Search Documents

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By Herbert E. Lindberg

Laboratory-scale intact and jointed rock masses were tested in field and laboratory experiments to investigate tunnel response in high stress environments. In most of the experiments the tunnels were modeled by a rigid-plastic foam polyurethane with a crush strength of 3.4 MPa (500 psi) and emphasis was placed on jointed rock parameters: joint sets (single set of parallel plane joints versus a double set of orthogonal parallel plane joints), joint plane angle with respect to the direct loading direction, and joint spacing. Other parameters were loading stress, loading direction, and tunnel reinforcement strength. Results show quantitatively the increase in tunnel deformation in jointed compared with intact rocks, double versus single joint sets, and large versus small angle between the joint plane normal and the loading direction. A surprising result was the decreases in tunnel deformation with increases in the number of joints across a tunnel diameter. The efficacy of scale modeling with laboratory-constructed rock was tested by modeling complex reinforced concrete and steel tunnel reinforcements in jointed rock masses and comparing the results with large scale tunnels previously fielded in highly jointed granite. Tunnel response was reproduced in surprising detail, including concrete fracture, steel liner bending and fracture, and critical load to produce these responses. The scale models also allowed sectioning of the jointed rock masses to observe gross sliding along the joints that accompanied tunnel failure.

Jan 1, 1982

By AIME AIME

THOUGH the dust-control systems in the crushing plants and other buildings at Morenci do not differ materially from similar installations in other large copper reduction works, it is probable that in few other plants has as much attention been paid to the dust problem. Possibly the most striking feature of the Morenci installation is the manner in which the necessary equipment has been built into the various structures, and the absence of unsightly pipes, ducts, and fan houses. That this result has been attained is due, in no small part, to the basic conception that the control of the dust in a milling plant should be an essential part of the process itself and not something to be tacked on later after the plant is in operation. The control systems were designed and developed along with the general plant construction program and when the first car of ore was dumped into the crusher the dust-control equipment was ready.

Jan 1, 1942

By E. DeGolyer

THE petroleum production of the world for 1924 again passed the billion-barrel mark, as it did in 1923. A preliminary estimate of production is 1,016,000,000 bbl., a decrease of 1,100,000 bbl., or less than 1 per cent. from the 1,017,100,000 bbl. produced in 1923, the year of greatest production. FIG. 1.-TOTAL WORLD AND UNITED STATES PRODUCTION. Production in the United States decreased 18,500,000 bbl., the. first decrease in yearly production since 1906. Mexican production decreased almost 10,000,000 bbl. Russia, Persia, Roumania, Venezuela, and Peru increased their production by an amount almost great enough to offset the decline in the United States and Mexico. The decline in the production in the United States and Mexico was considerably less than anticipated by leading geologists, economists, and statisticians; nor did the increase in consumption entirely meet the expectations of estimators. Early in the year, the statistical department of one of the most important oil companies forecast a draft on stocks, from an excess of demand over supply, of about 80,000,000 bbl. Instead of decreasing our stocks, they were increased by about 33,000,000 barrels.

Jan 3, 1925

By AIME AIME

T HE year 1920 will be a memorable one in the history of the world's coal supply. The prices reached were the highest of modern times, and as usually happens at such a time, the quality of the output deteriorated. In the last two years of the war, the world's output had risen close to the pre-war level. After the armistice, however, the cessation of munitions manufacture and the delay in resumption of normal business curtailed the demand for coal. Industrial disputes both in Europe and America closed many mines late in 1919 and further reduced the supply. Thus when in 1920 the world set its face to work again and industrial activity was resumed where resumption was possible, consumers' reserves of fuel proved insufficient and an almost universal feeling of apprehension over the coal supply swept around the world. The reasons for this alarm-lately a thing of the past-become clear when the world's production in 1920 is cast up.

Jan 1, 1921

By W. D. Lacabanne

DRILLING fluids as an aid in drilling holes into the earth have been in use successfully for more than a half a century. Originally used in a primitive fashion in water well drilling before the turn of the century, drilling fluids came into their own in 1901 when they were incorporated as an indispensable part of the newly invented rotary oil drilling method. Since drilling fluids have been the basic factor in successful modern oil well drilling, at- tested by the dramatic growth of the U. S. petroleum industry, their study and development have naturally taken place in the oil industry. An abundance of engineering and scientific literature has appeared on the subject of drilling fluids. Application to Exploration Drilling The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig, such as the diamond drill, should benefit by the incorporation of mud fluids in the drilling scheme.

