Search Documents

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 11/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond delays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of 1/2 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock. In the early blasts with millisecond delays it was observed that instead of the usual sharp report, the blast had a muffled sound and vibration was not as perceptible as when simultaneous firing was used. Because many quarry operators were being threatened with injunctions or suits for damages by neighbors who claimed structural damage to their buildings, millisecond delays were tried extensively in quarries. In the majority of these trials, the results were very satisfactory. The seismologists recorded the ground movement created by many blasts and verified the initial observations that millisecond delays could be used to reduce vibrations appreciably. In the past few years the advantages of this principle of nonsimultaneous firing of the charges in blasts has become generally accepted. Today the quarry operator who has vibration troubles, inadequate breakage, and excessive backbreak and has not investigated the possibilities of millisecond delay blasting is ignoring a remedy that has proved satisfactory for many. His complacency may be costing him money. Because of the results attained in quarry blasting, it was logical that millisecond delays should be tried in construction work such as in road cuts. As formations in this type of work are likely to change rapidly with advance of the cut, it is more difficult to evaluate results than in quarry blasting. However, this improved control over timing has been beneficial in limiting throw, promoting fragmentation, and reducing overbreak. In blasting near buildings the reduction in vibration and in throw has been especially helpful. As blasters employed in construction work learn what may be accomplished by closer control over the time of firing of explosives charges, more and more millisecond delays are being used to supplant instantaneous electric blasting caps. Improved Fragmentation Underground With this background of promising results, it was not surprising that millisecond delays should go underground. In limestone mining use of millisecond delays as compared with use of cap and fuse or electric blasting caps showed improved fragmentation in stopes and in slabbing operations. Then an opportunity developed to use millisecond delays in some tunnels being driven in a limestone mine (fig. 1). Using the normal charge employed and merely substituting three millisecond delay periods for three regular delay periods, there was a noticeable difference in the appearance and the position of the pile of rock after a blast. A greater portion of the face was exposed, the crest of the pile was farther from the face, and the pile was heaped high along the center line of the tunnel leaving room to walk along the ribs to the face. Fragmentation was appreciably increased. It gave the impression that the slabs had been thrown against each other with tremendous force, promoting the movement of the broken rock along the center line of the tunnel away from the face. Because the drilling and the charge weights were unchanged, the evidence was convincing that the difference in timing was responsible for the difference in results. Probably a greater portion of the energy from the explosives had been expended in doing useful work on the rock. Zeros followed by two periods of millisecond delays were used in the V cut and in two slabs to either side of the cut in this simple round. When millisecond delays, substituted period for period for regular delays, are first tried in a drift round in a mine, and the usual charge of explosives

Jan 1, 1951

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 11/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond delays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of 1/2 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock. In the early blasts with millisecond delays it was observed that instead of the usual sharp report, the blast had a muffled sound and vibration was not as perceptible as when simultaneous firing was used. Because many quarry operators were being threatened with injunctions or suits for damages by neighbors who claimed structural damage to their buildings, millisecond delays were tried extensively in quarries. In the majority of these trials, the results were very satisfactory. The seismologists recorded the ground movement created by many blasts and verified the initial observations that millisecond delays could be used to reduce vibrations appreciably. In the past few years the advantages of this principle of nonsimultaneous firing of the charges in blasts has become generally accepted. Today the quarry operator who has vibration troubles, inadequate breakage, and excessive backbreak and has not investigated the possibilities of millisecond delay blasting is ignoring a remedy that has proved satisfactory for many. His complacency may be costing him money. Because of the results attained in quarry blasting, it was logical that millisecond delays should be tried in construction work such as in road cuts. As formations in this type of work are likely to change rapidly with advance of the cut, it is more difficult to evaluate results than in quarry blasting. However, this improved control over timing has been beneficial in limiting throw, promoting fragmentation, and reducing overbreak. In blasting near buildings the reduction in vibration and in throw has been especially helpful. As blasters employed in construction work learn what may be accomplished by closer control over the time of firing of explosives charges, more and more millisecond delays are being used to supplant instantaneous electric blasting caps. Improved Fragmentation Underground With this background of promising results, it was not surprising that millisecond delays should go underground. In limestone mining use of millisecond delays as compared with use of cap and fuse or electric blasting caps showed improved fragmentation in stopes and in slabbing operations. Then an opportunity developed to use millisecond delays in some tunnels being driven in a limestone mine (fig. 1). Using the normal charge employed and merely substituting three millisecond delay periods for three regular delay periods, there was a noticeable difference in the appearance and the position of the pile of rock after a blast. A greater portion of the face was exposed, the crest of the pile was farther from the face, and the pile was heaped high along the center line of the tunnel leaving room to walk along the ribs to the face. Fragmentation was appreciably increased. It gave the impression that the slabs had been thrown against each other with tremendous force, promoting the movement of the broken rock along the center line of the tunnel away from the face. Because the drilling and the charge weights were unchanged, the evidence was convincing that the difference in timing was responsible for the difference in results. Probably a greater portion of the energy from the explosives had been expended in doing useful work on the rock. Zeros followed by two periods of millisecond delays were used in the V cut and in two slabs to either side of the cut in this simple round. When millisecond delays, substituted period for period for regular delays, are first tried in a drift round in a mine, and the usual charge of explosives

