Search Documents

By S. E. Maddigan

MANY experimental and theoretical investigations have been made on the processes involved in annealing and recrystallization of metals. Most of these, however, have treated the time element as constant and heat-treatments used have been for relatively short times. Aside from the early work by Carpenter and Elam,1 the few that have investigated the effect of time on the processes have usually done so for fairly short time periods. During recent years the growing interest in long-time creep properties of metals and alloys under stress has made increasingly important a better knowledge of the recrystallization during prolonged heating. The recrystallization temperature of 70-30 brass given by Clark and White2 in 1932 was somewhat above 400°F. (204°C.) but under 500° (260°C.), whereas in our laboratory recrystallization has been observed in creep specimens at 204°C, the lowest temperature of Clark and White's range. Since the creep properties are quite different above and below the recrystallization temperature, erroneous conclusions can readily be drawn by the application of short-time recrystallization data to creep problems. It was thus considered of both practical and theoretical value to make long-time annealing studies near the minimum recrystallization temperature. In this way useful additions could be made to data on recrystallization temperatures and, since the reactions in this range are relatively slow, additional insight could be obtained into the factors involved in annealing. Several comprehensive reviews of recrystallization processes have been written,3-5 therefore only a brief review of the generally accepted facts will be given here.

Jan 1, 1940

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of&apos; the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.&apos;,&apos; The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of&apos; the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.&apos;,&apos; The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By Beverley S. Randolph

While our coal-mining practice, in regard to hauling on main roads, has advanced very rapidly in recent years by means of compressed air, electricity and ropes, that of gathering from rooms or working-places has remained almost stationary. Few large mines are without some method of mechanical haulage on main roads, but the gathering from working-places is still done almost entirely by means of animals or men. An effort to improve this has been made recently by the Consolidation Coal Company, under the direction of the writer, at its mines in the Georges Creek region. The seam worked is the Pittsburg bed, known locally as the " Big Vein." It is from 8 to 12 feet thick. Immediately overlying the coal there is from 5 to 6 feet of " rashings," consisting of thin alternating beds of shale and coal, which disintegrate rapidly on exposure to the air, and making a very treacherous roof. Rooms are driven from 12 to 15 ft. wide, with a single track close to one side. A line of posts is placed just far enough from this side to leave a clear space for the mine-car with a driver at the brake. This brings the post not far from the middle of the cross-bar, and provides more effectual support than if placed at the end. The tracks in these rooms are usually of 4 in. x 4 in. oak scantling, though of late years, owing to the advance in the price of lumber and the reduction in steel rails, more of the latter are being used. This track is laid by the miner. His pay for the work is included in the price per ton for mining. It is therefore, as a rule, unskillfully and often carelessly laid, and cannot be relied upon to carry safely any weight materially greater than the loaded mine-car. Compressed air was already in use on the main roads, driving motors weighing 30,000 pounds each, which were used to. bring the mine-cars that had been assembled from the rooms

Jan 1, 1904

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of &apos;quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By Michael J. Messel

W. P. MOULD*—Has consideration been given to the problem of retreating the 4,000,000 ton tailings pile to recover the very considerable amount of asbestos fiber that was lost over the years due to insufficient operation and poor recoveries? Also, what was known about the possible content of chromite and the sulphides of nickel and cobalt? M. J. MESSEL (author&apos;s reply)—Consideration was given to the problem but nothing concrete has been done up to this time. W. P. MOULD—I am certain the tail- ings contain a very considerable quantity of fiber, not all of which is in the shortest lengths, because in the milling of talc rock from a neighboring location having a common origin with the asbestos bearing serpentine source of the tailings pile, a concentrate carrying 15 pct Ni and Co in complex sulphides and constituting about 4/10 of 1 pct of the talc rock was recovered. In the belief that the tailings also contained an appreciable content of chromite (then in demand, 1937) it was suggested to the management of the asbestos company that a truck load of the current tailings be sent to the flotation plant of the talc company where it would be put over the concentrating tables in an effort to discover the presence and roughly the percentages of chromite, nickel, and cobalt. Preparations for the test were woefully inadequate and the test was completely snarled up by the surprisingly large quantity of asbestos fiber from 1 in. long down to very short fiber, all of which matted up and plugged launders and pumps with disastrous effects and practically the total loss of the sample. If anything was indicaded by the test, it was that a wet process for milling asbestos was worthy of very serious consideration. M. J. MESSEL—A wet milling process for tailings retreatment only, is at present under study at our plant. One asbestos mining company in Canada has constructed a fairly large test plant for this purpose, but as yet no definite results have been obtained other than in a small test unit plant which were in some respects quite encouraging.

