Search Documents

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Francois E. Heuze

INTRODUCTION Rock slope stability typically is governed by the geological discontinuities. This stability can be improved by drainage, unloading, adjustment in slope orientation, adjustment in slope angle, and also by reinforcement such as bolts or tendons. This paper addresses the modeling of bolt reinforcement in rock slopes. Most geological discontinuities such as joints have rough surfaces; they dilate during shear displacement. Their shear strength is characterized by two envelopes (Fig. 1); the peak envelope is distinct from the residual envelope when the joints can dilate. If the dilation is restrained transversely, such as with bolts, the normal stress will increase and the joint strength also will increase. It has been demonstrated that this increase may be considerable (Obert et al., 1976). The new normal stress at peak strength is a com- posite function of the properties of the rock mass and of the steel (Heuze, 1979). Hence, the dilation and its resultant effects on joint shear strength must be included in the analysis and design of the reinforcement. We present a model which can be used to perform such an analysis. Early studies of rock reinforcement in mining and civil applications (Lang, 1957 - Panek, 1962 - Osen and Parsons, 1966 - Lang, 19721, did not consider the specific effects of bolts on joint shear strength. In 1973, Heuze and Goodman reported direct shear tests on rough sandstone joints with bolts perpendicular to the joint plane (Fig. 2). The peak shear strength of such joints was greatly in excess of the shear strength of the unbolted joints. The excess

Jan 1, 1983

By D. Gupta

Rates of autothermic reactions are sensitive to temperature variations to the extent of potential extinction of the reaction. Such reactions, when carried out in the countercurrent mode with feed-back of energy between reacting phases, may result in the possibility of multiple steady-states. In regions of great sensitivity, minor variations, especially feed-temperatures, are an important criterion for such instabilities. Mathematical models have been used to delineate the parameter-fields in which instabilities might occur. The metallurgical system chosen to experimentally verify the above theoretical findings was the exothermic oxidation reaction of magnetite to hemitite.

Jan 1, 1977

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation [ ] in which y = cumulative percent finer, x = particle size, = distribution modulus, and k = size modulus. Charles found that the energy consumption in comminution is usefully expressed by another empirical relation, [ ] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; ( 1-n) is the slope of a plot of log E vs log k. Holmes has presented energy equations similar to Eq. 2.

Jan 2, 1960

By Joseph A. Gill, Ernest A. Curth

The Government and Leeco concluded a cost-sharing agreement in 1976 to demonstrate longwall mining of a thin coalbed, 1 m or less, in a mine near Hyden, Ky. A premining investigation laid the groundwork for mine design and equipment specifications. Four- legged shields, a face conveyor, a stage loader and an in-web shearer were selected to operate on a 183 m face. Lengwall mining began in 1979 and initially was slowed by low mining height and equipment problems. A rock mechanics program provides early warning capability and criteria for future mine design. Monitoring of surface effects is included.

Jan 1, 1981

Raymond Weir Smyth, born Nov. 3, 1888, was the son of Herbert Weir Smyth, professor of Greek Literature at Harvard University. He graduated (A. B.) from Harvard in 1909 and later pursued advanced studies there in chemistry and in metallurgy. He held the position of metallurgist for the American Steel and Wire Co. at Worcester, Mass., and also for the Steel and Tube Co. at Youngstomn, Ohio. For a time he was inspector of munitions for the British Government and stationed at the Railway Steel and Spring Co. at Latrobe, Pa. For a short time, in 1917, he was Inspector of Ordnance for the U. S. Government, and the following year, having entered the U. S. Naval Reserve Force, he was ordered in a similar capacity to the Midvale Steel Co. In September, he removed to the Navy Yard, League Island, Philadelphia, to train for the obligatory minimum of six months' sea duty. There he contracted influenza, which was followed by pneumonia, from which he died, September 27, at the Navy Yard Hospital. Captain Braxton Bigelow* Captain Braxton Bigelow was the son of Major John B. Bigelow, U. S. A., retired, and grandson of the late John Bigelow, author, and Minister to France under President Grant. Captain Bigelow graduated

