Search Documents

By Louis S. Cates

At the annual meeting of the American Institute of Mining and Metallurgical Engineers in February, 1923, the Chairman of the Committee on Ground Movement and Subsidence appointed a sub-committee to work out a form of questionnaire and to collect data on subsidence and ground movement resulting from underground metal and coal-mining operations, and on ground movement and safe slopes in connection with open-cut metal-mining operations. The author was requested to take charge of the collection of data and the preparation of a questionnaire in connection with the Committee's studies of open-cut metal-mining operations. This paper is a summary of the work carried on and information received therefrom up to February, 1924. The first approach to the problem of safe slopes is to gather all information that pertains to finished slopes; in other words, the steepest economic angle from the horizontal that will stand in order to uncover the ores to be mined and be safe while the extraction of the ore at the base of these slopes is in progress. Whether or not this angle is 35" or 45" depends on many factors. The number of benches maintained to take care of falling rock and their height and width are direct functions of this overall slope. The slope is here taken to mean the angle from the top edge of the pit through the edges of the respective lower benches to the bottom of the pit. If we accept this definition of the slope, it might save some confusion as there would be a difference if one took the line from the top edge of excavation to the toe of the bottom slope. This latter slope would not be constant, but would vary with the number of benches. The depth of the various ore faces will vary, of course, depending on the deposit; Table 1 shows this to range from 50 ft. to 1100 ft. The geology is an important factor, as are the climatic conditions under which one is operating. A saturated condition in some rock structure causes rock flows; in the Panama Canal excavation, slides have run on a ratio of as low as one on ten, which is a 10 per cent. grade, or a slope of less than 6' with the horizontal. Slopes as steep as 60' have been noted in the Utah Copper operations, so that a wide divergence will possibly be met. The work of securing data that will be of value to the operator or estimating engineer will be difficult and will mean little unless a detailed

Jan 1, 1927

By R. T. Carter

THE phase behavior of a number of binary systems consisting of paraffin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.1 However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the co-existing phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system.

Jan 1, 1940

By V. R. Garfias, R. V. Whetzel, J. W. Ristori

Since the entry of the United States into global war, virtually all data and information necessary for compiling figures on world petroleum consumption have become unavailable. This situation undoubtedly will continue until the world petroleum industry can return to a peacetime basis. During the past 10 years, the authors, by publishing annual estimates of .world consumption, have attempted to emphasize the importance of a yearly world-wide survey of petroleum supply and demand. It is beconling more and more evident that statistics for the United States alone can no longer give a comprehensive idea of the state of the petroleum industry, even within the United States itself. Therefore, when conditions in the industry again become normal, it is the hope of the authors that those bureaus equipped to do so will carry forward the study of petroleum supply and demand on a world-wide basis. Enough data and information are available, however, to attempt a rough estimate of world output of crude petroleum and petroleum substitutes for 1942, which to some extent may reflect the trend of world consumption. This estimate by countries, as compared with the output in 1941, is shown in Table I. The world production of crude petroleum and petroleum substitutes for 1942 is estimated at 2,208,000,000 bbl., or a decrease of 171,000,000 bbl. under 1941. Crude production is believed to have decreased by about 200,000,000 bbl., (about 9 per cent); while petroleum substitutes increased by 28,500,000 bbl., (nearly 20 per cent). The decline of crude output in the United States is estimated at 19,000,000 bb1.—less than 2 per cent; while that in foreign countries is estimated at 180,000,000 bbl., or more than 20 per cent. The marked decline abroad is due largely to losses in Venezuela and Colombia, where the lack of ocean transportation became the controlling factor, and in the East Indies and Burma, where military invasion brought about the destruction of the fields. The production of petroleum substitutes in 1942 apparently reached a new high figure of 7.5 per cent of the total world petroleum output. The important features of petroleum production outside of the United States are the changes that have taken place during the year in the supply of the Axis countries. In Japan the output for 1941 was estimated at 8,800,000 bbl., 5,500,000 of which were petroleum substitutes. It is believed that the output of synthetic oils during 1942 substantially increased, raising the total interior production of Japan to nearly 10,-ooo,ooo bbl. Also, during 1942 Japanese armed forces gained possession of oil fields having a normal peacetime output of about 78,000,000 bbl. per year. The production of these areas for 1942 is estimated at some 23,000,000 bbl., which indicates that Japan is now getting at least 33,000,000 bbl. a year, which exceeds by 8,000,000 bbl. Its

