Search Documents

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By James H. Hance

Discussion of the paper of JAMES H. HANCE, presented at the New York meeting, .February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 299 to 326. FREDERIC P. DEWEY, Washington, D. C. (communication to the Secretary*).-I wish to congratulate Professor Hance and to thank him for his extremely valuable addition to the fund of data upon this subject. It presents clearly conclusive and incontrovertible proof of the unreliability of drill samples of this class of metal for determining the value of such bullion. I am afraid, however, that his hope that some one in the mint service might continue such an investigation upon a more elaborate and exhaustive scale is, for the present at least, doomed to disappointment. As a practical matter, the mint service is not now particularly interested in segregation in crude bullion. So much trouble and friction arose, -both in the original purchase and in the transfer from one institution to another, in handling segregated bullion, that it became necessary to adopt drastic measures and now it is seldom attempted to determine the value of such bullion in the service. When bullion known or even suspected of being segregated is presented for purchase, it is at once strongly refined in the pot and the disturbing elements so far removed that concordant assays may certainly be obtained from the dip samples and a reasonably fair agreement obtained from drill samples. The mint service prefers that the owner should refine his bullion himself, but if he does not we will do it at his expense and return the slag to him when desired. Much work has been done in the mint service trying to arrive at the value of deposits of segregated bullion without strong refining. It was no unusual thing for such deposits to be melted three times at the purchasing office and to have 30 to 40 assays on the metal made before buying it. Yet when shipped to a mint it was found necessary to melt two or three times more and to make 15 to 25 assays before the mint would accept the bar, and there were considerable differences between the valuations of the two offices. In what was undoubtedly the worst case ever investigated, the purchasing office melted the deposit, 953 oz., three times, with a loss of 105.5 oz., and made 46 assays; the mint melted three times, with a loss of 6.6 oz., and made 28 assays. The mint allowed the purchasing office 1.178 oz. of fine gold more than the purchasing office claimed, while an extensive investigation of the mint samples by the Bureau, in which over 100 independent assays were made in various service laboratories, indicated that the metal carried 0.7 to 0.9 oz. more of fine gold than the mint allowed. Preliminary assays on the original metal

