Search Documents

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal ('junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill' and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows: The Robert W. Hunt Medal and- Prize, The J. E. Johnson, Jr., Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert. W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best on al paper or papers on iron and steel. The scope of the term "iron and steel" shall determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. J. E. JOHNSON, JR., AWARD This award is made from' the income of a. fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers. to the Institute's Transactions. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control of the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made the following regulations concerning it:

Jan 1, 1925

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal and Prize, The J. E: Johnson, Jr. Award, The Lewisohn Platinum Prize to senior members, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to' establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term" iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition. of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be ,designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's Transactions. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control of the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made 'the following regulations concerning it:

Jan 1, 1925

By M. R. Campbell

Coal is the geological product of entombed vegetal tissues. This view of its origin led Stopes and Wheeler to define it as "mummified plants." They evidently intended this term to be used in a broad way and to mean the preservation of the organic material, as such, regardless of the means employed to accomplish the purpose. The term " coal" should be regarded, therrfore, as broadly generic, and applicable to all accumulations of vegetal tissues as soon as they are covered and protected either by water or by earthy material. In this sense peat should be regarded as the first stage of coal formation and the term coal should include the resultant products of transformation in all other stages of the process until they have lost all resemblance to the original matter from which they were derived. If this idea of the development of coal is accepted and it is admitted, as the geologists claim, that the forces which produced this transformation of the coal have been active since vegetation began to grow upon the land, and are still in operation, it is obvious that somewhere in the world there are all gradations of this material from peat just forming in the swamps of today to graphitic anthracite which presumably marks the most advanced stage that can be recognized with certainty as belonging to the series. Some of these coals, particularly those occurring in the upper part of the series, are fairly well known because they are the ones that are most widely distributed and have been mined and utilized most extensively. On the other hand, the coals in the lower part of the series are but little known because they are not so abundant and, owing to their relative inefficiency, have been only slightly exploited and utilized, especially in regions where the better coals are abundant. The result of these conditions is that much research work has been done on coals of the higher ranks and a great body of facts regarding their physical and chemical properties and the uses to which they are best adapted has been accumulated, but little information is available regarding the coals of the lower ranks. Many able scientists, particularly chemists, have attempted to bring some order of the chaos of coals of various compositions and uses by

Jan 1, 1930

By Arthur F. Taggart

Tins paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. CAPACITY Operators know that the tonnage of rock that can be put through a particular crusher in a give time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: TR = TR80KK'K" [I] in which Ts, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R80 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific gravity range - 2.5 to 2.7 - T should. be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppard1 has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about 1.5 : 1 : 0.6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:0.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for 150 + 200-mesh pyrite to be 1.4: 1 : 0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value 1.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciable tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 80 per cent of the feed, divided by the aperture that would pass 80 per cent of the product. It is best determined from screen tests.

Jan 1, 1941

By Arthur F. Taggart

THIS paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. CAPACITY Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: TR = TR80KK'K" [I] in which TR, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R50 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range-2.5 to 2.7-T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppard' has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about I.5: I: 0.6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:0.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for -150 + 200-mesh pyrite to be I.4: I : 0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value I.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciable tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 8o per cent of the feed, divided by the aperture that would pass S0 per cent of the product. It is best determined from screen tests.

