Search Documents

By L. G. Austin, P. T. Luckie, R. R. Klimpel

Application of the Charles and Bond Laws to batch grinding can be deduced as a special case of solution of the first-order batch grinding equation. With additional limitations on the feed size distribution, this special case also gives Rosin-Rammler distributions of constant slope, with the 36.79% retained point a simple function of time. In general, the assumptions concerning the breakage parameters S and B which are necessary to get Charles' and Bond's laws, are not valid except as a crude approximation. With less restrictive assumptions, it is still possible to get approximate Rosin-Rammler distributions, but the slopes change with time of grinding, and the 36.79% retained point is a more complicated function of time. An alternative form to Charles' law is suggested, which accomplishes the same result and has the same errors, but avoids the use of energy of grinding and deals with specific rate of grinding.

Jan 1, 1973

By J. C. Osler

The design of a tailings dam is a geotechnical engineering project of considerable scope. For the design, it is necessary to establish the engineering properties of the soil or rock strata which will support the dam and the tailings or other fill which will be used to construct the dam. The various field and laboratory investigations which are necessary to obtain the required design parameters are discussed in the paper and the use of these parameters to compute stability, settlement, and seepage are considered. The designer of a tailings dam can never assume an absolute knowledge of the properties of the foundation strata. Further, initial design assumptions are often approximate, particularly with regard to the distribution of pore pressures through and beneath the dam. Thus, the installation of performance monitoring instruments is recommended, since data obtained from such instrumentation can be used to check the stability of the structure both during construction and after its completion.

Jan 1, 1972

By L. Bruce McRae

A programme of work was initiated so that the possibility for the agglomeration of Transvaal chromite-fines by pelletization could be investigated. The use of cementitious binders did not yield promising results, binder additions of up to 10 per cent failing to produce an agglomerate that would be suitable as feed for an electric-smelting furnace. Further laboratory and pilot-plant studies showed that high-quality pellets could be made from chromite bonded with small amounts of bentonite and hardened by heat treatment at temperatures of the order of 1000°C. An investigation was also done into the reduction behaviour of pellets containing amounts of stoichiometric carbon up to that required for complete reduction. The results showed that the maximum degree of reduction that could be obtained was approximately 75 per cent, and that these pellets had the physical properties that would make them amenable to smelting in a submerged-arc electric-smelting furnace.

Jan 1, 1977

By W. W. Wen, S. C. Sun

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an amine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electro-kinetic behavior of coals of different rank and degree of oxidation were studied by an electro-phoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite is depressed. Comparing the flotation results with the electokinetic results verified that in the presence of ferrous sulfate, the maximum hydro-phobicity of oxidized coal with dodecylamine and frother is near its IEP, which is around pH 6.5 to 7.0.

Jan 1, 1978

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By D. J. MacKinnon, J. M. Brannen

Smooth, compact, dendrite free 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartments containing DSA anodes separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air sparging. The catholyte passed through the diaphragms into the anode compartments from which chlorine gas and spent anolyte were withdrawn. Standard electrolysis conditions were: 15 g/L Zn, 0.12 M HCI, I5 mg/L tetrabutylammonium chloride (TBACI) as the addition agent, 35°C, and 323 A/m2 (30 ASF) current density. The effect of variations in these conditions on the morpohology orientation, current efficiency, and energy requirement for 24-h zinc deposits was determined. The effect of total chloride ion concentration on the zinc deposit was studied by adding various amounts of NaCl to the electrolyte.

Jan 1, 1983

By Patrick M. Hurley

The relationships between mineral deposits and various plate margin mechanisms are examined under the constraints of radiogenic isotopes and other geochemical indicators. It seems like1 y that: (1) deposits of the spreading ridge association are fairly ubiquitious through most of geologic history and can be recognized by the lithologic assemblage and primitive lead isotope ratios; (2) most metals in the island arc association are not derived entirely from a subducting oceanic plate, and have a partly continental affinity; (3) subduction beneath a continental plate generates ores which are derived either from the downgoing plate or from the lower crust; (4) the heating of a continental plate by thickening or by mantle plumes may develop a metallogenic province involving extraction of metals from the curst; (5) rifts and grabens developing thick sections of marine sediments with evaporites may be the locus of base metal mineralization by movement of reducing brine solutions resulting from diagenesis and bacterial reduction of sulfates

Jan 1, 1978

By G. S. Ansell

RCENTLY, in investigating the high-temperature creep properties of an aluminum, SAP-type alloy, MD 2100, fabricated by Professor F. V. Lenel of Rensselaer Polytechnic Institute, Ansell and Weertman1 found unusually low creep rates. These creep rates are 4 or 5 orders of magnitude lower than is predicted by the slowest creep mechanism based upon dispersion-hardened alloy theory. They ascribed these results to a lack of both normal active dislocation sources and a continuous three-dimensional dislocation network. If one couples these results with the following factors of production and microstructure: 1) The compacted and sintered aluminum powder compact is hot-extruded, with an extrusion ratio of 25:1.2 2) The alyminum oxide particles are approximately 140A units thick, and have a spacing varying from 0.05 to 1.5 1. 3 3) The alloy has plate-shaped grains with minor axes of about 5 X 10 -3 mm and major axes several orders of magnitude greater than this.'