Jan 1, 1951

By T. D. Tiemann

The chemical and mineralogical composition of Caribbean bauxite ores are described. Extraction of alumina by several processes from both Haiti and Jamaica bauxites is discussed and data presented. IMMENSE deposits of bauxite occur in the Caribbean islands of Hispaniola and Jamaica in the high plateau lands and have been excellently described by 0. C. Schmedeman.' The bauxite occurs as deposits in catchments or etched depressions in Tertiary limestone believed to have been deposited in the Eocene and Oligocene periods.' In appearance both the Haiti and Jamaica bauxites resemble a relatively high iron clay and have indeed been mistaken for such.' They are very soft and friable and disperse readily on vigorous agitation in water. The color range in general is light brown to red. Chemically, the outstanding characteristic of the bauxites is the low silica and high ferric oxide content. The extremely low silica makes them particularly valuable for the production of alumina in the Bayer plant since silica is responsible for the loss of both alumina and soda chemically combined as XNa,OYSiO2,ZAl2O2. The ferric oxide, only traces of ferrous iron are present, offers no interference in the production of high grade alumina. Typical oxide analyses of three types of ore are given in Table I2 and a list of the elements occurring in spectrographic quantities in Table 11." The size of the individual particles in the ore makes successful petrographic examination extremely difficult. The ores contain some relatively coarse grains of heavy minerals such as ilmenite, magnetite, and rutile, but other than occasional crystals of a few microns, the greater portion of the minerals are submicroscopic in size and approach colloidal dimensions. The mineralogic composition of the ores has been investigated by X-ray and differential thermal analysis.' These investigations indicate that the predominant mineral phases present are gibbsite (A1203.3H2O), boehmite (Al2O3.H2O), hematite (Fe2O3), and goethite (Fe2O3-H2O). There is no evidence of the occurrence of diaspore (Al2O3.H2O) in either the Haiti or Jamaica ores, but some type of "amorphous" alumina may be present in some of the bauxites of Jamaica." The temperature stability regions in the alumina-water system have been investigated and are given in recent literature. In the temperature range where the hydrated forms are stable, as determined by hydrothermal bomb methods," ibbsite is the stable phase to 155°C (311°F), boehmite from 155°C (311°F) to 280°C (536oF), and diaspore from 280°C (536°F) to 450°C (842°F). Although quite similar in many characteristics, the Haiti and Jamaica ore show a divergence in mineralogic composition that is reflected in the extractability of the alumina described in later paragraphs. Two principal differences occur in mineralogic composition. The iron-bearing mineral in the Haiti ores is predominantly hematite, while in the Jamaica ores goethite is predominant.4 Directly related to the extraction of alumina are the two minerals, gibbsite and boehmite. Boehmite is relatively high in the Haiti ores and in some of the less soluble Jamaica ores, while gibbsite predominates in the ores in Jamaica amenable to the American Bayer process of extraction. Pedersen and Related Processes In general, all processes for the extraction of alumina involving sintering or fusion of bauxite ores with limestone, soda ash, or a combination of limestone and soda ash followed by leaching, are based on the formation of alumina compounds that. yield alumina soluble in the subsequent leach. The principal idealized reactions in respect to alumina and silica for the three types of processes are as follows: Soda Ash Sinter: A12O3 + Na2CO3 = Na2O-Al2O, + CO2 SiO2 + Na2CO3 = Na2O . SiO2 + CO2 A12O2 + SiO2 + Na2CO3 = Na2O.Al2O8. SiO2 + CO2 Leach (with excess water): H2O + Na2O-A12O3 = 2 NaOH + A12O3 (insolution) H2O + Na2O-SiO2 = 2 NaOH + SiO2 (in solution) Soda Ash— Limestone Sinter: Na2CO2 + A12O3 = Na2O.A1203 + CO2 2CaCO3 + SiO2 = 2CaO . SiO2 + 2CO2 Leach (with excess water): Na2O' A1208 + H2O = 2NaOH + A13O3 (in solution) These latter reactions are the basis of the sinter process currently used for the recovery of soda and

