exposed to danger. The prevention program of The Koppers Coal Co. recognizes two primary facts: First, no program can be successful without the full support of the management and complete knowledge of the job at hand on the part of every supervisor. Second, and equally important, is the full cooperation of every employee in observing the safety rules and practices set up by the management. Conscious day-to-day concern for his safety by the individual worker is the longest stride toward a good safety experience. How to accomplish the education of the individual worker and supervisor for safety is the problem of The Koppers Coal Co., as it is the problem of all coal companies. Safety Rules A simply stated set of Safety Rules and Practices for the government of employees is the starting point with The Koppers Coal Co. There are but 13 of these rules, which are short, easily understood and followed by a campaign of education and inspection. Each employee receives a set of these Safety Rules and Practices and signs a receipt for them, which is bound in at the back of the booklet, and this receipt becomes a part of his employment record. These rules and practices are as follows: Introduction The following rules have been compiled for the safety of employees and are established according to rules number one and number two of the official bulletin

Jan 1, 1940

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By Leland Van Wert

IN 1888, Howard,1 working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200° to 350° C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.3 He described (for nonaustenitic steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300° C., or below 200° C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200° to 300° C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200° and 300° C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity if, nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them? To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931

By Persifor Frazer

"The nebular theory is a noble speculation supported by plausible argument, and the verdict of science on the whole subject cannot be better expressed than in the words of Newcomb :—'At the present time we can only say that the nebular hypothesis is indicated by the general tendencies of the laws of nature, that it has not been proved to be inconsistent with any fact, that it is almost a necessary consequence of the only theory by which we can account for the origin and conservation of the sun's heat, but that it rests on the assumption that this conservation is to be explained by the laws of nature as we now see them in operation. Should any one be skeptical as to the sufficiency of these laws to account for the present state of things, science can furnish no evidence strong enough to overthrow his doubts until the sun shall be found growing smaller by actual measurement, or the nebulæ be actually seen to condense into stars and systems.' " Leibnitz2 is credited by Cuvier3 (who associates with him Descartcs) with " amusing their imaginations " by conceiving the world to be an extinguished sun or vitrified globe upon which the vapors, condensing in proportion as it cooled, formed the seas, and afterwards deposited the calcareous strata. Whiston4 believed the earth was crested from the atmosphere of one comet and deluged by the tail of another. The heat which remained from its origin excited the whole antediluvian population, men and animals, to sin, for which they mere all drowned in the deluge, except the fish, whose passions were apparently less violent. De Maillet5 held that the globe had been covered by water for many thousand years. The terrestrial animals were originally inhabitants of the sea, and man himself began his career as a fish. He adds it is not uncommon to meet with fishes in

Jan 1, 1905

By A. J. Miller, G. R. Brophy

THE Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Grossmann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al .4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be expected that similar results would be obtained. Crafts and Lamont, in their second paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater5 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors underevaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. [ ] More recently W. Steven6 has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were

Jan 1, 1945

By Marcel Schlumberger

The electrical methods for surface-prospecting have been well developed in the last 20 years. The method involves, in the classic form, the sending of an electrical current into the soil, by means of two electrodes A and B, and studying the potential distribution at the surface, by measuring the difference of potential between pairs of points such as M and N. The points M and N are usually placed on a line between, and equidistant from, A and B. By increasing the distance AB, the current sent into the Earth, and likewise the distribution of surface-potentials, become influenced by regions of greater and greater depth below the surface. By varying the form and dimensions of the electrode-arrangements AMNB, called a "quadripole," one may make valuable deductions concerning the nature or thickness of beds, if one knows the electrical properties of these beds. On the other hand, if the form and dimensions of the electrodes AMNB remain fixed, the depth of penetration of currents in the Earth remains, so to speak, almost constant, although it tends to increase where the subsoil is more conductive, and conversely. Therefore, if one moves the constant-dimension quadripole over all the terrain to be Investigated, one achieves approximately a horizontal exploration. This permits a study of tilted beds or faulted horizon-tal beds. When the particular problem becomes deep, of the order of 2000 meters, or more, it is ne-cessary to Increase the distance between the current-sources AB to a length such that the work 'comes very troublesome, especially if the region is wooded. At the same time, the separation the points M and N must be likewise great (for example, one km) in order to obtain differences potential which are not too small; the measurement of potential differences across MN is then difficult because of the presence of parasitic potentials, due to a flow of telluric currents in fourth, and the order of greatness of these currents may exceed the quantities to be measured.

