Search Documents

By A. D. Hoagland

The Flat Gap mine is located on Copper Ridge in the Appalachian Valley of East Tennessee. Large zinc orebodies occupy zones of solution and collapse breccias in Lower Ordovician Kingsport limestone and dolomite. The principal ore mineral is sphalerite and the principal gangue is dolomite. The ore-bearing horizons are considerably more than 95% covered by thick residual clay. Geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap mine. The Flat Gap mine, an important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolcrmite and accessory pyrite. There is local minor galena and very rare barite and fluorite. The ore-bearing horizons are covered by about 20 to 100 ft or more of residual clay except where active streams have exposed bedrock. Considerably less than 5% of the favorable host rocks are exposed in outcrop, and this nearly complete soil cover creates a serious obstacle to exploration. Comprehensive surveys of the base metal content of soils furnish a useful substitute for outcrop geology, and under favorable conditions, this technique is a very valuable prospecting tool. The analysis is carried out by a titrametric dithizone method modified after the procedure described by E. B. Sandell.' This method detects

Jan 1, 1962

By W. A. Koehler, M. E. Hinkle

THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: 1. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of ferrous (iron) sulphate and some sulphuric acid. 2, The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages normally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio-6aciZZus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not Yet been established. Apparently it does not Promote the oxidation of ferrous iron compounds in mine drainage to the ferric state. The second organism has not been identified by name but is described as " Gram negative, non-spore-forming rods approximately 0.4 micron wide by 0.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur compounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced Percentage of Oxygen and increased percentage of carboll 'dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. Acid Coal Mine Drainage Acid coal mine drainage has been the concern of coal mine operators, industrialists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1949

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By R. E. Reed-Hill, W. H. Hartt

The "(3034) " twin lamellae in magnesium have been reexamined using electron microscope replicas. The double twinning sequence (1011)- (1012) for these lamellae has been reconfirmed. Evidence is presented showing that the irrational habit of these twins is probably the direct result of a need to accommodate the second-order twinning shear. This accommodation vesults in both an external shear in the matrix and an internal shear in the lamella. A model is presented which accounts for the experimental obseruations. HCP metals are generally characterized by strong textures in which the basal planes of the grains tend to be aligned parallel to the rolling direction in sheet or plate and to the axis of wires and rods. Since these directions are normally those in which finished products may be subjected to uniaxial tensile stress, these textures effectively place the crystals of magnesium objects in orientations unfavorable to both basal slip and {1012) twinning, the easily activated deformation systems of this metal. However, when magnesium crystals are deformed near room temperature by a tensile stress nearly parallel to the basal plane, another mode of deformation can occur.&apos;,2 This is _a double twin which forms first by twinning on {loll), followed by retwinning on (1012). The resulting twin lamellae are of considerable interest. First, they can be responsible for "brittle fracture&apos;&apos;; when a tensile stress axis lies in the basal plane, because the reoriented crystal structure of a lamella is well-aligned for slip while the parent crystal is not. Extensive internal deformation may thus occur while the matrix is still almost undeformed. This deformation can produce a ductile rupture running the length of the twin.3 Complete failure of the specimen may then oc-cure by the spreading of cracks from one twin lamella to another, or by the movement of a crack into a grain boundary and then along grain boundaries. Since the the volume fraction of these doubly twinned elements is normally very small, the fracture may be classed as brittle, although the fracture mechanism is, of itself, essentially ductile. It is quite probable that the ductility transition, normally observed4 in magnesium at or slightly Obove room temperature, is closely associated with these second-order twins. The detailed relationship of these twins to fracture in single crystals will be the topic of another paper. The present paper is concerned with a second important aspect: the irrational habit of these double twins that falls close to {3034), or approximately 7 deg away from the primary (10il) twin habit. There is good reason to believe that this habit results directly

