Search Documents

ALTHOUGH the open-hearth charge contributes CO, C02, H2, A and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required, for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In, any event, this requirement appears. small in comparison with the

Jan 1, 1964

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By H. M. Morse

During the year of 1940, wildcat wells were drilled in 32 counties of Mississippi; 85 wells in all. These were scattered over the state from the most northern county to the southern counties and from the Mississippi River on the west to the Alabama line on the east. Yazoo County, with 19, received the largest number. The average depth of all the wells was 5333 ft. The shallowest well completed as a dry hole was in Yalobusha County, aban-doned at 1392 ft. in the Selma. The deepest well drilled was in Scott County, abandoned at 10,365 ft. in the Lower Cretaceous Paluxy. G. C. Grasty drilled the Kentucky Lumber Company No. I well, sec. 7, T. 10 S., R. 10 E., Itawamba County, to a depth of 3530 ft. and bottomed his hole in the Ordivician. Tinsley Oil Field.—In the Tinsley oil field 104 wells were completed as producers during 1940. Five producing sands have been logged with a total average thickness of I57 ft. of oil sand. One of these sands is in the Selma, three in the Eutaw, and one in the Tuscaloosa. Vaughan-Pickens Field.—The Vaughan-

Jan 1, 1941

By H. M. Morse

During the year of 1940, wildcat wells were drilled in 32 counties of Mississippi; 85 wells in all. These were scattered over the state from the most northern county to the southern counties and from the Mississippi River on the west to the Alabama line on the east. Yazoo County, with 19, received the largest number. The average depth of all the wells was 5333 ft. The shallowest well completed as a dry hole was in Yalobusha County, aban-doned at 1392 ft. in the Selma. The deepest well drilled was in Scott County, abandoned at 10,365 ft. in the Lower Cretaceous Paluxy. G. C. Grasty drilled the Kentucky Lumber Company No. I well, sec. 7, T. 10 S., R. 10 E., Itawamba County, to a depth of 3530 ft. and bottomed his hole in the Ordivician. Tinsley Oil Field.—In the Tinsley oil field 104 wells were completed as producers during 1940. Five producing sands have been logged with a total average thickness of I57 ft. of oil sand. One of these sands is in the Selma, three in the Eutaw, and one in the Tuscaloosa. Vaughan-Pickens Field.—The Vaughan-