Jan 1, 1941

By C. A. Stickels, C. M. Yen

Secondary recrystallization was investigated in vacuum-melted electrolytic iron to which 70 pm N was vacuum-meltedadded. The secondary texture is "near {554}<225>" for material cold-rolled 75 to 90 pct, the sharpness of the texture increasing with increased rolling reduction and with decreased annealing temperature. At reductions of 95 and 97.5 pct the secondary texture is &apos;"near {322)(296)". Both secondary orientations also exist as major components of the primary re-crystallization texture. Development of a strong "near {554) (225)" secondary texture appears to depend on the evolution of the Primary texture to a transition texture depleted in orientations near the secondary orientation before the onset of secondary growth. A variety of qualitative experinzents have been used to show that nitrogen is important in limiling primary grain growth. The presence of nitrogen does not seem essential for the establishment of a transition texture, but a loss of nitrogen during annealing may facilitate growth of grains in the secondary orientation. Secondary grains we shown to form initially at the specimen surface. This is not thought to indicate that surface energies are important in the growth process. It is proposed that the quasi-two-dimensional character of surface grains permits discontinuous growth parallel to the surface before secondary growth of interior grains is possible. An earlier study of recrystallization textures in 90 pct cold-rolled electrolytic iron showed that secondary recrystallization occurred after annealing for several days at 700C1 This type of secondary recrystallization, which had not been reported previously, results in the formation of a strong texture, best described by the indices "near {554}(225)". The purpose of the present work was to investigate the effect of various processing variables on secondary recrystallization in this material and determine the mechanism of secondary grain growth. LITERATURE REVIEW An understanding of the mechanism of a secondary recrystallization process depends on knowing: 1) how grains in the secondary orientation come to be in the primary recrystallization texture; 2) why normal grain growth does not occur; and 3) what factors determine the strength of the secondary texture. For secondary growth of grains of a particular orientation, a certain minimum fraction of the grains must be in that orientation after primary recrystallization. This requirement is apparently satisfied "naturally" in certain systems, i.e., when the primary texture obtained by rolling and recrystallizing material initially randomly oriented contains a sufficient fraction of primaries in the secondary orientation. However, in other cases, e.g., {110}<001> and {100}<001> secondary growth in silicon iron,2 it is necessary to enhance the fraction of primary grains in the secondary orientation by rolling and recrystallizing textured material. In the present case, the "near {554}<225>" orientation is contained within the spread of orientations found in the primary recrystallization texture of iron or bbc iron-base alloys. In systems where the main driving force for secondary growth is the reduction in total grain boundary energy, secondary growth is observed only when normal grain growth is minimized. Four ways in which normal grain growth can be limited are: 1) Limitation by a strong primary texture. When a very strong primary texture consisting of a single component or twin-related components develop, most primary grains are separated from one another by relatively immobile small-angle grain boundaries. The classic instance of this is secondary growth into the primary cube texture in some fcc metals. 2) Limitation by precipitates. Precipitates present in the proper volume fraction with a suitable dispersion will limit primary grain growth. The role of MnS inclusions in impeding normal grain growth in Si-Fe is well-documented.5 3) Limitation by sheet thickness. Normal grain growth slows drastically when the mean grain diameter is of the same order as the sheet thickness. This effect has been used to obtain secondary recrystallization in thin sheets of high-purity silicon iron.&apos; 4) Limitation by solute impurities. It is well-established that certain impurity elements in solution can have a large effect on grain boundary mobility.&apos; However, there does not seem to be any secondary recrystallization process in which primary grain size stabilization has been shown to be due to the drag exerted on grain boundaries by dissolved impurities. In certain systems, e.g., secondary recrystallization in silver,&apos; the means by which normal grain growth is limited has not been identified, and solute-impurity limitation might be suspected. In order to understand the factors which determine secondary texture strength in three-dimensional growth, it is necessary to examine in more detail the current picture of general secondary recrystallization processes. Following Cahn,9 it is assumed that the primary grains have a range of sizes and that secondary growth of one of the large grains in this distribution is possible when it exceeds a critical size with respect to its neighboring grains. The critical size depends on the ratio ?S/?p, where ?s is some sort of average grain boundary energy between the potential secondary and the primary grains and ?p is some sort of average grain boundary energy between primary grains. For a constant primary grain size, the critical size for secondary growth increases as ?$/?p increases. May and Turnbull5 have incorporated the

Jan 1, 1969

The engineering personnel shortage, present and impending, so well brought out in the article in Mining Engineering in the August, 1951 number, both in the editorial lead and the article by William B. Plank and Henry J. Petrie, has left untapped and has ignored a potential source of supply that would fill the need ably and with complete satisfaction. This source is comprised of the women engineers- and geologists, both presently, trained and able to handle work at all levels, and the many who would make splendid engineers and geologists if they could hope for even a modest taste of the square deal that should be theirs, but, as we all know, is not. I write from experience. It is not pleasant or sensible to have to urge borderline cases among men students to consider engineering and geology as careers to fill the need, when I have far more able, interested and suited young women students whom I must divert into other channels. It does not make sense to scrape the bottom and sides of the barrel to induce potentially second or third rate male engineers and geologists to enter the profession when we have superior material among the women, eager to do good work in these fields. It does not make sense for these men to become second or third rate in these fields when they might be first rate salesmen, musicians, advertising copywriters or policemen. Nor does it make any more sense to force potentially first rate female geologists and engineers to become second or third rate and very frustrated typists, kindergarten teachers, dress sales-women or clerks. At this point I am willing to admit that where superstitious -miners object to women in underground workings, men are available for the jobs. Moreover, it is not necessary for women to be sent into the most difficult country, if there is reluctance on either side of the contract. There may be fewer of them eager for the roughest assignments, in proportion to the men, but women are so accustomed to discrimination far more complete than that against any racial or religious group, that a reasonably tough assignment would seem like a heaven-descended joy. In my own experience, I have found that my girl students majoring in geology, could keep up with me in the field in the roughest terrain, but. the men, all but the best students and the most physically fit young men, complained that they could not keep up with me and that I always "walked their-legs off. The women, a few men and I always returned with bags heavy with well chosen specimens and proper notes. Most of the men carried no specimens and-but poor scraps of notes on loose bits of paper. Yet the men were urged to prepare for a career in engineering or geology if their examination marks were reasonably good. When we find that we still have a shortage of engineers and geologists, after putting all the qualified women to work, then we may begin to worry. Until then, we are simply fooling ourselves as we wander in, a forest of outmoded tradition and emotional habit reactions. MARY W. GARRETSON ASSOC. MEMBER, AIME SCARSDALE, N. Y.

