Search Documents

By B. M. Larsen, T. E. Brower

For some years we have been carrying on a rather comprehensive investigation of the occurrence of oxygen in liquid open-hearth steel. This investigation was interrupted by the war emergency and is therefore incomplete, with many questions still answered only partially, if at all; yet it seemed worth while to present a report of progress on this difficult field of research, if for no other reason than to promote discussion and further investigation of this important problem. The significance of such studies depends in large measure upon the accuracy of measurements of oxygen content in liquid steel while it is still in the furnace or as it flows into the ladle, or thence into the mold and there is, as we shall show, good reason for believing that the main source of uncertainty is in the sampling, not in the analytical method as such. The difficulty arises from the fact that any method of sampling is of itself apt to alter the amount of oxygen in solution in the liquid steel, because this oxygen is in a readily reactive condition. On the one hand, being usually present at a concentration appreciably in excess of that corresponding to equilibrium with the carbon then present, it may decrease rapidly in percentage by reaction with carbon and evolution of CO, especially if the liquid metal is in any way shaken or brought in contact with a cooler solid surface. On the other hand, it may increase rapidly by ab- sorption of oxygen from a slag, a furnace atmosphere, or from air. These circumstances, which are inherent in the problem, as well as our conclusion that, despite the considerable amount of careful work already done, there is still no method of sampling liquid steel acceptable as an unquestioned standard, ed us to undertake systematic comparisons of oxygen content of large numbers of samples taken: (I) by a single method at different positions and levels in the bath; (2) at the same place by different sampling methods; and (3) from bath, tapping stream and pouring stream. The different sampling methods yield somewhat different values and there is as yet no way to tell with certainty which is the most accurate. But the general reproducibility and consistency of the results give us some confidence in certain inferences we draw from them: namely, that the "spoon" method of sampling, properly carried out, gives somewhat more consistent results than the "bomb" method, as it has usually been practiced; that, in the bomb method, an aluminum cap is preferable to a steel cap; that the oxygen content of liquid steel in a finished heat is substantially the same all over the bath at the same level, and tends to decrease at lower levels further from the slag interface; also that it tends to decrease, and to decrease erratically, from furnace bath to tapping stream entering the ladle. Accordingly it seemed desirable to report these observations in detail as a first step, so that the reader may judge their significance as a contribution towards solution of the main problem, which is to find a means of pre-2

Jan 1, 1945

By E. P. Polushkin, Henry L. Shuldener

THIS paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. PIPES EXAMINED The pipes were made by different manufacturers and their sizes range from ¾ in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often 100 to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is 100° to 160°F. WATER SUPPLIES The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table I are characterized by relatively low hardness, low alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1944

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined' as a zone of

Jan 1, 1948

By Arthur F. Taggart, Nathaniel Arbiter

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943

By A. H. Geisler, J. H. Keeler

Preferred orientations in unalloyed zirconium were determined by the Geiger-counter spectrometer X-ray diffraction technique. With increasing P-annealing temperature the following textures were obtained: l—a retained a-annealing texture, 2—additional orientations predictable from the a-p (Burgers) relationship, and 3—a texture derived from a cube texture in the p phase. Earlier work on cold-worked and a-annealed zirconium was reappraised to show a quantitative dependence of rotations on temperature and to identify spurious areas of some of the pole figures. IN a previous paper,' the preferred orientations of high purity zirconium sheet were described for cold-rolled and annealed samples. Annealing temperatures up to 900°C, which is slightly above the allotropic transformation temperature, were explored. Of interest was the observation that the orientation of the hexagonal-close-packed material after annealing in the temperature range of the stable body-centered-cubic phase was similar to that of the material which had been annealed in the a temperature region, although a change in texture would be expected because of the many new orientations based on an orientation relationship between the two forms of zirconium. The reversion to an original orientation after an allotropic transformation cycle is not unusual. It has been found for titanium,"* for thallium," and for cobaltB among the hexagonal metals. Burgers found in his original work7 that, when zirconium was cooled through the allotropic transformation and then reheated, the body-centered-cubic phase reverted to the original orientation. Additional experimental work has been carried out to further explore the textures of zirconium after annealing in the temperature range above the allotropic transformation. In addition, a reappraisal was made of the earlier results for zirconium' in light of recent work on titanium4 which has shown that the texture type depends quantitatively on the temperature of annealing and that spurious areas may be encountered in the pole figures of hexagonal metals determined by the X-ray spectrogoniometer technique of analysis. Experimental Procedure Crystal-bar zirconium prepared by the iodide process was the material used in this investigation. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in., after which it was cold rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed for % hr at 1000" to 1100" to 1200°C or 1 hr at 1400°C in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by