Jan 5, 1916

By Malcolm J. McPherson, Michael Hood

Sunnyside Mines, owned and operated by the Kaiser Steel Corporation, are situated near the city of Price, Utah. The complex comprises three adjacent mines, named simply Nos. 1, 2 and 3, all connected underground. Two seams, the upper and lower Sunnyside have been worked. These dip at about 10 percent to the north-east. The surface cover is variable due to the mountainous nature of the topography. The Sunnyside upper seam varies from 5 1/2 ft (1.7m) to 9 ft (2.7m) In thickness whilst the lower seam remains at about 6ft (1.8m). The separation between the two seams has ranged from 7 to 45 ft over the mined area (2 to 14m). Longwall mining has been practiced at Sunnyside for over 20 years due to difficulties of roof control encountered when using the roan and pillar system. Number 3 mine is bounded on the north and south sides by mines Number 1 and 2 respectively. Whilst current production is concentrated into Number 1 mine, much of the future of the complex lies in the further development of deeper reserves in Number 3 mine. Workings in this latter mine were curtailed in 1978 due to difficulties in ventilation. Present developments are ventilated partially from the neighboring Number 2 mine where no workings are in progress. The layout of Number 3 mine is illustrated on the schematic Figure 1. Trunk airways extend down dip from the surface at No. 2 Canyon and the Water Canyon for a distance of some 9,600 ft. (2930m). The area between the two sets of trunk airways has been worked extensively in both seams as have the corresponding reserves on either side in the connected adjacent mines. At the present time exhausting fans are sited at the top of a shallow shaft in No. 2 Canyon and an 8 ft (2.4m) diameter shaft sunk to a depth of 1013 ft (310m) closer to the current developments (Figure 1). The current airflow system, even with an additional 116,000 cfm (55m3/s) entering from No. 2 Mine, is adequate only for the development work now in progress but will be unable to support new longwall faces further downdip. The basic ventilation problem of this mine may be stated quite simply. In a situation where all intake and return airways pass through extensive old workings, a ventilation system design was required that would be effective, efficient and economic for the foreseeable future of the mine. ORGANIZATION OF THE PLANNING PROCEDURE The procedure followed during the study is illustrated on Figure 2. Initial ventilation surveys established the current state of the airflow system and provided the necessary data for setting up a Basic Network File in a computer store. The data in this file was a mathematical model of the ventilation system of the mine. The basic network was analysed by a ventilation network analysis program in order to correlate the measured and computed airflows and to establish the basic network as a true representation of the mine as it stood at the time of the surveys. The network model could then be extended to simulate the future development of the mine and alternative ventilation designs investigated. The remaining sections of the paper outline the work involved in each of these main phases of the planning procedure. VENTILATION SURVEYS Conduct of Surveys Two types of measurements were conducted simultaneously throughout the air-carrying routes of the mine: (i) Airflow measurements were made by anemometer traverse or smoke tube at 221 selected stations. Anemometer traverses were repeated at each station until at least three gave results to within 5 per cent. (ii) Pressure drop measurements were made across ventilation doors, regulators and, wherever possible, across stoppings. Additionally, frictional pressure drops were measured along airways where such pressure drops were significant (above 0.01 inches of water gauge or 2.5 Pa over a 100m distance). The trailing hose method was used to determine these frictional pressure drops. This involved laying out 100m of abrasive resistant plastic tubing (3 mm internal diameter) with a 4 ft. pitot-static tube facing into the airflow at either end and a low range pressure gauge connected into the line. The trailing hose method was preferred to the alternative barometer technique for this study because of (a) the relative ease of access between measuring points and (b) the greater accuracy within individual airways. The anemometers used were Davis Biram Type A/2-3" (30 to 5,000 ft/min) and Airflow Developments AM-5000 digital (50 to 5,000 ft/min). The pressure gauges employed were Dwyer magnehelic instruments. These were preferred to liquid in glass manometers because of their portability and dependability under adverse mining conditions. A checklist of the equipment used in the survey is given in Appendix 1. The instruments were calibrated before and after the surveys in the mine ventilation laboratory at the University of California, Berkeley. The survey occupied two teams, each of three men, for ten working days. The work consisted

Jan 1, 1982

By Madan M. Singh, William J. Courtney

Pneumatic stowing is commonly employed in European coal mines, but is not used in the United States. This paper reports a study conducted to analyze the conditions under which pneumatic stowing might be advantageously used and the techniques and costs involved in order to effect this. Although stowing may reduce the subsidence in a mining area, this does not entirely eliminate the surface damage. Besides, the cost of stowing will run about $1.50 to $3 per ton of coal mined not including the cost of fill material, if it has to be bought and transported to the mine. Stowing my, however, be economically viable under special circumstances such as in thick, steep, or contiguous seams.

Jan 1, 1976

By S. P. Sharples

HAVING occasion a few weeks ago to investigate the subject of black band iron ore in West Virginia, I was surprised at being met at the outset with a denial of its existence. One gentleman went so far as to offer one hundred dollars an acre for any land in West Virginia that contained a seam or vein of even a single foot in thickness, and when shown the ore he acknowledged that it was genuine, but declared it had been imported. That black band does occur in West Virginia is to-day well known to a number of persons. There is a seam on the Gauley River of about a foot in thickness of good ore, which I understand Mr. Lewis and others are making preparations to work. The great trouble with black band ores as heretofore found in this country has been their limited extent. At Fort Washington, for instance, they had a very fine show ing of ore, but it soon gave out. It has also been asserted that the black band ores of the Western Coal Measures were worthless in the furnace, and Fort Washington has been pointed out as an example of the fate of any one who should undertake to work them. But they have been successfully worked at Youngstown and in other parts of Ohio, and I am assured by old furnace-men from Ohio that there is not the slightest difficulty it working them if properly managed. The deposits to which I wish to call the attention of the Institute,