Jan 12, 1954

By John B. Gustavson, Thornton L. Neathery

A geochemical survey was conducted in the gold district in Alabama. Eight old mines were found to be sufficiently large in tenor and tonnage to be economical today. Four of these appeared to be amenable to exploration for new blind deposits. A gaseous aspiration AA method was used on soil samples. The results indicate that arsenic, antimony, and zinc may be good pathfinders for lode gold and residual placers in the saprolite. Antimony and zinc display a high correlation coefficient at gold-bearing locations in contrast to non-mineralized areas. The low cost of this method could make it a tool for selecting detailed targets to be drilled and trenched in the saprolite. Outcrop sampling was found to be inefficient due to paucity of outcrops and lack of correlation between the trace elements and gold in the rock samples, due to extensive weathering. Schistosity changes and silicification, on the other hand, have been found to be helpful in exploration around granite plutons.

Jan 1, 1977

By OTTO HERRES

TO operate the bituminous coal industry in the United States in 1929 cost $770,237,000, of which $30,739,000 was paid for purchased power and $34,947,000 for new machinery and equipment. Equipment aggregated 3,124,000 hp. A mining industry that spends $65,000,000 a year for power and machinery is likely to be fairly well mechanized, and when the machinery in use takes three million horsepower to drive it, the probabilities are that mechanization has been in progress in at least some of the mines for quite a few years. Mechanization in its broadest sense implies machine cutting, power drilling, mechanical loading, electric haulage, mechanical sizing and cleaning, and lesser applications of machinery to mining operations. But the introduction and development of mechanical loading has been the feature of coal mining recently and its extraordinary progress is causing great changes within the industry. First, let us look at the records. The quantity of coal loaded mechanically in bituminous mines was:

Jan 1, 1933

On the following pages are abstracts of papers published by the Institute during the year 1936 as TECHNICAL PUBLICATIONS and CONTRIBUTIONS, papers in bound volumes appearing for the first time, and papers in MINING AND METALLURGY For abstracts of papers that appeared in bound volumes in 1936 but that were published as TECHNICAL PUBLICATIONS in 1935, see the YEAR BOOK dated January 1936.

Jan 1, 1937

By Patricia J. Rand, Kailish Narayan

Atlantic Richfield Co. began operating a commercial uranium solution mining project in April 1975, in Live Oak County, Tex., 10 miles southwest of the town of George West. The operation is designed to produce 250,00 lb of U308 per year and is jointly owned by Atlantic Richfield Co., Dalco, and U.S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural cattle ranching and farming---but several producing gas fields are present in the areas as well. A nine month enviromental baseline study was conducted on the property beginning in Feb. 1975. Plants and animals of the Clay West area were identified and representative terrestrial and aquatic communities were analyzed. Physical and chemical parameters of the soils were described and analyzed. The surface and underground waters were analyzed chemically; radionuclides, heavy metals, nutrients, and pesticide concentrations were measured in the creek sediments; bacteriological measurements were made in creek water and sediments; radionuclide and chemical levels in plants and animals, both terrestial and aquatic, were measured. These studies, though not required by existing, state or federal laws, were considered necessary to assess the existing conditions before operations began on site. The in-place leaching technique for uranium mining eliminates the enviromental disturbances associated with open pit or underground mining. No grinding and crushing of ore is needed, nor are large tonnages of waste tailings produced. Surface subsidence is not expected since less than 5 lb of uranium is present per ton of rock and even complete removal of such small amounts should not cause subsidence. Solution mining has fewer environmental problems than conventional mining. Members of the Texas Water Quality Board recognized the differences which exist and have recently formulated new environmental control procedures which apply specifically to solution mining. Some of the solution mining activities which are of particular concern are discussed in the following pages. Process Description The produced uranium-bearing solution is pumped through a pipeline from the pattern area to the plant area. The first pattern area consists of a nest of 125 fluid injection, production, and monitor wells [(Fig. 1)]. Injection wells have 4-in. casings and are spaced 50 ft apart on a square grid. Production wells have a 6-in. casing and are located in the center of each square. A block flow sheet of the plant is given in [Fig. 2]. The produced solution goes through parallel trains, each consisting of a carbon column and an ion exchange column in series. The carbon column removes any sand present in the produced solution and the ion exchange column extracts the uranium. The depleted solution is treated with chemicals and returned to the field for reinjection. The uranium retained in the ion exchange column is removed periodically with a sodium chloride solution. Uranium-bearing solution from the ion exchange column is passed through a charcoal column for removal of impurities and then to a precipitation tank where the uranium is precipitated as yellowcake slurry. The yellowcake slurry is clarified, filtered and dried to produce a granular yellowcake product. Environmental Considerations Sources of waste solutions to storage reservoirs, the backwash reservoir and atmospheric discharges are shown in the block flow sheet [(Fig. 2)]. These waste solutions pose a relatively small problem and are adequately controlled by conventional means. There is one area, however,

