Search Documents

By John Chipman, K. C. McCutcheon

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or dounward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,' in 1925, analyzed the gases extracted from rimming, sernikilled and killed steel ingots and found that the chief constituent of the rimmining gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune² reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By F. P. Peterson

The manufacture of gasoline by extraction or precipitation from the natural gases in which it is found, the present status of the industry, its past development and future extensions, offer a subject which is so broad that to handle it in its entirety would require a voluminous paper. The writer will, therefore, attempt to concentrate the essential matter of the subject for a general presentation, giving some of the most interesting details of the factors that are important to the industry. This industry has drawn liberally on the principles of physics and chemistry, and, to a large extent, has had to adapt such information as is most useful—not from data recorded with reference to petroleum, but from data recorded with reference to general treatment of other materials. Because of the complex character of the petroleum series of hydrocarbons and the fact that data, such as solubilities, 'vapor pressures, etc., . of the different petroleum compounds have not been determined, we are still working by rule of thumb in some essential phases of the industry. Furthermore, the difficulties of determining such data are almost insurmountable. We have not one, but two butanes to deal with—not one, but several, pentanes, hexanes, heptanes, and, as we ascend in the series the complexity and multiplication of isomers increases at such a rate as to make the task of isolating and studying their physical characteristics almost beyond the hope of possible attainment. The industry is the connecting link knitting the interests of oil producers and refiners into a much closer relationship than ever existed prior to its inception and development. The relation between the producer and the refiner of petroleum prior to 1910 was a rather antagonistic one in a commercial sense. It was to the interest of the producer of crude petroleum to sell it for a maximum consideration; the refiner's interest was to obtain the same product for a minimum consideration; therefore, each side of the business transaction retained within his own hands as far as possible the trade secrets of his business. Each side maintained an attitude of cold-blooded business sympathy only for the other. Cas-

Jan 1, 1918

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By W. A. Scheuch, J. Walter

Ordinarily secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered'metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must, just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product. Secondary Copper Used for Wire Bars Only clean secondary copper of the grades known to the trade as Numbers 1 and 2 are melted for wire-bar manufacture. This material, supplemented by that obtained from various manufacturing processes

Jan 1, 1930

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

In our sessions devoted to geophysical prospecting, the greater part of the time heretofore has been given to the presentation of theoretical subjects or highly technical details by specialists directly engaged in the development and perfection of the various methods. This was necessarily so, for we wanted such information available for the benefit of other workers and for our members who were anxious to gain a reliable understanding of the principles involved, to enable them to form an opinion of the adaptability of this new technique to their special problems. The methods have now been actively applied by many reliable organizations for several years and in this period there has been opportunity for operating mining men, engineers and geologists to appraise them. We therefore felt that it would be desirable at this meeting to give some time to interchange of opinion concerning results from actual cases. Consequently, the Committee on Geophysical Methods of Pros pecting sent out letters of inquiry to numerous mining people, asking for frank statements of opinion based on results from geophysical surveys at their properties. We have received many replies, among which 30 or more are of specific interest. On the whole, the point of view is remarkably uniform. Except for one or two who were, perhaps, a bit irritated, the operating men who have replied consider the methods to be capable of yielding valuable information when suitable conditions exist. Their attitude is definitely one of tolerance and of confidence in the integrity and sincerity of the outstanding workers. There is, however, a very general feeling that the chances of attaining positive and trustworthy results are small unless the work is directed by, or at least carried on with the close cooperation of, a geologist or mining man who is thoroughly familiar with the local geologic and mineralogic conditions and with the relations of the orebodies to rocks and structure. From certain comments, I am inclined to think that some operators are not greatly impressed with the cheapness of the work. Probably they are not attaching much weight to cost per acre, but are thinking primarily of total cost in terms of significant results obtained. It is

Jan 1, 1932

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

By Jerry H. Service, F. L. Partlo

The following investigation was undertaken to develop a method for determining with reasonable accuracy the depth of overburdens of 100 ft. or less. Seismic methods seemed to offer good possibilities. The problem differed from that of the familiar salt-dome location in that the depth of overburden to be determined is much less than is encountered in oil prospecting. This means that a much shorter time interval must be measured with accuracy. Refraction methods seem at present to offer greater possibilities than reflection. The air sound persists for from 0.1 to 0.5 sec., because of echoes, and seismic reflections coming during this time are difficult to detect. A seismometer sensitive to vertical vibrations only offers possibilities and has been used here with some success. It is hoped that the application of this type of seismometer to reflection shooting in this region may be investigated still further. The apparatus used consisted of a carbon-button seismometer followed by a three-stage, transformer-coupled, vacuum-tube amplifier and a General Radio string oscillograph. Time marks are provided by a 1000-cycle, 600-r.p.m., synchronous motor provided with five spokes which intercept the light to the camera at 1/50 sec. intervals. This motor is driven by a two-stage vacuum-tube amplifier of 3 watt output, actuated by a tuning fork. The power supply for the seismometer amplifier is one 2-volt storage and one 45-volt B battery. The motor amplifier is powered by a 6-volt storage battery and 6 to 225-volt, 15-watt motor generator. The temperature-frequency characteristics of the tuning fork have been determined and for ordinary working temperatures the error in time that would be introduced is less than M millisecond for time intervals up to 100 milliseconds. The impact is produced by a sledge blow for surface distances less than 100 ft. and dynamite for greater distances. Two steel balls with wires attached form an electric circuit through a 1-ft. piece of railroad rail upon which they rest. When the rail is struck by the sledge the balls rebound, opening the circuit and indicating the time of impact by a break in the oscillograph record line as at A, Fig. 3. When dynamite

