Search Documents

By L. L. Handy

The development of a theory for miscible liquid displacement requires evaluation of the variables which affect growth of the mixing zone between solvent and displaced oil. Factors which appear to be important are individual fluid viscosities, viscosity ratios, flood rate, fluid densities, flow characteristics of the porous medium and molecular diffusion coefficients of the fluid components. The primary purpose of this paper is to evaluate diffusion effects. Theoretical treatments to date have been limited to floods for which the viscosity ratio is one. Two principal theories have been proposed. Von Rosenberg adapted for porous media a theory derived for capillary tubes by G. Taylor.' ,' In this theory molecular diffusion perpendicular to the direction of flow is a primary factor in sharpening the flood front. Slow floods give sharper fronts for a given distance traveled than fast floods. An alternative theory considers miscible liquid displacement as a statistical problem.3,4,5 Diffusion is not an important factor in this theory, but it leads to the same general type of equation as von Rosenberg's. Both theories predict S-shaped concentration profiles with the same dependence on distance traveled. The statistical or "dispersion" theory predicts rate independence, however. To supplement rate studies a direct measurement of a diffusion effect would be helpful in evaluating which of the two proposed mechanisms best describes miscible liquid displacement for one-to-one viscosity ratio systems. No quantitative theory has been proposed for floods in which a low-viscosity fluid displaces a high-viscosity fluid. It might be anticipated, however, that the extensive fingering observed in floods with adverse viscosity ratios would increase opportunities for an exchange of components between displaced and displacing liquids by a diffusional process. Even if molecular diffusion were not an important mixing mechanism for one-to-one viscosity ratio systems, it could be significant in systems with adverse viscosity ratios. METHOD FOR EVALUATING DIFFUSIONAL MIXING In solvent flooding the displacing liquid can become mixed with the displaced liquid by a number of processes; in general, either mechanical or diffusional in character. To evaluate the contribution of diffusion, a method was sought that would distinguish diffusional mixing from mechanical mixing. Suppose two soluble tracers are added to the displacing liquid and that one tracer has a diffusion coefficient much greater than the other. Then, if diffusion is important during miscible liquid displacement and if diffusional transport is primarily transverse to the direction of flow, substances with high diffusion coefficients will have sharper concentration profiles than those with comparatively low molecular diffusion coefficients. In order to have material balance the profiles for the two tracers must intersect. For one-to-one viscosity ratios the intersection would occur at the 50 per cent concentration point. It is generally assumed that diffusion in the direction of flow is negligible. This assumption appears reasonable because flow velocities are ordinarily orders of magnitude greater than diffusional velocities. If this is not a valid assumption, however, the shapes of the fronts will be further degraded by longitudinal diffusion. The effects of rate and molecular diffusion coefficients are the opposite for longitudinal diffusion to those for lateral diffusion. Higher rates or lower diffusion coefficients would tend to give sharper fronts. The double tracer method offers several unique advantages in evaluating effect of molecular diffusion. First, the method gives a direct measure of the effect of diffusion on mixing zone size. Second, the effect of a difference in diffusion coefficients is determined from a single experiment. Comparison of several experiments at different rates is not required. Third, the method is applicable for any viscosity ratio. Fourth, the method is unaffected by density differences between the two fluids which might result in rate dependent gravity effects. EXPERIMENTAL PROCEDURE Suitable tracers are substances whose diffusion coefficients differ as widely as possible, but whose adsorptions on rock surfaces is negligible. The two tracers selected were methanol and sucrose in water solutions. The approximate diffusion coefficients for methanol and sucrose, as given in the International Critical Tables, are 1.3 X 10-5 and 0.3 X 10-5 m2/sec, respectively. Concentrations in the water solutions were 200 gm/liter of solution for both methanol and sucrose. These high

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By D. Harker, M. J. Murphy

The mechanism by which age-hardening takes .place is still not completely understood. The principal theories range from the extreme of "precipitaiion-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. Preparation of Formvae. Replicas of Metallic Specimens This section is concerned with the techniques that have roved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. it is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work—very fine polishing and etching with very dilute solutions—is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. Preparation of Metallographic Specimens The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch—to approximately the depth necessary for a micrograph at 1000 diameters—usually produces a sur-

Jan 1, 1945

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By AIME AIME

THE Employment Bureau of the F. A: E. S., conducted under- the direct supervision of the secretaries of the four Founder Societies, has wanted to extend its activities and usefulness but it is operating right up to the limit of its budget; consequently, anything which requires the expenditure of more funds cannot be -undertaken, for the present. A great deal of time has been spent in recording, classifying, and interviewing the men listed, but owing to the business depression, only a comparatively small number of men have been placed' luring the last few months. There are men in New York from all over the country. What the Bureau needs is more positions available. With this in view, a number of high-grade engineers, themselves in need of employment, volunteered their services for a publicity campaign in the City of New York. A definite mode of procedure was evolved, and the success of the movement has been considerable, so much so that it has been thought well to call it to the attention, of members elsewhere, so that similar committees ' and campaigns might be organized in other cities. Following is a chronological arrangement of the methods used.