Jan 1, 1950

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919

By G. E. Frantti

UNDER the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan&apos;s Upper Peninsula to obtain geophysical data" related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilsonz near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula. Early in the 1900&apos;s the Michigan Geological Survey, as well as many private companies, had done a considerable amount of dip needle work near the southwest corner of the area discussed in this paper. Most of the information available to the writer was obtained from indicated magnetic anomalies on the geological map of the northern peninsula of Michigan. Results of the geophysical activities of mining companies in the vicinity of the Marquette range and Gwinn district were unavailable to the author. Physiography and Geography: The region under consideration has low to moderate relief. About half the area is comprised of swampy lowlands, and because of the swamps and forests much of the land is almost inaccessible. The major drainage system is dendritic, with streams flowing into Lake Michigan on the south and Lake Superior on the north. The general geology, shown in Fig. 2, indicates an overlay of Paleozoic sediments on pre-Cambrian formations along a line running approximately south from Marquette (not shown on the geological map). Actual contact between pre-Cambrian and Paleozoic sediments is not known because most of the area is covered with glacial till, and outcrops are very scarce. Exposures of the Paleozoic sediments show that these beds in the northern areas dip gently under Lake Superior and that in the southern areas they &apos;dip gently to the southeast. Outcroppings of the pre-Cambrian formations occur primarily to the west of the surveyed area except in the northwest corner where the Laurentian series outcrop as far east as the Gwinn district and also in T46N, R24W. Instrumentation: Gravity measurements were made with the Worden portable gravity meter. Since this was chiefly a reconnaissance regional survey, both the large and small dials were used. The instrument used had a constant of 0.0035 milligals per scale division, a working range of about 25 milligals.

