Search Documents

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By J. Greenspan

The anisotropy of fracture and slip, that is, the brittleness and ductility of the beryllium single crystal, is characteristic also of po1ycrystalline beryllium in which the grains are oriented in a preferred manner. Beryllium with grain orientations resulting from hot working either unidirectionally or bidirectionally is ductile or brittle in directions given by the anisotropy and orientation of the grains. Textures developed from various hot-working sequences are given, and tensile results are correlated with textures. Not only texture, but fine grain size is necessary for obtaining high tensile elongation. Ultimate tensile strength and elongation are both correlated with grain diameter. Of particular interest is the case in which unusually high tensile elongations of 30 to 40 pct are obtained when basal planes are oriented to carry THE beryllium crystal (of nominal purity) is probably unique among metals with respect to its unusually acute anisotropy of slip and fracture. While extensive slip can occur on the system (1010) [ll20] starting at about 19,000 psi, the (0001) plane is particularly vulnerable to fracture at 4500 psi or less. Fracture occurs also on the (11zo) plane at about 26,000 psi.1"3 Further, there seems to be no other slip System which contributes significantly to

Jan 1, 1960

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

By P. H. Brace

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly; iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale or which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time.

Jan 1, 1928

By P. H. Brace

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale or which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time.

Jan 1, 1928

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By M. E. Lombardi

Discussion of the paper of AI. E. LOMBARDI, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 2109 to 2114. C. D. KEEN, Shreveport, La.-Did Mr. Lombardi include in his figures the purchase price of the property? M. E. LOMBARDI, Berkeley, Cal.-No. C. D. KEEN.-Suppose I pay $1,000 per acre for it, and in four or five years it is worked out. M. E. LOMBARDI.-That is a question of depreciation and must be added to my figures. MARK L. REQUA, San Francisco, Cal.-You say it cost $35,000 to $40,000 a year to maintain 1,000-bbl. per day production? M. E. LOMBARDI.-Yes, 1,000 bbl: a day would cost $40,000 a year to maintain.

Jan 12, 1915

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By H. B. Bailey

SiNcE the gypsum deposits of Nova Scotia have been operated on a large-tonnage basis, it has become increasingly necessary that more study be given to the geological relation of gypsum to anhydrite. It was while attempting to work out some definite system of quarry operation for several operators that the factors relating to hydration as given in this paper became apparent. For convenience the words "the formation" are used to mean anhydrite and gypsum taken together as one bed geologically and forming a distinct unit from the rocks below or above. Also, the word "block" is used geologically to define a portion of the formation that is cut apart and separated by erosion from other portions. The formation is part of the Lower Carboniferous, the remainder of which is made up of red shales and shaly sandstones, coarse red conglomerates and limestones. Overlying the Lower Carboniferous are the even-bedded gray sandstones of the coal measures. To a large extent these sandstones have been eroded from above the formation and the usual cover is clay and unconsolidated sediments. The position of the limestone member which immediately underlies the formation usually furnishes the key to the general structure. Being harder, and subject to less erosion, it has a wider spread than the'formation, and measures for dip read on it have a value which can not be applied to dips taken on gypsum or anhydrite. This limestone usually is not more than 25 ft. deep, but it has a remarkable tenacity—one would almost say elasticity—under strain of earth movements. In many cases it stands as a barrier to the erosion which otherwise would have destroyed completely the remaining block of the formation. No bedded limestone is found within the formation except in narrow seams close to the bottom and in short irregular masses in highly disturbed strata where it has been caught up by fault action. This paper is not concerned with the general theories of original deposition and no opinion is expressed as to whether gypsum or anhydrite was first deposited from evaporating sea water. For purposes of study, and as an observed fact, except in the few cases where there has been extreme disturbance, a block of the formation is regarded as a block of anhydrite which has become partly hydrated into gypsum. 177

Jan 1, 1931

By T. M. Morris

The forces acting between a small rod, one end of which was made water repellent, adhering to a much larger air bubble in water were measured. An equation is deduced which correlates these forces and the influence of each force is discussed. The importance of the size of bubbles in a flotation cell is emphasized.

Jan 1, 1950

By John F. Abel

In the debate between miners and ecologists, our industry has at last begun to get some of its story told. I have been told many times that it is hopeless to even try to get our side across. Some are sure that no one will believe us even when our cause is just. My reply would be that we have to tell the truth; again, again, and again. We will never convert a fanatic, but we must try to reach the reasonable and thinking people. I am encouraged because more of us are trying. Various mining companies here in Arizona have bought newspaper space to set forth some of the facts around our local environmental problems. The Arizona Mining Association co-sponsored a symposium in March: Mining and Ecology in the Arid Environment. The symposium program included tours arranged with local mining companies. The participants saw an acid plant, an acid leaching operation, an alluvial tailings dike, a tailings pond, a smelter, and a couple of open pit mines. This wouldn't phase you until you realized that half the visitors were ecologists, watershed and wild- life managers, and other assorted conservationists. It took a lot of guts. I am proud that we had that much confidence. As Pogo said, "We have met the enemy and they is us!" Actually, we met the enemy and they were just like us-concerned.