Jan 1, 1952

By Thomas T., Read

ALTHOUGH the first colonists in the area that is now the A United States, whether Spanish, French or English in nationality, were usually keenly interested in the possibilities of mineral wealth, it is a curious and interesting fact that none of them happened upon the mineral deposits that eventually were to make this the greatest mineral-producing country; up to 1800 it would probably have been rated as rather poor in minerals. Spanish explorers traversed the southeastern United States with- , out finding the Appalachian gold deposits that aroused so much interest in the early nineteenth century; Coronado sought in vain for the seven golden cities of Cibola; and the important gold \ deposits of California were not discovered until the political sovereignty of the region had passed from Mexico, which had held it for three centuries. The French also held Canada for nearly two centuries (and the British for another century) without finding the mineral deposits in Ontario and Quebec that now are so important. Though they knew of the copper of the Keweenaw peninsula, the lead ores. of Wisconsin and Missouri, and the coal of Illinois in the seventeenth century, these deposits were all too remote for exploitation. In the area held by Great Britain, iron smelting was planned at Jamestown as early as 1619 and was actually begun at Lynn, Mass., in 1643. The industry grew slowly, at first, but had reached considerable importance before the Revolution. Commercial bituminous coal mining began about 1750 in Virginia but anthracite mining in Pennsylvania was not started until 1800. As a result there was naturally little interest in the technical aspects of mineral prodnction here before 1800 by any except the few people who were actually engaged in it. Students of natural science were much interested in minerals, however. The activities of those who rank as geologists are so thoroughly covered in

Jan 1, 1941

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By E. H. Crabtree, Neil S. Parker

THE custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or four concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to 1/2-in. size in a 3-ft Symons shorthead crusher. After crushing to 1/2-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, to pct and 5 pct of its feed. After No. 1 sampler, the material passes through a mixing barrel and is then crushed to 1/4-in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to too tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex Highweir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fagergrens. Copper-lead differential separation

Jan 1, 1947

By E. H. Crabtree, Neil S. Parker

The custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or lour concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to ½-in. size in a 3-ft Symons shorthead crusher. After crushing to ½-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, 10 pct and 5 pct of its feed. After No. I sampler, the material passes through a mixing barrel and is then crushed to -in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to 100 tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex High weir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fager-grens. Copper-lead differential separation

Jan 1, 1949

Charles Catlett, Staunton, Virginia (communication to the Secretary*): I have had occasion to examine a few of the irondeposits in the immediate section of which Mr. Watson speaks, but have not had an opportunity to visit any of the well-known manganese-deposits. I find the former can be very safely read in light of the information which it is possible to get from the same measnres farther. north, where they are less completely decomposed. In the same way all of his conclusions in regard to the geology of the manganese-deposits bear out their occurrence in Virginia, when we allow for the far more complete decomposition in the section he has so carefully studied. Judging from the same measures farther north, I think he will be safe in agreeing even further with Penrose as to the origin of these ores. Some years ago I carried on prospecting work in these measures in Virginia, in which the iron-ore and manganese-ore were followed down to undecomposed material, and in which their occurrence along a definite line of stratification, and apparently a part of the original bedding, was plainly shown. This is unusual, however, even in the section of which I speak. At Crimora, Virginia, the decomposition is quite complete; at the same time the results of some hydraulic work, which has been done there, disclosed, at the time of my last visit, the manganese interbedded in the residual clay along a definite and distinct plane parallel to the bedding of the underlying quartzite, and which, as is shown at other points, corresponds with the plane of the original material. In view of the phosphorus reported by Mr. Watson as existing in the Cartersville ores, and the not uncommonly prohibitive amount in southern ores, I am interested to know whether

