Search Documents

By E. M. Cox, T. Rosenqvist

IN a recent investigation, carried out at the Institute for the Study of Metals, the affinity of sul-phur for iron, copper, and manganese was studied over the temperature range 700" to 1300°C.' It was found that copper exhibits a rather high affinity for sulphur, especially at higher temperatures; and attention was called to the possibility that copper when present together with sulphur in liquid steel would tend to lower the chemical activity of sulphur and thus interfere with the desulphurization process. It was clear, however, that the data for the equilibrium between pure copper and pure copper sulphide (Cu2S) could not give any quantitative information about the effect of copper when dissolved in liquid steel. The present work is concerned with the activity of sulphur in the diluted range of the binary iron-sulphur system, and with the influence of small amounts of copper on this sulphur activity. This investigation is in principle based on the same method previously described for the binary metal-sulphur studies;1,2 namely, reaction with hydrogen to form hydrogen sulphide. The equilibrium ratio PH2s/Ph2 in the equilibrium gas mixture is, for a given temperature, directly proportional to the sulphur activity. The activity of sulphur in liquid iron has previously been studied by Chipman and Ta Li,3 White and Skelly,4 and recently by Sherman, Elvander, and Chipman.5 Morris and Williams6 have studied the effect of added silicon, and Kitchener, Bockris and Liberman,7 and recently Morris and Buehl,8 the effect of added carbon on the sulphur activity. In present day steelmaking processes the steel bath contains between 0.01 and 0.1 pct sulphur, and the copper content may be as high as 0.5 pct. The equi-librium gas ratio (H2S/H2) would, for such a low-sulphur content, be too low to be measured with the experimental technique we use. It has been shown by previous investigators that the H2S/H2 ratio is closely proportional to the sulphur content up to about 1 pct sulphur. The sulphur activity at very low-sulphur content can therefore be calculated by linear interpolation between 0 and 1 pct sulphur. In order to show the general trend with increasing sulphur content, the present work has been carried out to about 3.5 pct sulphur. As the effect of copper was assumed to be more a function of the Cu/S ratio than of the absolute copper content, the runs with copper were made for certain constant values for this ratio.

Jan 1, 1951

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74' and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

By Robin P. Gardner

A radioisotope tracer method combined with a suitable back-calculation method is proposed and evaluated for the determination of model simulation parameters in open-circuit continuous ball mills. The method essentially consists of using impulse and/or step injections of short-lived radioisotopes of the naturally occurring trace elements manganese and sodium. It is evaluated here on the basis of the minimum standard deviations of the product weight-size distributions. These minimum standard deviations are taken as those predicted by a Poisson distribution of the number of particles present in size fractions of the samples taken for analysis. Previously developed tanks-in-series lumped parameter models are used in the evaluation. The results indicate that the method is very promising.

Jan 1, 1976

By W. Buchanan, O. Johari

STEREOGRAPHIC projection has been one of the most useful aids in crystal-structure studies. With the increasing use of electron microscopy in metallurgy and other fields, stereographic projection is being used in many ways1 to interpret the results from electron diffraction patterns and transmission micrographs. For many of these applications, e.g., trace analysis, twinning, and so forth standard projections of various indices are required.

Jan 1, 1967

By Arnulf Muan, Klaus Schwerdtfeger

Activity-composition relations in Pt-Cr and Pd-Cr alloys of low chromium concentrations UCr < 0.3) have been determined in order to ascertain quantitatively the extent of reactions to be expected between Cr2O3-containing oxide phases and platinum or palladium crucibles used as containers in studies of oxide equilibria at low oxygen pressures. This work is a continuation of similar work previously

