Search Documents

By John Wulff, R. Buehl, H. Hollomon

Although the main features of the transformations occurring in 18-8 have been published already, certain conclusions merit questioning and discussion. The questions may be summarized as follows : 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenitc are both presumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundarices by chromium-carbide precipitation at these boundaries?

Jan 1, 1940

By R. Buehl, John Wulff, H. Hollomon

Although the main features of the transformations occurring in 18-8 have been published already, certain conclusions merit questioning and discussion. The questions may be summarized as follows : 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenitc are both presumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundarices by chromium-carbide precipitation at these boundaries?

Jan 1, 1940

By Blair R. Benner, Ronald J. Roman

The rate of acid leaching of malachite from a sandstone ore was shown to be controlled by the diffusion of H+ ions through the host rock. The kinetics of the reaction can be expressed by a shrinking core model. Equations for calculating effective diffusivities from an "infinite" slab and a cylindrical core were derived. The effective diffusivity, of H+ ions in a sandstone ore was measured.

Jan 1, 1975

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By AIME AIME

PRIZES totaling $450 were awarded at the Annual Meeting luncheon on Monday, Feb. 9, to the winners of the third national student prize paper contest. The undergraduate prizewinners, each of whom received a check for $100, were as follows: Mayo W. Lanning, Lafayette College, for his paper entitled ?Some Aspects of the Mining Methods Employed at the Scrub Oak Mines of the Alan Wood Steel Company,? (entered by the Lehigh Valley Section). Charles F. Parent, Montana School of Mines, for his paper entitled ?Relationships of Manganese Minerals in the Butte District,? (entered by the Montana Section). Harry Czyzewski, University of Illinois, for his paper entitled ?A Metallurgical Study of Cast Irons Used for Glass Molds,? (entered by the Chicago Section).

Jan 1, 1942

By H. R. Hoffman

SINCE slag is a necessary product of the reactive oxygen additions necessary to the present-clay quality steelmaking, the study of the control of its volume is being attempted. With other varying factors that may affect the volume of slag kept as nearly constant as possible, the object of this investigation is to determine what effect the one factor of varying the amounts of iron-ore additions and the time of the additions may have upon the volume of slag in producing an acid electric steel heat.

Jan 1, 1947

By C. Gutiérrez

Flotation and adsorption studies of ilmenite with technical oleic acid, pure oleic acid, and mixtures of each of them with n-hexadecane have been conducted. From them it is concluded that the depression of ilmenite caused by a too long conditioning time is due to adsorption of the collector onto the fines produced by attrition in the conditioning cell, and that fuel oil is necessary for economic flotation of non-deslimed ilmenite ore. This beneficial effect of fuel oil is attributed to van der Waals forces, of the hydro-carbon chains.

Jan 1, 1978

By C. Willard Hayes

The determination of the question whether the Mayari and Moa mining-claims of the Spanish-American Iron Co. have been rightly denounced under the third section of the law of bases rests on the findings in the following questions of fact: 1. Is the mineral an iron-ore ? 2. Is the iron-ore a bog iron-ore ? 3. Is the iron-ore ocher ? 4. If ocher is present, can it be mined separately and independently of the iron-ore ? 1. Is the Mineral an Iron-Orb? Since the material is shown by a large number of analyses to contain from 41 to 50 per cent. of metallic iron and less than

Jan 1, 1912

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

(The following -list, contains the navies of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A com-plete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ADDICKS, LAWRENCE, Naval Consulting Board. ALINE, P. A., Camp Lewis. BARCUS, WALTER .J. E., Captain, Ordnance Department. BAUSH, JOHN R., Private, 1st Army Headquarters Regiment, Co. M. BENNETT, A. F., Lieutenant. BILLINGSLEY, PAUL, Engineer Officer, Aviation Section, Signal Officers' Reserve Corps. BOOTH, L. E., Ordnance Department. BROWN, JAMES F., 2d, 1st Lieutenant, Ordnance Reserve Corps, A. E. F.