Jan 1, 1978

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

By M. W. BERNEWITZ

ALTHOUGH many persons know that a lot of type metal and etchings are used in the U. S. Government Printing Office few would expect to find anything on metals in the annual report of the Public Printer, George H. Carter. Yet the report for the fiscal year ended June 30, 1931, contains many interesting items. For example: Among the 57,500,000 lb. of materials and supplies delivered to the printing office was little new metal, but the metal in circulation is 6,000,000 to 7,000,000 lb. In the cost of production $31,523 is charged against metal, nearly one-third for salaries and wages. In miscellaneous sales were $4,696 from waste metal and $1,147 from waste gold (from books). Electrotype and stereotype covered 11,438,314 sq. in. The vaults and storage rooms contain 1,700,000 plates and 130,000 pages of type containing 4,600,000 lb. of metal valued at $275,000. In what was known as the Congressional Globe vault were 46,000 stereotype plates; these were salvaged by remelting for other platemaking service. The Congressional Record superseded the Congressional Globe in 1873.)

Jan 1, 1932

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By Paul Queneau

Some years from now, perusal of the unfolding saga of the nickel family will show that the year 1968 was the herald of change-both in the geography of its endeavors and in its technology. No one should doubt any longer that oxide ores of nickel have come of lusty age-their heavyweight stature in the Caribbean area and in the Western Pacific can be shrunk only by immersion in the politics of unhappiness. The sulfide branch of the family has been augmented afar off by substantial ore deposits in western Australia-right across the globe from Sudbury-and in southern Africa, 9000 miles from the nickel hub. The Foreword of the 1961 AIME volume, dealing with the extractive metallurgy of copper and nickel, noted that "the dead hands of nitrogen" had been lifted from oxidation reactions utilizing air and that the industry was on the threshold of under- standing this fact. Here, at least, nonferrous industry had led its ferrous counterpart in the commercial use of tonnage oxygen in liquid phase pyrometallurgy-the reference is to oxygen flash smelting. Today large oxygen-producing plants are blossoming everywhere and the fruits which will follow are many and varied. Among them is Inco's forthcoming use of the top-blown oxygen converter for sulfide melts. The bell tolls for those "pyro- metallurgical dinosaurs" which still stalk smelter aisles the world around. Silicate oxide nickel ores will rejoice in the glow of modern elevated temperature chemical metallurgy in its various manifestations, vindicating the bulldog spirit of that ancient of clans, the hot metal men-including the renovator of Le Nickel's Doniambo Works.

Jan 10, 1968

By Stewart. J. W.

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only. 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, q gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By E. O. Kirkendall

THE investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,' particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize; it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosenhain,2.3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,7 and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,' and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. EXPERIMENTAL PROCEDURE This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ±3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 34 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photo-micrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 3a hr. at 300°C. It was then etched in 25

Jan 1, 1942

By N. E. Grosvenor

The study of rock mechanics is becoming more important each year and several groups are currently engaged in the study of rock mechanics instrumentation and techniques that can be used to determine rock properties in place. As it becomes necessary to mine lower grade ores, larger equipment and tonnages are required, which in turn call for larger openings underground. In addition, rock mechanics studies are necessary for designing large underground openings for defense and powerhouses, and highway and water tunnels. Meramec Mining Co. has a rock mechanics program in which they are trying to develop a means of detecting ground instability prior to failure. In one case advance warning resulted in valuable lead time for back filling stopes before pillar failure had progressed to a dangerous extent.1

Jan 2, 1968

By R. S. Moehlman

IN recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. COST OF DRILLING Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 50 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $1 per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft., as more time is consumed in pulling rods. 3. Cost of preparing drilling stations, getting air underground to stations, etc. 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958