Jan 1, 1904

By AIME AIME

MOST recently elected to the limited group of Honorary Members in the A.I.M.E. is the distinguished Australian metallurgist, Guillaume Daniel Delprat. His citation reads: "in recognition of his distinguished achievement as metallurgist, engineer, and administrator in the production of ferrous and nonferrous metals," Mr. Delprat's ability and experience in both the ferrous and nonferrous fields at once distinguishes him from most of his professional brothers. Mr. Delprat's nativity was neither Australian nor English, for he was born in Delft, Holland, in 1856, and educated in Amsterdam. At the age of 22 he went to Spain, as metallurgist for the Tharsis Sulphur and Copper Co., Ltd. Afterwards he spent some time with the Bede Metal and Chemical Co., which had mines in both Spain and Norway, and of which company he became general manager. Other positions of responsibility held by Mr. Delprat before he went to Australia included the managing directorship of the Cordova Exploration Co., with properties in Spain and Canada; of the Rincon Silver-Lead Mining Co., in Spain; and of the Deloro Gold Mines, in Canada.

Jan 1, 1936

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

By J. A. Eisele

The Bureau of Mines has played an important role in the revival of precious-metal mining underway in the Western United States. During the past 30 years, many techniques used by industry to recover gold and silver were pioneered and developed by the Bureau of Mines. In 1952, technology was developed to strip gold from granular activated carbon and allow the carbon to be reused. In 1969, the heap leaching concept was applied to low-grade gold and silver ores and mine wastes. Heap leaching in conjunction with carbon adsorption-desorption permits very low value material to be economically processed. In 1970, an oxidation treatment based on hypochlorite was developed to increase the recovery of gold from carbonaceous gold ores by cyanidation. In the early 19501s, attempts were made to employ carbon-in-pulp technology to recover gold from ores, but the fixed price of gold and increasing operational costs made the process unprofitable. The Bureau of Mines and Homestake Mining Co. jointly operated a carbon-in-pulp pilot plant, and the technology was used in full-scale production at the Homestake Mine in 1972. In 1973, a pressure stripping method, which decreased the time needed for the stripping step, was developed to desorb gold and silver from carbon. An alcohol desorption method, developed in 1976, also decreased the carbon stripping time. These stripping methods are in commercial use. In 1979, an agglomeration pretreatment was developed that permitted clayey precious metal ores to be heap-leached. Agglomeration-heap leaching technology is being used by at least 30 operations, several of them major gold and silver mines. Almost all precious-metal-mining companies use at least one of the above techniques in production facilities.

Jan 1, 1984

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

By Robert Hunt

The American Institute of Mining and Metallurgical Engineers was the first American technical organization to consider steel-rail specifications and sections. If I am not mistaken, the first contribution on those subjects to the Proceedings of the Institute was presented by Prof. Thomas Egleston, in 1874, and was entitled "Investigations on Iron and Steel Rails made in Europe in the Year 1873.1" The next contribution was Dr. C. B. Dudley's report of his investigation for the Pennsylvania Railroad of the wear of steel rails in their tracks, in 1878, which contribution led to a very memorable discussion that extended through several meetings.2 In 1880, Mr. C. P. Sandberg3 presented an article on rail specifications and inspection and rail sections. This was followed, in 1881, by A. L. Holley,4 in his exhaustive report on the then used American rail sections. The next contribution, I believe, was made by myself' at the Buffalo meeting, in 1888, on steel-rail specifications, which I followed,6 in 1889, by a paper on steel-rail sections. Since that time there have been numerous contributions to the Transactions of the Institute in relation to the manufacture of steel rails. The American Society of Civil Engineers officially took up the investigation of the relation of rail sections to the wear of car wheels in 1888. In the prosecution of this work, the Society appointed a special committee, whose labors extended through several years and resulted in an exhaustive report to the Society in 1893.7 Later, another committee was appointed to consider specifications for the manufacture of steel rails; the labors of this committee extended over a period of several years, a final report8 being made in 1910. It was my fortune to be the secretary of both of those committees.

