Search Documents

By R. Laird Auchmuty

FOREWORD THE A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing Co. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. HOWARD N. EAVENSON, Chairman, Subcommittee on Bituminous Coal Mining.

Jan 1, 1931

By Thomas L. Watson

The occurrence of zircon in pegmatites of acidic composition is recorded by many observers both in this country and abroad, and they form one of the most important geologic modes of occurrence of the minera1. As is well known, commercially the most important American locality for zircon is near Zirconia in Henderson County, North Carolina, where many tons of the mineral have been obtained from a kaolinized pegmatite dike 100 ft. wide and traced for 1 1/2 miles along the direction of strike N. 50" E. Zircon may be developed in pegmatites as inclusions in the principal rock-forming minerals, chiefly quartz and feldspar, and as a separate megascopic constituent in the form of grains and crystals not exceeding, as a rule, 2 in. in size, and usually smaller. In the Henderson County, North Carolina, pegmatite, zircon occurs in prismatic crystals with pyramidal terminations measuring up to 30 mm. in diameter, associated chiefly with the feldspar. In some of the apatite veins of Canada, which are closely allied to pogmatite dikes, zircon is reported in crystals upward of 6 in. in length and 2 in. and more in thickness. Zircon in large masses occurs in Virginia in the well-known pegmatites near Amelia in Amelia County, and near Gouldin in Hanover County. Both localities are in the middle eastern portion of the Piedmont Plateau province, and are separated by a distance of about 40 miles in a northeast-southwest direction. The rocks of both areas, including the pegmatite bodies, are in an advanced stage of decay, and the hard and moderately fresh rocks are concealed beneath a cover of variable thickness of rock decay derived by the normal processes of weathering. Exposures, there-

Jan 1, 1917

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By J. A. Fulton

GOLD was discovered in the Sierra Nevada by J. W. Marshall on Jan. 2, 1848. The town: of Grass Valley soon sprang up and contained several stores in 1849; but the population of the town has always reflected the fluctuations in quartz mining. Gold-bearing quartz was found on Gold Hill in September 1850, and in the next two years most of the quartz bearing veins in the vicinity were located. At first, the quartz was crushed in mortars with spring poles; the Huff Co. took out $20,000 in this manner during the winter and spring of 1851. The first mill was put up in January, 1851. In 1866, there .were in Grass Valley 248 stamps, crushing 71,420 tons of ore with an average yield of $30 to $35; in Nevada City, there were 142 stamps, crushing 14,200, tons, with an average value of $25. But in 1918, only two properties in. this region, the Empire and the North Star, were producing. Since then, there has. been a revival of mining in the district and the following properties are being opened up: The Golden Center, Grass Valley Gold. Mines CO , Idaho-Maryland Mines Co., while the Sultana is kept unwatered and work is going on in a half dozen small properties.

Jan 2, 1926

By S. W. Miller

MOST of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,1 that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., when he has found them in large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than ;3/4 in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top ;1/16 in. (1.5 mm.) of the weld, they were removed by the grinding or machining; also, welds ¾ in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was

Jan 2, 1919

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

THE progress in lead smelting practice in the United States during 1930 has been along previously defined lines. Since most of the material treated is high-grade concentrate relatively high in zinc, practically all the plants have been forced to adopt double sintering. This generally results in there being' no matte fall, and most of the copper in the charge is recovered in the furnace dross. The furnace dross is . smelted with. scrap iron and flux .in small reverberatories, giving a shipping matte or speiss high in copper and low in lead. Details of this reverberatory. furnace practice vary at the different plants. There is a decided tendency toward moreintensive filtration of blast- furnace and sinter fume. Bag capacity has been in- creased by using higher pressures and more frequent shaking.

