Search Documents

By Alexander Field

IN THE light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and I Egan,1 it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550° C., when concentrations of carbon and. FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant-a circumstance which might have been predicted from theoretical considerations. At 1550° C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved -CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550° C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020/0.0086 = 2.3 per cent. effective FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By Hillary W. St. Clair

An equation is derived for the rote of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing. The equation takes into consideration the reaction rate coefficient, transport through the gas and through the porous shell of reduced oxide, the rate of gas flow, THIS paper describes a mathematical study of the chemical and physical processes that determine the rate of reduction of solid metal oxide with a reducing gas. The study was a part of a theoretical study leading to the development of a mathematical model for the simulation of the thermochemical behavior of the iron blast furnace. An essential feature of such and the volume of- space surrounding the sphere available for gas flow. The equation is applied to experimental data on vote of reduction of iron oxide in hydrogen. The equation serves as a model for predicting the course of reduction of a particle of. metal oxide in a shaft furnace. a model is an adequate mathematical relationship defining the rate of reaction in terms of all the important chemical and physical phenomena that affect the rate of reaction. This includes not only the reaction rate coefficients, equilibrium ratios, gas composition, and temperature, but also the relevant physical properties of the oxide, rate of gas flow, and relative volumes occupied by gas and solid. In many previous experimental studies of the rate of reduction of oxides by hydrogen or carbon monoxide, the rate of reduction was assumed to be controlled primarily by the chemical reaction at the

Jan 1, 1965

By M. B. Holt

At this time, when electricity in its various applications is attract- ing so much interest, and with such good reason, it has been suggested to me that, as the Aspen Mining and Smelting Company, of Aspen, Pitkin county, Colorado, was the first mining company in America to employ electrical power for hoisting, a record of what has been accomplished by this company would be of interest. Early in the year 1888 the question of power for the development of the ore-horizon lying below the level of the tunnel through which the property is worked, became one of importance. The conditions under which it was proposed to use power were as follows (See Fig. 1): The company's mines lie upon the northwestern slope of a mountain, the ascent of which is at an angle of 28' from the horizon. The ore, consisting of argentiferous galena and other silver-bearing mineral, is found at or near the plane of contact of a superincumbent mass of blue limestone, with an underlying bed of dolomite. This contact plane dips north 30° west, at an angle of 60' with the horizon. A tunnel 1000 feet in length, driven south into the mountain near

Jan 1, 1892

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1983 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 1, 1979

By P. A. Larssen, P. R. Gage, R. W. Bartlett

The kinetics of formation of intermediate sili-cide compounds from MoSi2/Mo and WSi2/W couples were studied using a cylindrical sample configuration. Concentration profiles of the constituent metals were deter mined from electron-microprobe analysis of cross-sectioned samples after isotlzernzal diffusion annealing. These data also yielded hand widths of phases. Growth of intermediate phases depends on diffusionin them and obeys a parabolic rate law. The rates of formation of the intermediate phases decrease in the order Mo5Si3 > W5Si3 > Mo3Si. Crowth rates. for the isomorphous phases Mo5Si3 and W5Si3 had the same activation energy. 43 kcal per mole. SILICIDE coatings employed to protect refractory metals from high-temperature oxidation are usually formed by a diffusion process requiring concurrent transfer of silicon to the refractory metal surface. For a simple binary system and a coating thickness of one or two mils, the coatings on molybdenum and tungsten are primarily the disilicides WSi2 and MoSi2, respectively. During use of the coated re- fractory-metal system at high temperatures, in the absence of the silicon source, further diffusion causes growth of lower silicide compounds and depletion of the disilicides. Recent investigations have shown that the lower silicides are less effective than the disilicides in forming a glassy oxide film which impedes oxidation.' Consequently, failure of coatings at high temperatures may coincide with complete conversion of the disilicide phase. The purpose of this part of the study is to investigate the growth kinetics of the intermediate compounds in the W-Si and Mo-Si systems. There are three intermetallic compounds in the Mo-Si system: MoSi2 with a tetragonal structure

Jan 1, 1964

By C. Richard Honeycutt, Frederick C. Langenberg, Guenter Pestel

Otto Schaaber (Institut für Harterei-Technik, Bremen-Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