Jan 1, 1965

By A. Dubé, G. Letendre, C. E. Beaulieu

An experimental study has been made of the time dependence of internal .friction and modulus of rigidity in- freshly quenched steels at room temperature. The effects of frequency, composition, and various thermal treatments are given. The kinetic 1aws observed cannot be fully explained by the so-called first stage of tempering and the transformation of retained austenite. It is suggested that the observed phenomena are due to the progressive immobilization of dislocations introduced by the martensitic transformation. It is generally agreed that the conversion of tetraginal martensite into cubic ferrite and ce-mentite occurs in three stages which at moderate rates of heating take place in the following temperature ranges:&apos;-3 a) The first stage involves mainly a partial loss of tetragonality of martensite and the formation of ?-carbide between 95" and 175oC. b) The second stage consists of the decomposition of retained austenite between 230 and 290&apos; C. c) The third stage covers the formation of ce-mentite between 290o and 400&apos; C. The kinetic laws of these heterogeneous reactions have also been the subject of isothermal studies. Thus, Roberts, Averbach. and cohen3 report a very low reaction rate with a eutectoid steel at room temperature. For example, less than 10 pet of the contraction associated with the first stage is observed after 50 hr at room temperature. Hollonlon, Jaffe, and Buffum4 show that under the same conditions less than 10 pet of the tetragonality is lost. These results have led to the belief that martensite is a relatively stable phase at room temperature. On the other hand, it is well known that important structural changes occur in martensitic steels during the first few minutes at room temperature after quenching. This pretempering has at least two important consequences. In the first place, freshly quenched steels have a tendency to crack at room temperature, a fact which leads to the necessity of tempering as soon as possible after the quench. Another important consequence of pretempering a steel for short periods of time at room temperature is the stabilization of the retained austenite. Thus, as shown by Cohen,5 a very pronounced stabilization is effected with holding periods of 30 min at room temperature. Since these two effects are apparently not caused by the heterogeneous reactions mentioned above, they must be related to the rearrangement of structural defects within the martensite and retained austenite. According to the modern theory of dislocations, the shears required to effect the austenite-marten-site transformation may be realized through the motion of dislocations at the austenite-martensite interface and within the martensite plates.6 In this way, a martensitic transformation closely resembles a plastic deformation. In cold-worked solids, high concentrations of dislocations are left immediately after the plastic deformation and it seems reasonable to assume that appreciable densities of dislocations should also appear in the wake of a martensitic transformation. A considerable part of the high hardness of martensite would then originate in the obstruction of dislocations in analogy

Jan 1, 1961

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.&apos;," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young&apos;s modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith&apos;s well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By C. M. Wayman, R. Bullough

The selection rules fir twinning in fcc, bcc, and hcp lattices as established in Part I are used to predict the positions, relative to the matrix (untwinned) reciprocal lattice, of reflections due to double diffraction from the twins. These doubly diffracted reciprocal lattice points, which often coincide with ordinary matrix reciprocal lattice points, are deduced from kinematical considerations. 1. INTRODUCTION. A Bragg diffracted beam under certain conditions may be rediffracted to produce a third beam i .e., the incident beam, the first diffracted beam, and the rediffracted beam). In such a case an initial incident beam is diffracted by a set of planes; the diffracted beam may then be rediffracted by a second set of crystallographically different planes. The initially diffracted beam acts as an incident beam for the second set of planes, thus resulting in a twice-diffracted beam. This twice-diffracted beam may be regarded as a singly diffracted beam from a set of lattice planes whose structure factor is zero. In order to find the reciprocal lattice point corresponding to the doubly diffracted beam, it is customary1,2 to combine vectorially the component reciprocal lattice vectors which head to the extra reflections. For example, hcp metals may exhibit the forbidden (0001) reflections.* As Fig. 1 shows, the (0001) reciprocal lattice point results from: (1010) + (1011) = (0001) Similarly, combination of the beams (1011) and (1010) gives rise to: (1011)- (1010) = (0001) As Pashley and stowell2 have pointed out, even if in fact the double diffraction points lie on the Ewald sphere, they may not actually represent observed doubly diffracted beams because the initially diffracted primary beam, i.e., the source, must also correspond to a reciprocal lattice point which lies on the sphere of reflection; however, the reciprocal lattice point corresponding to the planes causing the rediffraction need not lie on the sphere. A little consideration of the Ewald construction in Fig. 2 makes this argument clear. In Fig. 2 the incident beam is represented by the wave vector ko. This beam is initially diffracted by the lattice planes (hkl) which are represented by the reciprocal lattice vector r(hk1) The reciprocal lattice point (hkl) of course lies on the Ewald sphere in order that the Bragg condition be satisfied. The initially diffracted beam is represented by the wave vector kl. If now kl is rediffracted by a second set of planes (h&apos;k&apos;l&apos;) resulting in k2 the lattice point (h"k"l") must lie on the Ewald sphere if the double diffracted beam k2 is to be observed. It is clear that (h"k"l") is the vector sum of (hkl) and (h&apos;k&apos;l&apos;), and that (h&apos;k&apos;l&apos;) need not in fact lie on the Ewald sphere. In the usual1,2 analysis the origin (000) of the reciprocal lattice is shifted to the point (hkl). However the translation (000)— (hkl) automatically shifts the point (h&apos;k&apos;l&apos;) to the Ewald sphere, i.e., (h&apos;k&apos;l&apos;)— (h"k"1"). It is to be seen that (hkl), the source reflection, must lie on the Ewald sphere; if it does not the translation (000) — (hkl) places the "new" origin off the sphere, not satisfying the Ewald construction and hence the Bragg condition. The point (h"k"1") of course must lie on the sphere if it corresponds to an observed doubly diffracted beam. It is to be noted that crystals having the hcp structure, as just discussed, are intrinsically capable (i.e., without lattice defects such as twins) of double diffraction, as contrasted to fcc and bcc crystals which are extrinsically capable (requiring lattice defects or reoriented lattice regions). The "allowed" bcc reciprocal lattice points (which comprise an fcc lattice) are (110), (2001, (211), (220), (310), (2221, (321), (4001, and so forth. The combination