Jan 1, 1943

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

By J. W. Ristori, V. R. Garfias, R. V. Whetzel

Since the entry of the United States into global war, virtually all data and information necessary for compiling figures on world petroleum consumption have become unavailable. This situation undoubtedly will continue until the world petroleum industry can return to a peacetime basis. During the past 10 years, the authors, by publishing annual estimates of .world consumption, have attempted to emphasize the importance of a yearly world-wide survey of petroleum supply and demand. It is beconling more and more evident that statistics for the United States alone can no longer give a comprehensive idea of the state of the petroleum industry, even within the United States itself. Therefore, when conditions in the industry again become normal, it is the hope of the authors that those bureaus equipped to do so will carry forward the study of petroleum supply and demand on a world-wide basis. Enough data and information are available, however, to attempt a rough estimate of world output of crude petroleum and petroleum substitutes for 1942, which to some extent may reflect the trend of world consumption. This estimate by countries, as compared with the output in 1941, is shown in Table I. The world production of crude petroleum and petroleum substitutes for 1942 is estimated at 2,208,000,000 bbl., or a decrease of 171,000,000 bbl. under 1941. Crude production is believed to have decreased by about 200,000,000 bbl., (about 9 per cent); while petroleum substitutes increased by 28,500,000 bbl., (nearly 20 per cent). The decline of crude output in the United States is estimated at 19,000,000 bb1.—less than 2 per cent; while that in foreign countries is estimated at 180,000,000 bbl., or more than 20 per cent. The marked decline abroad is due largely to losses in Venezuela and Colombia, where the lack of ocean transportation became the controlling factor, and in the East Indies and Burma, where military invasion brought about the destruction of the fields. The production of petroleum substitutes in 1942 apparently reached a new high figure of 7.5 per cent of the total world petroleum output. The important features of petroleum production outside of the United States are the changes that have taken place during the year in the supply of the Axis countries. In Japan the output for 1941 was estimated at 8,800,000 bbl., 5,500,000 of which were petroleum substitutes. It is believed that the output of synthetic oils during 1942 substantially increased, raising the total interior production of Japan to nearly 10,-ooo,ooo bbl. Also, during 1942 Japanese armed forces gained possession of oil fields having a normal peacetime output of about 78,000,000 bbl. per year. The production of these areas for 1942 is estimated at some 23,000,000 bbl., which indicates that Japan is now getting at least 33,000,000 bbl. a year, which exceeds by 8,000,000 bbl. Its

Jan 1, 1943

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that 'is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:',' oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By C. H. Benedict

1. Shaking Tables 2. Fine Grinding 3. Hydraulic Classification 4. Mechanical Thickeners 5. Flotation ENTERING the profession of minerals beneficiation (it was plain garden variety "ore dressing" . in those days) I was fortunate that at that time the first major innovation in modern ore dressing practice was being introduced. I refer to the Wilfley table. You youngsters that came into the game only 30 years ago or even more recently, with flotation machines and reagents as your very ready tool in time of trouble, do not realize what the invention of the Wilfley table meant to us. We had but one physical property of ores to reckon with-specific gravity- and when there was but little difference in specific gravity between the mineral and the gangue, we were in trouble. The jig and the revolving table were our only mechanical equipment for recovering values and so that we might make even a reasonably satisfactory extraction, we had to classify and reclassify, and jig and rejig, and worry about the laws and advantages of free settling vs hindered settling and just tire the minerals out.

Jan 10, 1954

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y' (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y' morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y' precipitate in

Jan 1, 1967

By D. O. Ehrenburg

DURING the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumberger1 have given a more theoretical discussion of the resistivity methods. Hummel and Stefanesco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases.

Jan 1, 1931

By H. R. Page, A. E. Jr Lee

A. E. LEE, JR. (author)—In addition to the paper we should like to make a few remarks. First, the seriousness of bending of the clay retort cannot be overemphasized. Not only did bending limit the length of the vessel, but it permitted corrosive fluid slags to concentrate in the belly of the retort and thus increased the possibility of boring. Bending also practically prohibited the use of cleanout machines and increased the danger of excessive fume losses by allowing furnace gases to escape around the top of the retort mouth. It will be noted that the Blackwell pottery practice places considerable emphasis on careful drying of retorts. Perhaps it is another smelter superstition, but traditionally the aging of retorts beyond a reasonable drying period has been considered important to long life. We are unable to give a good explanation of why aging should improve retorts. During the past fall in an attempt to prove a theory that the combined water in the clay decreased during aging, about 50 samples of wet retort collars were placed in a dry room when it was closed. Loss of weight, combined water and free moisture were measured each week over the 100 day drying period. The affinity of the dried retort for moisture makes difficult the accurate measurement of free water; however, there was a clearly defined free moisture change from about 12.5 pct when freshly made to about 2 pet at the end of 18 days, then a gradual loss to about 0.25 pet at 70 days and an apparent equilibrium near this figure through the 100th day. There was no appreciable change in the combined water. The change in weight of the average sample was, however, rather unusual, there being consistently a loss of weight throughout the entire 100 days. From the 63rd day on this leveled off to about 0.03 pet per week. These were small samples and certainly should have dried