Jan 1, 1882

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By O&apos, P. E. T. Connor

Production of petroleum in Trinidad during 1938 reached the record figure of 17,737,061 bbl., an increase of approximately two and a quarter million barrels over 1937. The principal development during the year was along the Guapo fault, which extends from Point Ligoure to Coora across the southwest portion of the island. This fault has been proved to be a major factor governing oil accumulation in the area. At the southeast end of the fault the Coora field has been actively developed during the year and already ranks as one of the major productive fields of the island. Approximately seven miles to the northwest, another richly productive area has been developed on the north side of the fault at Los Bajos, while several widely spaced wells along the fault in the intervening area suggest that the whole seven miles betwen Los Bajos and Coora will prove productive. The Penal field was placed on regular production during the early part of the year on completion of a pipe line to the Point Fortin refinery. This is a shallow pumping field with a daily output of 2000 to 1500 bbl. of heavy oil. Down-flank extension of the oil-producing structures of Forest Reserve, Kern and Point Fortin have considerably extended the proven acreages on these structures and exploitation of the deeper Cruse sands on these structures has also materially increased the known reserves. Wildcat drilling has been active in several areas. Four wells have been completed in the Mayaro district; four at Moruga; six at Cedros; six in the Morne Diable area; one at Erin and one at Point Ligoure. Few data are available from these areas, but it is understood that some cncouraging results have been obtained. In the northern basin, north of the Central Range, two locations were spudded in at the end of the year after extensive seismograph surveys. Both these locations are scheduled for depths in excess of 10,000 ft. This northern basin is entirely untested by the drill and the present drilling program is being keenly followed by all operators in Trinidad.

Jan 1, 1939

By John W. Roberts

The Federal income tax law permits as a deduction in determining net income "in the case of mines,... a reasonable allowance for depletion and for depreciation of improvements, according to the peculiar conditions in each case, based upon cost, including cost of development not otherwise deducted: Provided, that in the case of such properties acquired prior to Mar. 1, 1913, the fair market value of the property (or the taxpayer's interest therein) on that date shall be taken in lieu of cost up to that date." The law provides for a reasonable allowance but the regulations provide for a definite method of computation that possesses more the virtue of simplicity than that of reasonableness. Article 210 of Regulations 45 reads: "When the cost or value as of Mar. 1, 1913, or within 30 days after the date of discovery of the property shall have been determined, and the number of mineral units in the property as of the date of acquisition or valuation shall have been estimated, the division of the former amount by the latter figure will give the unit value for purposes of depletion, and the depletion allowance for the taxable year may be computed by multiplying such unit value by the number of units of mineral extracted during the year." This is simple, but is it reasonable? The intent of the law is clearly that the cost of the ore in the ground shall be considered as part of the cost of the same ore when removed and sold. The regulations fail to carry out that intent, because of the unwarranted assumption that all the ore in the mine cost the same amount per ton. This is what gives the Treasury Department's method its simplicity, but at the same time robs it of its reasonableness because the assumption is contrary to fact. It is self-evident that a ton of ore near the surface or exposed by present workings is worth much more than a ton buried so far down in the earth that it cannot be removed for many years. If no improvements in mining methods were expected, the value of deeply buried ore would be further reduced by the greater expense that would be required to

Jan 1, 1922

By P. E. T. Connor, O&apos

Production of petroleum in Trinidad during 1938 reached the record figure of 17,737,061 bbl., an increase of approximately two and a quarter million barrels over 1937. The principal development during the year was along the Guapo fault, which extends from Point Ligoure to Coora across the southwest portion of the island. This fault has been proved to be a major factor governing oil accumulation in the area. At the southeast end of the fault the Coora field has been actively developed during the year and already ranks as one of the major productive fields of the island. Approximately seven miles to the northwest, another richly productive area has been developed on the north side of the fault at Los Bajos, while several widely spaced wells along the fault in the intervening area suggest that the whole seven miles betwen Los Bajos and Coora will prove productive. The Penal field was placed on regular production during the early part of the year on completion of a pipe line to the Point Fortin refinery. This is a shallow pumping field with a daily output of 2000 to 1500 bbl. of heavy oil. Down-flank extension of the oil-producing structures of Forest Reserve, Kern and Point Fortin have considerably extended the proven acreages on these structures and exploitation of the deeper Cruse sands on these structures has also materially increased the known reserves. Wildcat drilling has been active in several areas. Four wells have been completed in the Mayaro district; four at Moruga; six at Cedros; six in the Morne Diable area; one at Erin and one at Point Ligoure. Few data are available from these areas, but it is understood that some cncouraging results have been obtained. In the northern basin, north of the Central Range, two locations were spudded in at the end of the year after extensive seismograph surveys. Both these locations are scheduled for depths in excess of 10,000 ft. This northern basin is entirely untested by the drill and the present drilling program is being keenly followed by all operators in Trinidad.