Jan 1, 1941

By L. N. Cosner, C. F. Austin, J. K. Pringle

Shock wave attenuation studies with three igneous rocks are reported: a spessartite elastic to low intensity stress waves, a diorite which is anelastic, and a porous scoria. The level of shock passing through a given thickness of rock has been determined by donor-receptor methods using high speed streak cameras. Test results include shock propagation velocities adjacent to the explosive, the dependence of test results upon test geometry, and the variation in shock wave attenuation in these three common igneous rock fabrics. The utilization of explosives in rock mediums involves a series of interrelated phenomena. These are the detonation process within the explosive, the transfer of energy from the explosion products to the surrounding rock medium in the form of sound or shock waves, and the transmission of the resulting waves through the rock medium to create damage in the rock mass. The subject of this paper is the investigation of the close-in phenomena that occur in the intensely shocked rock immediately adjacent to a detonating explosive charge. The specific aspects studied include propagation velocities, free surface velocities, pulse attenuations and the determination of the equations of state for the test rocks employed. In addition, a series of tests was conducted to indicate the dependence of the test results on the charge diameter utilized. The equations of state for rock materials have been investigated by a number of authors. Lombard, &apos;,&apos; Grine and Fowles,3,4 Zharkov, 5 Hughes and McQueen,6 Chabai,7,8 and Bass9 have published equation of state data on rock materials similar in structure or composition to those investigated in the study. Rinehart10 has prepared a voluminous tabulation of the available equation of state data from these publications and in addition has included data on many other rock and earth materials in his compilation. The reader is referred to the extensive tabulations and bibliography of Rinehart for classical studies involving the equations of state of metals and other solids and liquids. The problems of sympathetic detonation between drill holes in hard rock environments has received the attention of various authors as have the problems of explosive rock coupling close-in stress wave attenuation and explosive diameter effects. 11 to 18 In particular, the don or-receptor geometry of this report is very similar to the geometry of adjacent drill holes in rock. Most published pulse velocity and attenuation work in rock has been devoted to velocities at much lower amplitudes than those associated with close-in explosives phenomena and most attenuation studies involve transmission and attenuation across large spans of material. Excellent work in these areas has been published by the U. S. Bureau of Mines and by many individuals and groups engaged in geophysical research. SELECTION OF TEST MATERIALS A series of rock materials was desired for this test program that would be meaningful industrially, and that would also yield comparative results from a research viewpoint. Based on the availability of a series of related petro-fabrics, for which there is an abundance of physical and shock response data, three igneous rocks were selected as the test series. The applicability of shock wave studies in igneous rocks to industrial problems is readily demonstrated. Hardrock tunneling, quarrying and mining take place in igneous rocks throughout the world. From a research point of view, igneous rocks exhibit a wide variety of grain sizes and considerable diversity in composition, yet the common igneous rocks have a general similarity in their constituent mineral structures and in their grain-to-grain bonding mechanisms. The latter is based on the concept of rock formation through magma cooling and crystallization, though the degree of liquefaction in granitic plutonic masses is indeed a moot question. Three specific types of igneous rock were chosen for study. A coarse-grained granitic textured rock was desired that would serve as a representative of the widely abundant intrusive rocks of the world and

Jan 1, 1967

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.&apos; Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By F. Paredes, W. R. Holman, R. W. Crawford

The diffusion coefficient for hydrogen in the ß titanium alloy containing 13 pct V, 11 pct CY, and 3 pct A1 was measured over the temperature range 20° to 500°C. Results fit the expression: D= 1.58 x lgs exp-------==-----) cm2,sec THE diffusion coefficient for hydrogen in the metastable ß-phase titanium alloy containing 13 pct V, 11 pct Cr, and 3 pct A1 was measured as part of an investigation of the effects of hydrogen on the mechanical properties of titanium alloys. Several theories on the mechanisms of hydrogen embrittle-ment include diffusion of hydrogen at ambient temperature as an important step in the embrittling process.&apos;-5 In hydrogen-contaminated a-ß titanium alloys, it has been postulated that the rate-controlling step may be the rate at which hydrogen diffuses from the ß phase to stress- or strain-nucleated brittle hydride platelets at the a-ß interface.&apos; However, embrittlement of the all-ß alloy investigated in this work may proceed by a different mechanism, since this alloy can be embrittled without the formation of detectable hydride platelets.6 Troiano has suggested that in this case the mechanism of delayed failure or embrittlement is similar to that proposed for high-strength steel, i.e., repeated crack initiation caused by a decrease in bonding energy as hydrogen diffuses to points of high tri-axial stress at the root of a notch. In both types of alloy the rate of embrittlement is believed to be controlled by diffusion of hydrogen in the ß phase. Accurate hydrogen-diffusion data in the vicinity of room temperature should therefore be of some assistance in understanding the mechanisms of embrittlement in these two classes of titanium alloys. Diffusion of hydrogen in pure titanium has been studied by Wasilewski and Kehl7 at temperatures above 500°C. Their measurements on diffusion in the ß phase were extended below the ß-a transformation temperature (882°C) to approximately 600°C. This was possible because of the 8 stabilizing effect of hydrogen. No results at lower temperatures have been published and there are no data in the literature on hydrogen diffusion in the ß -phase alloy used in this program. Hydrogen diffusion in metals is generally investigated by measuring the rate of transport of hydrogen past a solid-gas interface, i.e., by absorption, permeation, or degassing-rate measurements. These methods produce accurate diffusion data when bulk diffusion is the rate-determining step in the over-all process. However, at the lower temperatures of interest in hydrogen-embrittlement studies or under conditions where surface films are present, the measured rates may be surface-controlled and the calculated diffusion coefficients will be in error. Surface effects were eliminated in the present work by using a modification of the common welded-couple technique m which two bars with uniform but different compositions are joined before the diffusion anneal." The same type of step change in the initial concentration vs distance curve was produced by electrolytically hydrogenating thin-strip specimens which had been electrically insulated over half of their length. Concentration vs distance curves were determined, after appropriate diffusion-annealing treatments, by vacuum-extraction analyses of transverse samples sheared from the strips. Diffusion coefficients were calculated by the methods of Grube.M This technique was feasible because of the large concentrations of hydrogen which can be charged into p -phase alloys without the formation of hydrides15&apos;16 and because of the extremely low degassing rates observed when hydrogenated titanium alloys are heated in air. EXPERIMENTAL WORK The diffusion couples were cut from a 0.022-in.-thick mi ll-annealed sheet.* Strips 8 in. long by 1/2