Jan 1, 1957

By William D. Klopp, Joseph R. Stephens

A substantial reduction in the 300°F ductile-to-brittle transition temperature for unalloyed chromium was achieved in alloys from systems which resemble the Cr-Re system. These alloy systems include Cr-Ru, Cr-Co, and Cr-Fe. Transition temperatures ranged from -300° F for Cr-35 at. pct Re to -75°F for 0-50 at. pct Fe. The ductile alloys have high grain gvowth rates at elevated temperatures. Also, Cr-24 at. pct Ru exhibited enhanced tensile ductility at elevated temperatures, characteristic of superplas-ticity. It is concluded that phase relations play an importarlt role in the rhenium ductilizing effect. The ductile alloys have compositions near the solubility limit in systems with a high terminal solubility and which contain an intermediate o phase. The importance of enhanced high-temperature ductility to the rhenium ductilizing effect is not well understood although both may have common basic features. CHROMIUM alloys are currently being investigated for advanced air-breathing engine applications, primarily as turbine buckets and/or stator vanes. The inherent advantages of chromium as a high-temperature structural material are well-known1 and include its high melting point relative to superalloys, moderately high modulus of elasticity, low density, good thermal shock resistance, and superior oxidation resistance as compared to the other refractory metals. Additionally, it is capable of being strengthened by conventional alloying techniques. The major disadvantage of chromium is its poor ductility at ambient temperatures, a problem which it shares with the other two Group VI-A metals, molybdenum and tungsten. For chromium, the problem is further amplified by its susceptibility to nitrogen em-brittlement during high-temperature air exposure. In cases of severe nitrogen embrittlement, the ductile-to-brittle transition temperature might exceed the steady-state operating temperature of the component. The low ductility of chromium would make stator vanes and turbine buckets prone to foreign object damage. The present work was directed towards improvement of the ductility of chromium through alloying, with the anticipation that any improvements so obtained might be additive to strengthening improvements achieved through different types of alloying. The alloying additions for ductility were selected on the basis of the similarity of their phase relations with chromium to that of Cr-Re. The reduction in the ductile-to-brittle transition temperatures of the Group VI-A metals as a result of alloying with 25 to 35 pct Re is well established.a4 the temperature range -300" to 750° F. This phenomenon is commonly referred to as the &apos;<rhenium ductilizing effect"; this term is also used to describe systems in which the ductilizing element is not rhenium. Other alloy systems which have recently been shown to exhibit the rhenium ductilizing effect include Cr-Co and c-Ru.= In order to explore the generality of this effect, alloys were selected from systems having phase relations similar to that of Cr-Re, primarily a high solubility in chromium and an intermediate o phase. The following compositions were prepared: Cr-35 and -40Re; Cr-10, -15, -18, -21, -24, and -27 pct Ru; Cr-25 and -30 pct Co; Cr-30, -40, and -50 pct Fe; Cr-45, -55, and -65 pct Mn. Seven other systems were also studied which partially resemble Cr-Re. These systems have extensive chromium solid solutions or a complex intermediate phase, not necessarily o. The compositions evaluated include the following: Cr-20 pct Ti; Cr-15, -30, and -45 pct V; Cr-2.5 pct Cb; Cr-2.5 pct Ta; Cr-20 pct Ni; Cr-6, -9, -12, and -15 pct 0s; Cr-10 pct Ir. The compositions of alloys in these systems were chosen near the solubility limit for the chromium-base solid solutions, since in the Group VI-A Re systems, the saturated alloys are the most ductile. These alloys were evaluated on the basis of hardness, fabricability, and ductile-to-brittle transition temperatures. In addition to the studies of alloying effects on ductility, an exploratory investigation was conducted on mechanical properties at high temperatures in Cr-Ru alloys EXPERIMENTAL PROCEDURE High-purity chromium prepared by the iodide deposition process was employed for all studies. An analysis of this chromium is given in Table I. Alloying elements were obtained in the following forms: Commercially pure powder — iridium, osmium, rhenium, and ruthenium. Arc-melted ingot — titanium and vanadium. Electrolytic flake — iron, manganese, and nickel. Sheet rolled from electron-bearn-melted ingot — columbium and tantalum. Electron-beam-melted ingot — cobalt. Sheet rolled from arc-melted ingot — rhenium. All alloys were initially consolidated by triple arc melting into 60-g button ingots on a water-cooled hearth using a nonconsumable tungsten electrode. The melting atmosphere was Ti-gettered Ar at a pressure of 20 torr. The ingots were drop cast into rectangular slabs and fabricated by heating at 1470" to 2800° F in argon followed by rolling in air. Bend specimens measuring 0.3 by 0.9 in. were cut from the 0.035-in. sheet parallel to the rolling direction. The specimens were annealed for 1 hr in argon, furnace cooled or water quenched, and electropolished prior to testing. Three-point loading bend tests were conducted at a crosshead speed of l-in. per min over

Jan 1, 1969

By H. N. Hickey

Wildcat drilling operations in Montana during 1933 did not yield any discoveries of oil or gas that were of major importance. There was comparatively little drilling in the older proven fields, as most of the interest was centered in the Cut Bank field, where 44 wells were completed. The total number of wells completed in the state during the year was 79, of which 62 were productive of either oil or gas.