Jan 1, 1921

By John W. Weeton, Max Quatinetz, Robert J. Schafer

Nickel powders of 1-, 0.4-, and 0.2- average particle size were combined with 0.05- p MgO powder. Oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were vacuum hot pressed and extruded at 2100°F. In spite of a general tendency to growth of oxide particles during processing, dispersions of fineness comparable to those of Sintered Aluminum Powder, SAP, were achieved. A small amount of oxide considerably improved 1800°F stress-rupture strength, but further oxide addition resulted in a decrease of strength. RECENTLY there has been much speculation concerning the requisites for strong and stable dispersion-strengthened alloys. The nature of the dispersed phase, the stability of the alloys, and variables influencing the mechanical properties of alloys have been given consideration. Such topics have been reviewed by Bunshah and Goetzel. Of the many parameters related to the mechanical properties of dispersion alloys, mean free path between dispersed particles (a measure of the fineness of the dispersion), particle size, and vol pct of the dispersed phase have been shown to be very important. Generally, strength increases with decreasing mean free path, and there is an optimum vol pct of dispersed phase. Just how fine a dispersion ought to be is somewhat open to debate, but Irmann, Lenel, Backensto, and Rose, Gregory and Grant,4 and others have shown in the original SAP-type alloys, aluminum plus aluminum oxide alloys, that better strength is generally obtained with finer dispersions and the best strengths were obtained when the mean free path was less than . Further, Cremens, and rant' showed that in nickel plus aluminum oxide alloys, stress-rupture strength at 1500°F was definitely increasing with decreasing mean free path. In their investigation, however, the finest dispersions that were produced were about 2.0 mean free path. To determine the potential of the nickel plus oxide type of product, it would be neces- sary to obtain dispersions analogous to those of SAP alloys; namely, ones where the mean free path between oxides is less than . Unfortunately, however, it is very difficult to produce extremely fine dispersions of oxides in metals other than those which naturally form refractory oxide skins. There are several approaches to this problem including such procedures as mechanical mixing, internal oxidation, reduction of mixed oxides, and metal deposition from solution. Work at the Lewis Research Center has shown that metal powders 0.1p or finer could be produced by ball milling, when selected grinding aids were utilized.' Because these unusually fine powders were available, it was an initial objective of this study to determine if by mixing of these fine Ni powders with various amounts of MgO (0.05) a fine dispersion of MgO in Ni comparable to those in Al-Al203 might be achieved. A second objective was then to attempt to relate the parameters of structure to 1800°F stress-rupture strength of the alloys. Nickel powders of 1-, 0.4-, and 0.2-p average particle size were combined with 0.05- average particle size MgO powder. This oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were hot pressed and extruded at 2100°F.