Jan 1, 1967

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor counties is due to the influence of what is known as the Cisco Arch (so called because of its influence on Cisco deposition), the axis of which extends in a north\lest-southeast direction across Archer County. Discussion of Tables Preliminary to discussing developments during the year 1933, it appears advisable to offer a few words of explanation on Tables 1 and 2, included as part of this paper, in which an effort has been made to sumlllarize oil and gas development in North Texas to Jan. 1, 1934. One of the chief objectives of this publication is understood to be to show production by individual pools, and, if possible, by distinct pays in a pool. This the authors haw been unable to do for North Texas. It is a generally recognized fact that there are well over 100 individual pools, which should perhaps be mow properly called "productive spots," in Archer county alone, with perhaps an even greater number in Wichita County. It can be found upon investigation that an apparently continuous productive area covering Many acres consists of a half dozen lenticular sands, all stratigraphically different,, which produce only under portions of the apparently continuous area. It is also a fact that practically all gross production records are carried by the various intcrcsted parties by major districts or by counties. It is obvious therefore

Jan 1, 1934

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By William A. Hustrulid

INTRODUCTION Prior to the mid-1970&apos;s, the U.S. Radioactive Waste Disposal Program was focused on salt deposits as the geologic medium of choice, almost to the exclusion of other rock types. These efforts are illustrated by the Project Salt Vault experiment in a salt mine at Lyons, Kansas, in 1965-1967 followed by attempts to locate a repository site in central Kansas. Preliminary evaluation of other geologic media led, in 1978, to the GAIN (Geotechnical Assessment and Instrumentation Needs for Nuclear Waste Isolation in Crystalline and Argillaceous Rocks) Symposium held at the University of California (Berkeley), for the purpose of preparing a state-of-the-art document together with research needs for some of the other possible rock types. Because possible sites had not been selected, nor would they be for some time, the primary emphasis was for research and development focused on generic rocks and generic sites. A basic ground rule at that time was that the host rock formation should provide the primary containment for the waste. Also, the U.S. Nuclear Regulatory Commission (NRC) was just drafting the proposed rules regarding site suitability so that this input was not available. The collection of baseline data, conduction of some critical experiments both in the laboratory and field, and the performance of scoping studies were deemed needed. Such work was indeed undertaken; and to date, a great deal of information has been compiled and much has been learned regarding the characteristics of rock masses, rock behavior

Jan 1, 1984

By D. W. Smith

The beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.&apos; R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 6 phase in the system copper-zinc takes the form of needles lying parallel to a [Ill] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [ill] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective ß phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum. Segregation of the a Phase from the ß Phase in the Copper-tin System Preparation of the Alloy.—An alloy containing 74.92 per cent (by weight) of copper and the balance tin was chosen for this investigation. This alloy, as can be seen from a portion of the constitutional diagram, Fig. 1, of the system copper-tin by Hamasumi and Nishigori,3 with the proper heat treatment should segregate the « phase out of the a parent, solid solution phase. The alloy was prepared from high purity cathode copper (analyzing 99.98 per cent Cu) and Straits tin (analyzing 99.94

Jan 1, 1933

By C. G. Dunn, J. L. Walter

A study has been made of the nature of the slow growth or nucleation stage of secondary recrystallization to the cube texture in sheets of high-purity 3 pct SiFe. Cube-oriented nuclei were identified and their growth observed, using surface markings together with micrographic and X-ray techniques to provide information on grain boundary interactions and the driving forces for growth. FACTORS that promote growth of certain grains during the early stages of secondary recrystallization have been considered theoretically1 but have been little explored in a direct experimental way. In certain cases,2&apos;3 it has been reported that the primary recrystallization grains (nuclei), which eventually become secondaries, were found to be larger than the other grains into which they grew-Factors such as grain boundary "mobility" and differences in strain energy may contribute to the

Jan 1, 1961

By J. C. Karcher

GEOPHYSICAL methods have been more extensively applied to prospecting for oil during 1936 than at any previous time. Their use has been extended to include al- most every oil and gas producing area in the United States. More than ten magnetometer parties, more than nine gravimeter parties, more than five electrical surveying crews, more than fifty torsion balance parties, more than two hundred seismic reflection parties, and several refraction parties were- operating in the United States throughout the year. A tendency has been noted to abandon the use of the pendulum for geophysical prospecting in the oil fields and to increase the use of the

Jan 1, 1937

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By J. M. Stuart, G. D. Bengough, A. R. Lee

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By A. R. Lee, G. D. Bengough, J. M. Stuart

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years&apos; practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916