Jan 1, 1920

By Albert L. Toenges

C. P. HEINER*—I would like to ask Mr. Toenges about the highest rank coal. I did not get that clearly. What kind of coal is that? A. L. TOENGES (author's reply)— The coal in the Matanuska field ranges from high volatile "B" bituminus to anthracite. It all depends on which direction you go in the Matanuska field. C. P. HEINER—Is it a large reserve. A. L. TOENGES—That is what we hope. That is what we are trying to find out. B. W. DYER*—In those strip beds, I wonder how far back the coal would weather ? A. L. TOENGES—I never noticed particularly. B. W. DYER—The weathering does not extend back like it does in this country ? A. L. TOENGES—No, it does not. B. W. DYER—Is that due to the freezing ? A. L. TOENGES—Probably so. B. W. DYER—In this country, you would expect nothing but weathered coal. R. H. SWALLOW*—Along that line, you mentioned some of the seams were on fire. Did you ever know how far back they burned, or was it hard to tell ? A. L. TOENGES—The fires occurred in the mine. That one you refer to was from an inside fire.

Jan 1, 1950

By John Goheen

CONSIDERABLE work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods ¼ in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constructed to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses 2200-2250° F. (1205-1234° C.) Yellow brasses 2250-2400° F. (1234-1318° C.) Bronzes 2300-2550° F. (1260-1400° C.)

Jan 11, 1921

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By C. A. Zapffe

BOTH the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. BLEEDING, RISING, AND PIPING The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinction between bleeding and rising in reference to killed metal.* POROSITY Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth1 noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel-oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1942

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By F. N. Rhines

Despite the large amount of study which has been devoted to the subject our present knowledge of the copper-oxygen system remains incomplete and unsatisfactory .in many respects. This applies particularly to those regions in which solid metallic copper exists. The primary object of the present paper is the contribution of new information relative to the solid solubility of oxygen (or cuprous oxide) in copper at atmospheric pressure, together with certain observations in the low-pressure regions of the system. It seems appropriate also to present a brief summary of the outstanding previous work on the constitution of mixtures of copper with its lowest oxide in order. to show the relation between the new facts and the system as a whole. The earliest recorded investigations of the copper-oxygen system are those of M. S. Lucas(l) $ and of M. Chevillot(2) in 1819 and 1820. Lucas believed that liquid copper is capable of dissolving its oxide, but neither he nor Chevillot was able to furnish convincing proof of this property. It was not until 1866 that T. Graham(3) definitely established the existence of such a solubility. Nine years later W. Hampe(4) measured its extent and roughly outlined the copper-rich portion of the system. The first really precise examination of the constitutional relationship between copper and cuprous oxide, however, was that of E. Heyn(5) who in 1900 published a temperature-concentration diagram covering the range from 0 to 10 per cent of cuprous oxide at atmospheric pressure. Within these limits of composition cuprous oxide was found to dissolve in liquid copper, forming at 3.4 to 3.5 per cent a eutectic which melted at 1065" C. R. E. Slade and F. D. Farrow(6) extended these studies to mixtures of higher oxygen content. They discovered that between 20 and 95 per cent of cuprous oxide the metal and oxide form two liquid phases at a monotectic reaction of 1195" C. The span of the biliquidal region diminishes slightly

Jan 1, 1934

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By Charles H. Doolittle, Royal P. Jarvis