Jan 1, 1965

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Herbert M. Wilson

We of the employer class represent labor in the social organization and in industry just as truly as do those who labor only with their hands, and, because our labor is chiefly with our brains, the duty is all the more imposed upon us to use those gifts in which we excel in helping steer a clear course through the turbulent waters in which we are now enmeshed. Only their selfish engrossment in the daily tasks they were employed to perform could possibly have permitted the great majority of the intelligent and industrious German people to become terrorized by a handful of the idle, the vicious, and the criminal, whom the elections to the National Assembly showed to be in as pitiful a minority as they are in Russia, in this, and in other countries. It is the leisure unemployment of the I.W.W.&apos;s, the Bolsheviki, and the Sparticans that has enabled them to devote their whole time to a concerted and aggressive struggle against the great majority of those of the world&apos;s workers who are unorganized, and who are therefore even in opposition one to the other. In union there is strength, and this was never better illustrated than by these conditions. The great fallacy of our previous attitude toward social and industrial problems has been the belief that labor, by which we commonly mean organized or physical labor, is something antagonistic to and having a different object in life from that great body of unorganized laborers who work with their brains. Our difficulty has been our lack of will or opportunity to think. The hurry of our daily struggle to earn our livelihood under the nerve-racking pressure of modern civilization has left us no opportunity for quiet thought and study. The physical laborer, and above all the laborer in the mines, on the other hand, has all his hours of toil in which to think over, in all their varied aspects, those problems that concern his immediate, personal well-being. As a result he has arrived at perhaps a more true appreciation of the facts of life in their relation to social and industrial conditions than we. Have we not too readily adopted the view that, as the managers of industry under the direction of capital, it has been our duty to think and act in opposition to labor, rather than to realize that we also are laborers, have like aspirations, and should participate in a free and aggressive solution of these problems rather than leave their solution

Jan 1, 1919

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130ºF. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By Rodney P. Smith