Jan 1, 1934

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm&apos;3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.&apos; The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By R. M. Waterstrat, B. N. Das, Paul A. Beck

The central region of the Ti-Mn system was studied by means of x-ray diffraction and metallography. The following intermediate phases were found: an MgZn2-type Laves phase having a wide range of homogeneity, the p-phase of unknozvn structure, and the + -phase with a large tetragonal unit cell, stable at 930°C and lower temperatuves. MaYKUTH, Ogden, and jaffee1 determined the soh-inh bility limits of manganese in and titanium. They also confirmed the structure of the intermediate phase TiMn2 which was previously identified as a Laves phase of the MgZn2 type.2 In the equiatomic region they found an additional intermediate phase, y, which presumably formed by a peritectic reaction at approximately 1200°C. This last observation was disputed by Rostoker, Elliott, and McPhers0n,3 who reported the formation of TiMn by a peritectoid reaction between 900" and 1000° C, but found no evidence of any intermediate phase other than the Laves phase at higher temperatures. Elliott and Rostoker4 reported furthermore that the X-ray diffraction pattern of TiMn could be identified as that of a o phase, although their data were not consistent with this inter~retation. Margolin and Ence6 presented X-ray diffraction data for the and TiMn, phases, and obtained metallographic indications for the existence of additional intermediate phases. They concluded from metallographic observations that two Laves phases are formed, separated by another phase, designated as &. A phase diagram for the Mn-Ti system has recently been published by Savitskii and Kopetskii,&apos; which shows considerable disagreement with the work of Hellawell and Hume-Rothery,&apos; in particular with regard to the terminal solid solutions based on the allotropes of manganese. The present investigation was undertaken primarily to clarify the phase relationships in the equiatomic region of the Ti-Mn system. The metals used in preparing the alloy specimens Were iodide titanium and electrolytic manganese, the latter having a nominal purity of approximately 99.9 pet. The electrolytic manganese was covered with a thick coating of a brown manganese oxide which was reduced by heating the manganese flakes for several hours at a temperature of 1100°C in an atmosphere of dry hydrogen. Three alloys, see Table I, were made using sponge titanium and manganese not treated in hydrogen. The alloys were prepared by arc-melting in an atmosphere of helium or argon. The composition of each alloy was calculated by assuming that the entire weight loss during melting was due to evaporation of manganese. Subsequent chemical analysis of certain alloys indicated that the compositions calculated in this manner were usually correct within 1.4 pct, as shown in Table I. All alloy specimens were wrapped in molybdenum foil before sealing them in silica tubes containing argon at a pressure of 1 atm at the annealing temperature. After quenching in cold water, the alloy specimens were bright and clean, with no evidence of any surface reaction. The alloys listed in Table I were examined metallographically, using an etchant consisting of 20 pet HNO3, 20 pet HF, and 60 pet Glycerine. powder for X-ray diffraction examination was prepared by crushing a portion of each annealed alloy

Jan 1, 1962

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel&apos;s paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel&apos;s attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,&apos;, y uranium, and perhaps zirconim.&apos; The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors&apos; reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato&apos;s value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,&apos;&apos; and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener&apos;s predictions.28 We have no quarrel with Hagel&apos;s placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By M. I. Sherman, J. D. H. Strickland