Jan 1, 1962

By R. O. Williams

Analytical representation of the thermodynamics of solutions is highly desirable from the standpoint of accuracy, compactness, and numerical manipulations. In particular, computer calculations are greatly implemented. Mathematical considerations show that previous expressions have one or more serious defects. This investigation shows a Fourier series to be satisfactory but that it is also possible to derive a new series which fits certain additional conditions. Included examples show the value of analytical expressions in giving a simple characterization of each system using some two to five parameters, the elimination of the Gibbs-Duhem integration, and the es timation of the error for the experimental function as well as derived functions. It is further shown that the present characterization provides easy comparison between systems. IN the past, thermodynamic calculations have depended to a considerable extent on tabular and graphical methods. As the volume and precision of such data increase such methods become less satisfactory. Specifically, the selection of the optimum representation and the estimation of errors require statistical methods which in turn require analytical representation. The utilization of such data require further manipulations which are best done analytically for maximum precision. For example, phase equilibria are determined by common tangents to free-energy curves: a graphical determination is normally of low accuracy. As computers are increasingly used analytical representations become almost mandatory. Insufficient mathematical consideration has been given previously to the selection of empirical expressions. Those expressions having some theoretical justification are generally too inflexible and mathematically unattractive. We consider the problem in some detail and show that a Fourier series can be effectively used. Also a new series is defined which has certain advantages. ANALYSIS We wish to consider the analytical representation of the heat of mixing, AH, the excess free energy, ?Gxs, and the excess entropy, ?sXS, as a function of composition, X, for binary solutions relative to the pure components in the same state. When a distinction is not required, we use W to denote any one of the above functions. One may use a Taylor expansion around X = 0 to generate a power series. As the derivatives are un- known we represent the series as W = A + BX + CX2 + DX3 + EX4 + ... [l] where the constants A , B, C , ..- are to be selected to provide some optimum fit. For the extremes of composition W is necessarily zero so it follows that A = 0 [2a] B +C + D + E +••• = 0 [2b] Nonelectrolytes, which we are considering, appear to satisfy the condition that d3W/dx3 = 0 [3] in the terminal regions. This is the basis of the a, ß, and Q functions used by Hultgren et al.' and others. While this condition does not have a strong theoretical basis it does appear desirable that any analytical relation should satisfy this condition. Darken2 and Turk-dogan and Darken3 have shown that many systems exhibit this behavior over an extended range from each terminal region, departure being restricted to a limited intermediate region. Since we have no a priori knowledge as to where this transition occurs we can require that this condition be satisfied only as a limit at the extreme compositions as a general condition. We will show later how more restricted conditions can be included in specific solutions. Darken2 has called this behavior the quadratic formalism; we call our application the limiting quadratic formalism, LQF. This condition applied to the above power series requires that D = 0 [4a] 4-3-2E +5-4-3_F + 6 • 5 . 4G + ••• =0 [4b] The form of the power series normally used, due to Margules,4 is W=X(1-X)(A + BX + CX2 + DX3 + EX4 + •••) [5] where A, B, C, --. are a new set of constants. (Guggenheim5 has given a variation of this expression in a more desirable form. Since, however, it is contained in the above expression it does not require separate consideration.) This form is precisely what results by incorporating the conditions in Eq. [2] into the power series and regrouping the constants. The LQF requires that B =C [6a] and 4.3.2(D-C) +5-4-3(E-D) + ••• =0 [6b] Thus, the correct form of the Margules expression with two adjustable parameters is w =X(1-X)[A + B +X2-2/3x3)] 171 and the EX4 term must be included before three adjustable parameters are permitted.

Jan 1, 1970

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published' which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this- field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,16 Parry,180 Roe,153 and Parks.162 At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was 'organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J: M. Schopf, Devonian-Mississippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which, dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. Whitehead, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia .was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling, and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion 'was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl O.

Jan 1, 1952

By T. A. Wilson, S. L. Hoyt

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.' The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been done on single-crystal zinc, but as it is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips' have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1928

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972

By Charles M. Packer, Oleg D. Sherby, Roy H. Johnson

Originally round tensile specimens of a eutectic Zn-A1 alloy develop elliptical cross sections during superplastic deformation. This observation, coupled with a detailed study of the microstructure and preferred orieniation, suggests that crystallographic slip and continuous grain boundary migration or re-crystallization are important processes during super-plastic deformation. In spite of the extensive activity in superplasticity1-15 and the numerous explanations proposed, no single model has had universal acceptance. It has been established, however, that the general requirements for superplastic extension of two-phase alloys include an extremely fine, stabilized grain size of the order of a few microns, a temperature about equal to or greater than one-half the melting point, a critical range of strain rate, and a similarity in the mechanical strength of the major phases. The proposed models can perhaps best be characterized in terms of the important phenomena associated with them. These phenomena include: phase instability,1 diffusional creep by volume diffusion3 or grain boundary diffusion4,5 slip and continuous grain boundary migration or recrystalliza-tion,= grain boundary Sliding,7-9,13,14 and dislocation glide.'5 In this paper, experimental observations will be reported which support a model involving slip and continuous grain boundary migration or recrystalliza-tion. Specifically, a correlation will be made between this model and the development of elliptical cross sections as originally round specimens are superplas-tically deformed. For the most part, superplasticity studies have been conducted with eutectic or eutectoid alloys. Probably the most thoroughly studied material has been the monotectoid Zn-A1 alloy.1,2,6,12,13,15 No attention to the eutectic Zn-A1 alloy has previously been reported, and the results discussed in this paper represent part of a general study of the superplastic properties of this alloy. MATERIALS The alloys used in this investigation were prepared by melting appropriate quantities of 99.99+ pct A1 and 99.999 pct Zn in air, mixing, and pouring into a water- cooled stainless-steel mold. Wet-chemical analysis was conducted with each heat of alloy prepared, using the procedure of Fish and smith.16 The composition of the eutectic alloy was 95.1 wt pct Zn. Ingots about 2 in. thick were rolled to 0.4-in. plate at about 300°C with a reduction of 5 to 10 pct per pass. Specimens were machined from the plate with the tensile axis parallel to the rolling direction. The specimens were round, with 0.150-in.-diam, 1.25-in.-long gage length, and 0.25-in.-diam threaded grip sections. EXPERIMENTAL PROCEDURE Specimens were mounted inside a uniform-temperature quartz tube which was surrounded by a double elliptical radiant furnace with a 12-in.-long uniform-temperature hot zone and a low thermal capacity. The tube extended through the top and bottom of the furnace and permitted rapid quenching of the loaded specimens when quickly filled with cold water at the conclusion of the test. The quench precluded any effects on specimen microstructure from a normal, slow cool. Constant stress was applied to test specimens by suspending a load on a constant stress cam of the type described by Hopkin.17 The design of this cam permitted application of a constant stress for elongations up to 200 pct. For greater elongation, approximately constant stress conditions were maintained by systematically reducing the load manually. RESULTS As part of an investigation of the superplastic properties of the eutectic Zn-A1 alloy, evidence was obtained for the development of elliptically shaped cross sections as originally round specimens were extended. For example, after an elongation of about 100 pct, a round specimen with an initial diameter of 0.150 in. became elliptical with major and minor axis of 0.128 and 0.88 in., respectively. Photographs are presented to illustrate the ellipticity developed during superplastic deformation, Fig. 1. The specimen shown was deformed at a stress of 500 psi, at a temperature of 285°C, and a strain rate of 2.28 x 10-2 min-1. The strain-rate sensitivity exponent* was measured at *The strain-rate sensitivity exponent, m, is defined as d In o/d In c where o is the steady-state flow stress and E is the strain rate. this temperature and in the strain rate range 10"3 to 10-1 min-1 was found to be about 0.5. This value is typical of those observed with superplastic materials. The material studied exhibited negligible strain hardening during superplastic deformation, the creep rate remaining constant under constant stress and temper-

