Search Documents

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By J. W. Gwinn

THE underground haulage system in the lead-silver mine of the-Bunker Hill & Sullivan Co., situated at Kellogg, Idaho, is the most extensive in the Coeur d'Alène district, comprising about 35,000 ft. of tunnels, drifts, and cross-cuts where locomotive haulage is in use. The main working adit, known as the Kellogg tunnel, or No. 9 level, is approximately 10,000 ft. in length from the portal to the main working shaft and extends beyond that about 4,500 ft. in each of two directions. On this level all the ore from the Bunker Hill & Sullivan, the Sierra Nevada Consolidated, and the Caledonia Mining Co. an average of 44,600 tons per month-is hauled to the mills, located a short distance from the portal. Electric haulage by the trolley-type locomotive is used on this level throughout. Below this level, at intervals of 200 ft. vertically, are five other working levels (Nos. 10, 11, 12, 13, and 14); and the total haulage distance on these, where electric locomotives are used, is approximately 16,000 ft. No. 13 level has but recently been opened up and is not working-to capacity; while the main cross-cut on No. 14 has just been started, and has no need of power haulage. Of the four levels equipped with electric haulage, Nos. 11, 12, and 13 have storage-battery locomotives, and No. 10 still retains the trolley type by reason of the small and decreasing tonnage produced.

Jan 2, 1915

By Harvey P. Knudsen, Young C. Kim

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling, and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 8, 1979

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

Abstract-A borehole sonde wing a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed.

Jan 6, 1978

By John Fulton

The Connellsville coal-field is a separate strip of the upper coal measures, flanking the Chestnut Ridge along its western side. It extends from a point a few miles south of Uniontown, in Fayette County, following a northeasterly course parallel to the trend of Chestnut Ridge, through Fayette and Westmoreland counties, with its terminal prongs resting 011 the southern portion of Indiana County, north of the town of Blairsville. This belt of coking coal will average about three miles in width and over sixty miles in length, affording nearly, if not quite, two hundred square miles of this large coal-bed.

Jan 1, 1885

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

By Edwin Chance

DURING the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that 'can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by, bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these

Jan 4, 1916

By Leon Dominian

The lack of Aryan roots for the names of metals commonly known among the Aryan settlers of Asia Minor, as well as the later colonizers of Europe, indicates that these races were generally ignorant of the use of metals until they came into contact with Semitic peoples. Practically all mining-terms in current use among the earliest Greeks resemble very strongly their distinctly Semitic equivalents, which can be traced all the way in a broad belt beginning in Lower Mesopotamia, and extending westwardly to the Syrian shores of the Mediterranean. The Greek word 'metallon," for instance, used indiscriminately to designate mine or ore, probably came from the earlier Semitic equivalent, " matal." Again, the Greek words " chry-sos " (gold) and " chalkos " (copper) seem to be descended from the Semitic forms " chrouts " and " chalak." It is a natural inference that primitive mining-methods were evolved by the dwellers in the mineralized areas of Asia Minor, from whom later Greek, Roman, and even North European miners obtained their first not.ions of the reduction of metallic ores, by

Jan 1, 1912

By C. W. George, Bruce Chalmers

The authors enumerate the factors which appear, from their observations and practical experience of failure of aircraft components in Great Britain, to be responsible for causing a metal or alloy to fail by stress corrosion. The essential conditions for promoting failure by stress corrosion are: (I) tensile stress at the surface of the component, (either residual or applied), and (2) an attacking medium that may be a solution or a liquid metal. Particular attacking agents are effective only on certain metals. In all instances of stress-corrosion failure experienced, cracking of an intercrystalline form has occurred and examples of such failure in aluminum alloy, steel and copper alloys are described and illustrated. The relation between microstructure and stress corrosion is mentioned and methods of investigating the susceptibility to stress-corrosion failure of metallic materials are described. The precautions to be taken in selecting materials for particular aircraft components and the importance of adequate protection against chemical attack are considered. The authors have given a factual survey of stress corrosion and have made no attempt to advance any scientific explanation of the phenomenon.

Jan 1, 1945

By E. T. Dumble

For many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gon-zales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in a rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure—possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitie division of the Eocene, with lignite, shells of iron, etc.

Jan 1, 1913

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By John M. Hartman

An examination as to irregularity of wear around the nose of the Witherbee tuyeres showed a section through the nose near the top as per Fig. 1, and a section only a half-inch beyond as per Fig. 2. The molten iron flowing over the nose of the tuyere had melted off the metal until the water in the tuyere prevented further melting. These tuyeres have a division in the annular water-space (see Fig. 2) to turn the current of water at the top, and the watersupply pipe is carried to within 1 inch of the nose. The constant supply of cold water in the nose of the tuyere kept it well cooled and preserved. But half an inch on the other side of the division the metal had melted off, as is shown by Fig. 1. There was no means of effecting a circulation at this point so long as the water was discharged from the butt of the tuyere. A pipe having been placed on the discharge-side of the division, the same as on the supply-side, in order to secure a circulation of the water at the nose on the discharge-side, it was found that the metal did not burn off. The nose being found to give out at the bottom, a division was placed in the annular water-space at the bottom, terminating 1 inch from the nose. This made a sharp current of circulation in the nose at the bottom, and prevented the burning of the metal there. A positive circulation at the nose, top and bottom, is a necessity with the present fast driving of furnaces, and prolongs the life of the tuyeres. The proper metallic composition of tuyeres is a question constantly agitated. A trial of ordinary yellow-metal* tuyeres was made 12 years ago. They did their work just as well