The diffusivity of carbon (0.1 wt pct C) in Fe-Nz alloys (0 to 100 pct Ni) has been determined for the temperature range 860° to 1100°C. As a function of nickel content, the diffusivity has a maximum near 60 pct Ni (the maximum diffusivity being about 1.3 times that in the absence of nickel); the activation energy has a maximum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The difference between the minimum activation energy and that in iron is about 3000 cal pev g-atom; Do has a minimum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The results cannot be rationalized by an approximate thermodynamic treatment. THE diffusivity of carbon has been determined in a number of iron alloys over a limited concentration range. It seemed desirable to investigate a system which allows an extended range of alloy composition within a single-phase region. The Fe-Ni system is ideal in this respect, in that all alloys from 100 pct Fe to 100 pct Ni are fee in a convenient temperature range.&apos; The carbon diffusivity was determined by a decar-burization method. The experimental procedure was identical with that used to determine the diffusivity of carbon in y Fe-Co alloys.2 The experimental data are given in Table I. A small correction (order of a few percent) has been made to the measured carbon loss to correct for the carbon lost from the ends of the cylinders.&apos; Since the diffusivity of carbon varies with carbon content the measured diffusivity is an average value for a carbon content between zero (surface) and that at the center of the sample at the end of the decarburization periods. In making the correction in D to 0.1 wt pct C it is assumed that the measured D corresponds to the arithmetical mean of the carbon content at the surface and at the center of the sample at the end of the decarburization period.3 Since this correction is small (<4 pct in D) and since for our decarburization times the changes in carbon content at the center of the sample was small the mean carbon content could have been taken as half the initial value. It is further assumed that the change in D with carbon content for the alloys is the same as that for the diffusion of carbon in iron. From the data of Wells, Batz, and Mehl4 and of smith5 the correction of D from the mean carbon content to 0.1 wt pct C is 0.3 (0.1 - mean wt pct C). The results for iron are given in Ref. 2. Within the experimental error log Do.l%C for each alloy is a linear function of 1/T; the constants for the equation determined by the method of least squares are given in Table I. The deviations of the experimental points from the least-squares line are of the order of 2 pct in D. A comparison of our results for the diffusivity of carbon in nickel with those of other investigations is shown in Fig. 1. The lower curve in Fig. 1 is a linear extrapolation of values calculated* from the equation of Diamond6 for the relaxation time (temperature range 100° to 500°C). The results indicate a small increase in the activation energy over the temperature range 100° to 1400°C; however, it is difficult to say whether the change in Q is real or experimental error. Certainly the change in Q is less than the variation of 5 kcal per g-atom in the diffusivity of carbon in a iron.6 The experimental data for all the alloys are plotted in Fig. 2. As a function of nickel content the diffusivity has a maximum near 60 wt pct Ni at all temperatures investigated and possibly a minimum between 80 and 90 wt pct Ni for temperatures below 1000°C. The activation energy, Q, and log Do are plotted as a function of the nickel content in Fig. 3. Due to the limited temperature range of our experiments neither Q nor Do can be determined precisely; the activation energies appear to be consistent to ±0.3 kcal per g-atom; however the deviation from the absolute values may be considerably larger, see Table II. The Do values probably have little significance. The solid line for Do in Fig. 3 represents the values required to reproduce the experimental values for D when Q has values represented by the upper solid line The diffusivity of carbon may be expressed in terms of the mobility B22, the activity coefficient r2,

Jan 1, 1967

By D. S. Greig

There was a decline in the Italian oil production in 1933 and also in the footage drilled. A total of about 194,500 bbl. of crude oil was produced in the Emilia district of northern Italy from the same fields in production as in 1932. New drilling to the extent of 80,700 ft. failed to find new production to compensate for the decline in old wells, and no new fields were discovered in spite of an active exploration campaign by the government-owned company A.G.I.P., which has just completed the first year of a five-year exploration program. This company drilled a total of about 33,000 ft. The majority of its tests were drilled in the Po Valley upon locations selected by geophysical methods. This company is changing over to the rotary system for all future wells. It produced about 16,600 bbl. of oil from wells near Salsomaggiore and in the Po Valley. The Petroli d&apos;Italia, which operates the old fields of Montechino, Valleja and Gratera south of Piacenza, has been doing normal development drilling in the endeavor to extend its present fields. Also it was drilling two exploration wells in the Torino district. It drilled a total of about 13,930 ft. and produced approximately 12,645 bbl. of very high-grade oil (specific gravity about 0.765). The Societa Petrolifera Italiana was occupied chiefly in exploratory drilling in the endeavor to extend its producing fields at Salsomaggiore and at Vallezza, south of Parma. It was also drilling one exploration well at Rile dell7Olio near Voghera on the line Milan-Genoa. It drilled a total of 33,849 ft. and obtained a production from its two fields of 165,273 bbl. It also produced 123,220 gal. of casinghead gasoline from Vallezza field absorption plant.