Jan 1, 1969

By J. W. Wolfe

The Benedict-Webb-Rmbin equation of state was used in digital computer programs to make rapid determinations of natural gas equilibrium phase compositions. Mixture components were the nine hydrocarbons, methane through heptane. Comparative tests were made with data from field separators, plant exchangers and literature sources. For most tests made, the B-W-R equations predrcted component K-vallles, mixture enthalpies and phase aensities within tile accuracy of available correlations for rune-component mixtures: significant deviations were noted when mixtures contained components heavier than heptune. INTRODUCTION Rapid, accurate methods for calculating the properties of hydrocarbon mixtures are needed for predicting the behavior of natural gas processes. For example, because of the common use of two-phase separation methods in gas proccssing, calculations must be made for the density and composition of equilibrium vapor and liquid phases. In addition, predictions must often be made for the temperature and pressure changes associated with the flow of single- and two-phase natural gas fluids through heat exchangers, chokes and turbines. The complex nature of non-ideal mixtures makes rigorous calculations for these natural gas properties difficult and time-consuming. Natural gas properties have conventionally been determined with generalized data correlations. These correlations, such as the K-values presented in the NGAA Equilibrium Ratio Data Book, are usually based on some average property of the mixture and have proven to give satisfactory estimates for the properties of most oil and gas systems. Digital computers, however, have not only increased the utility of these correlations, but also have made practical the use of equations of state for calculating the properties of natural gases. Potentially, if basic pure component data are available, all the desired thermodynamic properties of mixtures can be derived from a single equation of state describing the mixture. Currently. the best equation of state for describing the behavior of pure, light hydrocarbons over single-and two-phase regions, both below and above critical pressure, is that of Benedict. Webb and Rubin.' The equation contains eight constants which are determined by empirically fitting the equation to pure-component PVT data. Benedict and his co-workers presented the clevelopment of their equation as early as 1940.2 The B-W-R equation is a modification of the Beattie-Bridgeman equation of state and gives better PVT predictions than the Beattie equation at densities above the critical density. Benedict et al. made the equation applicable to mixtures by relating the mixture constants to composition and the constants for pure compounds. These authors, in a serics of articles in 1951,' showed the accuracy of the B-W-R equation when applied to light hydrocarbons and their simple mixtures, and demonstrated the equation's utility for making vapor-liquid equilibria calculations. Since its inception, the B-W-R equation has been the subject of many papers. Numerous additions and modifications have been proposed,'-',"'-':' the purpose of most being to improve the equation's ability to predict PVT properties of specific mixture systems. In 1959, Opfell, Pings and Sage summarized much of the work on the B-W-R equation in their book on equations of state." Since natural gases are primarily mixtures of light hydrocarbons, the B-W-R equation is a natural choice for an equation of state to compute both phase equilibria and thermodynamic properties of natural gases. Consequent-

Jan 1, 1967

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969