By A. E. Jenkins, O. C. Roberts, D. G. C. Robertson

Using an inverted-cone coil at 450 kHz, it has been possible to levitate iron (FeS), cobalt (CoS), and nickel (NiS) sulfides. Important nontransition metal sulfides such as ZnS, PbS, and Cu2S have proven impossible to levitate although Cu-Fe-S ternary alloys containing 30 wt pct S and up to 10 wt pct Cu, and Cu-Co-S and Cu-Ni-S ternary alloys containing 30 wt pct Cu have been levitated. The levitation technique has been used in preliminary experiments on the vaporization from liquid sulfides and the reaction of liquid metal-sulfur alloys with oxidizing atmospheres. The course of the reactions with pure oxygen were followed using highspeed photography and two-color pyrometry. ELECTROMAGNETIC levitation is now established as a basic laboratory technique in high-temperature research but its application has been restricted mainly to metals and alloys. Applications have included alloy preparation,' metal purification,2'3 determination of liquid metal densities and emissivities,4,5 and studies of metal supercooling,4 alloy thermodynamics,6 and vaporization phenomena.7-9 The application of the technique to compounds has not been considered previously. The successful investigation of the reactions between dilute iron alloys and oxidizing atmospheres10'1 has prompted the current physico-chemical studies involving levitated metal sulfide drops and flowing inert or oxidizing atmospheres. This paper presents the results of such a study and provides a basis for future studies involving a wide range of other compounds of metallurgical interest. The successful levitation of many metal sulfides and mattes provides a method of studying the oxidation reactions fundamental to flash-smelting and similar pyrometallurgi-cal operations under closely controlled laboratory conditions. In addition the system allows the use of a controlled atmosphere (e.g., a gas stream of a certain H2/H2S ratio) with a particular chemical potential to study the relevant thermodynamic equilibria or the mass transfer processes between the atmosphere and the levitated drop under conditions where the hydrodynamics of the system can be closely defined. The optimum frequency for the levitation melting of metals in an inverted-cone coil type inductor is within the radio frequency range 400 to 500 kHz. At frequencies lower than 10 kHz the rate of heat generation is usually insufficient to melt the levitated charge' or where melting is achieved, "dripping" from the charge is encountered.'' At frequencies above 2 mHz the levitation force decreases. Metals, alloys and preheated elemental semiconductors such as germanium and silicon, have been levitated but the levitation of only a few metal compounds has been reported. Jostsons13 and the authors have levitated liquid titanium-oxygen alloys containing 50 at. pct 0 while clark14 has reported the levitation of mixtures of FeS and MnS for short periods. With a "cold crucible" inductor sterling15 has melted ferrites by preheating them by induction in a 4 mHz field and melting at a lower frequency. However this second type of inductor has been designed purely for the melting of materials without contamination; there is only a small gas film between the charge and the inductor and the electromagnetic levitation effect is of secondary importance. For this reason further discussion will be restricted to the use of the coil type inductor. The assessment of the suitability of a particular metal compound for levitation is based upon the following two criteria: i) thermal stability, and ii) physical "levitability". In this paper these two criteria will be considered separately. The thermal stability of a solid or liquid metal compound with respect to a gaseous environment depends upon its chemical reactivity with that environment or, in the case of an inert atmosphere considered here, its volatility. The physical criterion as to whether or not a particular compound can be levitated is based upon a comparison between those physical properties of the compound determining "levitability" which are defined by the fundamental equations of levitation theory as developed by Okress et a1.,16 and the properties of the metals. Since it is not practical to cover the vast field of metal compounds, further discussion will concentrate on the metal sulfides but the treatment would be applicable to any metal compound. THE THERMAL STABILITY OF METAL SULFIDES The temperatures usually encountered during levitation in inert atmospheres cover the range 1400" to 2000°C. The stabilities of the condensed states of the sulfides under these conditions are considered in relation to the periodic classification by reference to Table I. Two general classes of sulfides emerge. The solid sulfides of elements of group IIB and of groups further to the right are volatile while those sulfides of group IB and of groups further to the left are nonvolatile solids. The sulfides described as volatile may be dismissed as unsuitable for levitation. The stabilities of the more favorable nonvolatile sulfides under the anticipated conditions must be studied more closely From Table I it is seen that the alkali metal sulfides exist as liquids in the temperature range of in-

Jan 1, 1970

By E. Gybbon Spilsbury

Everybody who has had his attention turned to the gold-deposits of the Southern States, is acquainted with the undisputed fact of the existence, at least in the Carolinas and Georgia, of enormous areas of gold-bearing rocks. Long before the discovery of the precious metal in California, gold-mining on a very extensive scale mas a well-estab-