Jan 1, 1940

By V. (“Viv”) R. Forbes

[ ] INTRODUCTION "The Liberal Party believes that the State's mineral resources belong to the people of Queensland and therefore it is essential that the state, on their behalf, obtains maximum benefit from the development of those resources." (Liberal Party, 1980 "Mineral Resources Policy" p.2). "Unless sound policies are implemented.... increased production of minerals will benefit only the already wealthy and the lucky few... A resources tax is essential to ensure that above normal profits are shared by the whole community.... Labor policies on taxation must ensure an adequate return from mining developments to the Australian people." (Labor Party Policy Paper, May 1982 "National Issues relating to rapid expansion of mineral production during the eighties". p.1, 37, 47). Judging from these statements, key political parties in Australia believe that mining profits are lightly taxed and that shareholders get most of the benefits. THE REALITY The Government Share of Income statement in Table 1 attempts to measure the government share of the income generated by the "Big Five" Australian mining companies - Broken Hill Pty Ltd. (BHP), CRA Limited, Utah International, MIM Holdings Ltd., and Western Mining Corporation ("WMC"). These companies control over 70% of Australia's mining industry including all the most profitable mining operations. They dominate the mining and processing of iron and steel, aluminum, manganese, coal, oil and gas, copper, lead, zinc, silver, nickel, gold, ferro-alloys and salt in Australia. They are also major world exporters of most of these products. They are thus a representative sample of the profit-earning side of the Australian mining industry. In their two most recent financial years these five companies had income before tax of A$6,980 million. The Government share of this income was A$6,285 million or 90%. The total market capitalisation of the Big Five is about A$8,480 million. (December, 1982). Governments thus consumed the equivalent of 82% of their total value in just two years. This was taking place while the politicians drafted the above statements calling for an "adequate" share for the people.

Jan 1, 1985

By Allen D. Garrison

The chemistry of clays and shales has been assuming increasing importance in the petroleum industry, and two factors have greatly influenced this trend. The first has been the growing evidence that the marine shales are source beds, and that the petroleum compounds have migrated to the sand reservoirs overlying or underlying these shales: the second has been the demand for drilling fluids better adapted to penetrate these marine shales without difficulty and expense. Origin and General Composition of Clays and Shales Clays, shales and surface soils are all closely related materials. They are mixtures of finely divided compounds formed during the weathering of the solid crust of the earth. Their nature is essentially colloidal; that is, their behavior is determined by the state of division of the materials and the surface reactions of the smallest grains. Many of their chemical changes affect only the exposed areas and do not involve the interior of the grains of matter. The extent of these reactions is more nearly proportional to the area of the substances than to their mass, therefore it is possible for a small amount of a material in an extremely fine state of division to completely dominate the character of the mixture. More than 83 per cent of the crust of the earth is composed of three elements—oxygen, silicon and aluminum. Consequently, the corrosion products of the crust are predominantly aluminosilicates, or compounds of aluminum, silicon and oxygen. If we add the compounds of six elements—iron, calcium, sodium, potassium, magnesium and hydrogen—more than 98 per cent of the crust has been accounted for. These six elements, together with the first three, also appear in soils, clays and shales. But direct chemical analysis is of little value in describing the nature of such materials. Many chemical individuals may be present in variable amounts, and the extreme subdivision of any one of the individuals may contribute qualities that dominate the mixture.

Jan 1, 1939

By Harold A. Linke

The following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Handbook and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman. Launder Slopes The main object in the study of launder slopes is to provide grade steep enough to prevent "sanding" by a safe margin, and to avoid

Jan 1, 1943

By P. B. Elkin, K. C. Ten Brink, Allen D. Garrison

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940

By Allen D. Garrison

The chemistry of clays and shales has been assuming increasing importance in the petroleum industry, and two factors have greatly influenced this trend. The first has been the growing evidence that the marine shales are source beds, and that the petroleum compounds have migrated to the sand reservoirs overlying or underlying these shales: the second has been the demand for drilling fluids better adapted to penetrate these marine shales without difficulty and expense. Origin and General Composition of Clays and Shales Clays, shales and surface soils are all closely related materials. They are mixtures of finely divided compounds formed during the weathering of the solid crust of the earth. Their nature is essentially colloidal; that is, their behavior is determined by the state of division of the materials and the surface reactions of the smallest grains. Many of their chemical changes affect only the exposed areas and do not involve the interior of the grains of matter. The extent of these reactions is more nearly proportional to the area of the substances than to their mass, therefore it is possible for a small amount of a material in an extremely fine state of division to completely dominate the character of the mixture. More than 83 per cent of the crust of the earth is composed of three elements—oxygen, silicon and aluminum. Consequently, the corrosion products of the crust are predominantly aluminosilicates, or compounds of aluminum, silicon and oxygen. If we add the compounds of six elements—iron, calcium, sodium, potassium, magnesium and hydrogen—more than 98 per cent of the crust has been accounted for. These six elements, together with the first three, also appear in soils, clays and shales. But direct chemical analysis is of little value in describing the nature of such materials. Many chemical individuals may be present in variable amounts, and the extreme subdivision of any one of the individuals may contribute qualities that dominate the mixture.

Jan 1, 1939