Jan 1, 1931

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By Lucien Eaton

THE accuracy with which detachable bits can be sharpened and gauged by grinding has made possible refinements in design that cannot be attained by forging. This applies particularly to gauging, where accuracy is of the greatest importance. Gauge changes of 1/32 in., and even 1/64 in., are now feasible, whereas 1/16 -in. changes are about the limit in accuracy for forged bits. These small changes in gauge are feasible, however, only with certain fundamental principles of design. Within reasonable limits the depth to which a hole can be drilled is dependent primarily upon the loss in gauge, or diameter, of the bit. In drilling there is always a certain amount of "overdrilling"-the bouncing of the bit in the hole and its rotation wear away the walls-so that the actual diameter of the hole is greater than the diameter of the bit. The amount of this overdrilling depends upon the kind of rock being drilled, and is sometimes sufficient to permit the use of the same diameter of bit for the full depth of the hole. If, for instance, a 1 3/4-in. diameter bit overdrills 1/32 in. in diameter, and loses 1/64 in. in gauge in drilling 2 ft. of hole, the bottom of the hole is still 1/64 in, larger than the original diameter of the bit, and a new 1 ¾ -in. bit can be used to drill the next 2 ft. If, however, the overdrill is less than the loss in gauge, the next bit must be of smaller diameter. The first requisite in reducing loss of gauge in drilling is to have the points and corners of the wings of the bit cut circles of the same diameter, thus producing a reaming surface with continuous bearing on the wall of the hole. The greater the reaming surface, the less the gauge loss that is to be expected. If the reaming surface, however, is too large, it may impede the rotation of the bit through excessive friction. This principle was probably first recognized in the design of the Carr bit (Fig. 1), a bit with a single cutting edge of wide angle, a definite reaming edge, and a large center hole. The same idea was followed in designing the double-taper cross bits, which are now standard almost everywhere.

Jan 1, 1939

By Alan Bauer

DRILLING CONSIDERATIONS In considering blasting it is necessary to consider the drilling and explosives since one is generally concerned with the total cost of muck of a certain size in the pit or through the crusher. To get a current idea of the drilling situation in open pit mines plotted in Fig. 1 are the drilling costs per ton of material vs. hole diameter for rotary drill holes in large limestone, iron ore and taconite operations. The exception is the 2-in. diam hole which was drilled with a percussion drill in limestone. Each curve in Fig. 1 represents a different operation and the data cover many months of production drilling. The costs are total operating and maintenance and do not include machine depreciation. As the hole size is increased so are the machine size and the investment. Providing the tonnage is available to be drilled, then as the machine size goes up so does the productivity-markedly-and this same shape of curve applies. In some instances it is even steeper. The interesting thing to note is that in each case studied there is a substantial drop-off in cost/ton as the hole size is increased. This is true for the softest material considered, limestone, through to the hardest, taconite. How has this come about? In going from 10-in. to 123-in. diam holes, the powder factors have generally stayed about the same and the same type of muck has been produced. To date this has been mainly in the softer materials but it has also been steadily taking hold in the harder ones. On this basis, then, patterns are generally expanded as the ratio of the hole diameters or close to it, if the explosive type is kept the same. In the harder rocks the cost per foot of hole has increased somewhat so that the overall reduction in drilling cost per ton is about 25 pct. In somewhat weaker rocks of about 25,000 psi compressional strength the drilling cost per

Jan 1, 1968

While coal was undoubtedly seen by the early travellers within the state, the first mention of it was in the late 1820's when hunters put some stones from a creek bed under the logs of a large camp fire, and awoke later to find the stones on fire. The stream was later named Coal Branch; the location was at the eastern side of the present Bibbs County.1 In the Louisville Daily Journal of Feb. 11, 1831, the following short editorial note appeared: "Tuscaloosa Coal.-A small quantity of this article has reached Mobile, and has been tried in the office of the Patriot; it is said to be an excellent article. We invite such of our friends as desire economy in fuel, love a cheerful and constant fire, or would eschew a smoky room, to call and examine." On a geological map published in 1832, the "Carboniferous group" is shown and a spot near Tuscaloosa indicated as showing bituminous coal,2 and this is again alluded to in Morton's Synopsis, 1834. A brief description of the coal fields in the state in 1834 said that in winter coal was brought down the. Black Warrior River to Mobile and sold there at the same price as Liverpool coal, $1.00 to $1.50 per barrel, ($10 to $15 per ton) and that the writer was using it in his laboratory.3 At that time it was in local use by smiths and an iron foundry was using it in Shelby County.4 In 1836 some coal was mined in the Birmingham district, chiefly in the northern portion of the Coosa basin, where it was loaded on barges and taken down the Coosa Rivers.5 "William Whitman dug coal out of Wolf Creek (Walker County) in 1837," and in the same county, in 1839, the first coal shaft in the state, was sunk. This was near the mouth of Lost Creek and was known as Frierson's Shaft. It was operated by a hand windlass, using two tubs.1

Jan 1, 1942

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

By YANG TSANQ WOO

THE method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom, In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, both being .connected at the bottom by a flue as shown in Fig. 1. The sides and bottom of the kiln are lined with fire-bricks, and covered with a layer of fire-clay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending .2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each intervening space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water; in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good " dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Nov 1, 1905

By Allan B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drill- holes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 ¼ -in. diam, on 25-ft and 100- ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals.