Jan 1, 1899

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By H. W. Clark

Electricity must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The moat dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All 'bare wires offer the same danger that troIley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain . shocks from the frames of locomotives and cars if track sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current. Fires Caused by Electricity The danger from fires caused by electricity arises principally from defective installation and careless upkeep or from injuries to equipment resulting from falls of roof or similar causes. Fires may be started by unrelieved short cifiuits, or grounds, by the blowing of open fuses, and by the overheating of resistances. Incandescent lamps can produce heat enough to ignite combustible materials if the dissipation of the heat from

Jan 1, 1915

By P. W. Bridgman

It is a commonplace that experimental physics in the last few decades has discovered manifold complexities in the atomic and subatomic levels, where it was thought for hundreds of years that no structure existed, as is witnessed by the derivation of the word "atom" itself. The field of exploration opened by the discovery of the electrical structure of the atom was so fundamental, rich and stimulating, that it has been almost exclusively cultivated by physicists since they obtained their first intimations as to the nature of the basic facts. Only within the last few years has it begun to dawn on us that we have overshot an enormous domain in which are situated many phenomena of fundamental importance for all the practical uses to which we put matter in our daily lives; the domain, that is, of most of the phenomena of interest to the biologist and the metallurgist. Furthermore, we are beginning to find that this intermediate domain is not entirely simple, but that it contains unsuspected complexities, some of them derived from the complexities of structure on the atomic and subatomic levels, and some of them emergent as matter collects itself into large aggregates, which often offer the key to the explanation of hitherto baffling large-scale properties of matter. Today I want to describe and consider some of these newly discovered complexities in the behavior of matter in bulk. The application to metallurgical problems is not always direct, but I hope to be able to suggest that such general notions as to structure as those here discussed must have important reactions on our attitude toward the problems of metallurgy. Three different sorts of phenomena of this kind to which I shall direct your attention are (1) the so-called structure sensitive phenomena, (2) complexities of such a nature that they are masked by the presence of extraordinarily small amounts of impurities, and (3) complexities depending on internal molecular rearrangements which can be understood only from the point of view of the quantum theory.

Jan 1, 1931

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By Valentine Garfias

THE various phases of the Mexican oil industry have received so much publicity that there is little to add to the discussion of present and future production, extent and importance of prospective fields, and status of petroleum legislation, to mention but a few of the angles of the Mexican oil problem. However, out of this wealth of information, which is generally of contradictory nature, the average petroleum man is at a loss to know something definite regarding the various questions involved so, keeping the foregoing in mind, it has been the writer's aim to record in a concise form the most reliable and up-to-date information regarding the salient features of the Mexican oil situation. PRESENT STATUS OF MEXICAN OIL INDUSTRY Production During 1921 The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of -these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 3 1/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields from about 755 per cent. of the Mexican petroleum industry.

Jan 4, 1922

By R. L. Andelin, J. D. Knight, M. Kahn

Self-diffusion in single-crystal tungsten and diffusion of rhenium tracer in single-crystal tungsten have been measured over the temperature range 2660° to 3230°C by direct sectioning and radio-chemical analysis of W185 and Re183 and Re184 tracers. The initial radioactive layer was produced on the diffusion specimens by bombardment with 9.0-mev deuterons. Diffusion heating of the samples in high vacuum was accomplished by induction heating. Temperatures were measured by optical pyrometry, and the system was calibrated ALTHOUGH a considerable body of experimental information has been accumulated on self-diffusion in solids, the major part of the detailed work has by reference to the melting points of tantalum (2996°C), molybdenum (2620°C), niobium (2468°C), and rhodium (1966°C). The diffusion coefficients for the two systems, obtained by least-squares analyses of the data, are well-represented by the equations thus far dealt with relatively low-melting systems. Diffusion studies on the high-melting elements niobium,1 tantalum,2,3 and tungsten4'5 have been limited to polycrystalline material, for which data interpretation and theoretical analysis are sometimes difficult. Only recently, a study has been made with single-crystal molybdenum.6 The present work deals with the measurement of self-diffusion in single-crystal tungsten at temperatures approaching the melting point (3410°c).7 Since the method chosen for producing the radioactive tracer layer-bombardment with deuterons—produced detectable isotopes of rhenium as well as of tungsten, the diffusion of rhenium was measured also.

Jan 1, 1965

By J. E. Johnson

The subject of blast-furnace slag is one which has had much consideration, particularly from the scientific standpoint, and several years ago technical literature contained many learned discussions on the oxygen-ratio of the acids and the bases, all on the assumption that acids and bases must be present in a ratio depending on molecular weight and chemical valency. Much work has also been don.e, sometimes in conjunction with the former, on the total heat and the temperature of initial fusion or softening of various slags. A wider knowledge of the blast-furnace now enables us to say that for practical purposes this work has been of almost no value. It is now generally admitted that on,the physical side the important point of a given slag is neither its total heat of fusion nor its softening-point, but its free-running temperature, since this is the critical temperature of the furnace. This temperature bears no definite relation to the softening-temperature, as determined by Seger cones, for instance, because some slags melt relatively like ice, with a very short viscous-range, while others melt relatively like tar, with a very long viscous-range. In one the difference between the softening- and the free-running temperature may be very small, as little as 100° F., while in another this difference may easily be 200' or 300°. The importance of this difference is so great in practice as to destroy completely the value of exhaustive investigations, even such as those of 0. Boudouard, published a few years ago.'

Jan 1, 1913

By W. W. Weigel

In "Mine Drainage, Southeast Missouri Lead District," Trans. AIME, (1943) 153, 74-81, the general water conditions in the lead mines of Southeast Missouri were described. Some comments developed from the experience of time and some further

Jan 1, 1949