Jan 1, 1960

By A. H. Roberson, L. H. Banning

DURING the past few years, a considerable tonnage of ilmenite has been produced as a byproduct of a monazite dredging operation and stockpiled near Boise, Idaho. This ilmenite has not been marketed because of the long distance from ilmenite-consuming areas and its comparatively low TiO2 content. Production of monazite from the alluvial sand deposits of Idaho is a mar- ginal venture when it is the only marketable product, and it will be necessary to establish a byproduct market before the operation becomes economically stable. Early in 1954, the Bureau of Mines Northwest Electrodevelopment Laboratory at Albany, Ore., conducted a series of tests which demonstrated that arc furnace smelting could be utilized to produce commercial quality pig iron and a high titanium content slag from these ilmenites. Additional studies showed that the slag chlorinated readily to produce a satisfactory yield of TiCl4. The investigation was carried out by two research teams. The Ferrous Metals Branch, with adequate

Jan 1, 1956

By K. Thirumalai

Rock response to heating depends on properties of rock material and varies widely between different rock types. By dissipating energy, surface melting limits rapid heating and fragmentation of rocks achieved by surface heating methods. This study advances a concept of rock fragmentation by rapid internal heating of a localized inner volume of rock. The working of the method to achieve fragmentation of rocks (Charcoal granite and Dresser basalt) having poor response to surface heating is analyzed. Experimental data on elevated temperature rock properties required for the study are presented. Based on the properties of test rocks, a high frequency (50 MHz) dielectric heating method of generating localized internal heating was selected for experimental study. The test rocks were fragmented without melting under localized heating below 600ºC. The heated volume required for fragmentation was observed to be less than 2 percent of the test block volume. A practical application of the method for in situ fragmentation of rocks is suggested.

Jan 1, 1971

By Gordon M. Matheson, Charles V. Logie

The current state-of-the-art design of mine pillars can be grouped into empirical and numerical design techniques. Numerical design techniques are based on sophisticated computational techniques which analyze the stresses and strains through the interstices of a pillar. Empirical techniques are less exact, but have been widely used, particularly for coal mine pillar design, because of their ease of computation. Over the years numerous empirical equations have been proposed to calculate the ultimate strength of coal mine pillars. This paper presents a review of the various equations which are most frequently utilized and examines the fundamental assumptions, limitations and applicability of the design formulae. The review intends to provide the practicing mining engineer with an understanding of the assumptions and mathematical basis of each equation to aid in the selection of the criteria most applicable to his specific design problems. Recommendations are made of the empirical equations that are presently most acceptable for design.

Jan 1, 1983

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By G. B. Gibbs

Various semiempirical equations which relate defect-formation energies and entropies with elastic and thermal properties of a metal crystal are shown to be related by a simple model for lattice energy. An illustrative comparison of theory with experiment is made using self-diffilsion data for fee metals. SEVERAL workers have related the free energy of defect formation with elastic and thermal properties of a crystal lattice, particularly elastic bulk modulus and Debye temperature. The present note shows how the various approaches are related by a simple model for lattice energy. A comparison of theory with experiment is given using the self-diffusion parameters of fee metals. 1) A MODEL OF THE CRYSTAL LATTICE The internal energy per atom in a metallic lattice may be written U=Ui-Ue [1] where Ui and Ue refer to ion-ion interaction and valence electron energies, respectively. The volume per atom V has an equilibrium value 52 for which

Jan 1, 1968

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1983

By R. F. Shurtz

This paper relates geostatistical doctrine to classical statistical and mathematical concepts. It is not a contribution to geostatistics; it is a contribution about geostatistics. It uses descriptive and pictorial arguments to assist interested readers in forming an intuitive grasp of the recondite and difficult mathematical issues involved. The method chosen is to cite authoritative literature references from the two fields and trace connections between them. Four broad conclusions appear: first, geostatistics comprises a relabelled subset of concepts detached from classical statistics and mathematics; second, this relabelling artificially isolates geostatistics from the classical fields and restricts its scope; third, the classical fields still have much to offer to the mining industry but will remain fallow unless artifcial communication barriers are removed; and fourth, the unique advantages asserted for geostatistics are neither unique nor necessarily real. These findings should not be regarded as iconoclastic but rather as Pointing the way to a wider and more productive scope for those who evaluate mineral deposits.

Jan 1, 1983

By E. J. Schmitz

The following abstract of an unpublished treatise, prepared by me, on the geological formations and minerals of the State of Alabama, is deemed of interest to the Institute. This State, called after the river of the same name (which, formed by the junction of the Coosa and the Tallapoosa, waters, with its tributaries, more than half the State), is divided by its main watershed into a larger southern district, sloping south and southwest, and drained into the Gulf of Mexico, and a smaller northern district, sloping generally north and west, and drained into the Tennessee. Geologically the State may be divided (according to historical geology) according to the different formations it exhibits, among which I include the Azoic, the existence of which in Alabama has been doubted by some; or it may be divided (according to structural geology, as closely related to topography) into a north and northwestern, a middle, and a southern zone.

Jan 1, 1884

To THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN Like every other significant activity in the United States today, the work of the Institute has been affected by and adjusted to the prosecution of war against Germany, .Japan and their satellites. As the elaborate engines and materiel of modern mobile warfare are made, for the most part, of metals and other minerals; and are powered by mineral fuels, the industries -represented by the A.I.M.E. are of primary and vital importance. Of some 29 critical materials officially listed by the War Production Board, 24 are minerals. An alternate for one of the others, rated as a nonmineral, is to be made principally from petroleum. This alludes, of course, to rubber. The procurement of tremendous quantities of such raw materials and the effective processing, fabrication, and utilization of them depend on members of those branches of the engineering profession represented by the A.I.M.E.

Jan 1, 1943