The following notes are contributed, not with the idea of offering a complete history of the development of this very important process as applied to the Leadville district, but with the hope that the practice, as it was carried out in the Bi-Metallic Smelter, may still be of interest to others. The Bi-Metallic Smelter, at Leadville, Colo., was the first to make a commercial success of the process described in the following pages, which consisted essentially of smelting raw silver- and copper-bearing sulphide ores in blast-furnaces to form a matte, which was generally re-smelted with siliceous ores for a second high-grade matte. Robert Sticht, in his excellent monograph on the subject,' has outlined briefly the plant belonging to this company. He says, in effect: The Boulder, Mont., enterprise set the example for others with whom the patentee (W. L. Austin) had been negotiating, and the old La Plata lead-smelter at Leadville, Colo., was fashioned into a crude, temporary experimental plant for the Bi-Metallic Company, and the feasibility of the process demonstrated by a trial run. Subsequently, the plant was considerably improved, and, being supplied with very favorable ores, continued to run without interruption from August, 1892, to June, 1893. In September, 1803, smelting was resumed in a completely remodeled establishment, some $200,000 having been expended upon the new work. Thus, aside from the Montana experiments, which, under the direction of W. L. Austin, began as early as 1885 at Toston, and continued with indifferent success for six or seven years, the Bi-Metallic plant at Leadville may be said to have

Jan 1, 1911

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

CANADA, which appears to be growing into one big mining camp, may soon be the background for another impressively large iron ore development. And again it will be Fenimore Iron Mines who will be the motivating force. Dr. J. A. Retty, Fenimore president, who was one of the important figures in the development of Labrador iron deposits, predicts a great future for property on the west coast of Ungava Bay in deep northern area of New Quebec. Fenimore properties consist of a 200 sq mile concession in addition to several hundred claims over about 112 miles along the Labrador trough, mainly in the Ungava Bay region.

Jan 5, 1953

By Leonid Bryner

For many years, geologists have inferred a connection between the evolution of the earth's crust and ore deposition, a connection coming under the heading of metallogeny. In recent years the concept of metallogeny has assumed major importance in the exploration planning of Russian geologists in their quest for new mineral sources. As defined by Radkevich, metallogeny is "the science which studies the laws governing the distribution of ore deposits in the earth's crust." However, since it can be argued that metallogeny does not contain enough certitude to be classified as a "science," it would be more appropriately defined as the study of metallogenic provinces, and metallogenic epochs.

Jan 6, 1963

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

By Edward Keller

ALTHOUGH the subject matter contained in this paper is presented under a new title, its writing was induced by the work of S. Skowronski and K. W. McComas.1 A discussion of the latter is here combined with the presentation of new and independent data. The physical constants quoted by the authors of that paper, such as melting and boiling points, as also the chemical reactions of the substances involved, are so well established that the numerous confirmatory experiments and their application to metallurgical conditions leave little or no room for criticisms. On the contrary, they will greatly aid to dispel any lingering skepticism as to possible considerable losses of copper accruing when the metal is melted in the presence of its own and, probably, other chlorides and when no provision is made for the recovery of volatile products. Exception may be taken, to some degree, to that part of the work under the caption Melting Drillings of Copper Mixed With Sodium Chloride. These experiments should have been extended in order to make the implied reactions clear and the results convincing. The latter are stated to be, "that when sodium chloride is present above certain minimum quantity relative to copper some of it is found to volatilize in the melt while another part reacts with the metallic copper to produce the volatile cuprous chloride, and that When smaller quantities of sodium chloride are present the reaction is complete and all chlorine is found to have volatilized as cuprous chloride." Metallic copper and sodium chloride are mentioned as the sole reagents in this chemical process, acting, according to the authors, in a neutral atmosphere of carbon dioxide. The chemist, quite naturally, will inquire into the formula according to which that reaction takes place and find that it would present itself as follows: 2Cu + 2NaC1 = 2Na + Cu2Cl2 It would appear that the truth of this formula will be challenged and a more rational explanation of the reaction sought. Apparently, carbon dioxide is neutral relative to metallic copper in its molten state; whether it remains neutral in the presence of sodium chloride is quite another question. Does it not at that high temperature become an oxidizer and do not the conditions of the reaction change to those expressed in the following formula? 2Cu + 2NaCl + 2002 = Na2CO3 + CO + Cu2Cl2

Jan 9, 1919