Jan 9, 1919

By W. Geo. Waring

Introduction THE winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district, presents, few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend in no small measure the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are, really continuations of the Joplin district, the total value of ores produced reached the sums of $34,089,503, and that of the metals, $58,927,941.1 The ores produced in the Joplin district are remarkable on account of their almost uniformly high" metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless clue to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proven beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to he exhausted in time, for ordinary mining purposes, acid it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 9, 1917

ALTHOUGH the first colonists in the area that is now the United States, whether Spanish, French or English in nationality, were usually keenly interested in the possibilities of mineral wealth, it is a curious and interesting fact that none of them happened upon the mineral deposits that eventually were to make this the greatest mineral-producing country; up to 1800 it would probably have been rated as rather poor in minerals. Spanish explorers traversed the southeastern United States with- out finding the Appalachian gold deposits that aroused so much interest in the early nineteenth century; Coronado sought in vain for the seven golden cities of Cibola; and the important gold deposits of California were not discovered until the political sovereignty of the region had passed from Mexico, which had held it for three centuries. The French also held Canada for nearly two centuries (and the British for another century) without finding the mineral deposits in Ontario and Quebec that now are so important. Though they knew of the copper of the Keweenaw peninsula, the lead ores of Wisconsin and Missouri, and the coal of Illinois in the seventeenth century, these deposits were all too remote for exploitation. In the area held by Great Britain, iron smelting was planned at Jamestown as early as 1619 and was actually begun at Lynn, Mass., in 1643. The industry grew slowly, at first, but had reached considerable importance before the Revolution. Commercial bituminous coal mining began about 1750 in Virginia but anthracite mining in Pennsylvania was not started until 1800. As a result there was naturally little interest in the technical aspects of mineral production here before 1800 by any except the few people who were actually engaged in it. Students of natural science were much interested in minerals, however. The activities of those who rank as geologists are so thoroughly covered in

Jan 1, 1941

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By Richard W. Lodge

Several methods, both wet and dry, for the assay of zinc-box residues from the cyanide process, have been described in recent years, and each of them has been claimed to be superior to all others. In the year 1901, a paper, entitled "Assay of Zincy Precipitates," was published ill the School of Mines Quarterly to the purport that the scorification method for the assay of zinc-box residues was absolutely unreliable. In order to shed light on this matter, the following experiments were undertaken by Messrs. C.B. Hollis and F. D. Kehew, undergraduate students at the Massachusetts Institute of Technology. The zine-box residues used were obtained through the courtesy of Mr. H. R. Batcheller. The samples were very rich and varied greatly in the fineness of their condition. SCORIFICATION-ASSAYS. In the preliminary tests, the charge, which was weighed on a chemical balance, consisted of 0.1 Assay Ton of residues mixed with from 30 to 35 grammes of test-lead and placed in a 3-in. scorifier, over this an additional quantity of test-lead (from 30 to. 35 grammes) was placed for a cover, and borax-glass, varying in quantity from 3 to 15 grammes, was sprinkled over the top of each charge of the various assays for a cover. The charges were scarified in a muffle-furnace heated to the ordinary temperature which is used in scorification; in some cases the door of the muffle was left open, while in others it remained closed. Generally, the charges spit badly, especially in the assays that were made with door of the muffle left open, or in those in which the door was opened too quickly. The results of the preliminary assays showed: 1. That in order to obtain approxi-

Jan 1, 1904

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By W. Geo. Waring

The winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district presents few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend, in no small measure, the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are really continuations of the Joplin district, the total value of ores produced reached the sum of $34,089,503, and that of the metals, $58,927,941.l The ores produced in the Joplin district are remarkable on account of their almost uniformly high metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless due to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proved beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to be exhausted in time, for ordinary mining purposes, and it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 1, 1918

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935