USE of a hydrometallurgical approach to the oxidation of sulfide ores and extraction of metals therefrom may have advantages over the more common smelting techniques when a low grade deposit is difficult to concentrate or the subsequent separation of metals, coexisting in the ore, is laborious by any known smelting operation. For economic reasons, the most promising oxidants are either atmospheric oxygen or electric power. The use of oxygen, or air under pressure, has recently been revised. Pyrrhotite has been converted to iron oxide and elementary sulfur&apos; and a variety of sulfides have been treated by Forward and co-workers.2-4 Generally sulfate is the end form of the sulfur but with galena in an acid medium, elementary sulfur can be formed." For economic reasons chlorine and ferric iron salts are about the only possible alternatives to the atmosphere as oxidizing agents for base metal sulfides. If aqueous solutions of chlorine or ferric iron are employed, the reduction products can be oxidized electrolytically in situ and used again, thus acting as catalysts for electric power as oxidant. The use of ferric salts for this purpose is established hydrometallurgical practicea but, although chlorine gas has been employed in the dry state at an elevated temperature, its use in aqueous solution at or near room temperature has not found favor. The reaction of chlorine water with the soluble sulfide ion has been studied by several workers,7-9 and both sulfate and elemental sulfur are found as end products, the latter being favored by the presence of a low concentration of oxidant relative to that of sulfide in solutions of about pH 9 to 10. Of direct bearing on the work in hand are an early American patent" and a recent Austrian patent." The former advocates stirring powdered ore with an aqueous solution of ferric chloride chlorine oxides and chlorine. In the latter it is claimed that both metal and sulfur can be obtained by electrolysis, in a diaphragm cell, of a metal ore slurry in brine. Details in these patents are scant and no data or explanation is given for the mechanism of the reaction which, in the Austrian work, is attributed to the (unlikely) action of nascent chlorine at the anode surface. No mention is made of possible differences in behaviour between various ores. Apparatus A complication encountered when working with chlorine water is that a serious loss of chlorine occurs by gas partitioning unless an enclosed system is used and any air space in the apparatus is kept very small and constant. Arrangements were made, therefore, to take out samples for analysis without letting air into the system to replace the liquid removed. For convenience in studying a heterogeneous reaction the apparatus was so designed that a reproducible controlled stirring rate could be maintained and the ratio of surface area of ore to volume of solution was approximately constant throughout any experiment. The apparatus used is shown in Fig. 1. The ground ore was placed in the horizontal cylindrical vessel, A, of about 1 liter capacity, heated by a constant temperature circulating bath pumping water through the concentric jacket, B. By adding chro-mate to this water, an ultraviolet radiation filter effectively surrounded the reaction vessel, greatly reducing any possible photochemical decomposition of chlorine solutions. Stirring was effected by glass paddles, C, attached by an axle to a magnet which was rotated by another powerful Alnico magnet, D, outside the glass end, this magnet being itself rotated by an electric motor electronically controlled to constant speed. Speed could be varied from about 150 to 900 rpm and was measured and held to within 1 pct of a given value. The end of the reaction vessel remote from the stirring magnet was closed by another one-ended glass cylinder, E, connected by thin polyethylene bellows, F, clamped by screw clamps and watertight rubber gaskets to the main vessel. Through E, a glass electrode and calomel electrode projected into the solution and a hypodermic syringe pierced a small bung and allowed acid or alkaline to be added to maintain a constant pH. By pushing the fully extended bellows until the two cylinders touched, from 50 to 100 ml of solution could be forced out through a sintered disk into the three-way tap system, G, either to waste (for flushing purposes) or up into a 10 ml burette where the solution could subsequently be measured out for analysis. The ore samples were introduced at H, the tube being stoppered by a thermometer of —1 to +52ºC range, graduated to 0.1°C intervals. To prevent ore from being ground in the end bearings of the stirrer these bearings were pro-