Jan 1, 1934

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-&apos; and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

By Klaus Schwerdtfeger

The rules of solution of oxygen from H2O-H2-He gas and of nitrogen from N2-H2 gas in shallow melts of liquid iron were measured at 1610o and 1600o C, respectiuely. Concentration profiles were detemined in the liquid iron. Tire rate data indicate that the solution process is controlled by diffusion in the iron melt. The diffusivities for oxygen and nitrogen in liquid iron, as calculated from the present data, are DFe-o = (12 ± 3) < 10-5 sq cm per sec and DFe-N = 11 ± 2) X 10-5 sq cm per sec at the temperatures employed. AN attempt was made by Shurygin and Kryukl to measure the diffusivity of oxygen in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was measured. Assuming that the rate of dissolution of silica is controlled by diffusion of oxygen in the iron, the oxygen diffusivity was computed from the rate data giving Dfe-0 = 6.1 X 5 sq cm per sec at 1600°C. Although this value seems to be of the right order of magnitude, there is no proof of the correctness of the assumptions involved in the interpretation of these rate data. The oxygen concentration in the iron at the iron-iron silicate interface was taken to be that in equilibrium with the silica-saturated silicate melt. That is, it was assumed that no concentration gradient existed in the liquid silicate. This is a questionable assumption, unless it is proved that the thickness of the silicate layer is very much smaller than that of the diffusion boundary layer in the iron. Furthermore, Shurygin et al.1 used the Levich equation2 to interpret their rate data. This equation was derived for mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s derivations. In the present work the diffusivities of oxygen and nitrogen in liquid iron were measured at 1610" and 1600oC, respectively. EXPERIMENTAL METHOD Iron melts contained in high-purity gas-tight alumina crucibles were reacted with H2O-H2-He gas for the determination of the oxygen diffusivity and with N2-H2 gas for the determination of nitrogen diffusivity. At the end of the reaction period, the samples were quenched in a cold H2-He gas stream at the top of the furnace. Oxygen or nitrogen contents in the iron were determined by chemical analysis. Two different types of diffusion experiments were perforxed. To determine concentration profiles, a few rate measurements were made using 4-cm-deep melts. The solidified samples were sliced into discs and each disc was analyzed for oxygen or nitrogen. In another series of experiments, oxygen or nitrogen was diffused into shallow melts (about 0.5 to 1 cm in depth) and the total sample was analyzed to obtain an average concentration of the diffusate. In most experiments, 4- to 5-mm-ID alumina crucibles were used. Some experiments were also made in smaller (3 mm) and larger (7 mm) diam crucibles. This variation in diameter caused no difference in the reaction rate, within the limits of experimental uncertainty. To promote the establishment of a stable density profile in the melt, all the samples were suspended in the lower end of the hot zone so that the top of the melt was hotter by a few degrees. Molybdenum wire resistance heating was used. The reaction tube of the furnace was a gas-tight recrystal-lized alumina tube. In most experiments the furnace was heated by an ac power supply. To check the possibility of inductive stirring, some experiments were carried out in a dc operated furnace, with essentially the same results. The temperature of the furnace was controlled automatically in the usual manner. The temperature was measured with a Pt/Pt-10 pet Rh thermocouple and is estimated to be accurate within ±5°C. The iron used was prepared by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zir-conia crucible. The main impurities are: Si 0.004 pct P, S <0.002 pct Cr 0.005 pct N 0.001 pct Zr 0.002 pct O 0.003 pct Mn 0.004 pct C 0.002 pct The gas composition was controlled by constant pressure head capillary flowmeters. Oxygen was removed from the gas mixture by passing it through columns of platinized asbestos (450°C) and anhydrone. Selected H2O contents were obtained by passing the purified gas through oxalic acid dihydrate-anhydrous oxalic acid mixtures held at constant temperature in a water bath. Water vapor pressure data for the oxalic acid dihydrate-anhydrous oxalic acid equilibrium were taken from the 1iterature.3 The flow rate used was about 1.5 liters per min. The whole system was checked for tightness at regular intervals.