Jan 1, 1939

By H. S. McQueen

THE central Ozark region of Missouri has inter-ested geologists and mining engineers for many years. Of particular interest are the mineralized sink-hole type deposits, some of which have produced large quantities of iron ore. Deposits of coal are also known in this part of the State, and in mode of occur-rence are similar to the iron ore deposits. Occurring in the same general area, and often associated with coal, are deposits of high-grade non-plastic flint fire clay, and high alumina or diaspore clay. At present these clays are the most important materials being mined from the sink-hole type deposits. Deposits of high-grade flint fire clay have been known to occur in this region for many years, the Kelley pit near Rolla, Phelps County, being discovered in drilling for iron ore shortly after the close of the Civil War. Mining operations had disclosed at an early date masses of rough, open-textured "sandy" clay associated with the flint fire clay. Some of the hard flint clay also con-tained rounded shot-like particles of "sand." Both types of clay were considered of inferior grade and unsuited to the manufacture of fire brick. These clays were discarded in mining as value-less, in some instances being used for road metal. Some knowledge of the high alumina content of this sandy material had been obtained by 1908 1, and by 1917 the high alumina content was gen- erally known, and commercial shipments of what is now called diaspore clay were being made. These deposits of diaspore clay associated with flint fire clay form the only known deposits of commercial importance in North America. The production of diaspore and flint fire clay at present exceeds that of any former year. Statistics covering the production and value of the former were not collected prior to 1922, and the figures given below do not cover the tonnage of clay mined by companies and used in their own plants, so that the total produc-tion probably is much larger than that indicated. The figures were collected by the U. S. Geological Survey and the U. S. Bureau of Mines in cooperation with the Missouri Bureau of Geology and Mines.

Jan 6, 1928

By H. J. Wasson

At the close of 1927 Venezuela was producing at the rate of 205,000 bbl, per day, making it the third country in the world in point of present daily production. For the year, the total was close to 64,000,000 bbl., representing an increase of about 70 per cent. over the 37,000,000 bbl. in round numbers produced in 1926. All of the 1927 production canie from fields opened up before the beginning of the year. While no new fields were added to the list of shippers, the past 12 months' wildcatting yielded a fair quota of new discoveries which, in the light of prcsent results, may be considered likely sources of production in due time. Altogether three such promising finds were made Of first importance, at least for the immediate future, is the completion by the Lago Petroleum Corpn. of the San Matins well, 4 miles north of the present edge of the Lagunillas field. Although rated as only a 125. bbl. well, at 3217 ft., it indicates a probable extension of the field over the intervening 4 miles between the two. The two other wildcat discoveries of importance were the Los Manueles well in the District of Colon, which has in all probability opened up a new field about 7 miles north of the present Tarra oprations; and the Honibre Pintado well of the Standard Oil Co. of Venezuela,. in the State of Falcon, which is considered to be a promising clc~vc~lop~ncnt. Neither of these last mentioned two discoveries will apprcciably affect production during 1928, as the Manueles area must await the carrying out of a general plan for the exploitation of the District of Colon, a problem requiring time. The Hombre Pintado area is being tested further, but doubtless several wells will be put down before. anything definite will be done towards making the pipe line. arrangements that rnust necessarily precede the commercial exploitation of the field. The San Matias Well The San Matias well is a highly significant dcvelopment,. It is located along the trend of the La Rosa-Ilagunillas producing formations, and when drilling started, production in the Lagunillas field was 4 miles