Jan 1, 1887

By S. V. Krishnan, I. Iwasaki

In the upgrading of finely disseminated iron ores, selective desliming is the critical step that must be controlled to achieve efficient flotation. A prerequisite for selective desliming is a properly-dispersed pulp; sodium silicate is commonly used as a dispersant. The mechanism by which sodium silicate acts as a dispersant in the presence of calcium ions was examined by streaming potential measurements, settling tests, abstraction density determinations, selective flocculation tests, and scanning electron microscope observations. The study established that calcium silicate precipitates on the mineral surfaces dispersed the pulp. Although sodium silicate was a nonselective dispersant, the addition of corn starch aided flocculation of goethite over quartz at low silicate additions, but became ineffective at higher silicate levels. A model is presented to explain the dispersant mechanism of sodium silicate in the presence of calcium ion for selective flocculation of iron ores.

Jan 1, 1983

By J. Bruce Wagner, Roger L. Levin

Integrated forms of two solutions of Fick's second law for the movement of a plane interface through a sample of wustite, and for diffusion into a semi-infinite slab of wustite, are shown to yield nearly identical values of the chemical diffusion coeffcients of cation vacancies in wustite, over the temperature range 900° to 1100°C. The chemical diffusion coefficients, the values of D obtained for the propagation of a concentration gradient through samples of undoped and doped wustite, are obtained from the equations It is becoming increasingly important in metallurgical practices to understand the role of the chemical diffusion coefficient, i.e., the diffusion coefficient of a species across a concentration gradient. During the first stages of sintering, one of the mechanisms by which the bonds between neighboring particles develop is by volume or bulk diffusion. This diffusion coefficient as deter- where ?m is the weight change at any time t, ?W is the total weight change at t =8, A is the area of the specimen, and AC is the total change in the cation concentration after the establishment of equilibrium, as determined by reduction experiments in different carbon monoxide -carbon dioxide mixtures within the limits of existence of the single-phase field. mined from the standard equations for volume diffusion during sintering is actually a chemical diffusion coefficient, and it has been observed to be many times larger than the self-diffusion coefficient as determined on the same materials by experiments using radioactive tracer techniques. Kuczyn-ski1 has noted that, if the controlling mechanism of sintering of A12O3 in an oxidizing atmosphere is the diffusion of oxygen, then this diffusion coefficient as measured from sintering rates is about 2.2 x 104 higher than the self-diffusion measurements obtained by tracer techniques. He has also reported the diffusion coefficient obtained from the rate of sintering of Fe2O3 powder to be about 10 6 times faster than the self-diffusion coefficient of

Jan 1, 1965

By H. O. Hofman

Lime-roasting is a term proposed by Ingalls' for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse un-decomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale,—the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent. of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1908

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By J. E. Dreier

The Pachuca - Real del Monte district has produced about 46.6 kt (51,300 ton) Ag from subvolcanic vein deposits. Three types of wall rock alteration are spatially related to the veins: K-feldspar, propylitic, and phyllic. K-feldspar alteration occurs within veins; propylitic alteration occurs in fractured rocks between veins; and phyllic alteration occurs above veins. Concentrations of some trace elements in altered rocks relative to unaltered rocks are summarized below. [ ]

Jan 1, 1983

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By D. B. Reger

DAVID B. REGER.-T Want to 'add that since this paper was prepared a well is now being; drilled it the location recommended do the last page. It was not, however, done at my instance; it was done at the instance of Dr. White, the State- Geologist of West Virginia, who has been trying for several years to induce the large oil and gas companies to make a test of some of these, deep sands in West Virginia and a well is now just being started in Wood County, right at this immediate

Jan 4, 1917

MELTING in a hearth and in a basket is almost the same thing; charcoal and bellows are used for both. These are made large or small according to the quantity that you wish to melt, and more or less force of the bellows is applied according to the need. The hearth, bowl, or refinery, as the masters call it, is made with bricks and clay like a forge; opposite the middle of the tuyère a round hole is made like a wash- basin, wide at the mouth and narrow at the bottom where there is a hole for emptying it. A little iron plug is put in this so that it may be closed when necessary, or a piece of brick that is cut and pointed. Now, when this has been well covered all over with ashes, and the tuyère has been arranged so that the wind strikes the center, it is first filled with charcoal and baked very well so that the metal may be kept hot once it has been melted. When it has been baked, it is again filled with charcoal, fire is applied, and it is left to inflame gradually by itself. Then put one or

Jan 1, 1942