Jan 1, 1956

By Nathaniel Arbiter, Arthur F. Taggart

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943

By Arthur Notmon

WORLD production of the three major nonferrous metals, copper, lead, and zinc, in 1939 will aggregate about 6,050;000 tons, compared with the all-time peak of 6,237,944 tons in 1937, and the previous peak of 5,679,442 tons in 1929. The United States will furnish 30.9 per cent of the total compared with 30.4 per cent in 1937 and 41.3 per cent in 1929. Table 1 gives the details of the three metals.

Jan 1, 1940

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. 'Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By D. S. Kingery, D. W. Mitchell

The authors attended the 11th International Conference of Directors of Safety in Mines Research held in France, July 1963. In addition to Conference discussions pertaining to control of coal dust they had the added assignment to study present European practices for neutralizing the coal-dust explosion hazard. Information was obtained through discussions with the Research Directors, by visits to testing stations and observations of operating mines in various countries. This paper tells what the current practice in this field is in Europe, and how effectively coal dust explosions are controlled. The method is rock dust barriers. CONTROL OF COAL DUST DISSEMINATION Experience in Europe indicates that the control of dust production and dissemination by water or foam systems is not successful except during undercutting. Cybulski, Dawes, and DeBraaf - respectively Director, Mines Research Establishment "Barbara", Katowice, Poland; Principal Scientific Officer, Safety in Mines Research Establishment, Sheffield, England; and Chief, Central Mines Research Establishment, Hoensbroek, Treebeek, The Netherlands - believe that wetted dust becomes readily dispersible and abatement measures should be considered only as a temporary means for reducing the health hazard. In an effort to reduce the health hazard, calcium chloride is used on the floor of main haulageways in Dutch mines and water infusion is practiced in Germany in mines where the coal is relatively porous. With respect to wet coal dust, the Belgians, British, Dutch, French, and Russians reportedly have accepted the results of research from the Polish and American experimental mines on the effectiveness of water as an inert in arresting explosion propagation. The Polish use the two test methods proposed by the U.S. Bureau of Mines1 for evaluation of the adequacy of wetness of mine dust; they require that water be added to the wet dust to maintain a minimum of 50% moisture by weight if dependence is placed on water alone. GENERALIZED ROCK DUSTING The general attitude with regard to protection against coal dust explosions throughout Europe is that generalized rock dusting is a vital primary step to inhibit initial ignitions but definite emphasis is also placed upon the efficiency of rock dust barriers. Those exceptions to generalized rock dusting are Germany and Austria where some rock dusting is done but principal reliance is placed upon rock dust barriers. The rock dust used in Belgium, Holland, Russia, and Poland is coarser than that used in the U. S.; 50% of the dust is through a No. 200 sieve (75 microns). Recent research by the Polish indicates that the portion finer than 20 microns is ineffective in arresting explosion propagation, and that the rock

Jan 1, 1964

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.' High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.‡ Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; 2.3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:' I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By B. L. Sackett

The converting of lead matte is not a general practice at lead smelters, therefore a description of the methods used and developments made during the past 20 years in converting both lead and copper matte at the Tooele plant of the International Smelting Co. in Utah may be of interest. The Tooele converting plant consists of five electrically operated stands in which are used 96 by 150-in. horizontal, barrel-type converters each of about 10 tons capacity. The main converter building is served by a 60-ton electric traveling crane and the casting shed by a 30-ton crane. Copper matte is tapped from near-by reverberatory furnaces into launders that deliver into 8-ton ladles on the converter floor. Lead matte is brought from the blast furnaces, about li mile away, in 5-ton ladles mounted on trucks, hauled by electric locomotives. As the Tooele copper plant has never been a producer of much copper, and has been Irregular in its operation, the original converting plant with its small converters has been adcquate, although decidedly out of step with large, modern plants. Tonnage figures in this paper are for comparison with each other only, as they are not at all in line with prevailing tonnages at larger plants today. The reasons for the changes made in converting practice at Tooele, as well as the improvements in the results obtained as these changes were perfected, are given in the following pages. Lead-matte Converting, 1914 to 1927 In 1914, Oscar M. Kuchs wrote a paper for the Transactions,' describing in detail the lead-matte converting methods at Tooele up to that time. The method perfected only a few months before Mr. Kuchs' paper was written consisted, briefly, of blowing the lead matte alone, without the addition of siliceous fluxing ores, to a point where the lead and zinc were largely eliminated by volatilization. During this period