Jan 1, 1928

By J. B. Umpleby

The function of gas in the development and production of oil has far-reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall review briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.1 They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instill into all operators an urgent desire to hasten offset drilling in order to obtain as much of the flush as possible. The most noteworthy later advance in knowledge came in 1926 when Beecher and Parkhurst published their paper on Effects of Dissolved Gas upon the Viscosity and Surface Tension of OiL.² This paper added to the old idea of an expelling force the concept of a modifying agent that actually changes the physical characteristics of the oil and facilitates its movement through the pore spaces of the reservoir rock. Largely since the publication of this paper, intensive study and concerted effort have been given to means of using to a maximum, in producing oil, these combined properties of gas. This is shown clearly by the number of papers dealing with the subject, and the new and revived terms now widely used to express thought, such as the expressions gas energy, reservoir pressure, reservoir energy, gas-oil ratio, bottom-hole pressure, beaning, tapered tubing and back-pressure. These terms, some of which are

Jan 1, 1932

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By W. C. Lacy

A WIDE variety of metalliferous deposits in Peru shows a close and consistent relationship to intrusive and extrusive igneous rocks. This relation- ship furnishes a clue to the composition of ore-bearing fluids and to the timing in separation of these fluids from differentiation magma. Conclusions presented here are based on ten years' study of a large number of metalliferous deposits in Peru. The most important of these areas are shown in Fig. 1.

Jan 5, 1957

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By C. E. Sims

THE carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example,, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath. The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner without reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature. For the carbon-oxygen reaction C + 0 [=] CO this is expressed simply as [ ] where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1947

By J. J. Gilman

Rates of prisnzatic plastic glide ( {1010}<2110>) in pure Cd crystals have been measured at temperatures from 158° to 276°C. The glide rate is proportional to the 2.75 power of the applied shear-stress. The activation energy is 29.2 kcal per mol. It is suggested that the rates of prismatic glide in Cd and Zn crystals are determined by the strengths of the atomic bonds across the prism planes. ALTHOUGH zinc and cadmium crystals both have hexagonal structures with nearly the same c/o ratios, their mechanical behaviors are quite different. Whereas zinc becomes quite brittle below room temperature, and cleaves readily on (0001) planes, cadmium is very ductile even at 4.2°K, and cannot be cleaved at any temperature. As part of a search for the explanation of this difference in behavior, a study has been made of prismatic glide in cadmium. It complements a previous study of the same phenomenon in zinc.1 The primary glide plane in cadmium is the basal (0001) plane, and the primary glide direction is the direction of atomic close-packing <2110>. However, if a tensile stress is applied parallel to the basal plane, then the shear stress on the basal plane equals zero so basal glide cannot occur. At low temperatures, deformation by twinning occurs; but at high temperatures, it has been found in this study that gliding on prismatic planes (1010) occurs in the close-packed direction. This is completely analogous with the case of zinc, except that lower temperatures are required. EXPERIMENTAL The experiments were done in nearly the same way as for zinc.&apos; Therefore, only the differences in the two sets of experiments will be described here; for other details the reader is referred to the previous paper. Crystals 6 by 6 mm sq were used that were grown from "Super Purity" 99.999 + pct Cd purchased from the New Jersey Zinc Co. The crystals were grown with their basal planes parallel to both the rod axis and one of the flat sides of the square cross section, A close-packed direction in the basal plane was oriented parallel to the rod axis. Gage sections were carefully machined into the crystals, and the surface damage caused by machining was removed with the same chemical polishing reagent as had been used for zinc. Thus, specimens of the same form and size as the previous zinc ones were produced. The crystals were heated to the test temperatures in a silicone oil bath (fused salts were tried first, but they reacted badly with the cadmium). An Instron tensile-testing machine was used for applying stresses to the crystals at various constant strain-rates. RESULTS The general behavior of cadmium crystals is much the same as for zinc. Only the constants that measure specific properties are different. Just as

Jan 1, 1962