Jan 1, 1952

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Guillermo V. Borquez

INTRODUCTION The basic factors that influence the selection of a mining method are the geometry of the ore deposit and the strength of the ore and surrounding rock. These factors usually determine the ore recovery and dilution of the deposit under analysis. For the purpose of this paper we will consider a generalized case of a block caving system and the sequence of the analysis needed to optimize ore recovery. The analysis presented is intended for the preliminary planning stage. The critical factors involved in the caving process are identified and the methods for evaluating the suitability of a particular deposit to the caving method of mining are outlined. The mine design is approached by identifying the two most important, dimensions: the size and spacing of the draw points. These dimensions are estimated from a simulation model which takes into account the ore recovery, the incremental value of the ore recovered, and the safety conditions of the operations. The model estimates the number of draw points required to extract efficiently and safely the broken ore from the caving area. This number is found in the range where the net incremental value of the ore is maximized and the probability of pillar failure does not exceed the limit which is acceptable for a safe mining operation. A mining method and its design are in a continuous process of optimization. This process is unique for each deposit because of the many parameters involved; therefore, a back analysis of the operations should be performed when possible. These analyses will indicate if the ore body responds in a predictable manner to the parameters contained in the geological, fragmentation, and draw point models. SELECTION OF ALTERNATIVE MINING METHODS The selection of a mining method best suited to define the minable ore reserves of a given deposit involves consideration of the geometry of the ore deposit and the strength of the ore and surrounding rock. These two factors are usually sufficient to determine the ore recovery and dilution of the deposit. After analyzing the geological reserves and defining the limits of the deposit, either an open pit or an underground mining method can be selected to define the minable ore reserves. The sequence of steps to follow in the selection of a mining method is presented in Figure I. From an economic point of view, the strip- ping ratio is the determining factor for the selection between an underground or open pit method. In turn, the stripping ratio is a function of the grade distribution and con- figuration of the ore body. In order to obtain a preliminary estimation of the stripping ratio, a parametric analysis could be applied, such as the approach used by Professor E. P. Pfleider (1972) and summarized in Table 1.

Jan 1, 1981

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years&apos; service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

By H. A. Doerner, F. D. DeVaney, J.B. Clemmer

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By J. B. Austin, R. L. Rickett

MEASUREMENTS Of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even interpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By Linn Bradley, W. W. Strong, H. D. Egbert

A hot-dry method of cleaning the gas from blast furnaces has been shown1 to conserve the sensible heat energy of the gas, and in general it thus permits of a higher flame temperature. The electrical method of cleaning gases removes from 98 to 99 per cent. of the suspended matter in one operation when operating properly, thus making possible the use of a very clean gas for burning in the stoves. The use of such clean gas thus makes feasible a different type of hot-blast stove construction from that being used at present. It therefore seems advisable to construct the stoves from the viewpoint of getting the maximum amount of heat energy into the products of combustion. By preheating the air added to the top gas and obtaining a better mixture of the air and top gas, less excess air will be required and a higher flame temperature obtained from the combustion of the top gas. The interior of the stove should be provided with a kind of brick that will withstand a high flame temperature, will conduct the heat energy along certain directions, insulate the flow of heat along other directions and at the same time store heat energy so as to make the flow of such energy more uniform. It is quite likely that these results can be best obtained by using several kinds of bricks: one type which is a good insulator of heat energy to be used for lining the stove and for making partitions through the stove to restrain the flow of heat; another type of brick or material with high refractory qualities; and a third type which will be a good conductor of heat energy. The surface of the stove exposed to the atmosphere should be a minimum in comparison to the mass of checkerwork which it is possible to obtain, due regard being paid to other conditions. With clean and hot furnace top gas it will be advisable to consider a rearrangement of the checker work in the stoves. One season for the present size and shape of checker openings is to provide facility for

Jan 1, 1917