Jan 1, 1968

By F. V. Lenel

Two years ago in Chicago a seminar was held on the theory of sintering of pure metal powders. As an introduction to this seminar D,.. Rhines1 gave an excellent survey of the literature on this subject, His method of presentatioll was to summarize the experimental observations on sintering and from them to develop a composite theory of sintering in which he combined all the important contributions to the theory into one organic whole. In contrast to the mechanism of sintering of pure metal powders, which, of course, al\vays takes place in the solid phase, sintering j,, the presence of a liquid phase, cannot be treated as one unified mechanism, such as the sintering mechanism of pure metals. The reason is that there are really several mechanisms depending upon the type of alloy system which is sintered and the field of its con. stitutional diagram ill which the sintering takes place, Two mechanisms have heen investigated and will be reviewed in this paper. Ill the first lnechanism the liquid is presellt during the entire time while the compacts are at the sintering temperature, In other words they are sintered between the liquidus and the solidus of the alloy system and are ~e~erogelleous during the entire sintering cycle. The second mechallism applies to alloys in which the liquid phase is formed during the sintering process, but disappears before the sintering process is completed through diffusion and formation of a solid solution. These alloys are therefore homogeneous at the end of the sintering cycle. This second mechanism is more complicated because of the two stages of sintering, the liquid and the solid, as they may be called. It is therefore not surprising that the few detailed investigations of sintering in the presence of a liquid phase have been concerned with heterogeneous sintered alloys, namely the tungsten-nickel-sinter ing which is the so-called "heavy alloy," and the cemented carbides. The mechanism of sintering of these systems is characterized by the fact that theoretical or near theoretical density is attained during sintering, while simultaneously a distinct grain growth takes place through solution of the smallest grains of the solid phase in the liquid phase and reprecipitation on the larger grains. In the first part of the survey this sintering mechanism which is called for short the heavy alloy mechanism is treated in detail. In the second part Of the survey experimental observations for the sintering of homogeneous sintered alloys where the liquid phase disappears before the completion of sintering are discussed. Much less systematic work has been done on these alloys to which the conlmercially important Porous bronzes and the iron-nickel-aluminum permanent magnet alloys belong. Emphasis will be laid throughout this survey upon the microstructural and density changes during sintcring because the Sintering mechanism can usually be described directly by these changes. Other

Jan 1, 1949

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work&apos; the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,&apos; Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By W. E. C. Coxe

MANY of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission was accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned ; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which be furnished for the head of the rail could not be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,&apos;. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955

By H. R. Deeth, C. J. Koenig

About ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spencel described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Cory. at Rochester, N. Y. The Deposit Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 Volumetric Mineral Per Cent Albite.................... 54 Microcline................ 20 Nepheline................ 22 Muscovite................ 2 Mafics.................... 2 (Biotite, hastingsite, magnetite) Total................... loo The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2oA12O3 6SiO2) and microcline (K2O A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1949

By Ross W. Smith, Nikhil Trivedi

The variation of point of zero charge (PZC) of both simple and complex oxide minerals was studied as a function of aging time in water. In most cases the PZC&apos;s of the simple oxides moved toward more basic pH values with aging time. Evidence to date suggests that this phenomenon relates to dissolution of disturbed layers on the mineral&apos;s surface accompanied by later readsorption of metal hydroxy species back onto these surfaces. The readsorption takes place after the solution becomes supersaturated with respect to some crystalline phase. The variation of PZC&apos;s of complex oxides as a function of aging time in water is apparently related to several different mechanisms. In a few cases PZC shifted toward more basic values with time. This shift could be attributed to much the same mechanism as for simple oxides. In most cases, however, PZC of complex oxides shifted toward more acid values with aging time, probably because of loss to solution of soluble cations whose oxides possess basic PZC&apos;s.