Jan 1, 1958

By C. A. Stickels

The preferred crystallographic orientations developed during recrystallization of polycrystalline electrolytic iron sheet, cold-rolled 90 pct, were ivestigated. Recrystallization at 500° or 565° C for relatively short limes produces a texture which is similar to the rolling texture. A duplex partial fiber texture, significantly different from the rolling texture, is found when the annealing time is increased. Recrystallization at 700°C also produces a sequence of textures with increasing annealing time. In order of their appearance, these textures are: 1) the duplex partial fiber texture found at lower temperatures, 2) a four-component texture "near {322}(296)", 3) a {112)(110) +(111)(110) texture, and 4) a two-component "near {554)(225)" texture. Secondary recrystallization, or discontinuous grain growth, accompanies the development of the latter texture. However, the "near {554} (225)" texture was nol observed when secondary recrystallization occurred under other conditions. All of the ideal orientations found in recrystallization textures can be accounted for by the growth of minor components of the deformation texture. IN recent years there has been increased interest in improving the drawability of metals by controlling the preferred crystallographic orientation of the sheet.1-l3 Since more low-carbon steel is drawn than any other material, considerable attention has been focused on the properties of sheet steel. Efforts to improve drawability through texture control have been hampered by the lack of any published systematic study of the recrystallization textures developed in iron annealed below Acl. The purpose of the present work was to supply some of this missing information, specifically, the recrystallization textures obtained by isothermal anneals of polycrystalline iron, cold-rolled 90 pct. LITERATURE REVIEW—DEFORMATION TEXTURES Barrett14 reviewed and summarized the investigations of rolling textures in iron and low-carbon steel prior to 1952. The texture of heavily deformed iron (rolled 90 pct or more) is described as consisting of two partial fiber textures. The dominant fiber texture (designated here as fiber texture A) has a (110) fiber axis in the rolling direction and includes the orientations (001)[110], {112}( 110), and {111}(110). The secondary texture (designated here as fiber texture B) is described as having a (111) fiber axis in the sheet normal direction, and includes the orientations {111)( 110) and (111)(112). Since the publication of Barrett&apos;s book, there have been two detailed studies of the deformation texture in polycrystalline iron. In both instances, the more sensitive diffractometer methods of pole-figure determination were used. Bennewitz15 studied the cold-rolling textures developed in polycrystalline low-carbon steel and a 3 pct Si steel. He determined (110), (2OO), and (222) pole figures for specimens reduced 30, 50, 60, and 90 pct and analyzed his results in terms of partial fiber textures. He distinguished three stages in the development of the final deformation texture. 1) Grains rotate to form two incomplete fiber textures, with (110) fiber axes inclined 30 deg to the sheet normal toward the rolling direction (fiber texture B). After 50 pct reduction, the highest density of poles is near an ideal orientation {554}(225), the two components of which are members of this duplex fiber texture. 2) With increasing amounts of reduction, grains rotate about the former fiber axes toward ideal orientations of the type {112)( 110) (common to fiber textures A and B). 3) Finally, grains rotate about their ( 110) axis in the rolling direction, clockwise and counterclockwise from the orientations {112}(110). This produces the range of orientations from (111)(110) to (001)(110) commonly found in the rolling texture of heavily deformed iron (fiber texture A). No significant difference was found between the deformation textures of low-carbon and silicon steels. A few years earlier, Haessner and weik16 had determined (110) pole figures for carbonyl iron rolled to 30, 60, 80, and 90 pct reduction in thickness. heir data agree quite well with the more complete data of Bennewitz, but a somewhat different description of the evolution of the deformation texture was given. The appearance of (110) poles in the transverse direction is ascribed to a (100)[011] component rather than "near {554}( 225) " components, and the (110) fiber axes of fiber texture B are described as located 35 deg rather than 30 deg from the sheet normal. Both of these studies agree that the secondary texture present in heavily rolled iron, the duplex fiber texture B, has (110) fiber axes and not a single ( 111) fiber axis normal to the sheet, as

Jan 1, 1965

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By Ingersoll Olmsted

Mr. D. H. BRowne&apos;s paper upon " The Distribution of Phosphorus in the Ludington Mine" (Trans., xvii., 616) has interested me very much, and perhaps I cannot give a better proof of that, interest than an account of my work and observations in the same direction while chemist of the Hudson River Ore and Iron Company. The ores of this company lie in a chain of low hills running northwest and southeast, about three miles back from the eastern bank of the Hudson river, below Hudson, N. Y. They occur in thick veins, with the characteristic Hudson river slate formation as hangingrock and foot-wall, and dip about 45&apos; east, outcropping in many places near the top of the western slopes.

Jan 1, 1890

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969