Jan 7, 1959

By Horace Williams

IN VIEW of the frequent occurrence of petroleum in other parts of the world, it seems odd that so large an area as is contained within the borders of Brazil should be without this product. This apparent deficiency may be due, however, to our ignorance of the regions in which-it, may exist. In some places, indications point to the probable existence of petroleum in ages gone by; and while the presence of petroleum pools may be problematic, in several regions conditions not unfavorable to their occurrence exist. Yet, Brazil has enormous oil resources in the rich oil-shales in different parts of the country. Many of these shales are very rich and only suitable processes for the extraction of the oil are lacking. At the present time, only a few small experimental plants are producing oil by distillation from these shales. These plants have been the subject of recent investigations by the Geological and Mineralogical Survey, a. pre-liminary report of which is in the hands of the printer. The only regions where studies have not been made are the upper Amazon, the Acre, the Rio Negro, and the Peruvian frontier, which really seems to be the most promising field for, explorations of any in the country. In the vast plateau region of the interior north of the 20th parallel of latitude, granites, gneiss, mica schists, and, very old metamorphosed sedimentaries predominate. Later, sedimentaries occupy a minor position and, where found in the interior, represent a thin veneering resting on the older rocks. At several places near the coast they have a greater development and contain considerable beds of oil-shale and may, in some cases, offer conditions favorable for the occurrence of oil. Such deposits are found in the Permian rocks of central-and southern Maranhão; in the Tertiary and Cretaceous beds along the coast of Alagôas Sergipe, Bahia, and perhaps farther south in Espirito Santo; and in the Parahyba embayment north of Cape Frio and in the interior Tertiary basin of eastern Sao Paulo.

Jan 9, 1920

By Lloyal O. Bacon

In the spring of 1952 Calumet and Hecla Inc. began a geophysical program near Shullsburg, Wis., in the Wisconsin-Illinois lead-zinc district, to assist the geological and drilling exploration programs. Sphalerite, the ore mineral in this area, occurs with a considerable amount of marcasite. In general the higher the percentage of sphalerite in the ore, the higher the percentage of marcasite; however, there may be mineralized zones high in marcasite but low in sphalerite. Orebodies in general are relatively narrow and elongated.

Feb 1, 1956

By L. O. Howard

WHAT was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyère line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Falls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. .About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to handle the total output of copper in these small shells until the standard. Great Falls converters were substituted in June, 1914.

Jan 9, 1916

By W. C. Wright

A PRACTICAL program of education for workers of the mining industries is being formulated by the Federal Board for Vocational. Education in cooperation with the States in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational' education and for cooperation with the States in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the-1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manufactures Mines and Quarries Employees 7,405,313 1,109,410. Capital $18,428,269,706 $3,380,525,841 Value of product $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the, production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all States have set up educational and technical standards , for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some States, every miner must have a certificate, which is issued by the mine examining board. only after an oral examination.

Jan 1, 1919

By P. H. Royster

SOMETHING of a mystery has attached itself to the production of ferromanganese in the blast furnace. This alloy has been produced on the Continent almost continuously since 1876 and in very considerable tonnages, but little definite information concerning the practice is to he found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country prior to 1904, bit one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public. In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many, as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations. Realizing the advantages both to the country and to the industry from a pooling of operating data and experiences, the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Although the results of this investigation have already been reported to the companies cooperating, they may he of permanent metallurgical interest, so this paper attempts to give, briefly, the more important points brought out in the investigations. OPERATING DATA IN FERROMANGANESE PRACTICE Operating data were collected by the Bureau from 11 ferromanganese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P. The dimensions, of seven of the furnaces are given in Table 1. The companies from whom this infor-

Jan 2, 1919