Jan 1, 1975

By S. A. Ford

I would like to call the attention of our Bessemer steel manufacturers to a few facts in regard to the action of the manganese in the spiegel with the oxide of iron in the blown iron. The oxygen is united with the iron as a magnetic oxide, as Gautier asserts, and this oxide is reduced to a protoxide by one atom of the manganese uniting with one atom of the oxygen of the magnetic oxide of iron. This oxide of manganese and the protoxide of iron thus formed unite with the silica which has been formed by the oxidation of the silicon in the pig iron. Mr. Snelus and others

Jan 1, 1881

By S. Shapiro, G. Krauss

We will reply to Dr. Pitsch&apos;s discussion by 1) presenting in greater detail the single surface trace analysis which we performed on the reversed austenite plates in a single parent plate of martensite of known orientation, 2) relating the results of our analysis to the conclusions which Dr. Pitsch makes on the basis of our data, and 3) examining the validity of our selection of twenty-nine individual traces from the over 200 austenite plates which were observed in a surface of this single martensite plate. Fig. 7 shows a standard (001) projection of the martensite plate from which the austenite-martensite interface traces were taken. The traces are plotted on the projection as the small solid circles, and the great circles corresponding to the loci of plane normals which could contain each trace or could intersect the surface plane along the measured directions are also plotted. It can be seen that these great circles intersect at a point which corresponds to the normal of the surface plane on which the traces were observed. Also rate which occurred only at particularly low heating rates, see Figs. 1 and 3 in the paper.2 Since in this case the interpretation of Jana and Wayman is plausible and since we have no alternative to this interpretation, we would like to state only that the existence of a diffusion-controlled reversal at low temperatures seems to be not yet proved beyond any doubt. The author wishes to thank Professor G. Krauss for making available his manuscript prior to publication. It is also a pleasure to acknowledge the lively written discussions, which the author has had with Professors G. Krauss and C. M. Wayman prior to this communication. The financial support of the Deutsche For-schungsgemeinschaft for the work on which this communication is based is also gratefully acknowledged. plotted within small dotted circles which represent a i3 deg scatter in each of the twenty-four unit stereo-graphic triangles are our A and B poles7 and the pole P determined by Kessler and itsch.&apos; The data presented in Fig. 7 permit a direct association of the measured traces and the various proposed habit plane poles for the reversed austenite plates in the martensite crystal. If the sample measurements do in fact

Jan 1, 1969

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-&apos;. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.&apos; For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-&apos;. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.&apos; For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By W. H. Hoffman

During the autumn of 1891, several heavy blasts (each throwing down some 3000 tons of ore) were made on what is known as the Theall side of these mines. Immediately after one of these blasts, the writer found that at least one-third of the ore was largely impregnated with pyrites, and besides this, fully 15 per cent. of the entire blast was composed of irregular lumps of magnetic pyrites. This was a revelation wholly unexpected, as previous examinations by many experts had failed to disclose any such quantity of sulphury ore. Over the center of the Theall tunnel there suddenly appeared a perfect keystone, as it were, of pyrites, 3 feet wide at the arch of the tunnel, 13 feet ride at the top, and 20 feet high. This keystone pinched out in February, 1892; but in that month large blocks of pyrites were more plentiful on or near the western wall, and these deposits extended the entire height of the workings, some 43 feet. The second blast in November, in the face and over, and on each side of the tunnel, was far more surprising. The whole cross-section it exposed was thickly interspersed with layers of magnetic pyrites, ranging in thickness from 10 to 24 inches, and quite irregular in form, while all of the ore carried much more than the usual amount of sulphur in the non-magnetic pyrite. One hundred and fifty-five tons from a portion of this breast (western side), showed the following composition upon sampling and analysis: Per cent. Metallic iron,...45.080 Phosphorus,..........304 Sulphur,...........23.510 And the balance of the blast showed: Per cent. Metallic iron,.....• 33.210 Phosphorus,...........349 Sulphur,.......... 6.680 vol. xxI.-33

Jan 1, 1893

By Robin P. Gardner

A radioisotope tracer method combined with a suitable back-calculation method is proposed and evaluated for the determination of model simulation parameters in open-circuit continuous ball mills. The method essentially consists of using impulse and/or step injections of short-lived radioisotopes of the naturally occurring trace elements manganese and sodium. It is evaluated here on the basis of the minimum standard deviations of the product weight-size distributions. These minimum standard deviations are taken as those predicted by a Poisson distribution of the number of particles present in size fractions of the samples taken for analysis. Previously developed tanks-in-series lumped parameter models are used in the evaluation. The results indicate that the method is very promising.