Jan 4, 1918

By H. W. Young

Development of high-tension outdoor substations during the past few years has been due primarily to economic reasons. The demand for power in small communities could not be met with the conventional and Fig. 1.—33,000-VOLT step-up outdoor air-break switch and substation installation outside of a powerhouse generating at 2300 volts stepping up to 33,000. Twenty-one coal mines are supplied from lines leading from this installation. comparatively expensive indoor types unless the rate for service was materially increased. To prove that the problems lncident to development have been solved successfully, it is only necessary to point to the wide adoption of outdoor substations by utility companies. Passing at once to the question as to whether outdoor substations are applicable to

Jan 1, 1920

By H. Scott

SINCE Böhler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar3_2_1 obtained by increasing the maximum temperature to which the material was heated, much has been published' connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The, significant facts established by recent investigators' are: that when the' transformation occurs at the higher temperature Ar', troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin.3

Jan 2, 1919

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir's previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l'unctions, can be used to calculate future behavior for any production schedule.

By R. S. Schechter, T. R. Guilinger, P. Bobeck, J. G. Price, L. W. Lake

This paper presents the results of an experimental study on the rate of uranium and molybdenum extraction from a flow reactor. Specific variables tested are fluid throughput and flow rate, lixiviant cation, and injected pH and carbonate concentration. The ore tested was from the Felder mine in southern Texas. It contained substantial quantities of marcasite and molybdenum disulfide that competed with the uranium ore for oxidant. Flow studies showed the oxidation of molybdenum disulfide under field conditions is mass transfer controlled, whereas the uranium oxidation is limited by surface reaction rate. The rate of uranium oxidation decreased with decreasing pH. The total carbonate levels, on the other hand, were unimportant. Ammonium carbonate appears to greatly decrease, if not completely halt, the reaction of marcasite with the oxygen. This effect was not found using either sodium or potassium carbonate.

Jan 1, 1986

By Alden B. Greninger

The study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics. Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure. Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,² and very little attention has been paid to the visible imperfections of crystals. A. Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory.3 On the other hand, Smckal,4 and Orowan,5 among others, maintain that there is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure. Lately the subject has been intensively investigated by Buerger,6 one of whose recent papers led to a symposium on mosaic structures.'

Jan 1, 1935

By Alden B. Greninger

The study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics. Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure. Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,² and very little attention has been paid to the visible imperfections of crystals. A. Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory.3 On the other hand, Smckal,4 and Orowan,5 among others, maintain that there is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure. Lately the subject has been intensively investigated by Buerger,6 one of whose recent papers led to a symposium on mosaic structures.'

Jan 1, 1935

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) *AMBLER, HARRY A., 1st Lieutenant, 0. R. C., 30th Infantry, A. E. F. BAKER, R. F., Private, Intelligence Section, Headquarters 90th Division. *BARTON, L. A., Captain, 604th Engineers. *BATTEN, H. L., Lieutenant, Canadian Engineers, C. E. F. *BENSEL, J. A., Major, U. S. Reserves. BIRKETT, HOWARD, Lieutenant, Aviation, U. S. Signal Corps. BLOOMFIELD, E. C., Lieutenant, 1st Canadian Tunnelling Co. BOOTH, L. E., Watertown Arsenal, Det. E. 0. C., N. A., Watertown, Mass. *BOWMAN, REGINALD G., 1st Lieutenant, Engineers, U. S. R., Int. Ord. Dept. No. 4, A. E. F. *BRADLEY, CLARENCE I., Convois Automobile Section 585,. S. S. U., P. A. R., B. C. M.

Jan 7, 1918

EUGENE MCAULIFFE, St. Louis, Mo. (written discussion*).-When we undertook the development of the Kathleen mine, near DuQuoin, certain features greatly influenced the construction and underground development. The country is very flat, so that the usual gravity yard movement of empty and loaded coal cars would entail a very heavy fill at the empty-car end of the tracks, with some form of car-pulling arrange-ment to move the loads where it was practically impossible to provide. a gravity movement. So the yard was made level, except for 1000 ft. (304 m.) under the two tipples, where the cars are moved by gravity and controlled under the main-shaft tipple by four Fairmont car retarders. Both tipples are spread sufficiently to admit of introducing a narrow-gage track and locomotive. One 18-ton locomotive is at present employed in moving empties clown to a point above the main-shaft tipple and the loads off the track scales clown into the storage yard; ultimately a 25-ton loco-motive will be employed on the loaded side of the tipple. This form of car movement and control will admit of handling empty and loaded cars

Jan 11, 1919