Jan 1, 1934

By J. Th. Erb

The total crude oil production of these islands, which in 1928 amounted to nearly 5,000,000 metric tons—about 36,500,000 bb1.—has again increased in 1929. The figures for 1929 are as follows: Metric ToNs† North Sumatra........................................ 369,930 South Sumatra........................................ 1,236,510 Java and Ceram....................................... 678,787 Dutch Borneo (including Tarakan)....................... 2,793,326 Sarawak.............................................. 759,700 Total............................................... 5,838.253 †1 metric tor1 = 7.36 bbl. on the average. This production, as far as the Dutch Islands are concerned, is owned partly by the Bataafsche Petroleum Maatschappij, the producing subsidiary of the Royal Dutch Petroleum Concern, and partly by the Kolon-isle Petroleum Maatschappij (Standard Oil Co. of N. J.), while that of the British Protectorate Sarawak belongs to the Anglo-Saxon Petroleum Co., Ltd., of London. The increase in 1929 is due partly to more intensive drilling; the rotary system, which enables drilling to be done more quickly and to greater depths than was possible with the percussion system, has come into more general use. Further, considerable extensions have been made to some of the existing fields and several new pools have been discovered, which contributed in no small degree to the increase in production. Of particular interest is the fact that the ('Niam" (Nederlandsche Indische Aardolie Maatschappij), in which the Dutch Government has a large share and which company in 1928 was producing from only two fields in South Sumatra, has discovered a pool in North Sumatra and, moreover, has struck oil on the island of Poeloe Boenjoe near Tarakan (Eastern Borneo). The deepest well still drilling is in one of the fields of the "Niam" and has reached a depth of 2269 meters (7445 feet). Notwithstanding the tropical c1imate and the dense jungle in which most of the fields are situated, the most modern scientific methods are applied in exploration, in drilling, producing and refining.

Jan 1, 1930

By W. M. Weigel

The first successful use of the wire saw in slate quarrying in the United States was late in 1926, at the quarry of the Colonial Slate Co. near Wind Gap, Pa. This installation was sponsored and supervised by the United States Bureau of Mines in collaboration with the National Slate Association.' The success of this trial resulted in other installations of wire saws, so that 27 were in operation at Pennsylvania slate quarries2 by October, 1928. Marble Quarrying with a Wire Saw Until recently, little or no attempt has been made to use the wire saw in the quarrying of other stone, but it is believed that its successful use in slate will be followed by attempts to take advantage of its possibilities in other quarrying operations. An example of such a trial is the recent installation of a wire saw at the marble quarry of the Saint Clair Marble Co. near Guion, in the Ozark region of northern Arkansas. This quarry is in a comparatively new district and the decision to open and develop it had to be made in the face of many unknown factors. For this reason, it was essential that the development costs be held at a minimum, and as a wire saw could be installed more cheaply than standard channeling equipment, it was decided to try it out. One factor Largely controlling the decision was that the location was peculiarly adapted to this method. The point of development selected was on the rather abrupt end of a ridge formed on the south by an almost perpendicular bluff along the White River and on the north by a rather steep slope with little or no overburden. By taking advantage of this topography it was possible to place the supporting standards for the sheaves at both the outer and driving end without the necessity of drilling or excavating openings to receive them, and to locate the motive power in line with these standards, which made it unnecessary to deflect the sheaves.

Jan 1, 1931

By R. G. Webber, F. C. Langenberg

During the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point. The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the bars was tested in this manner and in no instance could any difference in structure in the three specimens1 be detected. Bars 1 to 3 inclusive are pearlitic in structure. The white areas are ferrite (iron with certain impurities in solution) and the dark areas pearl-

Jan 1, 1915

By R. G. Treuting, R. M. Brick

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942