Jan 1, 1976

By Hamilton Bell, E. W. Webb

RepressuRIng, or gas drive, was first tried in the Seal Beach oil field during the fall of 1927, and was carried on until the spring of 1928. This experiment in the Upper or Bixby zone was highly successful in proving the feasibility of compressing gas to high pressures and also showed great increases in production. The project was discontinued because there were not enough wells to protect the property lines. In the development of the second or Selover zone, many more wells were drilled and after 2½ years of production the gas was depleted so that all producing wells in the zone were either pumping or on gas-lift. Edge-wat&apos;er encroachment and the deepening of wells on neighboring properties to a third zone practically isolated the lease, so that during the spring of 1929 it was considered feasible to repressure the Selover zone on the Bixby lease of the Continental Oil Co. (Marland). As shown on Fig. 1, the main Seal Beach structure is an elongated dome with a northwest-southeast trend, and the north flank is cut by a fault nearly parallel to the axis of the structure. Bixby well No. 24 was chosen for the injection well on account of its location, as it is backed up by the fault and is surrounded by wells that protect the property lines. The results of the test made in the Bixby zone indicated that an injection well on the flanks of the structure would drive oil quickly to up-structure wells but would have a tendency to cause by-passing, while the drive to down-structure wells would be slower but more evenly distributed. Preferably the injection well would have been located on top of the dome but property divisions made this inadvisable. Well 24 had been completed in November, 1928, but on account of gas depletion the well failed to flow naturally. On gas-lift the well had an initial production of 1000 bbl. of oil with 30 per cent. emulsion. This well is 4825 ft, deep, penetrating 200 ft. of oil-bearing formation. At the time the well was prepared

Jan 1, 1930

L. C. Graton, Cambridge, Mass.—The subject of chalcocite occur; rence and its geological significance has, of course, a very important commercial bearing, as shown by the recent remark of a hard-headed mining .man: "This secondary enrichment business is one thing you geologists have put up which we can hang on to, and come out right." Most enrichments of copper ores depend upon the formation Of chalcocite from leaner sulphides. Recently it has been shown that not only does there exist this secondary or derived chalcocite, * but that in certain ores the mineral is present as an initial or original constituent, which therefore we may call primary. The desirability of distinguishing between these two kinds of chalcocite is evident and has recently been emphasized. That constitutes the first problem in this connection. I believe many who are working upon secondary enrichment of mineral deposits are giving much attention to that particular question. It is now possible to distinguish primary from secondary chalcocite in many cases. In such cases, what do we know of the&apos; conditions under which this secondary or derived chalcocite was formed? , This is the second main question in connection with the subject. It is now plain, at least in many instances, that the formation of this derived chalcocite represents a phase of oxidation if we have in mind the primary ore as the thing acted upon. The next important question—and it is most important—is: does such oxidation go on above the zone where the rocks are saturated with water—that is, above the water level—or below, or indiscriminately above and below? Many of you have, or have had, opportunities to study at first hand, day after day, occurrences that&apos; enable valuable conclusions to be drawn upon these and other important questions concerning the formation and significance of chalcocite. It is greatly to be hoped that your testimony will be made available and undoubtedly it will go far toward clearing up some of these doubtful points. John D. Irving, New Haven, Conn.—A short time before this meeting was called, H. V. Winchell, who was unable to be present, requested me to exhibit and describe these two samples of pyrite. (Exhibiting specimens.) They consist of fragments of pyrite inclosed in two small bottles. The first bottle shows fragments of pyrite which were immersed in water carrying copper sulphate but without SO2 for a period of two years. They remained comparatively clear and bright. No chalcocite has been deposited on them. The second bottle shows fragments of

Jan 1, 1915