Jan 1, 1970

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.1, 2' To effect satisfactory separation of the gangue, pre-dominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose.V here is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential," and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products. Ore Preparation The ore used in this experiment was a wash-ore tailing obtained from the western Mesabi range. Microscopic examination and x-ray analysis of the ore showed it to consist of hematite, goethite, and quartz. Physical properties of the iron minerals ranged from hard and crystalline to earthy and ocherous. The quartz grains were discolored either because of iron-oxide inclusions or because of a sur-face coating of iron oxide. The ore assayed 27.52

Jan 1, 1954

By C. W. Sherman, J. Chipman, H. I. Elvander

J. F. Elliott—This is an excellent piece of work and makes a chemical metallurgist more enthusiastic than ever about what can be done with multicomponent systems, if we have satisfactory data. I have a remark to make on the interpretation of fig. 5. First, I will comment on the problem of activities in solutions. The iron-sulphur system has in its phase diagram an intermediate solid phase FeS. The occurrence of an intermediate phase is normally associated with negative departures from Raoult's law over a portion of the activity curves in the liquid. (Perhaps it would be better to reserve the phrase "departure from ideality" to departures from Raoult's law line rather than to departures from Henry's law line). Fig. 5 indicates that the deviation of the sulphur activity curve from the Henry's law line is negative;

Jan 1, 1951

By J. F. Lazenby, W. F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test method's used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1983

By D. D. Pollock, G. P. Conard II

Equations of the form of the Mott and Jones equations for the absolute thermoelectric powers of metals are derived primarily from a thermodynamic approach. The behaviors of transition thermoelements in common use are then examined and compared with this simple theory. MOTT and ones' derived a general expression for the absolute thermoelectric behavior of metals and alloys using the approach of the solid state physicist. This expression was then applied to specific cases.1,2 The present work develops equations of the same form principally by a thermodynamic approach. These relationships are then employed to gain some insight to the behavior of the transition thermoelements in common use. I) DERIVATION OF AN EXPRESSION FOR ABSOLUTE THERMOELECTRIC POWER First consider a metallic conductor which is maintained in a temperature gradient with no current flowing. At constant pressure, there will be a gradient of the free energy (F,) given by:

Jan 1, 1963

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By C. E. Gregor

Current modern trends in mining show that hoisting shafts are being expected to fulfill an important ventilation function. However, where rigid guides and supporting structures are mandatory, ventilating power costs will be high, unless the transverse structures (shaft sets) are streamlined. In the complex configurations of hoisting shaft furniture patterns, either for original design purposes, or for the adjustment of an existing shaft, a useful degree of aerodynamic optimization, by reduction of overall resistance, can only be effectively evaluated by model studies in a special purpose wind tunnel, as described herein. The author has shown that, in one particular case, an annual power cost saving of more than $50,000 was indicated, mainly by the selection of buntons and dividers of improved aerodynamic profile. Mining companies are now realizing the advantages that can accrue through proper attention to the aerodynamic aspects of mine shaft design. With progressive demands of civilization for an ever greater supply of coal and metals, and with greater depths of working, higher rates of extraction, advanced degrees of mechanization, and improved standards of environmental health and work comfort, shaft design is becoming an extremely important aspect of mining operations. In addition, because the cost of sinking, equipping, maintaining, and operating a mine shaft is continually increasing, there is a greater incentive to use a shaft for the maximum duty, consistent with economy. The current natural tendency is therefore to sink multi-purpose shafts, to install as much equipment as is safely and effectively possible to operate; and then, over and above all these functions, to use the shaft to its maximum possible ventilating capacity, as a major, or auxiliary, airway. Clearly, this latter additional function can only be employed at a significant cost, since the most economic operating airways are smooth-lined and devoid of internal rigid furniture. It is true that hoisting functions can be carried out in such shafts if rope guides are used, but only under restricted conditions. Where a manway must be provided, fixed guides and supporting structures are mandatory, and ventilation costs become accentuated. It is generally recognized that the prime element of cost in ventilating a mine can be represented by the power required to drive the fan unit. It is also known that the largest component of total mine resistance is that of the downcast shaft, where this shaft is equipped with rigid guides for hoisting purposes. The pressure loss varies directly as the resistance of the shaft, in accordance with a modification of the Atkinson equation p = RQ2/3600. Furthermore, the air horsepower drawn is given by the equation AHP = (p x 0/33000. Therefore, the power required to drive the fan unit varies as the resistance of the shaft and the cube of the air quantity. Clearly, if Q is a specified minimum, then the only way to minimize the pressure loss (and the power costs) is to reduce the shaft resistance R. (See Table I for a list of symbols.) The resistance to airflow of a shaft equipped with rigid guides and supporting structural sets consists of two components which, for the sake of analytical simplicity, can be regarded as additive. 1) Frictional resistance, represented by the viscous frictional forces within the boundary layer, as air flows along the surfaces of the walls and the periphery of the vertical elements (guides, pipes, cables, ropes, etc.) of the furniture. The friction loss can be readily calculated by the Atkinson equation, after selection of a suitable value for the friction factor K from the McElroy compilation.' KxLxO xQ2 5.2 xA3 Friction loss can be minimized by lining the shaft walls (particularly if of circular or elliptical cross-section) with a smooth continuous lining of monolithic concrete.

Jan 1, 1968

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980