Jan 1, 1934

By Edward Adarns Richardson

As developed up to the end of the Great War, an airplane was essentially a mechanism of wood and fabric, joined and held together by metal fittings and fastening. The engine and accessories, wire for wheel spokes and other tension members, and the occasional use of metal for inter-plane struts and the shafts of surface controls required some metal, but essentially it was a wood and fabric structure. Attempts had been made to use metal for other purposes, such as struts in the drag-trussing of wing panels and for short interplane struts, and Junkers had produced an airplane of iron in 1915. By 1917 he was using steel tubes and duralumin sheets, securing noteworthy advantages aerodynamically and from the standpoint of weight and upkeep. He was a pioneer along lines in which progress is still being made. Principles of Airplane Construction The loaded weight of airplanes ranges from 500 lb. for the light plane of which we heard so much a short time ago, to about 40,000 Ib. The great majority of planes range from 2000 to 10,000 Ib. Of this weight from 15 to 30 per cent. is for the dividend-earning load. This percentage is so low that every per cent. saved on the rest of the weight increases the pay load from 3 to 6 per cent,. The economic value of every pound that can be saved in designing or constructing a plane is sufficiently great to warrant spending money on refined methods of structural analysis, materials of superior strength properties for a given weight, methods of manufacture which may make possible the use of refinements in structural design, and the like, to an extent unknown heretofore. The weight of the airplane, without fuel, oil and crew, and pay load, ranges from 50 to 65 per cent. of the total weight loaded for planes suitable for commercial use. It is doubtful if the structural weight will ever be brought down to as low as 40 per cent. for commercial planes. The airplane may be roughly divided into: (1) Power plant, which includes engines, radiators, cooling water, oil and fuel tanks, piping, propellers, engine-starting systems, pumps, super-

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6&apos; ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By E. F. Kern, W. W. Loo

A review of the literature on the reduction of cassiterite showed that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world&apos;s consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue. The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents. Review of Literature Experiments on the smelting of Bolivian tin concentrates were made by James P. Gill in 1920 in the metallurgical laboratory of the School of Mines, and submitted as a graduate thesis. The results of these tests are fully reported as they are preliminary to the experimental part of this paper, and also because they have not been published. The variables investigated by Mr. Gill were: (a) the effect of temperature on the rate of reduction of cassiterite concentrates; (b) the time required for

Jan 1, 1928

By Paul M. Tyler

MINOR industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz (Iceland spar, tourmaline, fluorite, selenite, mica), and nonfuel gases (air, helium, carbon dioxide). ALUM MINERALS The alums comprise a series of double sulphates (or selenates) isomorphous with potash alum, which, according to a ruling of the Pennsylvania courts, is the only product commercially described simply as "alum." Common alum occurs in nature as kalinite (K2SO4- A12 (SO4) 324H2O). The mineral mendozite (Na2S04) 3.A12 (SO4)3- 24H2O) is soda alum; tschennigite (NH4)2SO4.Al2 (SO4)3.24H2O) is ammonium alum; and there are about a dozen other native alums and related double sulphates. Alunite (alumstone or alum rock) has the formula Al2(SO4) 3.K2S04.4A1 (OH)3 and alunogen, Al2(So4) 3.18H20. Saline residues, found wherever natural water is evaporated, may contain sulphate of alumina, which for most uses is the essential ingredient of alum. Mineral wells and springs that emerge from beds of pyritiferous shale are typically astringent and at times form local deposits of alum, generally as incrustations. Acid waters acting upon aluminous rocks may form sulphates of alumina. The alums of commerce, as well as aluminum sulphate (concentrated alum), are produced principally by treating bauxite with acid, but they have been made also on a substantial scale from clay, cryolite, pyritic slates, schists, lignites, alunite, and leucite. Alum shale-chiefly clay, pyrite, and (usually) carbonaceous matter-was extensively used in England as a source of alum for more than two centuries. In France, pyritic lignites mixed with sand and clay were burned in heaps to red ash, the leach Liquors from which, after treatment with ammonia, yielded alum and copperas. Processes have been developed for making alum or aluminum sulphate from such diverse materials as feldspar, aluminous phosphate minerals, greensand, and mixtures of mica and

Jan 1, 1949

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By M. H. Loveman

THE orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6&apos;, longitude E 97°20&apos;, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Symes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 annually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 12, 1916

By M. H. Loveman

The orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6&apos;, longitude E 97°201, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Syrnes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 anually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The . closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 1, 1917

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923