Jan 1, 1968

By Ancel St. John

At the New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,&apos; in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papcrs which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangc-mcnts were therefore made to present that evidence at this meeting. Material Examined The material exalllined was high-ernission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. Scope of the Investigation The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of t.horia detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By P. V. Roundy, G. R. Mansfield

PUBLIC lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey&apos;s usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. COMMERCIAL PROSPECTING METHODS Commercial methods of prospecting for phosphate in Florida have been briefly described by Mansfield.1 In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill as

Jan 1, 1937

By Edward L. Estabrook

This paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: Barrels Barrels 1915.................... 94,073.5 1918................... 2,946,774.27 1916................... 1,404,183.97 1919................... 2,000,584.84 1917.................... 2,780,697.51 1920................... 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep, have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field. The principal producing sands in the field are members of the Frontier Formation, a series of sands and shales occuring in the upper portion of the Colorado Group of the Upper Cretaceous seriee. These Frontier, or "Wall Creek" sands are also productive in the Salt Creek, Big Muddy, and Elk Basin fields and, therefore, are much the most important reservoirs of light oil in Wyoming. At Grass Creek, the sands in the Formation are more numerous than in the other fields and much less uniform in thickness and character. Usually, eight distinct beds are encountered and in some wells twelve sands have been reported. The formation above

Jan 1, 1923

By Paul R. Martin, R. B. Kelly

The area comprising what is geographically termed "Central Texas" was somewhat less active in 1934 than in 1933. The year saw the completion of 182 dry holes and only 74 producing wells. Bexar, Williamson and Bastrop counties, with active fields such as Yturri-Southton, Byersville, North Dale and Cedar Creek contributed a majority of the new oil wells. Hilbig, in Bastrop County, 1933&apos;s most important discovery in the district, saw no development during the current year. New fields opened in 1934 were Byersville, a serpentine intrusion in Williamson County, and Manda, producing from similar material in Travis County. Like most of the other serpentine plugs, neither gives promise of covering a very large area. Other active counties were Bexar, Bastrop and Caldwell, although successful operations in each of them were limited to the old fields. The location of producing fields is shown on Fig. 1. New Fields Byersvil1e.—Late in 1933, Fritz Fuchs completed Zeischang No. 1, eight miles south of Taylor, Williamson County, for an initial production of 25 bbl. per day. The oil is 37" B6. A.P.I. gravity and is from Serpentine formation at approximately 900 ft. Additional drilling was carried on in 1934, and at the end of the year 18 producing wells had been completed, proving about 200 acres. Manda.—The Manda field, or Kimbro field as it is termed by some, received its first production Sept. 10, 1934, when the Humble Oil & Refining Co. completed No. 1 C. J. Peterson as an 8-bbl. oil well. The new field is near Littig, in eastern Travis County, and is about 15 miles northeast of Austin. Production is found in serpentine formation between 650 and 750 ft. The same company&apos;s No. 1 Buck Christian, second well in the field, flowed 190 bbl. per day through a ?-in choke. Although only a small area has been definitely proven it is expected that present drilling will provide extensions in several directions.

Jan 1, 1935

By Edward L. Estabrook

This paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: Barrels Barrels 1915.................... 94,073.5 1918................... 2,946,774.27 1916................... 1,404,183.97 1919................... 2,000,584.84 1917.................... 2,780,697.51 1920................... 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep, have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field. The principal producing sands in the field are members of the Frontier Formation, a series of sands and shales occuring in the upper portion of the Colorado Group of the Upper Cretaceous seriee. These Frontier, or "Wall Creek" sands are also productive in the Salt Creek, Big Muddy, and Elk Basin fields and, therefore, are much the most important reservoirs of light oil in Wyoming. At Grass Creek, the sands in the Formation are more numerous than in the other fields and much less uniform in thickness and character. Usually, eight distinct beds are encountered and in some wells twelve sands have been reported. The formation above

Jan 1, 1923