Jan 1, 1950

By Ganesh P. Mohanty, James J. Wert

THE brittleness of the intermetallics usually render their deformation studies at ordinary temperatures using conventional techniques inadequate. On the other hand, although X-ray line broadening measurements is not a complementary technique, it provides a means for gaining limited but useful information on the cold worked state of these materials. In the present instance, a study of the effects of cold work in the lead telluride intermetallic compound was carried out by analyzing the diffraction profiles of the deformed and the corresponding annealed samples. An ingot of PbTe was prepared by induction melting high-purity lead and tellurium in a quartz crucible under an atmosphere of argon. After homo-genization, the ingot was ground to -325 mesh at room temperature, and using a polished die the cold- worked powder was pressed into the form of flat faced briquets for diffraction measurements. A spectrometer with 0.125 deg per min scanning velocity, CuKa radiation, pulse height analyzer, and a proportional counter were employed in the X-ray measurements, and the powder peaks were collected from the sample in fully cold-worked state and after it had been annealed to relieve the effects of cold work completely. For reliable estimates of the peak extremities, small angular ranges where the tails merged into the background were point counted. Fourier inversions of the experimental peaks were carried out in an IBM 705 computer using the procedures introduced by stokes.' Both the cosine and sine components of the Fourier series were used to take into account any peak assymetry arising

Jan 1, 1963

By Charles Catlett

An examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz, which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone mere observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, arid the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, arid the

Jan 1, 1908

By David R. Poirier

THE activity of carbon in Fe-C-Cr liquid solutions has been measured by Richardson and Dennis,1 Fuwa and chipman,2 and Goto et aL3 Fuwa and Chipman2 have presented their data along with data of Richardson and Dennis1 and utilized an interaction parameter. However, the interaction parameter is only valid for dilute solutions of carbon, because, as indicated, the same interaction parameter does not apply to more concentrated solutions of carbon (i.e., the effect of chromium on the saturation of graphite in liquid iron). Ohtani4 has attempted to account for the effect of carbon concentration on the interaction parameter; however even his analysis does not apply to the saturation data. Also, the effect of temperature on interaction parameters must be taken into account. Therefore, in any process where the concentration of carbon and/or the temperature changes (such as solidification), the use of an interaction parameter is not adequate to know the activity of carbon. The purpose of this communication is to make use of the existing data on the effect of chromium on the activity of carbon in liquid iron solutions in such a way that the activity can be described as a function of both composition and temperature. The method is an extension of Rist and chipman's5 analysis for the binary Fe-C solutions. As in Rist and Chipman's analysis, the activity coefficient is assumed to obey the relation: log y1 = at(l -X1)2 + It [1]

Jan 1, 1969

HENRY FAY, Cambridge, Mass. (written discussion *).-Mr. Rawdon has made a distinct contribution to our knowledge of wrought iron, and .perhaps of steel. It will undoubtedly lead to more careful scrutiny of high-phosphorus steels, with perhaps important results. In view of his results, it would seem to be unprofitable to push further any propaganda on the use of higher-phosphorus low-carbon steels until further information is available. As is well known, and as Mr. Rawdon clearly shows, the process of solidification is a selective one, and there is abundant opportunity for those portions of the melt last to solidify to become rich in phosphorus, and the diffusion of this phosphorus-rich area is slow. Hot work does not help the situation appreciably and only serves to concentrate the low-melting material. It is undoubtedly true, as some writers have recently claimed, that the specifications for steels as they. now exist eliminate some perfectly good material. Higher phosphorus in steel may be perfectly safe provided all of the phosphide is completely and uniformly, diffused in the solid solution. If, on the contrary, it is not evenly diffused, and there is a reasonable chance for it not to be, it makes the steel unsafe. Until our knowledge: of the rate of diffusion of phosphorus in steel, and the effect of other elements upon the rate, is more complete, it seems to me unwise, in view of Mr. Rawdon's experiments, to listen to the recommendations for the use of higher-phosphorus steels.

Jan 1, 1918

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A' of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A') and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A'. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935